Comparison Properties of Natural Rubber (SMR L)/Ethylene Vinyl Acetate (EVA) Copolymer Blends and Epoxidized Natural Rubber (ENR-50)/Ethylene Vinyl Acetate (EVA) Copolymer Blends

Mixing torque, morphology, tensile properties and swelling studies of natural rubber/ethylene vinyl acetate copolymer blends were studied. Two series of unvulcanized blends, natural rubber/ethylene vinyl acetate (SMRL/EVA) copolymer blend and epoxidized natural rubber (50% epoxidation)/ethylene vinyl acetate (ENR-50/EVA) copolymer blend were prepared. Blends were prepared using a laboratory internal mixer, Haake Rheomix polydrive with rotor speed of 50 rpm at 120°C. Results indicated that mixing torque value and stabilization torque value in ENR-50 blends are lower than SMRL blends. The process efficiency of ENR-50/EVA blends is better due to less viscous nature of the blend compared to SMRL/EVA blends as indicated in stabilization torque graph. Tensile properties like tensile strength, M100 (modulus at 100% elongation) and E _b (elongation at break) increase with increasing EVA fraction in the blend. At the similar blend composition, ENR-50 blend shows better tensile properties than SMRL blends. In oil resistance test, swelling percentage increased with immersion time and rubber composition. At a similar immersion time, ENR-50 blends exhibit better oil resistance compared to SMRL blends. Scanning electron microscopy (SEM) of tensile fractured surface indicated that EVA/ENR-50 blends need higher energy to cause catastrophic failure compared to EVA/SMRL blends. In etched cryogenically fractured surface, size and distribution of holes due to extraction of rubber phase by methyl ethyl ketone (MEK) were studied and holes became bigger as rubber composition increased due to coalescence of rubber particle.     

Preparation and Characterization of Ethylene Vinyl Acetate (EVA)/Natural Rubber (SMR L)/Organoclay Nanocomposites: Effect of Blending Sequences and Organoclay Loading

Ethylene vinyl acetate (EVA)/natural rubber (SMR L)/organoclay thermoplastic elastomer nanocomposites were melt compounded in an internal mixer, Haake Rheometer, at 120°C and 50 rpm rotor speed. In this paper, we demonstrate the effect of different blending sequences and organoclay loading from 2 to 10 phr (parts per hundred resins) on the tensile properties, morphology, thermal degradation, flammability, and water absorption behavior of EVA/SMR L/organoclay nanocomposites. EVA/SMR L/organoclay TPE nanocomposites were prepared by three different blending sequences, and each exhibited different tensile properties. Results indicated that the presence of organoclay increases the tensile properties, resistance toward thermal degradation, resistance to water permeation, and flame retardancy for all the nanocomposites prepared via different blending sequences. However, the optimum results for all the properties studied were achieved when EVA was blended with organoclay first and SMR L was incorporated later into the blend. The optimum organoclay loading was achieved at 2 phr. Results from scanning electron microscopy (SEM) and X-ray diffraction (XRD) studies showed that at 2 phr organoclay loading, nanostructures of individual silicate layers were achieved, whereas at 8 phr organoclay loading, agglomeration was observed. Flammability of the nanocomposites decreased when the organoclay loading increased.     

Properties of Polypropylene (PP)/Ethylene-Propylene Diene Terpolymer (EPDM)/Natural Rubber (NR) Vulcanized Blends: The Effect of N,N-m-Phenylenebismaleimide (HVA-2) Addition

