氧化石墨烯掺杂反渗透混合基质膜制备及性能

由于芳香族聚酰胺反渗透膜在抗污染性以及耐氯性方面存在不足,限制了其在海水淡化等方面的应用。采用往油相中添加氧化石墨烯（GO）的二次界面聚合法改性了商业反渗透膜,评价了GO掺杂反渗透混合基质膜的分离性能和耐氯性能,并用接触角仪、Zeta电位仪、扫描电镜和原子力显微镜等仪器表征了膜的亲水性能、荷电性能以及膜表面形貌。结果表明,GO的添加提高了膜的分离性能、耐氯性能和亲水性能;当GO添加量为30 mg·L^-1时,膜的通量为（77.7±0.9） L·m^-2·h^-1,膜的截留率为97.6%±0.5%,相比商业膜分别提高了38.4%和4.5%。当氯化强度低于4800 mg·L^-1·h时,膜的水通量和盐截留率变化不明显。     

Mixed Matrix PVDF/Graphene and Composite‐Skin PVDF/Graphene Oxide Membranes Applied in Membrane Distillation

This work elucidates the influence of graphene (G) and graphene oxide (GO) content on the desalination performance and scaling characteristics of G/polyvinylidene fluoride (G/PVDF) mixed matrix and GO/PVDF composite‐skin membranes, applied in a direct contact membrane distillation process (DCMD). Inclusion of high quality, nonoxidized, monolayered graphene sheets as polymer membrane filler, and application of a novel GO/water‐bath coagulation method for the preparation of the GO/PVDF composite films, took place. Water permeability and desalination tests via DCMD, revealed that the optimal G content was 0.87 wt%. At such concentration the water vapor flux of the G/PVDF membrane was 1.7 times that of the nonmodified reference, while the salt rejection efficiency was significantly improved (99.8%) as compared to the neat PVDF. Similarly the GO/PVDF surface‐modified membrane, prepared using a GO dispersion with low concentration (0.5 g/L), exhibited twofold higher water vapor permeate flux as compared to the neat PVDF, but however, its salt rejection efficiency was moderate (80%), probably due to pore wetting during DCMD. The relatively low scaling tendency observed for both G and GO modified membranes is primarily attributed to their smoother surface texture as compared to neat PVDF, while scaling is caused by the deposition of calcite crystals, identified by XRPD analysis. POLYM. ENG. SCI., 59:E262–E278, 2019. © 2018 Society of Plastics Engineers     

二氧化钛调控基膜结构对氧化石墨烯复合膜性能的影响

以聚醚砜(PES)超滤膜为基膜,通过聚多巴胺(PDA)表面改性后压力沉积不同量的二氧化钛(TiO₂)纳米粒子作为基底,再沉积氧化石墨烯(GO)片层制得TiO₂/GO复合分离膜,重点考察基膜表面形貌对GO膜分离性能的影响。通过扫描电子显微镜、接触角测试仪、固体表面Zeta电位分析仪、X射线衍射分析仪等对有无TiO₂沉积层的GO复合膜进行表征,并考察TiO₂沉积量对GO复合膜分离性能的影响。结果表明,TiO₂纳米粒子以团簇状态均匀分布在改性的超滤膜表面,随TiO₂沉积量的增加,团簇密度增大,GO沉积后表层的峰谷结构更为明显,但表层的层间距并无明显改变。TiO₂/GO复合膜的水通量随TiO₂沉积量的增加而明显增大,TiO₂的沉积对GO沉积量低的复合膜通量的影响更明显,当 GO沉积量为4.11 μg/cm²,TiO₂沉积量为20.55 μg/cm²时,复合膜的水通量较无TiO₂的复合膜提高了108.38%。复合膜对无机盐溶液的截留性能主要基于膜表面所带负电的道南排斥作用,TiO₂/GO复合膜对刚果红的截留率在99%以上,对甲基橙的截留率可达82%,TiO₂层的加入并未降低复合膜的截留效果。     

