Oxidation of CH4 over Pd supported on TiO2-doped SiO2: Effect of Ti(IV) loading and influence of SO2

Titania-modified silicas with different weight% of TiO₂ were prepared by sol–gel method and used as supports for Pd (1 wt%) catalysts. The obtained materials were tested in the oxidation of methane under lean conditions in absence and in presence of SO₂. Test reactions were consecutively performed in order to evaluate the thermal stability and poisoning reversibility. Increasing amounts of TiO₂ improved the catalytic activity, with an optimum of the performance for 10 wt% TiO₂ loading. Moreover, the titania-containing catalysts exhibited a superior tolerance towards SO₂ by either adding it to the reactants or feeding it as a pure pretreatment atmosphere at 350 °C. Catalysts were characterized by XPS, XRD, FT-IR and BET measurements. According to the structural and surface analyses, the mixed oxides contained Si–O–Ti linkages which were interpreted as being responsible for the enhanced intrinsic activity of supported PdO with respect to PdO on either pure SiO₂ or pure TiO₂. Moreover, the preferential interaction of the sulfur molecule with TiO₂ and the easy SO_x desorption from high surface area silica were the determining factors for the superior SO₂ tolerance of the TiO₂-doped catalysts.     

Structural Study of Copper Oxide Supported on a Ceria-Modified Titania Catalyst System

A structural study of CuO supported on a CeO₂–TiO₂ system was undertaken using X-ray diffraction (XRD) and X-ray absorption spectroscopy (XAS) techniques. The results of XRD revealed the presence of only two phases, TiO₂ anatase and CeO₂ cerianite. A trend towards smaller TiO₂ crystallites was observed when cerium content increased. When the amount of cerium increased, Ti K-edge XANES analysis showed an increasing distortion of Ti sites. The results of Ce L_III-edge EXAFS showed that Ce atoms are coordinated by eight oxygen atoms at 2.32 Å. For the sample containing a small amount of cerium, the EXAFS analysis indicated that the local structure around Ce atoms was highly distorted. The catalysts presented quite different Cu K-edge XANES spectra compared to the spectra of the CuO and Cu₂O reference compounds. The Cu–O mean bond length was close to that of the CuO and the Cu atoms in the catalysts are surrounded by approximately four oxygen atoms in their first shell. Copper supported on the ceria-modified titania support catalysts displayed a better performance in the methanol dehydrogenation when compared to copper supported only on titania or on ceria.     

CO hydrogenation to iso-C4 hydrocarbons over CeO2–TiO2 catalysts

CeO₂–TiO₂ (Ce:Ti = 0.25–9, molar ratio) catalysts were synthesized by a sol–gel method and the catalytic performances were evaluated in the selective synthesis of isobutene and isobutane from CO hydrogenation under the reaction conditions of 673–748 K, 1–5 MPa and 720–3000 h⁻¹. The physical properties, such as specific surface area, cumulative pore volume, average pore diameter, crystal phase and size, of the catalysts were characterized by N₂ adsorption/desorption and XRD. All the CeO₂–TiO₂ composite oxides showed higher surface areas than pure TiO₂ and CeO₂. No TiO₂ phase was detected on the samples of CeO₂–TiO₂ in which TiO₂ contents were in the range of 10–50 mol%. Crystalline Ce₂O₃ was detected in CeO₂–TiO₂ (8:2). The reaction conditions, temperature, pressure and space velocity, had obvious influences on the CO conversion and distribution of the products over CeO₂–TiO₂ (8:2) catalyst.     

Synthesis and characterization of CuO/TiO2 catalysts for low-temperature CO oxidation

In this paper, the CuO/TiO₂ catalysts prepared by the deposition–precipitation (DP) method were extensively investigated for CO oxidation reaction. The structural characters of the CuO/TiO₂ catalysts were comparatively investigated by TG-DTA, XRD, and XPS measurements. It was shown that the catalytic behavior of CuO/TiO₂ catalysts greatly depended on the TiO₂-support calcination temperature, the CuO loading amount and the CuO/TiO₂ catalysts calcination temperature. CuO supported on the anatase phase of TiO₂-support calcined at 400 °C showed better catalytic activity than those supported on TiO₂ calcined at 500 and 700 °C. Among all our investigated catalysts with CuO loading from 2% to 12%, the catalyst with 8 wt% CuO loading exhibited the highest catalytic activity. The optimum calcination temperature of the CuO/TiO₂ catalysts was 300 °C. The XRD results indicated that the catalytic activity of the CuO/TiO₂ catalysts was related to the crystal phase and particle size of TiO₂ support and CuO active component.     

