Effect of graphite and granite dust particulates as micro-fillers on tribological performance of Al 6061-T6 hybrid composites

Aluminium and its alloys have an ever growing demand in many industries such as aerospace, automotive due to their high strength to weight ratio and corrosion resistance. Our current work focuses on synthesis and tribological studies of precipitation hardened Al 6061–Gr_p–granite dust hybrid composites. Liquid stir casting technique is used for synthesis, precipitation hardening treatment imparted for maximising the hardness before subjecting to two-body sliding wear tests. The variation of wear for different levels of load, speed and composition along with SEM micrographs of the worn surfaces has been investigated. Hybrid combinations of granite dust (2 wt% and 4 wt%) with graphite (2 wt%) show higher tensile strength, hardness and significantly improved wear resistance as compared to the base alloy.     

Steel machining chips as reinforcements to improve sliding wear resistance of metal alloys: Study of a model Zn-based alloy system

Two new steel-reinforced, metal-matrix composites (MMCs), Kirksite+1080 and Kirksite+M2 are developed by adding 25 wt% of AISI 1080/AISI M2 steel machining chips to a zinc-based alloy, Kirksite (4% Al and 3% Cu). The sliding wear resistance of the Zn alloy and the two MMCs, against AISI 52100 steel, is determined under increasing normal load (1–10 N) and temperature (25–150 °C), using a pin-on-disc configuration. The MMCs are found to exhibit superior wear performance under all test conditions. At room temperature, a maximum wear reduction in excess of 70% is obtained for the composites relative to the Zn-alloy at the highest load of 10 N. This reduction is as much as 86% at 150 °C and 1 N for the Kirksite+M2. The wear-reducing ability of the steel reinforcements is generally greater at the more severe contact conditions. The stability of the MMC matrices and recommended limits to the MMC operating temperatures are established using deformation measurements made via dynamic mechanical analysis. The principal wear mechanisms are analysed based on the sliding wear measurements, complemented by optical microscopy and SEM observations, and EDX microanalysis. The results show that the steel chip reinforcements are effective in improving the wear resistance of Zn alloys under severe conditions. Implications for use of low-cost machining chips as reinforcements to create MMCs for improved wear performance, and for recycling/reuse of these chips in advanced structural material systems are discussed.     

Tribological behaviors of hierarchical porous PEEK composites with mesoporous titanium oxide whisker

Hierarchical porous PEEK self-lubricating composites were prepared by mold-leaching and vacuum melting process under high temperature. The tribological behaviors were investigated for the porous PEEK composite and the porous composite after incorporating micro-porogen (NaCl) and mesoporous titanium oxide whiskers. If only micro-porogen was incorporated, the lowest steady state specific wear rate was observed for PEEK composites filled with 30% NaCl. Based on this porous PEEK composite, the effects of mesoporous titanium oxide whiskers and non-perforated titanium oxide whiskers on the friction and wear properties of PEEK composites were studied. Results showed that nano-micro porous PEEK composites with 30 wt% micro-porogen and 5 wt% mesoporous titanium oxide whiskers reached the lowest friction coefficient and specific wear rate, which were recorded as 0.0194 and 2.135×10^–16 m³/Nm under the load of 200 N. Compared with 15 wt% carbon fiber-reinforced PEEK composite which is widely used in industry, the wear resistance of the designed hierarchical porous PEEK composite increased by 41 times, showing outstanding wear resistance.     

Abrasive wear of embossed surfaces with convex domes

Some soil-burrowing animals and other biological organisms living in contact with abrasive materials have surfaces optimized for reducing drag and wear. In this study, bio-inspired embossed surfaces consisting of an array of convex domes are investigated to quantify their abrasive wear resistance properties. The experimental procedure proposed in this work is based on sliding seven different embossed surface specimens against an abrasive material for distances up to 3948.9 m with sliding velocities up to 3.02 m/s. The seven specimens consist of 20 mm-wide convex domes made of bakelite and calcium carbonate fixed to flat steel substrates. Quartz sand particles having three different sizes are used as abrasive material for the tests. Experimental results are analyzed and guidelines for designing embossed surfaces, which are optimized to minimize abrasive wear, are proposed.     