Preparation and properties of hollow fibre nanofiltration membrane with continuous coffee-ring structure

Polyamide(PA)hollow fibre composite nanofiltration(NF)membranes with a coffee-ring structure and beneficial properties were prepared by adding graphene oxide(GO)into the interfacial polymerization process.The presentation of the coffee-ring structure was attributed to the heterogeneous,finely dispersed multiphase reaction system and the“coffee-stain”effect of the GO solution.When the piperazine concentration was 0.4 wt-%,the trimesoyl chloride concentration was 0.3 wt-%,and the GO concentration was 0.025 wt-%,the prepared NF membranes showed the best separation properties.The permeate flux was 76 L·m^?2·h^?1,and the rejection rate for MgSO4 was 98.6%at 0.4 MPa.Scanning electron microscopy,atomic force microscopy,and attenuated total reflectance-Fourier transform infrared spectroscopy were used to characterize the chemical structure and morphology of the PA/GO NF membrane.The results showed that GO was successfully entrapped into the PA functional layer.Under neutral operating conditions,the PA/GO membrane showed typical negatively charged NF membrane separation characteristics,and the rejection rate decreased in the order of Na2SO₄>MgSO₄>MgCl₂>NaCl.The PA/GO NF membrane showed better antifouling performance than the PA membrane.     

Development of a novel graphene oxide-blended polysulfone mixed matrix membrane with improved hydrophilicity and evaluation of nitrate removal from aqueous solutions

In this study, four types of mixed matrix membranes were fabricated using polysulfone (as the base polymer) and different contents of graphene oxide (GO) nanosheets (as modifier) through wet phase inversion method. Based on the amounts of GO (0, 0.5, 1, and 2?wt%), the synthesized membranes named as M1, M2, M3, and M4, respectively. The membranes characteristics were evaluated using FE-SEM, FT-IR, and water contact angle measurements. In addition, the performance of the prepared membranes was investigated in terms of basic parameters: filtrate water flux, nitrate removal efficiency, and antifouling properties. Results showed significant improvements of the characteristics of modified membranes with GO. Accordingly, the permeability and hydrophilicity were enhanced and water flux was considerably improved. At operating pressure of 4?bar and nitrate concentration of 110?mg/L, the removal efficiency for unmodified membrane (M1) was 15.5% and for modified M2, M3, and M4 membranes were 22.78%, 39.12%, and 41.37%, respectively. In addition, the results of flux recovery ratio (FRR) showed that the anti-fouling properties of the GO modified membranes were improved due to the increase in membrane surface hydrophilicity.     

Fabrication of novel polyethersulfone based nanofiltration membrane by embedding polyaniline-co-graphene oxide nanoplates

Mixed matrix polyethersulfone (PES) based nanofiltration membrane was prepared through phase inversion method by using of polyvinylpyrrolidone (PVP) as pore former and N, N dimethylacetamide (DMAc) as solvent. Polyaniline-co-graphene oxide nanoplates (PANI/GO) were utilized as additive in membrane fabrication. The PANI/GO nanoplates were prepared by polymerization of aniline in the presence of graphene oxide nanoplates. FTIR analysis, scanning electron microscopy (SEM), scanning optical microscopy (SOM), 3D images surface analysis, water contact angle, water content tests, tensile strength tests, porosity tests, salt rejection and flux tests were used in membrane characterization. FT-IR results verified formation of PANI on graphene oxide nanoplates. SOM images showed uniform particles distribution for the mixed matrix membranes. SEM images also showed formation of wide pores for the modified membranes. Water flux showed constant trend nearly by use of PANI/GO in the casting solution. Opposite trend was found for the membrane surface hydrophilicity. Salt rejection was enhanced sharply by utilizing of PANI/GO. The membrane’s tensile strength was improved by increase of PANI/GO concentration. The water content was increased initially by use of PANI/GO nanoplates up to 0.05%wt into the casting solution and then decreased. Membrane porosity was also enhanced by using of PANI/GO nanoplates. Modified membrane containing 0.5%wt PANI/GO nanoplates showed more appropriate antifouling characteristic compared to others.     

