The Effect of Glycol Type,Glycol Mixture,and Isocyanate/Glycol Ratio on Flexural Properties of Oil Palm Empty Fruit Bunch-Polyurethane Composites

Abstract

Oil palm empty fruit bunch (EFB)-polyurethane (PU) composites were produced. The effects of the isocyanate (NCO)/glycol (OH) ratio, glycol type, and mixtures (polyethylene glycol PEG 400 (M _w 400) and polypropylene glycol PPG 400 (M _w 400)) on the flexural properties were investigated. The NCO/OH ratio had a significant effect on the flexural properties of the EFB-PU composites. Composites made with PEG 200 exhibited higher flexural properties than with PEG 400 and PPG 400. The flexural properties were also found to be influenced by the PPG 400/PEG 400 ratio.     

Preparation of waterborne polyurethanes using an amphiphilic diol for breathable waterproof textile coatings

The application of polyurethanes (PUs) on breathable waterproof fabric coatings requires a balance of water vapor permeability (WVP) and water resistance which can be achieved by tailoring hydrophilic and hydrophobic segments. PU prepolymers were prepared from isophorone diisocyanate, dimethylol butanoic acid, and a mixture of various ratios of amphiphilic PPG2050 (copolymer of ethylene oxide and propylene oxide with –OH end groups) and hydrophobic poly(tetramethylene ether glycol) (PTMEG). After neutralization with triethylamine, the prepolymers were chain-extended with ethylene diamine/1,4-butanediol (1:1 by molar). The WVP values of the fabric coatings prepared using various waterborne PUs were very similar (910–990 g/m² × 24 h). When waterborne PUs prepared using a mixture of PPG2050 and PTMEG were employed for the textile coatings, the resulting PU-coated textiles exhibited excellent waterproof properties (>10,000 mm H₂O). The textile coatings prepared from PPG2050/PTMEG-based waterborne PUs were significantly more waterproof than those prepared from poly(ethylene glycol) (PEG)/poly(propylene glycol) (PPG)/PTMEG-based waterborne PU. This is probably due to a more even distribution of hydrophobic segments in the PUs, even though the WVP values of the PEG/PPG/PTMEG-based PU coatings were considerably smaller than those of the PPG2050/PTMEG-based PU coatings.     

Aqueous dispersion of polyurethanes from H12MDI,PTAd/PPG,and DMPA: Particle size of dispersion and physical properties of emulsion cast films

Aqueous dispersions of ionic/nonionic polyurethane (PU) were prepared from hydrogenated diphenylemthane diisocyanate (H₁₂MDI), poly(tetramethylene adipate) glycol (PTAd), polypropylene glycol (PPG), monofunctional ethylene-propylene oxide ether, and dimethylol propionic acid (DMPA). The effects of DMPA, PTAd/PPG ratio, and the average molecular weight of PPG on the state of dispersion, mechanical, and viscoelastic properties of the emulsion cast films were determined using Authosizer, Instron, and Rheovibron.     

Oil Palm Empty Fruit Bunch‐Polyurethane Composites: The Effect of Isocyanate/Glycol Ratio,Glycol Type,and Glycol Mixture on Impact Strength,Dimensional Stability,and Thermal Properties

Abstract

In this study, polyurethane (PU) composites have been produced with oil palm empty fruit bunch (EFB) and polyethylene glycol (PEG), molecular weight (MW) of 200 (PEG200), 400 (PEG400), and polypropylene glycol (PPG) with MW of 400 (PPG400) used as polyols. The effect of isocyanate (NCO)/hydroxyl (OH) ratio and PPG400/PEG400 ratio on the impact strength, dimensional stability (immersion test), and thermal behavior were investigated. The study revealed that as the NCO/OH ratio was increased, the impact strength increased, and the absorption and swelling of the composites either in water or dimethylformamide (DMF) decreased. The decrease in the onset and peak temperatures, and the increase in the enthalpy as the NCO/OH ratio was increased from 0.8 to 1.1 were attributed to the disruption of crystalline region due to the occurrence of cross‐linking. As for NCO/OH ratio of 1.1 onward, the increase in onset and peak temperatures were due to the increase in the degree of cross‐linking. On the other hand, the decrease in the enthalpy was due to the formation of allophanates. Thermal behavior of the composites made from the glycol mixture was predominantly influenced by the PPG400.     