Wear behavior of electroless Ni–P–B4C composite coatings

In this research, the wear of electroless Ni–P and Ni–P–B₄C composite coatings was reviewed. Auto catalytic reduction of Ni in nickel sulfate and sodium hypophosphate bath including suspended B₄C particles with different concentration was used to create composite coatings with 12, 18, 25 and 33 vol.% of B₄C particles. Coatings 35 μm thick were heat treated at 400 °C for one hour in an argon atmosphere and the wear resistance and friction coefficient of heat-treated samples were determined by block-on-ring tests. All wear tests were carried out at 24 °C, 35% moisture, 0.164 m/s sliding speed and about 1000 m sliding distance. Graphs show that an electroless Ni–P–B₄C composite coating with 25 vol.% of B₄C had the best wear resistance against a CK45 steel counterface.     

Low wear metal sliding electrical contacts at high current density

Operation of a low wear (2 × 10^?5 mm³/(N-m)), low contact resistance copper sliding electrical contact was demonstrated. The wear rate of a lightly loaded copper–beryllium metal fiber sliding on a polished copper counterface was insensitive to (DC) current density values as great as 440 A/cm² (in a brush positive or anodic configuration). Low wear and relatively low friction (μ ～ 0.2 to 0.3) was achieved by operating the contact immersed in a liquid medium consisting of a hydrofluoroether with helium cover gas, inhibitingoxidationand providing cooling of the contact. Similar experiments performed in liquid mediums of ultrapure water and dilute (3%) hydrogen peroxide show an order of magnitude increase in wear rate and provide further insight on the role of electrochemically enhanced oxidation and the degraded contact resistance and tribological behavior of non-noble sliding electrical contacts in general. In contrast to high current density slidingin hydrofluoroether, an order of magnitude greater wear rate was observed for similar sliding conditionsin hydrogen peroxide or water without the aid of externally supplied electric potential. A conceptual model is proposed correlatingthe rate of brush wear to fatigue strength and electrochemically enhanced oxidation as a result of high current density transport through the contact. A mathematical expression was derived to calculate the approximate wear volume of a single fiber laterally contacting a slip-ring, based on direct measurement of the wear scar geometry.     

Evolution of wear,roughness, and friction of Alloy 600 superalloy surfaces in water-submersed sliding

Self-mated wear and friction of Alloy 600 superalloy was studied in a water-submersed ring-on-rod configuration, loading the side of a 6.35 mm diameter rod across the flat surface of a rotating annular ring of 100 mm outer diameter and 70 mm inner diameter producing two sliding contacts along the ring. Tests were conducted at sliding speeds of 0.178 and 0.330 m/s for sliding distances of 100 m. Normal loads of 51 and 204 N were applied, and initial R_a surface roughnesses of the rings along the sliding direction were either smooth (～0.2 μm) or rough (～7.5 μm). Increased initial ring roughness caused a ～20-fold increase in rod wear at the lighter load, whereas at the heavier load increased initial roughness only caused a ～4-fold increase in wear. At lower initial ring roughness the 4-fold decrease in normal load caused a large (one order-of-magnitude) decrease in rod wear, whereas for rings of higher initial roughness the 4-fold decrease in normal load caused only minor (2-fold or less) decreases in rod wear. Wear during this 100 m sliding distance only experienced a minor effect from the 1.8-fold change in sliding speed, as did friction. In all cases friction coefficient rapidly settled into the range 0.6–0.7, except in the cases of lower load on rings of lower initial roughness where friction coefficient remained above 1 for most of this sliding duration. At this lower load the initial ～0.2 μm rod roughnesses increased to nearly 0.8 μm by the 100 m sliding distance, whereas at the higher load this same sliding distance resulted in roughnesses returning near to the initial 0.2 μm. It was hypothesized more highly loaded cases also went through initial roughening prior to smoothening back to 0.2 μm roughness within the 100 m sliding distance, and given additional sliding the more lightly loaded cases would also experience subsequent smoothening. Increasing sliding distance to 400 m, roughnesses indicated a smoothening back to 0.2 μm level during those lightly loaded tests, with friction coefficient correspondingly dropping from 1 into the 0.6–0.7 range observed in all other cases. Extended sliding to 400 m at light loading against rings of lower initial roughness also allowed a rod wear rate which increased with increased sliding distance to be observed, approaching the same rate observed against initially rough rings within the 100 m sliding distance.     