This paper discusses process development, tensile properties, morphology, oil resistance, gel content, and thermal properties of polypropylene (PP)/ethylene-propylene diene terpolymer (EPDM)/natural rubber (NR) vulcanized blends with the addition of N,N-m-phenylenebismaleimide (HVA-2) as a compatibilizer. Blends were prepared in several blend ratios in a Haake Polydrive with temperature and rotor speed of 180°C and 50 rpm, respectively. Results indicated that the combination of dicumyl peroxide (Dicup) with HVA-2 shows high torque development and stabilization torque as compared to the blend with Dicup vulcanization alone. In terms of tensile properties, the combination of Dicup with HVA-2 shows higher tensile strength, tensile modulus (M₁₀₀), elongation at break, oil resistance, and gel content in all blend ratios compared to similar vulcanized blends with Dicup without HVA-2 addition. Scanning electron microscope (SEM) micrographs of the blends support that the cross-linking and compatibilization occur during the process of the vulcanized blend containing HVA-2. In the case of crystallinity of the blends, the addition of HVA-2 in Dicup vulcanized blend revealed a tendency for the percentage of crystallinity (Xc) to decrease. The addition of HVA-2 in Dicup vulcanization also produced blends with good thermal stability dealing with the so-called coagent bridge formation.     

Rheological and mechanical properties of compatibilized polystyrene/ethylene vinyl acetate blends

In this study, a blend of polystyrene (PS)/ethylene vinyl acetate (EVA) (PS/EVA, 90 : 10 wt %) was compatibilized with three different block copolymers, in which their end blocks were compatible with either styrene or EVA. The compatibilized blends with different compositions were prepared using a twin‐screw extruder and injection molded into the required test specimens. Mechanical properties of the blends, such as tensile properties and Charpy impact strength, morphology of tensile fractured surfaces, rheological properties, and thermal properties, were investigated. The results show that the interaction between the dispersed and continuous phase can be improved by the addition of a compatibilizer. Appreciable improvement in the impact strength of the blend with 15 wt % of compatibilizer C (polystyrene‐block‐polybutadiene) was observed. Its mechanical properties are comparable to those of the commercial high‐impact polystyrene, STYRON 470. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2071–2082, 2004     

Thermoplastic Elastomer Composites of Palm Ash-Filled Ethylene Vinyl Acetate/Natural Rubber Blends: Effects of Palm Ash Loading and Size

Thermoplastic elastomer composites of ethylene vinyl acetate (EVA)/natural rubber (NR) blends filled with palm ash were prepared by melt-mixing using a Haake Rheomix Polydrive R600/610 at 120°C with rotor speed of 50 rpm for 10 minutes. Increase in palm ash loading in composites resulted in increase the value of stabilization toque, Young's modulus and swelling resistance of the composites, but decreased the tensile strength and elongation at break. Scanning electron microscope micrographs revealed that higher filler loading resulted in agglomeration of palm ash in the composites. When smaller particle size of palm ash was used, further improvement in tensile strength, elongation at break, swelling resistance and stabilization torque value were observed.     

The role of nanofillers on (natural rubber)/(ethylene vinyl acetate)/clay nanocomposite in blending and foaming

Nanocomposite foams were fabricated from 60/40 wt% ethylene vinyl acetate (EVA)/natural rubber (NR) blends by using azodicarbonamide as a blowing agent. Two different nanofillers (sodium montmorillonite and organoclay) were employed to study their effects on foam properties. The results were also compared with conventional (china clay)‐filled foams. Transmission electron microscopy, X‐ray diffraction, scanning electron microscopy, and three‐dimensional Microfocus X‐ray computed tomography scanning analysis were performed to characterize the EVA/NR blend morphology and foam structures. The results revealed that the nanofiller acted as a blend compatibilizer. Sodium montmorillonite was more effective in compatibilization, generating better phase‐separated EVA/NR blend morphology and improving foam structure. Higher filler loading increased the specific tensile strength of rubber foams. The rubber nanocomposite foam showed superior specific tensile strength to the conventional rubber composite foam. The elastic recovery and compressive strength of the nanocomposite foams decreased with increasing filler content, whereas the opposite trend was observed for the conventional composite foams with china clay. The thermal conductivity measurement indicated that the nanofiller had better beneficial effect on thermal insulation over china clay filler. From the present study, the nanofillers played an important role in obtaining better blend morphology as compatibilizer, rather than the nucleating agent and the nanofiller content of 5 phr (parts by weight per hundred parts of rubber) was recommended for the production of EVA/NR nanocomposite foams. J. VINYL ADDIT. TECHNOL., 21:134–146, 2015. © 2014 Society of Plastics Engineers     