Thermal,Mechanical and Chemical Properties of Hydrophilic Poly(vinyl alcohol) Film Improved by Hydrophobic Poly(propylene glycol)

A series of poly(vinyl alcohol)/poly(propylene glycol) (PVA/PPG) blend films with different PPG contents were prepared by casting the polymer blend solutions. Structure and morphologies of the PVA/PPG blend films were studied by Fourier transform infrared spectroscopy (FT-IR) and scanning electron microscopy (SEM). Thermal, mechanical, and chemical properties of PVA/PPG blend films were investigated by differential scanning calorimeter (DSC), thermogravimetric analysis (TGA), tensile strength tests, and other physical methods. It was revealed that the introduction of PPG could exert marked effects on the morphology and the properties of PVA film.     

高支化f-CTBN/PEG聚氨酯的合成与降解性能研究

采用逐步聚合的方法,以功能化丁腈橡胶(f-CTBN)与不同相对分子质量(Mn)聚乙二醇(PEG)共聚合得到一系列高支化嵌段聚氨酯(f-CTBN/PEG)高分子材料。通过对材料溶胀性,模拟生物环境降解,以FT-IR对基团变化分析和ESEM形貌观察,以及力学性能的测试。结果表明:材料的降解速率随时间延长呈减慢趋势,且随PEG含量的增大材料降解越快;拉伸强度(超过18MPa)和杨氏模量(超过40MPa)相对较高。有望根据需求来调节f-CTBN/PEG的比例大小,从而用于医用防护材料的生产。     

Valorization of bio-calcium carbonate based Chamelea gallina shell waste fillers in shape memory polymer composites

In recent years, the focus has been on the use of calcium carbonate-based seashell wastes in the production of new thermoplastic and thermoset polymer materials, paving the way for their use as biofillers in polymeric composites. In this study, it is aimed to obtain a new polymeric composite material by doping Chamelea gallina shells, on polylactic acid (PLA)/polyethylene glycol (PEG) blend. Structural characterization of the obtained PLA/PEG blend/C. gallina composite films was performed with attenuated total reflection infrared spectroscopy (ATR-IR). When the thermal properties of composite materials were examined by thermogravimetric analysis (TGA), it was determined that the thermal stability of polymeric composites increased with the addition of C. gallina. SEM images showed that the polymer blend films, which appeared to have a porous structure, filled the pores with increasing C. gallina ratio. It was observed that the biodegradability of PLA/PEG blend composite films decreased with increasing C. gallina shells addition. However, C. gallina had a positive effect on the swelling and water absorption capacities of polymeric composites. The increase in tensile strength and elongation at break values of PLA/PEG blend/C. gallina composite films with increasing C. gallina means that the mechanical properties of the polymer are improved.     

负载白芨多糖的PU/PAM双网络水凝胶的制备与性能

采用聚乙二醇、Ymer N120、聚丙二醇和异佛尔酮二异氰酸酯为原料,以三乙醇胺作交联剂合成聚氨酯(PU)预聚物,浸入白芨多糖(BSP)和丙烯酰胺(AM)混合溶液,通过自由基聚合制备了负载BSP的PU/PAM双网络水凝胶.采用FTIR、SEM对水凝胶的结构和形貌进行了表征,通过拉力试验机和生物实验对其力学性能和生物性能进行了测试.结果表明,当三乙醇胺用量为多元醇物质的量的60％时,双网络水凝胶具有高溶胀率(256％)的同时保持一定的拉伸强度(1.9 MPa)和高压缩强度(22.7 MPa).双网络水凝胶具有抗菌抗氧化作用,其中,双网络水凝胶对大肠杆菌和金黄色葡萄球菌的抑菌带宽度分别为0.5～4.0和0.5～3.5 mm,羟基自由基清除率最高为28％;溶血率低于5％,细胞存活率最高达101.3％±3.6％,表明双网络水凝胶具有良好的生物相容性.     