Tribological behaviour of carbide-free bainitic steel under dry rolling/sliding conditions

The dry rolling/sliding wear behaviour of Si alloyed carbide free bainitic steel austempered at different temperatures and sliding distances has been evaluated. 60SiCr7 spring steel samples were austempered in a salt bath maintained at 250, 300 and 350 °C respectively for 1 h. Rolling with 5% sliding wear tests were performed using self mated discs for three different test cycles, namely 6000, 18,000 and 30,000 cycles. The aim was to study the wear performance of the 60SiCr7 steel with a carbide-free microstructure containing different amounts of retained austenite. An in-depth microstructural characterization has been carried out before and after the wear tests in order to link the wear behaviour to the microstructure of each sample. The wear resistance has been expressed by means of the specific wear calculated from the mass loss after the tests. The worn surfaces were analysed by scanning electron microscopy and X-ray diffraction. Microhardness profiles were also obtained in order to analyse strain-hardening effects beneath the contact surfaces. The results indicate that the material with highest hardness—the one austempered at 250 °C—exhibited the lowest wear rate in every case. It was also observed that the hardness increment and thickness of the hardened layer increases with increasing the austempering temperature and number of test cycles. Finally, the results appear to indicate that the initial roughness of the samples has no major effect in the wear rate of the samples above 2500 cycles. The higher wear performance of the sample austempered at 250 °C has been attributed to its superior mechanical properties provided by its finer microstructure. It has been evidenced that all samples undergo the TRIP phenomenon since, after wear; no retained austenite could be detected by XRD.     

Tribo-layer and its role in dry sliding wear of Ti–6Al–4V alloy

Dry sliding wear tests were performed for Ti–6Al–4V alloy under a load of 50–250 N at 25–500 °C on a pin-on-disk elevated temperature tester. Worn surfaces and subsurfaces were thoroughly investigated for the morphology, composition and structure of tribo-layers. Ti–6Al–4V alloy could not be considered to possess poor wear resistance at all times, and presented a substantially higher wear resistance at 400–500 °C than at 25–200 °C. The tribo-layer, a mechanical mixing layer, was noticed to exist on worn surfaces under various conditions. High wear rate at 25–200 °C was ascribed to no protective tribo-layer containing no or trace tribo-oxides. As more oxides appeared in the tribo-layers, they presented an obviously protective role due to their high hardness, thus giving a reasonable explanation for high wear resistance of Ti–6Al–4V alloy at 400–500 °C.     

Influence of orientation and volume fraction of Aramid fabric on abrasive wear performance of polyethersulfone composites