The effects of graphene oxide on the properties and drug delivery of konjac glucomannan hydrogel

Konjac glucomannan (KGM) hydrogel has good potential application in food and medical science, although to achieve this, the physical and mechanical properties need further improvement. In this study, graphene oxide (GO) was used to improve the functionality of KGM hydrogel. KGM/GO hydrogels were prepared by freezing the alkaline KGM/GO sols. Rotational rheometer was used to study the rheological properties of different alkaline KGM/GO sols. Fourier transform infrared, Raman, differential scanning calorimetry, thermogravimetric analyses, and scanning electron microscopy were used to evaluate the structure and properties of the hydrogels. In addition, different pH solutions and an in vitro assay were used to study the swelling property and the release behavior of KGM/GO hydrogels, respectively. The result revealed strong hydrogen‐bond interaction between KGM and GO. The incorporation of GO highly improved the gel properties of KGM/GO sol, higher thermal stability, and more compact structure of KGM/GO hydrogels. KGM/GO hydrogels showed better swelling properties in deionized‐distilled water and pH 7.2 PBS. The release of 5‐aminosalicylic acid (5‐ASA) from KGM/GO (KG4) hydrogel was different in various pH media, but the initial burst release effect was very severe. Therefore, incorporation of GO have a good potential in enhancing the properties of KGM hydrogel, but KGM/GO hydrogel is not an ideal carrier for 5‐ASA release. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45327.     

Thin film graphene oxide membrane: Challenges and gas separation potential

Graphene oxide membranes were prepared by vacuum and pressurized ultrafiltration methods on the 12% modified Polyacrylonitrile (12mPAN) substrate to specify challenges, salient features, future directions, and potential of GO membrane for separation fields using characterization techniques and gas separation test (studied gases are CO₂, He and N2), which is an efficient tool for better understanding of GO membrane behavior. GO membrane structure was examined over a wide range of parameters, such as pore size range of substrate and its surface properties, pH of GO dispersion, GO content, synthesis pressure, operating pressure and temperature. The results show that the GO content does not hold a linear relationship with the permeance and selectivity. Film thickness, aggregates, synthesis pressure defects and interlayer spacing have significant effects on the gas separation performance of GO membranes which originate from the synthesis method and its conditions.     

Preparation of graphene oxide/polyamide composite nanofiltration membranes for enhancing stability and separation efficiency

Polyamide (PA) NF membranes are synthesized on a hollow fiber support by the interfacial polymerization (IP) of piperazine (PIP) and trimesoyl chloride (TMC). Then, GO is coated on the PA layer to decorate the NF membrane surface (denoted GO/PA-NF). This strategy aims to improve the hydrophilicity, chlorine resistance and separation stability of the membrane. The optimization, chemical composition, morphology, and hydrophilicity of the synthesized GO/PA-NF membrane are characterized. Results indicate that the optimized GO/PA-NF in terms of rejection rate and flux are with 0.05 wt% GO. The rejection of GO/PA-NF for Na2SO₄ and MgSO₄ is 99.4% and 96.9%, respectively. Even if the GO/PA-NF is immersed in 1000 ppm NaClO solution for 48 h, the NF membrane still maintains stable salt rejection. The developed NF membranes exhibit excellent treatment performance on dying wastewater. The permeate flux and rejection of GO/PA-NF toward Congo red solution are determined to be 44.2 L/m²h and 100%, respectively. Compared with the PA membrane, GO/PA-NF presents a higher rejection for Na₂SO₄ (99.4%) and a lower rejection for NaCl (less than 20%), which shows that the NF membranes have a better divalent/monovalent salt separation performance. This study highlights the superior performance of GO/PA-NF and shows its high potential for application in wastewater treatment.     