Combined TiO2/SiO2 mesoporous photocatalysts with location and phase controllable TiO2 nanoparticles

Combined TiO₂/SiO₂ mesoporous materials were prepared by deposition of TiO₂ nanoparticles synthesised via the acid-catalysed sol–gel method. In the first synthesis step a titania solution is prepared, by dissolving titaniumtetraisopropoxide in nitric acid. The influences of the initial titaniumtetraisopropoxide concentration and the temperature of dissolving on the final structural properties were investigated. In the second step of the synthesis, the titania nanoparticles were deposited on a silica support. Here, the influence of the temperature during deposition was studied. The depositions were carried out on two different mesoporous silica supports, SBA-15 and MCF, leading to substantial differences in the catalytic and structural properties. The samples were analysed with N₂-sorption, X-ray diffraction (XRD), electron probe microanalysis (EPMA) and transmission electron microscopy (TEM) to obtain structural information, determining the amount of titania, the crystal phase and the location of the titania particles on the mesoporous material (inside or outside the mesoporous channels). The structural differences of the support strongly determine the location of the nanoparticles and the subsequent photocatalytic activity towards the degradation of rhodamine 6G in aqueous solution under UV irradiation.     

Direct synthesis of mesoporous silicalite-1 supported TiO2–ZrO2 for the dehydrogenation of EB to styrene with CO2

Direct synthesis route was developed to support TiO₂–ZrO₂ binary metal oxide onto the carbon templated mesoporous silicalite-1 (CS-1). Metal hydroxide modified carbon particles could play a role as hard template and simultaneously support metal components on the mesopores during the crystallization of zeolites. Such supported TiO₂–ZrO₂ binary metal oxides (TZ/CS-1) showed better resistance to deactivation in the oxidative dehydrogenation of ethylbenzene (ODHEB) in the presence of CO₂. These catalysts were found to be active, selective and catalytically stable (10 h of time-on-stream) at 600 °C for the dehydrogenation of ethylbenzene (EB) to styrene (Sty).     

Hydrodesulphurization performance of NiW/TiO2-Al2O3 catalyst for ultra clean diesel

TiO₂-Al₂O₃ binary oxide supports were obtained by sol–gel methods from Tetra-n-butyl-titanate and pseudoboehmite/aluminium chloride resources. The typical physico-chemical properties of NiW/TiO₂-Al₂O₃ catalysts with different TiO₂ loadings and their supports were characterized by means of BET, XRD and UV–vis DRS, etc. The BET results indicated that the specific surface areas of NiW/TiO₂-Al₂O₃ catalysts were as higher as that over pure γ-Al₂O₃ support, and the pore diameters were also large. The XRD and UV–vis DRS analyzing results showed that the Ti-containing supported catalysts existed as anatase TiO₂ species and the incorporation of TiO₂ could adjust the interaction between support and active metal, and impelled the higher reducibility of tungsten. The hydrodesulphurization (HDS) performance of the series catalysts were evaluated with diesel feedstock in a micro-reactor unit, and the HDS results showed that NiW/TiO₂-Al₂O₃ catalysts exhibited higher activities of ultra deep hydrodesulphurization of diesel oil than that of NiW/Al₂O₃ catalyst. The optimal TiO₂ content of NiW/TiO₂-Al₂O₃ catalysts was about 15 m%, and the corresponding HDS efficiency could reach to 100%. The sulphur contents of diesel products over NiW/TiO₂-Al₂O₃ (from pseudoboehmite/AlCl₃) catalysts with suitable TiO₂ content could be less than 15 ppmw, which met the sulphur regulation of Euro IV specification of ultra clean diesel fuel.     

Influence of Ru segregation on the activity of Ru–Co/γ-Al2O3 during FT synthesis: A comparison with that of Ru–Co/SiO2 catalysts

γ-Al₂O₃ and SiO₂ supported Co catalysts, with varying amounts of Ru, were prepared and evaluated for Fischer–Tropsch synthesis (FTS). The composition of Ru for optimum activity was found to be support-dependent. The reducible Co₃O₄ was high in the region of 0–1.64 wt.% of Ru in Co/SiO₂ catalysts. Co/γ-Al₂O₃ displayed a maximum for reducible Co species at 0.42 wt.% Ru. Segregation of Ru occurred beyond this composition decreasing the extent of reduction. Co/γ-Al₂O₃ catalysts showed lower activity and olefin selectivity, in spite of higher Co dispersion, than Co/SiO₂ catalysts. The catalytic performance depends on the amount of reducible Co species, which again depends upon the optimum content of Ru.     