In case of fabric reinforced composites of specialty polymers influence of orientation of fabric and its volume fraction on tribo-behaviour is sparingly studied. In our earlier work, we have reported on the influence of amount of Aramid fabric (AF) in polyethersulfone (PES) on abrasive wear performance. However, orientation effect of fabric with respect to abrading plane was not investigated. In this work three orientations of composites of PES containing Aramid (Kevlar 29) fabric with three concentrations 64, 72 and 83 wt.% were selected to study the influence on abrasive wear performance. Composites developed by compression molding technique were characterized for their mechanical and physical properties. The abrasive wear performance of the composites was evaluated by abrading 10 mm × 10 mm × 10 mm sample against silicon carbide (SiC) paper under various loads and two grades of abrasive papers. The fabric reinforcement enhanced the abrasive wear resistance of PES significantly (approximately 1.35–9.46 times depending on the operating conditions). It was observed that 83% fabric composite showed the highest resistance to abrasive wear and impact along with the best tensile strength and elongation properties. Its flexural strength and ILSS values, however, were the lowest. Sixty-four percent fabric composite, on the other hand, showed an exactly reverse trend among the three composites. Among the three orientations, fibres in normal and parallel (N–P) and normal and anti-parallel (N–AP) direction with respect to sliding plane proved to impart maximum wear resistance. N–P was best for light loads while N–AP was best for high loading conditions. Orientation parallel and anti-parallel (P–AP) was least beneficial in this respect. Moreover, the extent of improvement very much depended on the operating parameters such as grit size and load. Benefits endowed due to reinforcement were higher at less coarse grade paper. With increase in load, however, wear rate of composites with N–P orientation increased and for other two orientations it decreased. Thus, for severe operating conditions, N–AP orientation proved to be most beneficial. SEM studies proved supporting for understanding the influence of orientation on wear performance.     

Tribo-oxidation maps for Ti against steel

A fundamental study of wear transition regimes was carried out for a pin-on-disk sliding couple, involving titanium and steel. The sliding speed was varied from 0.38 to 1.5 m s⁻¹ and the normal load from 10 to 50 N. Wear mapping approaches have been undertaken to represent the transitions in wear modes and wear mechanisms regimes, as a function of applied normal loads and sliding speeds and for both pin and disc separately on the basis of experimental results. Dry sliding wear behaviour of steel was characterized by tribo-oxidative wear with high material transfer from the titanium. In contrast, adhesive wear was more prevalent for the titanium and oxidative wear mechanisms led to formation of non-protective films on the surface.     

Improved wear resistance in alumina-PTFE nanocomposites with irregular shaped nanoparticles

Past studies with PTFE nanocomposites showed up to 600× improvements in wear resistance over unfilled PTFE with the addition of Al₂O₃ nanoparticles. Irregular shaped nanoparticles are used in this study to increase the mechanical entanglement of PTFE fibrils with the filler. The tribological properties of 1, 2, 5 and 10 wt.% filled samples are evaluated under a normal pressure and sliding speed of 6.3 MPa and 50.8 mm/s, respectively. The wear resistance was found to improve 3000× over unfilled PTFE with the addition of 1 wt.% nanoparticles. The 5 wt.% sample had the lowest steady state wear rate of K = 1.3 × 10⁻⁷ mm³/N m and the lowest steady friction coefficient with μ = 0.21.     

Sliding wear behavior of hardfacing alloys in a pressurized water environment

In this study, sliding wear behavior of newly developed Fe-base Co-free hardfacing alloy (Fe–Cr–C–Si) was investigated and compared to that of Stellite 6 and Fe-base NOREM 02 in the temperatures ranging from 300 to 575 K under a contact stress of 103 MPa (15 ksi) in pressurized water. The weight loss of Fe–Cr–C–Si was equivalent to that of Stellite 6 over all temperatures range in 100-cycle wear test. The weight loss of Fe–Cr–C–Si 1000-cycle wear test increased almost linearly with increasing temperature up to 575 K. The weight loss of NOREM 02 was nearly equivalent to that of Stellite 6 below 475 K, however, galling occurred above 475 K in 100-cycle wear test. It was also found that the lubrication effect of pressurized water on the sliding wear behavior of the alloys was negligible under the present test conditions.     

Effect of TiB2 particles on sliding wear behaviour of Al–4Cu alloy

Dry sliding wear of Al–4Cu–xTiB₂ (x = 0, 2.5, 5, 7.5 and 10 wt.%) in situ composites have been studied in the peak-aged condition using a pin-on-disc wear testing machine at different loads. The composites were prepared by the reaction of a mixture of K₂TiF₆ and KBF₄ salts with molten alloy. The results indicate that TiB₂ particles markedly improve the wear performance of the Al–4Cu alloy. The wear resistance increases with increase in the amount of TiB₂. The load bearing capacity of the alloy during wear increases in presence of TiB₂ particles. Study of the wear surfaces and debris of both alloy and composites using the scanning electron microscope suggests that the improvement in wear resistance is mainly due to the formation of finer debris.     

