共查询到19条相似文献,搜索用时 578 毫秒
1.
采用实验方法,对旋进漩涡流量计-锥形阀组合式流量调节装置的流量测量与调节特性,进行了研究.首先在有无锥形阀情况下,对旋进漩涡流量计的输出特性进行了测试,发现无论上游有无锥形阀,所测得压力信号的脉动频率与流量之间均呈现良好的线性关系,且同一流量时,锥形阀的存在引起的压力脉动频率变化小于5%.测量结果说明,在这种组合式的流量调节装置中,旋进漩涡流量计能够正常工作.装置的流量调节特性测试中,在进口压力为0.11~0.23MPa、阀芯行程0~8mm的范围内,测量了流量的变化情况.结果发现,进口压力不变时,流量随着开度的增大而增大,流量与开度之间呈线性关系;当进口压力增大时,通过的流量也增大;反之亦然. 相似文献
2.
3.
4.
水压传动技术应用于深海环境可以直接从海洋中吸水加压,高压水作功之后可以直接排入海洋,不需要水箱和回水管道,大大简化了系统,具有独特的优势。然而,在深海作业时,液压元件的工况同陆地相比有较大的差异,海深压力相当于在元件出口加了一个背压。文中用背压来模拟海水压力,对以水作介质时背压对提升阀口流量特性的影响进行了实验研究。研究结果表明,背压使得流量饱和更容易发生;有背压时的流量系数比没有背压时的流量系数大;当阀芯和阀座有叠合时,背压对阀口流量特性的影响比阀芯和阀座没有叠合时的影响大。 相似文献
5.
6.
7.
正一、封闭管道流量测量(一)差压式原理的流量计1.差压式流量计差压式流量计由节流装置(或动压测定装置)、差压讯号管路和差压计3部分组成。基本原理是充满管道的流体流经管道内的节流装置,流束将在节流件处形成局部收缩,从而使流速增加,静压力降低,于是在节流件前后产生静压力差。流体的流速愈大,在节流件前后产生的差压愈大,所以可通过测量差压衡量流体流过节流装置时的流量大小,这种测量方法以能量守恒定律和流动连续性方程为基础。差压式流量计历史悠久,经长期实践积累了可靠的试验数据和运行经 相似文献
8.
调节阀的流量特性校正 总被引:1,自引:0,他引:1
由于在控制系统设计时一般都假定调节阀前后压差为常数,而实际上压差总会随着阀的开度变化而变化,这种误差会导致调节阀流量特性的畸变,对系统的控制性能有一定的影响。通过设计调节阀的流量特性校正装置,可以较好地克服调节阀的畸变,使调节阀的工作特性维持在比较理想的工作状态。实验证明这种校正对阀的工作特性改善非常明显。 相似文献
9.
环形管流量计不同测点位置的信号分析及误差估计 总被引:1,自引:2,他引:1
设计了一个多圈环形管流量计,在环形管不同位置上布置差压测点,测量同一流量下各测点位置信号差压的不同和变化趋势.结果表明:环形管流量计的差压输出随着测点位置的不同有很大的差异,流量系数也有不同的变化趋势.然而,经修正后,测量精度可控制在±1%以内. 相似文献
10.
11.
通过试验研究R22流过节流短管的流动特性,分析影响节流短管中制冷剂流量的几个重要因素;上游压力、下游压力、上游过冷度和短管直径。试验结果表明,当节流短管的下游压力小于上游温度所对应的饱和压力时,制冷剂出现壅塞现象,此时制冷剂流量不再受下游压力变化的影响;上游压力、上游过冷度、短管直径对制冷剂流量的影响较大。 相似文献
12.
13.
针对煤化工专用控制阀易磨损失效的问题,提出基于数值模拟的阀内流场分析方法.今基于可实现k-ε(Realizable k-ε)双方程湍流模型,通过有限元分析法(finite element analysis,FEA),对控制阀的多相流流场中的湍流特征进行数值模拟研究,得到湍流流场内的压力、速度的分布,并结合Preston磨削经验公式,得到控制阀内最易磨损的区域,从而为后续控制阀的结构优化设计及表面强化打下了基础. 相似文献
14.