Effect of molar ratio of TiO2/SiO2 on the properties of particles synthesized by flame spray pyrolysis

Titania (TiO₂)–silica (SiO₂) nanoparticles were synthesized from sprayed droplets of a mixture of TEOS and TTIP by flame spray pyrolysis (FSP). The effect of molar ratio between TEOS and TTIP in the mixture on the particle properties such as particle morphology, average particle diameter, specific surface area, crystal structure, etc., were determined using TEM, XRD, BET, and FT-IR. A UV-spectrometer was also used to measure the absorption spectrum and the band gap energy of the product particles. As the molar ratio of TEOS/TTIP increased by increasing TEOS concentration at the fixed TTIP concentration, the average particle diameter of the mixed oxide nanoparticles increased with maintaining uniform dispersion between TiO₂ and SiO₂, and crystal structure was transformed from anatase to amorphous. The band gap energy of the TiO₂–SiO₂ nanoparticles increased with respect to the increase of the molar ratio due to the decrease of width of UV-absorption spectrum. Photocatalytic activity of TiO₂–SiO₂ composite particles decreased with the concentration of TEOS.     

Effect of ceria on the structure and catalytic activity of V2O5/TiO2–ZrO2 for oxidehydrogenation of ethylbenzene to styrene utilizing CO2 as soft oxidant

The present study was undertaken to investigate the influence of ceria on the physicochemical and catalytic properties of V₂O₅/TiO₂–ZrO₂ for oxidative dehydrogenation of ethylbenzene to styrene utilizing CO₂ as a soft oxidant. Monolayer equivalents of ceria, vanadia and ceria–vanadia combination over TiO₂–ZrO₂ (TZ) support were impregnated by a coprecipitation and wet impregnation methods. Synthesized catalysts were characterized by using X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy, temperature programmed reduction, transmission electron microscopy and BET surface area methods. The XRD profiles of 550 °C calcined samples revealed amorphous nature of the materials. Upon increasing calcination temperature to 750 °C, in addition to ZrTiO₄ peaks, few other lines due to ZrV₂O₇ and CeVO₄ were observed. The XPS V 2p results revealed the existence of V⁴⁺ and V⁵⁺ species at 550 and 750 °C calcinations temperatures, respectively. TEM analysis suggested the presence of nanosized (<7 nm) particles with narrow range distribution. Raman measurements confirmed the formation ZrTiO₄ under high temperature treatments. TPR measurements suggested a facile reduction of CeO₂–V₂O₅/TZ sample. Among various samples evaluated, the CeO₂–V₂O₅/TZ sample exhibited highest conversion and nearly 100% product selectivity. In particular, the addition of ceria to V₂O₅/TZ suppressed the coke deposition and allowed a stable and high catalytic activity.     

Support modification to improve the sulphur tolerance of Ag/Al2O3 for SCR of NOx with propene under lean-burn conditions

Ag/Al₂O₃ catalysts with 1 wt% SiO₂ or TiO₂ doping in alumina support have been prepared by wet impregnation method and tested for sulphur tolerance during the selective catalytic reduction (SCR) of NO_x using propene under lean conditions. Ag/Al₂O₃ showed 44% NO_x conversion at 623 K, which was drastically reduced to 21% when exposed to 20 ppm SO₂. When Al₂O₃ support in Ag/Al₂O₃ was doped with 1 wt% SiO₂ or TiO₂ the NO_x conversion remained constant in presence of SO₂ showing the improved sulphur tolerance of these catalysts. Subsequent water addition does not induce significant deactivation. On the contrary, a slight promotional effect on the activity of NO conversion to nitrogen is observed after Si and Ti incorporation. FTIR study showed the sulphation of silver and aluminum sites of Ag/Al₂O₃ catalysts resulting in the decrease in the formation of reactive intermediate species such as –NCO, which in turn decreases NO_x conversion to N₂. In the case of Ag/Al₂O₃ doped with SiO₂ or TiO₂, formation of silver sulphate and aluminum sulphate was drastically reduced, which was evident in FTIR resulting in remarkable improvement in the sulphur tolerance of Ag/Al₂O₃ catalyst. These catalysts before and after the reaction have been characterized with various techniques (XRD, BET surface area, transmittance FTIR and pyridine adsorption) for physico-chemical properties.     