Electron Beam Irradiation of EVA/ENR Blend

The effect of irradiation on a 50/50 ethylene vinyl acetate/epoxidized natural rubber blend was studied. The 50/50 ethylene vinyl acetate/epoxidized natural rubber blend was prepared by mixing in a Brabender Plasticoder at 120°C. The blend was then irradiated by using a 3.0 MeV electron beam machine at doses ranging from 20 to 100 kGy in air and room temperature. The dynamic mechanical properties, tensile properties, hardness, and gel fractions of the blends were measured. It was found that the tensile strength, modulus, and hardness of the blend increased with irradiation with a concomitant decline in elongation at break. Results on the gel fraction revealed that under the irradiation conditions employed, the EVA/ENR blend crosslinked by electron beam irradiation. The addition of TMPTA and Surlyn ionomer was found to be effective in increasing the degree of crosslinking.     

Mechanical and sorption properties of poly(ethylene-co-vinyl acetate)(EVA) compatibilized acrylonitrile butadiene rubber/natural rubber blend systems

Poly (ethylene-co-vinyl acetate) (EVA) has been used as a compatibilizer for heterogeneous natural rubber/acrylonitrile butadiene rubber (NR/NBR) blends. NR/NBR (50/50) blends were compatibilized with varying amounts, from 0 to 10 parts per hundred rubber (phr), of EVA. The compatibility of the blend components in presence of EVA has been evaluated in terms of mechanical and sorption characteristics. The mechanical properties were found to be improved by the addition of EVA upto 6 phr. The solvent resistance of the compatibilized samples has been observed to be higher compared to the uncompatibilized blends; attributed to the increased interfacial adhesion between the blend components. DSC studies showed a shift of glass transition temperatures of the blend components towards higher temperatures indicating increased rigidity of the matrix in presence of EVA.     

Ethylene vinyl acetate as compatibilizer on cure characteristics and mechanical properties of (natural rubber)/(Recycled acrylonitrile‐butadiene rubber) blends

Ethylene vinyl acetate (EVA) has been used as a compatibilizer for (natural rubber)/(recycled acrylonitrile‐butadiene rubber) (NR/NBRr) blends, vulcanized by sulfur. EVA offers excellent heat, ozone, and weather resistance, whereas the vinyl acetate groups provide oil resistance to the blend. It exhibits good tear resistance and may be crosslinked. However, EVA exhibits poor low‐temperature flexibility. NBR gloves have excellent resistance to punctures, tears, and many types of chemicals, while NR has good physical and mechanical properties. NR/NBRr blends were prepared with various compositions with the EVA content fixed. Tensile properties, hardness, and swelling behavior tests were performed to determine the compatibility of NR/NBRr blends in the presence of EVA. Results indicated that incorporation of EVA into NR/NBRr blends improved tensile strength, modulus, and elongation at break compared with NR/NBRr blends without EVA. The improvement in hardness and reduction in resilience on compatibilization are due to an increase in crosslink density, which gives NR/NBRr blends better swelling resistance. Scanning electron microscopy of the fracture surfaces indicates that, with the addition of EVA in NR/NBRr blends, better adhesion between NR and NBRr was obtained, thus improving the compatibility of NR/NBRr blends. J. VINYL ADDIT. TECHNOL., 23:135–141, 2017. © 2015 Society of Plastics Engineers     

The effect of trimethylol propane tetraacrylate (TMPTA) and organoclay loading on the properties of electron beam irradiated ethylene vinyl acetate (EVA)/natural rubber (SMR L)/organoclay nanocomposites

