Poly(hydroxybutyrate)/poly(butylene succinate) blends: miscibility and nonisothermal crystallization

Four blends of poly(hydroxybutyrate) (PHB) and poly(butylene succinate) (PBSU), both biodegradable semicrystalline polyesters, were prepared with the ratio of PHB/PBSU ranging from 80/20 to 20/80 by co-dissolving the two polyesters in N,N-dimethylformamide and casting the mixture. Differential scanning calorimetry (DSC) and optical microscopy (OM) were used to probe the miscibility of PHB/PBSU blends. Experimental results indicated that PHB showed some limited miscibility with PBSU for PHB/PBSU 20/80 blend as evidenced by the small change in the glass transition temperature and the depression of the equilibrium melting point temperature of the high melting point component PHB. However, PHB showed immiscibility with PBSU for the other three blends as shown by the existence of unchanged composition independent glass transition temperature and the biphasic melt. Nonisothermal crystallization of PHB/PBSU blends was investigated by DSC using various cooling rates from 2.5 to 10 °C/min. During the nonisothermal crystallization, despite the cooling rates used two crystallization peak temperatures were found for PHB/PBSU 40/60 and 60/40 blends, corresponding to the crystallization of PHB and PBSU, respectively, whereas only one crystallization peak temperature was observed for PHB/PBSU 80/20 and 20/80 blends. However, it was found that after the nonisothermal crystallization the crystals of PHB and PBSU actually co-existed in PHB/PBSU 80/20 and 20/80 blends from the two melting endotherms observed in the subsequent DSC melting traces, corresponding to the melting of PHB and PBSU crystals, respectively. The subsequent melting behavior was also studied after the nonisothermal crystallization. In some cases, double melting behavior was found for both PHB and PBSU, which was influenced by the cooling rates used and the blend composition.     

Miscibility and crystallization in crystalline/crystalline blends of poly(butylene succinate)/poly(ethylene oxide)

Miscibility and crystallization behavior have been investigated in blends of poly(butylene succinate) (PBSU) and poly(ethylene oxide) (PEO), both semicrystalline polymers, by differential scanning calorimetry and optical microscopy. Experimental results indicate that PBSU is miscible with PEO as shown by the existence of single composition dependent glass transition temperature over the entire composition range. In addition, the polymer-polymer interaction parameter, obtained from the melting depression of the high-T_m component PBSU using the Flory-Huggins equation, is composition dependent, and its value is always negative. This indicates that PBSU/PEO blends are thermodynamically miscible in the melt. The morphological study of the isothermal crystallization at 95 °C (where only PBSU crystallized) showed the similar crystallization behavior as in amorphous/crystalline blends. Much more attention has been paid to the crystallization and morphology of the low-T_m component PEO, which was studied through both one-step and two-step crystallization. It was found that the crystallization of PEO was affected clearly by the presence of the crystals of PBSU formed through different crystallization processes. The two components crystallized sequentially not simultaneously when the blends were quenched from the melt directly to 50 °C (one-step crystallization), and the PEO spherulites crystallized within the matrix of the crystals of the preexisted PBSU phase. Crystallization at 95 °C followed by quenching to 50 °C (two-step crystallization) also showed the similar crystallization behavior as in one-step crystallization. However, the radial growth rate of the PEO spherulites was reduced significantly in two-step crystallization than in one-step crystallization.     

DSC and TMDSC study of melting behaviour of poly(butylene succinate) and poly(ethylene succinate)

The subsequent melting behaviour of poly(butylene succinate) (PBSU) and poly(ethylene succinate) (PES) was investigated using DSC and temperature modulated DSC (TMDSC) after they finished nonisothermal crystallization from the melt. PBSU exhibited two melting endotherms in the DSC traces upon heating to the melt, which was ascribed to the melting and recrystallization mechanism. However, one melting endotherm with one shoulder and one crystallization exotherm just prior to the melting endotherm were found for PES. The crystallization exotherm was ascribed to the recrystallization of the melt of the crystallites with low thermal stability, and the shoulder was considered to be the melting endotherm of the crystallites with high thermal stability. The final melting endotherm was ascribed to the melting of the crystallites formed through the reorganization of the crystallites with high thermal stability during the DSC heating process. TMDSC experiments gave the direct evidences to support the proposed models to explain the melting behaviour of PBSU and PES crystallized nonisothermally from the melt.     