Solid acidities of SiO2–TiO2/montmorillonite composites synthesized under different pH conditions

SiO₂–TiO₂/montmorillonite composites were prepared under acidic, neutral and basic conditions and the solid acidity of the resulting composites were determined. All the SiO₂/TiO₂ ratio of the colloidal particles was set at 10 but the resulting SiO₂/TiO₂ ratios were significantly richer in TiO₂. The XRD patterns of the acidic composite showed expanding and broadening of the (001) reflection by intercalation of colloidal SiO₂–TiO₂ particles, but the neutral and basic composites showed only broadening of the reflections and no intercalation. The specific surface areas of the acidic, neutral and basic composites (375, 237 and 247 m²/g, respectively) were much larger than of montmorillonite (6 m²/g). The average pore sizes were about 4, 15 and 50 nm, and the amounts of solid acidic sites measured by the NH₃-TPD were 178, 95 and 86 µmol/g for the acidic, neutral and basic composites, respectively. The solid acid amount of the acidic composite was twice that of a commercial catalyst, K-10, (85 µmol/g) and much higher than the guest phase SiO₂–TiO₂ gel (16 µmol/g) or the host phase montmorillonite (6 µmol/g). The TPD peak temperatures reflect the acid strength, and were similar in all the samples, ranging from 175° to 200 °C.     

NOx storage behavior and sulfur-resisting performance of the third-generation NSR catalysts Pt/K/TiO2–ZrO2

The NO_x storage and reduction (NSR) catalysts Pt/K/TiO₂–ZrO₂ were prepared by an impregnation method. The techniques of XRD, NH₃-TPD, CO₂-TPD, H₂-TPR and in situDRIFTS were employed to investigate their NO_x storage behavior and sulfur-resisting performance. It is revealed that the storage capacity and sulfur-resisting ability of these catalysts depend strongly on the calcination temperature of the support. The catalyst with theist support calcined at 500 °C, exhibits the largest specific surface area but the lowest storage capacity. With increasing calcination temperature, the NO_x storage capacity of the catalyst improves greatly, but the sulfur-resisting ability of the catalyst decreases. In situ DRIFTS results show that free nitrate species and bulk sulfates are the main storage and sulfation species, respectively, for all the catalysts studied. The CO₂-TPD results indicate that the decomposition performance of K₂CO₃ is largely determined by the surface property of the TiO₂–ZrO₂ support. The interaction between the surface hydroxyl of the support and K₂CO₃ promotes the decomposition of K₂CO₃ to form –OK groups bound to the support, leading to low NO_x storage capacity but high sulfur-resisting ability, while the interaction between the highly dispersed K₂CO₃ species and Lewis acid sites gives rise to high NO_x storage capacity but decreased sulfur-resisting ability. The optimal calcination temperature of TiO₂–ZrO₂ support is 650 °C.     

The effect of sodium on the catalytic activity of ZnO–Al2O3/ZSM-5 and SnO–Al2O3/ZSM-5 for the transesterification of vegetable oil with methanol

In order to elucidate the effect of sodium on the activity of ZSM-5 supported metal oxides catalysts (ZnO–Al₂O₃/ZSM-5 and SnO–Al₂O₃/ZSM-5) for the transesterification of soybean oil with methanol, ZSM-5 supported metal oxides were prepared with and without sodium hydroxide by impregnation. The metal compositions of the ZSM-5 supported metal oxide catalysts and the metal concentrations dissolved from the catalysts to the methylester phase were measured by SEM-EDS and inductive coupled plasma spectroscopy, respectively. The catalytic activity of ZnO–Al₂O₃/ZSM-5 and SnO–Al₂O₃/ZSM-5 containing sodium did not originate from surface metal oxides sites, but from surface sodium sites or dissolved sodium leached from the catalyst surface.     

Study of ruthenium supported on Ta2O5–ZrO2 and Nb2O5–ZrO2 as catalysts for the partial oxidation of methane

Ru-based catalysts supported on Ta₂O₅–ZrO₂ and Nb₂O₅–ZrO₂ are studied in the partial oxidation of methane at 673–873 K. Supports with different Ta₂O₅ or Nb₂O₅ content were prepared by a sol–gel method, and RuCl₃ and RuNO(NO₃)₃ were used as precursors to prepare the catalysts (ca. 2 wt.% Ru). At 673 K high selectivity to CO₂ was found. An increase of temperature up to 773 K produced an increase in the selectivity to syngas (H₂/CO = 2.2–3.1), and this is related with the transformation of RuO₂ to metallic Ru as was determined from XRD and XPS results. At 873 K and with co-fed CO₂ an increase of the catalytic activity and CO selectivity was found. A TOF value of 5.7 s⁻¹ and H₂/CO ratio ca. 1 was achieved over Ru(Cl)/6TaZr. Catalytic results are discussed as a function of the support composition and characteristics of Ru-based phases.     