氧化石墨烯改性聚酰胺膜研究进展

聚酰胺膜广泛应用于海水淡化、苦咸水脱盐及废水处理等领域,复杂、多类型的应用场景对膜性能提出了更高要求。氧化石墨烯（GO）以优异的机械、化学稳定性及亲水性等优点引起了学者的广泛关注。利用GO改性聚酰胺膜,可以改善膜的水通量、抗污染及耐氯性等性能。综述了聚酰胺膜在酸性和含氯溶液中的降解过程,介绍了GO结构特征,重点关注了利用GO在聚酰胺膜支撑层中、支撑层与功能层间、功能层中及功能层表面进行改性以提高膜性能的研究进展,对GO改性聚酰胺膜中金属离子及水传质过程进行了简要介绍。最后,提出未来可以从完善GO改性聚酰胺膜抗污机理、提高GO在膜基质中的稳定性、提高GO在溶液中的分散性及增强GO改性聚酰胺膜耐酸性等方面作进一步研究。     

Influence of a graphene oxide additive and the conditions of membrane formation on the morphology and separative properties of poly(vinylidene fluoride) membranes

In this article, we present our study of the influence of a graphene oxide (GO) additive and the method of preparation on the properties of membranes. Poly(vinylidene fluoride) (PVDF)/GO membranes were obtained by an inverse phase method, which was conducted by two different methods. The first one was based on solvent evaporation, and the second method was a coagulation bath in distilled water. Our studies clearly showed that the introduction of the GO nanoadditive into the polymer membrane matrix played a major role in the pore process formation, and it also contributed to the reduction of the contact angle, and this led to an improvement in the hydrophilic properties of the obtained membranes. Furthermore, the PVDF/GO membrane preparation process had a direct influence on the thickness and porosity. Both of these factors had a direct influence on the transport properties of the membrane. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42789.     

Graphene Oxide Hybrid Supramolecular Hydrogels with Self‐Healable,Bioadhesive and Stimuli‐Responsive Properties and Drug Delivery Application

Self‐healable hydrogels are promising soft materials with great potential in biomedical applications due to their autonomous self‐repairing capability. Although many attempts are made to develop new hydrogels with good self‐healing performance, to integrate this characteristic along with other responsive multifunctions into one hydrogel still remains difficult. Here, a self‐healable hybrid supramolecular hydrogel (HSH) with tunable bioadhesive and stimuli‐responsive properties is reported. The strategy is imparting graphene oxide (GO) nanosheets and quadruple hydrogen bonding ureido‐pyrimidinone (UPy) moieties into a thermoresponsive poly(N‐isopropylacrylamide) (PNIPAM) polymer matrix. The obtained GO–HSH hydrogel shows rapid self‐healing behavior and good adhesion to various surfaces from synthetic materials to biological tissue. In addition, doxorubicin hydrochloride (DOX) release profiles reveal the dual thermo‐ and pH‐responsiveness of the GO–HSH hydrogel. The DOX‐loaded hydrogel can further directly adhere to titanium substrate, and the released DOX from this thin hydrogel coating remains biologically active and has high capability to kill tumor cells.     

In situ Synthesis and mechanical,thermal properties of polyimide nanocomposite film by addition of functionalized graphene oxide

Polyimide (PI) and chemical modified graphene oxide nanocomposite films are prepared by in situ polymerization from solutions of pyromellitic dianhydride and 4,4′‐oxydianiline with various amount (0.5–2 wt%) of 3‐aminopropyltriethoxysilane (APTS) functionalized graphene oxide (GO) sheets in dimethylacetamide. The APTS functionalized GO (GO‐APTS) is a versatile platform for polymer grafting, improving excellent dispersion of GO in the PI matrix, and forming strong interaction with the PI matrix. The GO‐APTS/PI nanocomposites exhibited improvement in mechanical and thermal properties by addition of a small amount of GO‐APTS. With the addition of a small amount of GO‐APTS (1.5 wt%) to PI matrix, mechanical properties with the tensile strength and Young's modulus improved by 45% and 15%, respectively. The thermal analysis showed that the thermal stability of PI was slightly enhanced by the incorporation of GO‐APTS (1.5 wt%). This approach provides a strategy for developing high performance functionalized GO‐polymer composite materials. POLYM. COMPOS., 37:907–914, 2016. © 2014 Society of Plastics Engineers     