Ethylene vinyl acetate (EVA)/natural rubber (SMR L)/organoclay nanocomposites were prepared by melt blending technique with 0–10 phr organoclay loading and 3 phr TMPTA. Electron beam initiated crosslinking on these samples was carried out using a 3.0 MeV electron beam machine with doses ranging from 50 to 200 kGy. XRD results proved that dispersion of organoclay in the nanocomposites was slightly improved by irradiation with TMPTA. This was further supported by transmission electron microscopy images, where the nanoscale dispersion of organoclay was more homogenous throughout the irradiated polymer matrix compared to nonirradiated samples. TMPTA also increased the gel fraction yield, tensile properties and thermal stability of the irradiated neat EVA/SMR L and its nanocomposites. TMPTA was found to act as a crosslink initiator, which promotes crosslink bridges via free radical mechanism in EVA/SMR L matrix. SEM observation shows that the fracture behavior of the irradiated neat EVA/SMR L and its nanocomposites with TMPTA is significantly different compared to the fracture behavior of the nonirradiated neat EVA/SMR L. The distinct failure surface structure formed in the irradiated samples with TMPTA explains the overall higher value of tensile properties. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Natural rubber/poly(ethylene‐co‐vinyl acetate)‐blend‐based nanocomposites

Natural rubber (NR)/poly(ethylene‐co‐vinyl acetate) (EVA) blend–clay nanocomposites were prepared and characterized. The blend nanocomposites were prepared through the melt mixing of NR/EVA in a ratio of 40/60 with various amounts of organoclay with an internal mixer followed by compression molding. X‐ray diffraction patterns revealed that the nanocomposites formed were intercalated. The formation of the intercalated nanocomposites was also indicated by transmission electron microscopy. Scanning electron microscopy, used to study the fractured surface morphology, showed that the distribution of the organoclay in the polymer matrix was homogeneous. The tensile modulus of the nanocomposites increased with an increase in the organoclay content. However, an increase in the organoclay content up to 5 phr did not affect the tensile strength, but the organoclay reduced this property when it was increased further. This study also indicated that a low silicate content dispersed in the blend matrix was capable of increasing the storage modulus of the material. The addition of the organoclay also increased the decomposition temperature of the NR/EVA blends. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 353–362, 2006     

Characterization of epoxidized natural rubber/ethylene vinyl acetate (ENR‐50/EVA) blend: Effect of blend ratio

Epoxidized natural rubber/Ethylene vinyl acetate copolymer (ENR‐50/EVA) blends with different ratios were prepared by using a Haake internal mixer. The effect of the blend ratio on the processing, tensile properties (such as tensile strength, elongation at break, Young's modulus and stress–strain behavior), morphology, dynamic mechanical properties, and thermal properties has been investigated. The tensile properties increase with the increase of EVA content, whereas the stabilization torque increases with the increase of ENR‐50 content in the blend. In 40:60 and 50:50 blend of ENR‐50/EVA, both the phases exist as continuous phases, producing a co‐continuous morphology. At these blend ratio, the drastic change in properties were noted, indicating that the phase inversion occurs. The results on dynamic mechanical properties revealed that the blends are compatible. Blending of ENR‐50 and EVA lead to the improvement in thermal stability and 50:50 blend ratios is the most stable blend. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1504–1515, 2006     

Physical properties of ethylene vinyl acetate copolymer (EVA)/natural rubber (NR) blend based foam

In this study an attempt was made to improve the rebound resilience and to decrease the density of ethylene‐vinyl acetate copolymer (EVA) foam. For this purpose, EVA was blended with natural rubber (NR), and EVA/NR blends were foamed at 155°C, 160°C, and 165°C. To investigate the correlation between crosslinking behavior and physical properties of foams, crosslinking behavior of EVA/NR blends was monitored. The physical properties of the foams were then measured as a function of foaming temperatures and blend compositions: 165°C was found to be the optimal temperature for a crosslinking of EVA/NR foam. As a result, the density of EVA/NR blend foamed at 165°C was found to be the lowest. EVA/NR (90/10) blend, foamed at 165°C, showed lower density, better rebound resilience, and greater tear strength than EVA foam. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2212–2216, 2004     

Double‐yielding behavior in injection‐molded polycarbonate/high‐density polyethylene/ethylene–vinyl acetate copolymer blends