Radiopaque iodinated poly(ester-urethane)s based on poly(butylene succinate): Retarded crystallization and dual recrystallization behaviour

A series of biodegradable radiopaque iodinated poly(ester-urethane)s (IPEUs) were synthesized by chain-extension of dihydroxylated poly(butylene succinate) (PBS–OH) and isophorone diisocyanate (IPDI) with iodinated bisphenol-A (IBPA). The effects of IBPA on the crystallization and melting behaviour of IPEUs were investigated by wide-angle X-ray diffraction (WAXD), polarized optical microscope (POM), differential scanning calorimetry (DSC), and temperature-modulated differential scanning calorimetry (TMDSC). WAXD results suggest that the PBS soft segments form only one crystal modification, and that the crystallinity of the samples decreases with increasing the amorphous hard segments. POM observation indicates that the ring-bands of spherulites disappear and then the spherulitic texture is disturbed with increasing the IBPA content. The analysis of isothermal crystallization kinetics shows that the crystallization of IPEUs is retarded by the introduction of IBPA chain extender with bulky pendent groups. In the DSC heating curves, at most four endothermic peaks were observed and their origins were examined. Two recrystallization exothermic peaks were observed for IPEUs in the nonreversible signals of TMDSC. The twice sequential melting–recrystallization–remelting model could be used to explain the multiple melting behaviour of IPEUs.     

Miscibility and crystallization behavior of biodegradable blends of two aliphatic polyesters. Poly(butylene succinate) and Poly(ε-caprolactone)

Poly(butylene succinate) (PBSU) and poly(ε-caprolactone) (PCL) blends, both biodegradable chemosynthetic semicrystalline polyesters, were prepared with the ratio of PBSU/PCL ranging from 80/20 to 20/80 by co-dissolving the two polyesters in chloroform and casting the mixture. The miscibility and crystallization behavior of PBSU/PCL blends were investigated by differential scanning calorimetry and optical microscopy. Experimental results indicated that PBSU was immiscible with PCL as evidenced by the composition independent glass transition temperature and the biphasic melt. However, during the crystallization from the melt at a given cooling rate, the crystallization peak temperature of PBSU in the blends decreased slightly with the increase of PCL, while that of PCL in the blends first increased and then decreased with the increase of PBSU. Moreover, both the crystallization peak temperature of PBSU and PCL shifted to the low temperature range with the increase of the cooling rate for a given blend composition. Double melting peaks or one main melting peak with a shoulder were found for both PBSU and PCL after the complete crystallization cooled from the melt, and were ascribed to the melting-recrystallization mechanism. It was found that the subsequent melting behavior of PBSU/PCL blends was influenced apparently by the blend composition and the cooling rate used.     

On the triple melting behaviour of poly(ethylene succinate)

The morphology of melt-crystallized poly(ethylene succinate) (PES) was investigated by optical microscopy and scanning electron microscopy, and the melting behaviour of PES was studied by differential scanning calorimetry (DSC). At low crystallization temperature imperfect crystals were formed which could melt and recrystallize during the DSC scan. Triple melting peaks were observed, and the melting behaviour was strongly dependent on crystallization time and scan rate. It was observed that crystallization at high temperature perfected the crystals (dominant and subsidiary lamellae in the spherulitic structure). Increasing the scan rate reduced the chance for reorganization. However, at high crystallization temperature two melting peaks were observed. The material formed was much more perfect, so that the melting process was not dominated by recrystallization. Accordingly, the cause of dual melting is the existence of two kinds of crystal perfection.     