Chitosan–graphene oxide nanocomposites: Effect of graphene oxide nanosheets and glycerol plasticizer on thermal and mechanical properties

In this study, graphite oxide (GO) is synthesized from natural graphite flakes by the modified Hummers method. Characterization by Fourier transform infrared, X‐ray photoelectron, Raman and ultraviolet‐visible spectroscopies, X‐ray diffraction, and thermogravimetric analysis is conducted on GO to confirm the oxidation of graphite. Unplasticized and glycerol plasticized chitosan/graphene oxide (CS/GO) nanosheets nanocomposites with different GO loadings are prepared by solution casting. The combined effect of GO and glycerol on structure, thermal and mechanical properties of nanocomposite films is studied. GO nanosheets are well dispersed throughout the CS matrix due to the hydrogen bonding and electrostatic interactions between CS and GO nanosheets. The incorporation of GO within the CS matrix results in a decrease of the crystallinity, an improvement of thermal stability, and a significant enhancement of the stiffness and tensile strength that is emphasized by the glycerol. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45092.     

Electrospun PAN–GO composite nanofibers as water purification membranes

Varying amounts of exfoliated graphene oxide (GO) are systematically incorporated into nanoscale polyacrylonitrile (PAN) fibers via an electrospinning method. Subsequent treatment of the PAN–GO composite nanofibers under a moderate temperature and high pressure leads to the formation of membrane sheets with enhanced mechanical properties. scanning electron microscope, Fourier transform infrared spectroscopy, and contact angle measurements confirm the successful incorporation of the GO into the PAN nanofiber membranes whose diameter, porosity, and pore size are notably influenced by the amount of the GO content. These composite membranes also exhibit a gradual reduction in the water contact angle as a function of the hydrophilic GO content, resulting in a beneficial property for water purification. In addition, the proper integration of GO into the PAN nanofibers improves the protein rejection rate and water flux during the filtration process, which indicates the possibility of utilizing these types of composite membranes in water treatment systems. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45858.     

Fabrication of polyamide thin film nanocomposite reverse osmosis membrane incorporated with a novel graphite-based carbon material for desalination

The properties of polyamide (PA) thin film composite (TFC) membranes are affected by many variables, especially the additives in the process of interfacial polymerization that play an important role in the properties of membranes. In this study, a new type graphite carbon was added into organic phase containing trimesoyl chloride for interfacial polymerization with aqueous phase containing m-phenylenediamine to prepare modified polyamide thin film nanocomposite (TFN) membranes for reverse osmosis (RO) adhibition. Polysulfone ultrafiltration membranes were used as the carrier of the interfacial polymerization. The concentration of graphite carbon was selected from 0.002 to 0.01 wt%. The polyamide nanocomposite membrane prepared with the concentration of 0.004 wt% graphite carbon showed the best RO desalination performance, which the water flux of this TFN membrane is over 2.3 times as much as pristine TFC membrane, and the salt rejection is over 99%. This article provides a well-performing polyamide thin film nanocomposite membrane modified by a new-type carbon nanoparticles consequently.     

Plasma surface modification of graphene oxide nanosheets for the synthesis of GO/PES nanocomposite ultrafiltration membrane for enhanced oily separation

In this study, two different monomers, namely hexafluorobutyl acrylate (HFBA) and diethylaminoethyl methacrylate (DEAEMA) were individually used to modify graphene oxide (GO) nanosheets via environmentally friendly plasma enhanced chemical vapor deposition (PECVD) method. The results from instrumental analyses confirmed the successful deposition of respective functional material onto the nanomaterials. Modified GOs were used as the nano-fillers to develop composite polyethersulfone (PES) ultrafiltration (UF) membrane with improved surface properties for oily solution treatment. All the developed membranes were characterized with a series of analytical instruments to support the findings of membrane filtration performance. The results indicated that the membrane incorporated with DEAEMA-GOs (coated with hydrophilic polymer) could achieve better results in terms of oil rejection, antifouling resistance and water recovery rate than the membrane incorporated with HFBA-GOs (coated with hydrophobic polymer). This is due to the reduced agglomeration between modified GOs as well as better interaction of hydrophilic-coated GOs with polymer membrane. Compared to the pure water flux of the membrane incorporated with unmodified GO, the membrane incorporated with DEAEMA-GO achieve approximately 85% higher value with oil removal rate remained almost unchanged (98.94% rejection).     