Synthesis and characterization of elastomeric polyurethane/clay nanocomposites

An elastomeric polyurethane/clay (PU/clay) nanocomposite based on poly(propylene glycol) (PPG), glycerol propoxylate, and toluene‐diisocyanate (TDI) was synthesized by intercalative polymerization technology. The results of wide angle X‐ray diffraction (WAXD) studies showed that the gallery distance of the clay in the hybrid was enlarged from 1.9 to 4.5nm or more. Introducing clay in the PU matrix resulted in an increase in both the tensile strength and elongation at beak. When the clay content reached about 8%, the tensile strength and elongation at break were two times and five times respectively to that of the pure PU. In addition, the clay intercalative route to the nanocomposite synthesis also effected the thermal properties of the nanocomposites. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1444–1448, 2001     

Preparation of waterborne polyurethanes using an amphiphilic diol for breathable waterproof textile coatings

The application of polyurethanes (PUs) on breathable waterproof fabric coatings requires a balance of water vapor permeability (WVP) and water resistance which can be achieved by tailoring hydrophilic and hydrophobic segments. PU prepolymers were prepared from isophorone diisocyanate, dimethylol butanoic acid, and a mixture of various ratios of amphiphilic PPG2050 (copolymer of ethylene oxide and propylene oxide with –OH end groups) and hydrophobic poly(tetramethylene ether glycol) (PTMEG). After neutralization with triethylamine, the prepolymers were chain-extended with ethylene diamine/1,4-butanediol (1:1 by molar). The WVP values of the fabric coatings prepared using various waterborne PUs were very similar (910–990 g/m² × 24 h). When waterborne PUs prepared using a mixture of PPG2050 and PTMEG were employed for the textile coatings, the resulting PU-coated textiles exhibited excellent waterproof properties (>10,000 mm H₂O). The textile coatings prepared from PPG2050/PTMEG-based waterborne PUs were significantly more waterproof than those prepared from poly(ethylene glycol) (PEG)/poly(propylene glycol) (PPG)/PTMEG-based waterborne PU. This is probably due to a more even distribution of hydrophobic segments in the PUs, even though the WVP values of the PEG/PPG/PTMEG-based PU coatings were considerably smaller than those of the PPG2050/PTMEG-based PU coatings.     

Mechanical properties of poly(l‐lactic acid) composites filled with mesoporous silica

The mechanical properties of mesoporous silica (MCM‐41) filled poly(l ‐lactic acid) (PLA4032D) composites and PLA4032D/poly(ethylene glycol) (PEG) composites were investigated. It was found that the Young's modulus increased while tensile strength decreased with increasing the filler content; the V‐notched impact fracture strengths of both Izod and Charpy for the PLA4032D/PEG/MCM‐41 composites increased while they decreased slightly for the PLA4032D/MCM‐41 composites, the unnotched Charpy impact strength of both the two composites decreased with increasing the filler loading; the flexural modulus increased slightly while the flexural strength decreased slightly with increasing the filler content. The toughening mechanisms of the composites were discussed by means of observing the impact fracture surface with a scanning electronic microscope, and the synergistic effect between the PEG and MCM‐41 should be one of the major toughening mechanisms. POLYM. COMPOS., 38:1118–1126, 2017. © 2015 Society of Plastics Engineers     

水性聚氨酯/聚甲基丙烯酸甲酯杂化乳液的合成

用异佛尔酮二异氰酸酯(IPDI)、聚丙二醇(PPG)和二羟甲丙酸(DMPA)合成了水性聚氨酯分散体(WPU),讨论了PPG摩尔质量,NCO/OH及PPG/DMPA比例对WPU乳液和涂膜性能的影响。以WPU为种子与甲基丙烯酸甲酯进行乳液聚合制备杂化乳液,研究了不同PU/PMMA物质的量比例对杂化乳液及涂膜性能的影响,并采用TEM对WPU及杂化乳液粒子进行了表征。结果表明,在以PPG1000为原料,NCO与OH物质的量比为1.4∶1,PPG与DMPA物质的量比为1∶0.8条件下制备的WPU杂化乳液,随着PMMA比例增加,杂化乳液的稳定性和成膜性变差,聚合物膜断裂伸长率降低,但铅笔硬度、耐水性及耐乙醇性均得到了改善。     