Miscibility,melting, and crystallization behavior of poly(hydroxybutyrate) and poly(D,L‐lactic acid) blends

Melting behavior and crystal morphology of poly(3‐hydroxybutyrate)‐poly(D ,L ‐lactic acid) (PHB‐RPLA) blends with various compositions have been investigated by modulated temperature differential scanning calorimetry (mt‐DSC), polarized optical thermomicroscopy (POTM), modulated force thermomechanometry (mf‐TM), and small angle X‐ray scattering (SAXS). Thermal properties were investigated after fast cooling crystallization treatment. Multiple melting peak behavior was observed for all polymers. mt‐DSC data revealed that PHB‐RPLA blends undergo melting‐recrystallization‐remelting during heating, as evidenced by exothermic peaks in the nonreversing heat capacity. A decrease in degree of crystallinity due to significant melt‐recrystallization was observed for blends. PHB‐RPLA showed different crystal morphologies for various compositions. POTM results showed that the crystallization rates and sizes of spherulites were significantly reduced as RPLA content increased. mf‐TM results confirmed miscibility of these two polymers. SAXS data provided evidence of lamella thickness of blends, which increased with increasing RPLA content. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Study of the miscibility and crystallization behavior of poly(ethylene oxide)/poly(vinyl alcohol) blends

The miscibility and crystallization behavior of poly(ethylene oxide)/poly(vinyl alcohol) (PEO/PVA) blends were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and polarizing optical microscopy. Because the glass‐transition temperature of PVA was near the melting point of PEO crystalline, an uncommon DSC procedure was used to determine the glass‐transition temperature of the PVA‐rich phase. From the DSC and DMA results, two glass‐transition temperatures, which corresponded to the PEO‐rich phase and the PVA‐rich phase, were observed. It was an important criterion to indicate that a blend was immiscible. It was also found that the preparation method of samples influenced the morphology and crystallization behaviors of PEO/PVA blends. The domain size of the disperse phase (PVA‐rich) for the solution‐cast blends was much larger than that for the coprecipitated blends. The crystallinity, spherulitic morphology, and isothermal crystallization behavior of PEO in the solution‐cast blends were similar to those of the neat PEO. On the contrary, these properties in the coprecipitated blends were different from those of the neat PEO. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1562–1568, 2004     

Poly(butylene succinate)/poly(vinyl phenol) blends. Part 1. Miscibility and crystallization

Miscibility has been investigated in blends of poly(butylene succinate) (PBSU) and poly(vinyl phenol) (PVPh) by differential scanning calorimetry in this work. PBSU is miscible with PVPh as shown by the existence of single composition dependent glass transition temperature over the entire composition range. In addition, the polymer–polymer interaction parameter, obtained from the melting depression of PBSU using the Nishi–Wang equation, is composition dependent, and its value is always negative. This indicates that PBSU/PVPh blends are thermodynamically miscible in the melt. Preliminary morphology study of PBSU/PVPh blends was also studied by optical microscopy (OM). OM experiments show the spherulites of PBSU become larger with the PVPh content, indicative of a decrease in the nucleation density, and the coarseness of PBSU spherulites increases too with increasing the PVPh content in the blends.     

Miscibility and crystallization behaviour of biodegradable blends of two aliphatic polyesters. Poly(3-hydroxybutyrate-co-hydroxyvalerate) and poly(butylene succinate) blends

Blends of poly(3-hydroxybutyrate-co-hydroxyvalerate) (PHBV) and poly(butylene succinate) (PBSU), both biodegradable semicrystalline polyesters, were prepared with the ratio of PHBV/PBSU ranging from 80/20 to 20/80 by co-dissolving the two polyesters in chloroform and casting the mixture. Differential scanning calorimetry (DSC) and optical microscopy (OM) were used to study the miscibility and crystallization behaviour of PHBV/PBSU blends. Experimental results indicate that PHBV is immiscible with PBSU as shown by the almost unchanged glass transition temperature and the biphasic melt. Crystallization of PHBV/PBSU blends was studied by DSC using two-step crystallization and analyzed by the Avrami equation. The crystallization rate of PHBV decreases with the increase of PBSU in the blends while the crystallization mechanism does not change. In the case of the isothermal crystallization of PBSU, the crystallization mechanism does not change. The crystallization rate of PBSU in the blends is lower than that of neat PBSU; however, the change in the crystallization rate of PBSU was not so big in the blends. The different content of the PHBV in the blends does not make a significant difference in the crystallization rate of PBSU.     