A uniaxial tensile test was performed for polycarbonate (PC)/high‐density polyethylene (HDPE)/ethylene–vinyl acetate copolymer (EVA) blends with a fixed EVA content but various PC contents. The double‐yielding phenomenon and its composition dependence, as observed in the PC/HDPE blend, were again detected. EVA did not serve as a successful compatibilizer of PC and HDPE in the PC/HDPE/EVA blend. The incorporation of EVA resulted in a larger size and a more irregular shape of the PC fibers, as indicated in the scanning electron microscope observations; this, consequently, produced a higher serious stress concentration in the blend. This more complicated and instable morphology produced different double‐yielding behaviors in the PC/HDPE/EVA blends compared with the binary one. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of different curing systems on heat shrinkability and mechanical properties of ethylene vinyl acetate/epoxidized natural rubber blends

Ethylene vinyl acetate (EVA)/epoxidized natural rubber (ENR) blends containing 10 and 30 wt % ENR were prepared by using an internal mixer. Five different types of curing systems were employed: dicumyl peroxide (DCP), sulfur (S), phenolic resin (Ph), DCP + S, and DCP + Ph. DCP could crosslink with both EVA and ENR while S and Ph were curing agents for ENR. The DCP system provided the lowest tensile properties and tear strength because of low crosslinking in ENR phase. Addition of sulfur or phenolic resin increased the mechanical properties due to a better vulcanization of the rubber phase. The mechanical properties of the blends decreased with increasing ENR content. The rubber particle size in the blends containing 30% ENR played a more important role in the mechanical properties than the blends containing 10% ENR. ENR particle size did not affect heat shrinkability of EVA and a well vulcanized rubber phase was not required for high heat shrinkage. Furthermore, heat shrinkage of the blends slightly changed as the ENR content increased for all curing systems. With regard to the mechanical properties and heat shrinkability, the most appropriate curing system was DCP + Ph and in the case the 10 wt % ENR content produced a more favorable blend. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effects of Dynamic Vulcanization and Acrylic Acid on Properties of Recycled Poly(vinyl chloride)/Acrylonitrile Butadiene Rubber (PVCr/NBR) Blends

Effects of dynamic vulcanization and acrylic acid (AAc) on processability, mechanical properties, swelling behavior, morphology, and thermal stability of recycled poly(vinyl chloride)/acrylonitrile butadiene rubber (PVCr/NBR) blends were investigated. Blends were prepared in a Haake Rheomix at a temperature of 150°C and a rotor speed of 50 rpm. Recycled poly(vinyl chloride)/acrylonitrile butadiene rubber (PVCr/NBR) blends were also prepared as comparison. It was found that the dynamic vulcanization and the addition of acrylic acid improved the stabilization torque, mechanical energy, stress at peak, stress at 100% elongation (M₁₀₀), swelling resistance, and thermal stability but decreased the elongation at break of the blends. The introduction of a cross-link into the elastomer phase and better compatibility between PVCr and NBR are responsible for the enhancement of thermal stability and mechanical properties of dynamically vulcanized PVCr/NBR + AAc as evidence from the scanning electron microscopy (SEM) of the tensile fracture surfaces and infrared spectroscopy study of the dynamically vulcanized of PVCr/NBR + AAc shows.     

Cure characteristics,morphology, mechanical properties,and aging characteristics of silicone rubber/ethylene vinyl acetate blends

Silicone rubber/ethylene vinyl acetate (SR/EVA) rubber mixes with different ratios were prepared by using dicumyl peroxide (DCP) and benzoyl peroxide (BP) as curing agents. The vulcanization characteristics such as cure kinetics, activation energy, and cure rate of the blends were analyzed. The effects of blend ratio and curing agents on the mechanical properties such as stress–strain behavior, tensile strength, elongation at break, tear strength, relative volume loss, hardness, flex crack resistance, and density of the cured blends have been investigated. Almost all the mechanical properties have been found to be increased with increase in EVA content in the blends particularly in DCP‐cured systems. The increment in mechanical properties of the blends with higher EVA content has been explained in terms of the morphology of the blends, attested by scanning electron micrographs. Attempts have been made to compare the experimental results, from the evaluation of mechanical properties, with relevant theoretical models. The aging characteristics of the cured blends were also investigated and found that both the DCP‐ and BP‐cured blends have excellent water and thermal resistance. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1069–1082, 2006     