针对目前电子膨胀阀(EXV)测试设备的自动化程度低、测试结果不准确等缺点,遵照JB/T 10386-2002的测试方法,设计了一套适用于各类电子膨胀阀的流量特性测试系统.该装置采用了以单片机为核心的控制方案,并且开发了专用的电子膨胀阀驱动器.最后通过实验验证,该测试装置很好地实现了对电子膨胀阀流量特性的测试以及合格与否的初步判断,流量测试精度小于1.5%FS,测量参数指标达到技术要求. 相似文献
15.
16.
In a direct coal liquefaction unit, pressure relief valves locate on the pipeline between the atmospheric and vacuum towers. Failures of the valve components occur frequently owing to the harsh operation conditions. A combined numerical-experiment investigation on the failures of valves is conducted in this paper. The variation of relative erosion rates of WC–Co coating with impact angles, the function of relative particle velocity, and the distribution of particle diameters are obtained from the high-temperature erosion experiments. Furthermore, the erosion mechanism of WC–Co coating under large impact angles is clarified. In the numerical simulation, the evaporation–condensation, particle motion, erosion, and the modified RNG k-ε turbulence models are used to analyze the phase transition and particle erosion in the valves. Results showed that: due to the high pressure drop and convergent–divergent structure of angle valve, the coal-oil slurry flashes as it enters into the valves. The evaporation of liquid oil produces a large amount of vapor oil, and results in a rapid increase in flow velocity. High concentration solid particles, driven by the high-speed stream, tend to erode the inner surface of valves. Severe erosion can be found in the spool of angle valve, downstream bushings at the angle valve and ball valve. The calculation results agree well with actual failure morphologies, verifies the accuracy of the present prediction method. 相似文献
17.
一种真空状态下的气体流量测量新方法 总被引:1,自引:0,他引:1
当空气绝对压力小于40 kPa时,目前尚无简便有效的气流质量流量测量手段,为此本文设计了一套新颖的流量标定装置,并提出一种了流量测量方法。在流量调节过程中,调节阀必不可少。真空状态下,流经调节阀的流量几乎完全由阀前、后压力、气流温度四个变量决定。本文由流量标定装置获取有效的数据样本,基于多元非线性回归方法建立了流量与四者的关系表达式。一定范围内只要测定四个变量,则能直接计算出相应流量。实验结果表明计算值与实测流量偏差小于3.0%。 相似文献
18.
差压气密性检测仪设计与实现 总被引:4,自引:3,他引:1
设计了基于差压法原理的以ARM处理器为控制核心的通用型气密性检测仪.该仪器系统通过气控阀控制气路对工件的充放气过程,并利用高精度差压传感器获得由气体泄露产生的差压值,人机交互界面采用触摸屏模块.结果表明,该检测仪方便快捷、测试精度高、稳定性好. 相似文献
19.
Jun-Hyeung Kim James E. Braun Eckhard A. Groll 《International Journal of Refrigeration》2009,32(6):1271-1282
A hybrid method for optimizing refrigerant distribution in evaporators is presented that involves the use of small balancing valves in each circuit along with a primary expansion device to control the overall superheat from the evaporator. The flow balancing valves could be located upstream or downstream of the evaporator. This paper presents the results of a study to investigate the benefits of this hybrid scheme for both upstream and downstream flow balancing for the case of air flow mal-distribution. In order to perform this investigation, a simulation model was developed to consider evaporator flow mal-distributions for a 10.55 kW residential R410A heat pump and then validated through comparisons of predicted results with measurements. Simulation results show that there are significant benefits in controlling the superheat of each circuit of evaporators through the hybrid–individual superheat control method. Furthermore, the upstream refrigerant flow control consistently outperforms the downstream refrigerant flow control, and recovers most of the loss in cooling capacity and COP due to non-uniform air flow distribution. 相似文献