Synergetic effect of combined use of Cu–ZnO–Al2O3 and Pt–Al2O3 for the steam reforming of methanol

Commercial Cu–ZnO–Al₂O₃ catalysts are used widely for steam reforming of methanol. However, the reforming reactions should be modified to avoid fuel cell catalyst poisoning originated from carbon monoxide. The modification was implemented by mixing the Cu–ZnO–Al₂O₃ catalyst with Pt–Al₂O₃ catalyst. The Pt–Al₂O₃ and Cu–ZnO–Al₂O₃ catalyst mixture created a synergetic effect because the methanol decomposition and the water–gas shift reactions occurred simultaneously over nearby Pt–Al₂O₃ and Cu–ZnO–Al₂O₃ catalysts in the mixture. A methanol conversion of 96.4% was obtained and carbon monoxide was not detected from the reforming reaction when the Pt–Al₂O₃ and Cu–ZnO–Al₂O₃ catalyst mixture was used.     

Catalytic combustion of chlorobenzene over MnOx–CeO2 mixed oxide catalysts

A series of MnOx–CeO₂ mixed oxide catalysts with different compositions prepared by sol–gel method were tested for the catalytic combustion of chlorobenzene (CB), as a model of volatile organic compounds of chlorinated aromatics. MnOx–CeO₂ catalysts with different ratios of Mn/Ce + Mn were found to possess high catalytic activity in the catalytic combustion of CB, and MnOx(0.86)–CeO₂ was identified as the most active catalyst, on which the temperature of complete combustion of CB was 254 °C. Effects of systematic variation of reaction conditions, including space velocity and inlet CB concentration on the catalytic combustion of CB were investigated. Additionally, the stability and deactivation of MnOx–CeO₂ catalysts were studied by various characterization methods and other assistant experiments. MnOx–CeO₂ catalysts with high Mn/Ce + Mn ratios present a stable high activity, which is related to their high ability to remove the adsorbed Cl species and a large amount of active surface oxygen.     

Low-temperature catalytic combustion of chlorobenzene over MnOx–CeO2 mixed oxide catalysts

MnO_x–CeO₂ mixed oxide catalysts prepared by sol–gel method were tested for the catalytic combustion of chlorobenzene (CB), as a model of chlorinated aromatic volatile organic compounds (CVOCs). MnO_x–CeO₂ catalysts with the different ratio of Mn/Ce + Mn were found to possess high catalytic activity for catalytic combustion of CB, and MnO_x(0.86)–CeO₂ was the most active catalyst, on which the complete combustion temperature (T_90%) of chlorobenzene was 236 °C. The stability of MnO_x–CeO₂ catalysts in the CB combustion was investigated. MnO_x–CeO₂ catalysts with high Mn/Ce + Mn ratios present high stable activity, which is related to their high ability to remove Cl species adsorbed and a large amount of active surface oxygen.     

Growth of Pd particles in methanol synthesis over Pd/CeO2

The metal–support contact structure of Pd–CeO₂ changed with increasing the temperature of reduction. Upon high temperature reduction, severe sintering of Pd particles occurred, while sintering of the ceria support was marginal. The catalytic deactivation of the Pd/CeO₂ catalysts during methanol synthesis was caused by the further structural change in the Pd–CeO₂ contact under reaction conditions. Considerably large Pd particles (about 100 nm) were formed in the catalysts subjected to methanol synthesis, and there was a close correlation between the activity loss and the growth of the Pd particles. It was proposed that the structure of Pd–ceria contact shifted from small Pd clusters supported on ceria to sintered large Pd particles dispersed in a mass of ceria.     

Ceria modified MnOx/TiO2 as a superior catalyst for NO reduction with NH3 at low-temperature

A series of cerium modified MnOx/TiO₂ catalysts were prepared by sol–gel method and used for low-temperature selective catalytic reduction (SCR) of NOx with ammonia. The experimental results showed that NO conversion could be improved by doping Ce from 39% to 84% at 80 °C with a gas hourly space velocity (GHSV) of 40,000 h⁻¹. This activity improvement may be contributed to the increase of chemisorbed oxygen and acidity after Ce doping. TPR results also verified that the redox property of Ce modified MnOx/TiO₂ was enhanced at low-temperature.