Effect of blend composition on crystallization behavior of polyoxymethylene/poly(ethylene oxide) crystalline/crystalline blends

The influence of blend composition on crystallization behavior of a typical crystalline/crystalline blend, polyoxymethylene (POM)/poly(ethylene oxide) (PEO), during slow non-isothermal crystallization was investigated by polarized light microscope (PLM) connected with a THMS600 hot-stage, scanning electron microscope (SEM), differential scanning calorimetry (DSC) and X-ray diffraction (XRD). The experimental results indicated that with increasing PEO content in the blend, the crystallization temperature of POM of the blends reduced and the multiple crystalline morphologies or structures including two kinds of interfibrillar or interlamellar structures were produced. The melting point of each component decreased with raising the content of the other constituent due to the inclusion and entanglement between POM and PEO molecules. The shoulder melting peak of POM appeared in DSC heating traces of the PEO-rich blend because the stronger inclusion and entanglement induced the imperfect crystallization of POM.     

Crystallization kinetics and morphology of poly(butylene succinate)/poly(vinyl phenol) blend

Biodegradable crystalline poly(butylene succinate) (PBSU) can form miscible polymer blends with amorphous poly(vinyl phenol) (PVPh). The isothermal crystallization kinetics and morphology of neat and blended PBSU with PVPh were studied by differential scanning calorimetry (DSC), optical microscopy (OM), wide angle X-ray diffraction (WAXD), and small angle X-ray scattering (SAXS) in this work. The overall isothermal crystallization kinetics of neat and blended PBSU was studied with DSC in the crystallization temperature range of 80-88 °C and analyzed by applying the Avrami equation. It was found that blending with PVPh did not change the crystallization mechanism of PBSU, but reduced the crystallization rate compared with that of neat PBSU at the same crystallization temperature. The crystallization rate decreased with increasing crystallization temperature, while the crystallization mechanism did not change for both neat and blended PBSU irrespective of the crystallization temperature. The spherulitic morphology and growth were observed with hot stage OM in a wide crystallization temperature range of 75-100 °C. The spherulitic morphology of PBSU was influenced apparently by the crystallization temperature and the addition of PVPh. The linear spherulitic growth rate was measured and analyzed by the secondary nucleation theory. Through the Lauritzen-Hoffman equation, some parameters of neat and blended PBSU were derived and compared with each other including the nucleation parameter (K_g), the lateral surface free energy (σ), the end-surface free energy (σ_e), and the work of chain folding (q). Blending with PVPh decreased all the aforementioned parameters compared with those of neat PBSU; however, the decrease extent was limited. WAXD result showed that the crystal structure of PBSU was not modified after blending with PVPh. SAXS result showed that the long period of blended PBSU increased, possibly indicating that the amorphous PVPh might reside mainly in the interlamellar region of PBSU.     

Temperature modulated DSC and DSC studies on the origin of double melting peaks in poly(ether ether ketone)

Crystallization kinetics and melting behavior of poly(ether ether ketone) were studied by differential scanning calorimetry (DSC) and temperature-modulated DSC (TMDSC). The isothermal crystallization was performed between 290 and 320 °C. The Avrami exponents and the level off time were determined from the Avrami analysis. The minimum induction time required for the occurrence of double melting peaks was obtained by increasing the isothermal crystallization time in steps of one minute. It was found that the level off time did not represent the delimitation of single- or double-melting peak behavior. To elucidate the behavior of double melting peaks, the samples were crystallized isothermally between 280 and 320 °C for 10 min, and then they were heated to 380 °C at 2 °C/min. From the TMDSC results, the exothermic behavior in the non-reversing curves supports the mechanism of melting–recrystallization at T_c≤310 °C. On the other hand, no exothermic flow for T_c at 320 °C supports the mechanism of two different morphologies. As the isothermal crystallization temperature increased from 280 to 320 °C, the contribution of melting–recrystallization to the upper melting peak gradually decreased, and finally disappeared.     