Wear characteristics of a diffusion bonded sintered steel with short term surface treatments

A pin on disc machine was used to investigate the tribological behavior of a diffusion bonded sintered steel, with and without surface treatments of steam oxidation and manganese phosphating, over a wide range of speed (0.2–4 m/s) and applied load (4–500 N) in conditions of dry sliding and starved lubrication by oil impregnation of the porous structure of the materials. Besides the calculated wear rates, the wear mechanisms were determined by examination of the components of the rubbing system (sintered pin, disc and generated debris). A transition from a mild to a severe wear regime was identified, denoted by sharp changes of the wear rate. A transient wear regime, interposed between the mild and severe wear regimes, was detected. The rubbing surface quality degradation was in terms of material displacement around the pin circumference due to a delamination wear mechanism. Such regime was detected for the base sintered steel in dry sliding at 1 m/s for the load range 60–80 N and for both surface treatments in oil impregnated sliding at 0.5 m/s for the load range 200–300 N. Oil impregnation of the base sintered steel expanded the mild wear regime towards higher loads throughout the whole sliding speed range compared to dry sliding. For the lower speeds of 0.2 and 0.5 m/s, manganese phosphated samples in dry sliding exhibited higher transition loads compared to the base sintered steel. The lower oil impregnability of the surface treated samples, due to the sealing of porosity by steam oxidation, led to slightly lower transition loads in oil impregnated sliding, compared to the base sintered steel.     

Effect of SiC particles on the friction and wear behavior of Ti3Si(Al)C2-based composites

The non-lubricated, sliding friction and wear behavior of Ti₃Si(Al)C₂ and SiC-reinforced Ti₃Si(Al)C₂ composites against AISI 52100 bearing steel ball were investigated using a ball-on-flat, reciprocating tribometer at room temperature. The contact load was varied from 5 to 20 N. For monolithic Ti₃Si(Al)C₂, high friction coefficients between 0.61 and 0.90 and wear rates between 1.79 × 10⁻³ and 2.68 × 10⁻³ mm³ (N m)⁻¹ were measured. With increasing SiC content in the composites, both the friction coefficients and the wear rates were significantly decreased. The friction coefficients reduced to a value between 0.38 and 0.50, and the wear rates to between 2.64 × 10⁻⁴ and 1.93 × 10⁻⁵ mm³ (N m)⁻¹ when the SiC content ranged from 10 to 30 vol.%. The enhanced wear resistance of Ti₃Si(Al)C₂ is mainly attributed to the facts that the hard SiC particles inhibit the plastic deformation and fracture of the soft matrix, the oxide debris lubricate the counterpair, and the wear mode converts from adhesive wear to abrasive wear during dry sliding.     

Tribology characteristics of magnesium alloy AZ31B and its composites

In this paper, wear characteristics of magnesium alloy, AZ31B, and its nano-composites, AZ31B/nano-Al₂O_3, processed by the disintegrated melt deposition technique are investigated. The experiments were carried out using a pin-on-disk configuration against a steel disk counterface under different sliding speeds of 1, 3, 5, 7 and 10 m/s for 10 N normal load, and 1, 3 and 5 m/s for 30 N normal load. The worn samples and wear debris were then examined under a field emission scanning electron microscopy equipped with an energy dispersive spectrometer to reveal its wear features. The wear test results show that the wear rates of the composites are gradually reduced over the sliding speed range for both normal loads. The composite wear rates are higher than that of the alloy at low speeds and lower when sliding speed further increased. The coefficient of friction results of both the alloy and composites are in the range of 0.25–0.45 and reaches minimums at 5 m/s under 10 N and 3 m/s under 30 N load. Microstructural characterization results established different dominant mechanisms at different sliding speeds, namely, abrasion, delamination, oxidation, adhesion and thermal softening and melting. An experimental wear map was then constructed.     