Synthesis of starch‐based plastic films by electron beam irradiation

Starch‐based plastic films were prepared by the electron beam irradiation of starch and poly(vinyl alcohol) (PVA) in a physical gel state at room temperature. The influence of starch/PVA composition, irradiation dose, and plasticizer (glycerol) on the properties of the plastic films was investigated. The gel fraction of the starch/PVA films increased with both the radiation dose and PVA content in the plastic film and decreased with increasing glycerol concentration. The starch/PVA compatibility was determined by measurement of the thermal properties of the starch/PVA blends with various compositions with differential scanning calorimetry. The swelling of the starch/PVA films increased with increasing PVA content and decreasing irradiation dose. Mechanical studies were carried out, and the tensile strength of the films decreased at high starch ratios in the starch‐based mixture. This was due to the decrease in the degree of crosslinking of starch. Furthermore, when PVA, a biodegradable and flexible‐chain polymer, was incorporated into the starch‐based films, the properties of the films, such as the flexibility (elongation at break), were obviously improved. The tensile strength of the films decreased with increasing glycerol concentration, but elongation at break increased up to a maximum value at a 20% glycerol concentration, and then, it leveled off and decreased slightly. Biodegradation of the starch/PVA plastic films was indicated by weight loss (%) after burial in soil and morphological shape, which was detected by scanning electron microscopy. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 504–513, 2007     

Interpenetrating polymer networks based on polyol modified castor oil polyurethane and poly(2‐ethoxyethyl methacrylate): Synthesis,chemical, mechanical,thermal properties,and morphology

Interpenetrating polymer networks (IPNs) of glycerol modified castor oil polyurethane (GC‐PU) and poly(2‐ethoxyethyl methacrylate) poly(2‐EOEMA) were synthesized using benzoyl peroxide as initiator and ethylene glycol dimethacrylate (EGDM) as crosslinker. GC‐PU/poly (2‐EOEMA) interpenetrating polymer networks were obtained by transfer molding. The novel GC‐PU/poly (2‐EOEMA) IPNs are found to be tough films. These IPNs are characterized in terms of their resistance to chemical reagents thermal behavior (DSC, TGA) and mechanical behavior, including tensile strength, Young's modulus, shore A hardness, and elongation. The morphological behavior was studied by scanning electron microscopy. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1029–1034, 2004     

Physico-chemical properties of lignin–alginate based films in the presence of different plasticizers

A lignin–alginate blended film was prepared in the presence of three different plasticizers, viz. glycerol, epichlorohydrin (EPC) and poly(ethylene glycol) (PEG) and the effect of each plasticizer was studied on physico-chemical properties of the blended film. Lignin extracted from Acacia wood by alkali extraction process was blended with alginate to obtain lignin–alginate film in the presence of different plasticizers. A film plasticized with glycerol displayed higher solubility and swelling percentage as compared to EPC and PEG plasticized films. The highest tensile strength was observed for film plasticized with PEG, and none of the plasticizers made any significant change on the bursting strength of the film. Incorporation of lignin considerably improved the light barrier properties of the films. Fourier transform infrared spectroscopy study of films suggested the existence of hydrogen bonding between lignin–alginate in the presence of plasticizers. In addition, EPC plasticized film displayed highest thermal stability, as confirmed by thermogravimetric analysis. Further studies demonstrated that plasticizers significantly affected the physico-chemical properties of the blended films. In conclusion, lignin–alginate film plasticized with EPC presented better physico-mechanical and light barrier properties which could be used in packaging and coating applications.     