Study of multiple melting behaviour of syndiotactic polystyrene in β‐crystalline form

A series of syndiotactic polystyrene (SPS) samples in β‐crystalline form were prepared by cooling from the melt at various rates. The effects of cooling rate from the melt, DSC heating rate and annealing on the multiple melting behaviours of β crystals were investigated by differential scanning calorimetry (DSC) and temperature modulated differential scanning calorimetry (TMDSC), from which the nature of the multiple melting behaviour was determined. The two melting endotherms of β‐form crystals were considered to arise from the occurrence of simultaneous melting, recrystallization and remelting processes in the melting region. It is suggested that the lower melting endotherm is due to the melting of imperfect β crystals originally present in the sample, whereas the higher melting endotherm comes from the melting of recrystallized SPS crystals, ie more perfect β crystals that formed during the DSC scanning process. © 2000 Society of Chemical Industry     

Sequence distribution, crystallization and melting behavior of poly(ethylene terephthalate-co-trimethylene terephthalate) copolyesters

The compositions of a series of copolyesters of ethylene- and trimethylene- terephthalate were determined by NMR. The values of randomness parameter revealed these copolyesters were random copolymers with average-number sequence lengths varied from 1 to 10. These copolyesters were investigated using temperature-modulated differential scanning calorimeter (TMDSC) and wide angle X-ray diffractometer (WAXD). The crystallization behavior was evidenced from the non-isothermal DSC thermograms and WAXD patterns. The crystallization rate and the intensity of diffraction peaks decrease with increasing the minor co-monomer content. The copolyester with equal amounts of monomers is still crystallizable even though the average sequence length is only 2.0, and its WAXD pattern is quite different from those of homopolymers. In the melting study, three distinct peaks of reversing melting were observed. Two peaks in the high temperature side are due to remelting of the recrystallized crystals formed during the heating scan, whereas the highest temperature peak is attributed to the melting of the crystals that are formed in relatively high temperature. The results of WAXD and TMDSC support the mechanism of melting-recrystallization-remelting for the multiple melting behaviors.     

Nonisothermal crystallization kinetics of biodegradable poly(butylene succinate)/poly(vinyl phenol) blend

Nonisothermal melt crystallization kinetics of biodegradable PBSU/PVPh blend was investigated with differential scanning calorimetry (DSC) from the viewpoint of practical application. PBSU/PVPh blends were cooled from the melt at various cooling rates ranging from 2.5 to 40°C/min. The crystallization peak temperature decreased with increasing the cooling rate for both neat and blended PBSU. Furthermore, the crystallization peak temperature of PBSU in the blend was lower than that of neat PBSU at a given cooling rate. Two methods, namely the Avrami equation and the Tobin method, were used to describe the nonisothermal crystallization of PBSU/PVPh blend. It was found that the Avrami equation was more suitable to predict the nonisothermal crystallization of PBSU/PVPh blend than the Tobin method. The effects of cooling rate and blend composition on the crystallization behavior of PBSU were studied in detail. It was found that the crystallization rate decreased with decreasing the cooling rate for both neat and blended PBSU. However, the crystallization of PBSU blended with PVPh was retarded compared with that of neat PBSU at the same cooling rate. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 972–978, 2007     

Copolyester studies. II. Melting and crystallization behavior of tetramethylene terephthalate–tetramethylene sebacate copolymers

The melting and crystallization behavior of poly(tetramethylene terephthalate) and its copolymers with tetramethylene sebacate (≯ 20 mol %) has been studied using differential scanning calorimetry (DSC). The effect of the sebacate concentration on equilibrium melting temperature and crystallization behavior is discussed in terms of the theory of equilibrium crystallization of random copolymers. The multiple-melting behavior of these systems is described and interpreted in terms of the theory of equilibrium melting of chain-folded crystals, together with molecular fractionation during crystallization and melting and recrystallization during the DSC scan.     