Tribological properties of surface-modified Pd nanoparticles for electrical contacts

A fully comprehensive study of the tribological behavior of palladium nanoparticles (Pd NPs) capped by tetrabutylammonium chains using a ball-on-disk tribometer under different conditions of applied load, concentration, tribometer motion, linear speed and nature of the counterface is revised. A low concentration of NPs (2 wt%) in tetrabutylammonium acetate was found sufficient to improve the tribological properties due to the formation of a protective transfer film (TF) comprised of metallic Pd. The increase of the applied load (up to 20 N, 1.82 GPa of contact pressure) confirmed the excellent extreme-pressure behavior avoiding the counterfaces from severe wear. After a running-in period whose duration depends on the operating conditions, the TF build-up allows to maintain a low contact electrical resistance through the contact (<0.1 kΩ) during the entire test. When the Pd NPs are used with ceramic counterfaces, the nanoparticles increase the load-bearing capabilities and performance of the base without forming TF, likely by mixed or boundary lubrication and healing effects. Finally, the Pd NPs are demonstrated to be useful as a thin solid lubricant film in reciprocating motion yielding a comparable tribological behavior. Hence, the presented surface Pd NPs can be very helpful to extend life of sliding components due to their high strength resistance providing a gateway to electrical conduction as well.     

Effect of the reinforcement (carbon or glass fibres) on friction and wear behaviour of the PEEK against steel surface at long dry sliding

PEEK (poly-ether-ether-ketone) is a high performance engineering semicrystalline thermoplastic. PEEK has excellent tribological behaviour, which is optimised in the specially formulated tribological composite grade.This paper presents a comparative study of wear and friction on PEEK, PEEK-CF30 (wt%) and PEEK-GF30 (wt%) against steel, at long dry sliding. A plan of experiments was performed on a pin-on-disc machine, under the following conditions $pv=2\text{MPa}\text{m/s}$ (p = 8 MPa and $v=0.25\text{m/s}$; p = 2.68 MPa and $v=0.75\text{m}\text{/}\text{s}$) at the ambient temperature for a sliding distance of 15 km.PEEK-CF30 presented the lesser friction coefficient followed by PEEK. PEEK-GF30 presented the higher friction coefficient throughout all sliding distance. Both PEEK-CF30 and PEEK-GF30 have presented an excellent wear resistance relatively to PEEK while PEEK-CF30 presented the best tribological behaviour.     

Synergy between tribo-oxidation and strain rate response on governing the dry sliding wear behavior of titanium

The present work provides an insight into the dry sliding wear behavior of titanium based on synergy between tribo-oxidation and strain rate response. Pin-on-disc tribometer was used to characterize the friction and wear behavior of titanium pin in sliding contact with polycrystalline alumina disk under ambient and vacuum condition. The sliding speed was varied from 0.01 to 1.4 ms^?1, normal load was varied from 15.3 to 76 N and with a sliding distance of 1500 m. It was seen that dry sliding wear behavior of titanium was governed by combination of tribo-oxidation and strain rate response in near surface region of titanium. Strain rate response of titanium was recorded by conducting uni-axial compression tests at constant true strain rate of 100 s^?1 in the temperature range from 298 to 873 K. Coefficient of friction and wear rate were reduced with increased sliding speed from 0.01 to 1.0 ms^?1. This is attributed to the formation of in situ self lubricating oxide film (TiO) and reduction in the intensity of adiabatic shear band cracking in the near surface region. This trend was confirmed by performing series of dry sliding tests under vacuum condition of 2 × 10^?4 Torr. Characterization tools such as optical microscopy, scanning electron microscopy, and X-ray diffractometer provided evidence of such processes. These experimental findings can be applied to enhance the dry sliding wear behavior of titanium with proper choice of operating conditions such as sliding speed, normal load, and environment.