Thermal and surface characterization of polyurethane–urea clay nanocomposite coatings

This paper reports synthesis and characterization of polyurethane–urea (PU‐urea) and the nanocomposites derived from the PU‐urea with silicate clays. Organophilic montmorillonite cotreated by cetyl trimethyl ammonium bromide (CTAB) was synthesized and used to prepare PU‐urea/montmorillonite nanocomposites coatings. PU‐ureas were prepared from polyethylene glycol (PEG), polypropylene glycol (PPG), trimethylol propane (TMP), and 4,4′‐diphenylmethane diisocyanate (MDI) by reacting excess diisocyanate with polyether glycols. The excess isocyanate of the prepolymers was cured with atmospheric moisture. The synthesized moisture cured PU‐urea and nanocomposites were characterized by Fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), differential scanning calorimetric (DSC), and angle resolved X‐ray photoelectron spectroscopy (AR‐XPS). The thermal stability of the PU‐urea nanocomposites was higher relative to the mother PU‐urea films. DSC results showed a slight enhancement in the soft segment glass transition temperature after 3 wt % clay loading. The surface properties showed an enrichment of the soft segment toward the surface. An enhancement in the hard segment composition in the nanocomposite coatings has resulted in enhancing the phase mixing process. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2393–2401, 2006     

Tensile properties,degradation behavior,and water absorption of sago starch plastic films

Sago starch plastic films were prepared by a blending and casting method using various amounts of additives. The additives were glycerol (GLY), polyethylene glycol (PEG), and glutaraldehyde (GLU). Results indicated that the films had an optimum tensile strength of about 2.6 MPa and an optimum elongation at break of 74%. Meanwhile, a GLU content of five parts by weight gave the best tensile properties. Elongation at break of the films increased while tensile strength decreased upon increasing the level of plasticizer (GLY and PEG). The addition of plasticizer also increased the water absorption and soil burial degradation rate. However, the addition of GLU gave opposite results. J. VINYL ADDIT. TECHNOL., 2012. © 2012 Society of Plastics Engineers     

Preparations and Properties of Waterborne Polyurethane / Nanosilica Composites

Summary Aqueous dispersion of polyurethane(PU) ionomers, based on poly(tetramethylene glycol) as soft segment, isophorone diisocyanate as diisocyanate, 1,4-butanediol as chain extender, dimethylol propionic acid as potential ionic center, triethylene tetramine as crosslinker, and triethyl amine as neutralizer, were reinforced with hydrophobic nanosilica to give waterborne PU/nanosilica composites. The reinforcing effects of nanosilica were examined in terms of mechanical, dynamic mechanical, and thermal properties together with water swell and transparency of the dispersion cast films. With the addition of nanosilica to PU, tensile modulus and strength increased, and the rubbery modulus increased in magnitude and extended to higher temperature, and these enhanced mechanical and thermal properties, together with increased swell resistance were obtained without scarifying the transparency of the films.     

PEG、PPG改性PLA材料的性能研究

采用熔融共混法用聚乙二醇(PEG)对生物可降解材料聚乳酸(PLA)进行改性,研究了PEG的相对分子质量对共混体系热性能和力学性能的影响,对比了相同相对分子质量的PEG和聚丙二醇(PPG)由分子结构差异对共混体系性能的影响。结果表明,PEG的相对分子质量为2 000时,改性效果最好;相同相对分子质量的PEG改性效果优于PPG。     

Pressure-volume-temperature properties for binary and ternary polymer solutions of poly(ethylene glycol), poly(propylene glycol), and poly(ethylene glycol methyl ether) with anisole

Pressure-volume-temperature properties were measured for polymer solutions of poly(propylene glycol) (PPG)+anisole, polymer blends of PPG+poly(ethylene glycol methyl ether) (PEGME), and the blends of PPG+PEGME and poly(ethylene glycol) (PEG)+PPG with anisole at temperatures from 298.15 to 348.15 K and pressures up to 50 MPa. The Tait equation represents accurately the pressure effect on the liquid densities over the entire pressure range. The excess volumes change from positive to negative as increasing the mole fraction of PPG in the binary systems of PPG+anisole and PPG+PEGME. The volumetric data of the related binary systems were correlated with the Flory-Orwoll-Vrij and the Schotte equations of state to determine the binary parameters. By using these determined binary parameters, both equations predicted the specific volumes of the polymer blends with anisole to average absolute deviations of better than 0.13%.