Effect of surface modification of graphite oxide on the morphological,thermal, and mechanical properties of polyurea/graphite oxide composites

Three surface modifiers, namely, aminopolyether (D2000), phenyl isocyanate, and poly(ethylene glycol) (PEG800), which have different affinities to the hard and soft segments in polyurea, were used to synthesize functionalized graphite oxides (GO). The PEG800‐modified (PEG800‐GO) and phenyl isocyanate‐modified (i‐GO) GOs were highly exfoliated and dispersed in DMF, whereas the D2000‐modified GO (D2000‐GO) produced some precipitates. Polyurea/GO composites were prepared using a solution‐blending method, in which functionalized GO platelet suspensions in dimethyl formamide were used. Results show that PEG800‐GO and i‐GO are uniformly dispersed throughout the polymer matrix on a nanoscale, whereas D2000‐GO forms visible aggregates. The well‐dispersed GO platelets improved the thermal stability and mechanical properties of polyurea. PEG800‐GO, which has a strong affinity for the soft segments, shows a more significant reinforcing effect. At 2.0 wt % GO loading, the tensile strength of polyurea was enhanced by ～75%. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39775.     

Size effects of graphene oxide on mixed matrix membranes for CO2 separation

Graphene oxide (GO)‐polyether block amide (PEBA) mixed matrix membranes were fabricated and the effects of GO lateral size on membranes morphologies, microstructures, physicochemical properties, and gas separation performances were systematically investigated. By varying the GO lateral sizes (100–200 nm, 1–2 μm, and 5–10 μm), the polymer chains mobility, as well as the length of the gas channels could be effectively manipulated. Among the as‐prepared membranes, a GO‐PEBA mixed matrix membrane (GO‐M‐PEBA) containing 0.1 wt % medium‐lateral sized (1–2 μm) GO sheets showed the highest CO₂ permeation performance (CO₂ permeability of 110 Barrer and CO₂/N₂ mixed gas selectivity of 80), which transcends the Robeson upper bound. Also, this GO‐PEBA mixed matrix membrane exhibited high stability during long‐term operation testing. Optimized by GO lateral size, the developed GO‐PEBA mixed matrix membrane shows promising potential for industrial implementation of efficient CO₂ capture. © 2016 American Institute of Chemical Engineers AIChE J, 62: 2843–2852, 2016     

Effect of flake size on thermal properties of graphene oxide/poly(methyl methacrylate) composites prepared via in situ polymerization

The effect of graphene oxide (GO) flake size on thermal properties of GO/poly(methyl methacrylate) (GO/PMMA) composites prepared via in situ polymerization was investigated. Two styles of GO sheets were synthesized from different sizes of graphite powders by modified Hummers' method and GO/PMMA composites with GO of different sizes were prepared via in situ polymerization. Transmission electron microscopy verified that GO sheets produced from large graphite powders was obviously larger than that from small graphite powders. The similar number of layers and disorder degree of two types of GO sheets were proved by X‐ray diffraction and Raman, respectively. X‐ray diffraction and scanning electron microscopy results of GO/composites proved the homogenous dispersion of both two types of GO sheets in polymer matrix. Dynamic mechanical analysis and thermogravimetric analysis results showed that large GO sheets exhibit better improvement than small GO sheets in thermal properties of the composites. Compared with neat PMMA, the glass transition temperature and decomposition temperature of the composites with large GO sheets (0.20 wt %) were increased by 15.9 and 25.9 °C, respectively. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46290.