Synthesis of silane‐grafted ethylene vinyl acetate copolymer and its application to compatibilize the blend of ethylene‐propylene‐diene copolymer and silicone rubber

Vinyltrimethoxysilane‐grafted ethylene vinyl acetate copolymer (EVA‐g‐VTMS) was synthesized and applied to compatibilize ethylene‐propylene‐diene copolymer (EPDM)/methyl vinyl silicone rubber (MVQ) blends. The silane‐grafting was successfully proved by differential scanning calorimetry, FTIR spectroscopy and XPS spectroscopy. The additive amount of the compatibilizer (EVA‐g‐VTMS) was optimized to be 10 phr (parts per hundred of rubber in weight) based on analysis of scanning electron microscopy, mechanical properties, aging properties, dynamic mechanical properties, rheological properties and thermal properties. Compared with the blend without EVA‐g‐VTMS, results show that the blend with 10 phr of EVA‐g‐VTMS exhibits the finest morphology. Tensile strength, elongation at break, modulus at 100% elongation, tear strength and TE index increase by 82.5%, 16.9%, 60.0%, 40.9%, and 41.9%, respectively. Dynamic mechanical analysis reveals storage modulus increase and glass transition temperatures of EPDM and MVQ move closer to each other. Rheological analysis shows a decrease in complex modulus and complex viscosity, and the processibility of the blend was improved. Furthermore, thermogravimetric analysis shows enhancement of thermal stability. POLYM. ENG. SCI., 2017. © 2017 Society of Plastics Engineers     

Mechanical properties and blend compatibility of natural rubber –chlorosulfonated polyethylene blends

Natural rubber (NR) was blended with chlorosulfonated polyethylene (CSM) with various formulation and blend ratios (NR/CSM: 80/20 –20/80, wt/wt). Rubber blends were prepared by using a two‐roll mill and vulcanized in a compression mold to obtain the 2 mm‐thick sheets. Tensile properties, tear resistance, thermal aging resistance, ozone resistance, and oil resistance were determined according to ASTM. Compatible NR/CSM blends are derived from certain blends containing 20–30% CSM without adding any compatibilizing agent. Tensile and tear strength of NR‐rich blends for certain formulations show positive deviation from the rule of mixture. Thermal aging resistance depends on formulation and blend ratio, while ozone and oil resistance of the blends increase with CSM content. Homogenizing agents used were Stuktol®60NS and Epoxyprene®25. Stuktol®60NS tends to decrease the mechanical properties of the blends and shows no significant effect on blend morphology. Addition of 5–10 phr of epoxidized natural rubber (ENR, Epoxyprene® 25) increases tensile strength, thermal aging resistance, and ozone resistance of the blends. It is found that ENR acts as a compatibilizer of the NR/CSM blends by decreasing both CSM particle size diameter and α transition temperature of CSM. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 127–140, 2006     

Effect of rubber content on mechanical properties and heat shrinkage of ethylene vinyl acetate copolymer blended with epoxidized natural rubber

Ethylene vinyl acetate (EVA, 18 mol % vinyl acetate) and epoxidized natural rubber (ENR, 50 mol % epoxidation) were blended in an internal mixer and compared to EVA. Dicumyl peroxide (DCP) was used as a curing agent. The blends consisted of 10–50 wt % of ENR and were compared with crosslinked EVA in terms of heat shrinkage, mechanical properties, and degree of crystallinity. It is found that the blends showed a decrease in mechanical properties with increasing ENR content because DCP was not a good vulcanizing agent of ENR. The addition of ENR did not affect heat shrinkability of EVA. The maximum heat shrinkage obtained was 80% for EVA and the blends. ENR did not affect thermal properties of EVA investigated by the differential scanning calorimetry. The X‐ray diffractometry showed discrepancy in degree of crystallinity before and after specimen stretching and after heat shrinking. It is believed that ENR particles decreased molecular orientation of EVA resulting in a decrease in degree of crystallinity but the remained orientation was sufficient for heat shrinking. The blend showed better extrudability than EVA after increasing take‐up speed. Therefore, the extruded tube prepared from the blend provided higher heat shrinkage than EVA tube. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009