Thermophysical properties of bacterial poly(3‐hydroxybutyrate): Characterized by TMA,DSC, and TMDSC

The melting, isothermal and nonisothermal crystallization behaviors of poly(3‐hydroxybutyrate) (PHB) have been studied by means of temperature modulated differential scanning calorimetry (TMDSC) and conventional DSC. Various experimental conditions including isothermal/annealing temperatures (80, 90, 100, 105, 110, 120, 130, and 140°C), cooling rates (2, 5, 10, 20, and 50°C/min) and heating rates (5, 10, 20, 30, 40, and 50°C/min) have been investigated. The lower endothermic peak (T_m1) representing the original crystals prior to DSC scan, while the higher one (T_m2) is attributed to the melting of the crystals formed by recrystallization. Thermomechanical analysis (TMA) was used to evaluate the original melting temperature (T_melt) and glass transition temperature (T_g) as comparison to DSC analysis. The multiple melting phenomenon was ascribed to the melting‐recrystallization‐remelting mechanism of the crystallites with lower thermal stability showing at T_m1. Different models (Avrami, Jeziorny‐modified‐Avrami, Liu and Mo, and Ozawa model) were utilized to describe the crystallization kinetics. It was found that Liu and Mo's analysis and Jeziorny‐modified‐Avrami model were successful to explain the nonisothermal crystallization kinetic of PHB. The activation energies were estimated in both isothermal and nonisothermal crystallization process, which were 102 and 116 kJ/mol in respective condition. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42412.     

Crystallization behaviour of biodegradable poly(ethylene succinate) from the amorphous state

Nonisothermal and isothermal crystallization kinetics of biodegradable poly(ethylene succinate) (PES) from the amorphous state were studied by differential scanning calorimetry (DSC). For the nonisothermal crystallization, there were two crystallization exotherms upon heating from the amorphous state. One major crystallization exotherm located at low temperature corresponded to the real cold crystallization of PES, while the other minor one located at high temperature may correspond to the melt-recrystallization of the unstable crystals formed during the nonisothermal crystallization earlier. Several methods, such as Avrami equation, Tobin equation and Ozawa equation, were applied to describe the nonisothermal crystallization process of PES. Meanwhile, Avrami equation was also employed to study the isothermal crystallization of PES from the amorphous state. Similar to the nonisothermal crystallization the minor crystallization exotherm was also found in the DSC trace upon heating to the melt after the isothermal cold crystallization finished completely, and was attributed to the melt-recrystallization of the unstable crystals formed during the isothermal cold crystallization. Temperature modulated differential scanning calorimetry (TMDSC) was used in this work to investigate the origin of the minor crystallization exotherm located at high temperature, and the TMDSC experiments gave a direct evidence that the origin of the minor crystallization exotherm was from the melt-recrystallization of the originally existed unstable crystals formed through previous crystallization.     

Biodegradable poly(ethylene succinate) blends and copolymers containing minor amounts of poly(butylene succinate)

Poly(ethylene succinate) (PES), poly(butylene succinate) (PBS), and PES‐rich copolyesters were synthesized using an effective catalyst, titanium tetraisopropoxide. PES was blended with minor amounts of PBS for the comparison. The compositions of the copolyesters and the blends were determined from NMR spectra. Their thermal properties were studied using a differential scanning calorimeter (DSC), a temperature modulated DSC (TMDSC), and a thermogravimetric analyzer. No significant difference exists among the thermal stabilities of these polyesters and blends. For the blends, the reversible curves of TMDSC showed a distinct glass‐rubber transition temperature (T_g), however, the variation of the T_g values with the blend compositions was small. Isothermal crystallization kinetics and the melting behavior after crystallization were examined using DSC. Wide‐angle X‐ray diffractograms (WAXD) were obtained for the isothermally crystallized specimens. The results of DSC and WAXD indicate that the blends have a higher degree of crystallinity and a higher melting temperature than those of the corresponding copolymers. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010