Impact-modified poly(styrene-co-acrylonitrile) blends containing both oxazoline-functionalized poly(ethene-co-1-octene) elastomers and poly(styrene-co-maleic anhydride) as compatibilizer

Blends of a poly(styrene-co-acrylonitrile) (SAN) with poly(ethene-co-1-octene) rubber (EOR) were investigated. An improved toughness–stiffness balance was obtained when adding as a compatibilizer a blend consisting of oxazoline-functionalized EOR, prepared by grafting EOR with oxazoline-functional maleinate, and poly(styrene-co-maleic anhydride) (SMA), which is miscible with SAN. Enhanced interfacial adhesion was evidenced by the improved dispersion of the EOR in the SAN matrix and the reduced glass transition temperature of the dispersed EOR phase. Morphology studies using transmission electron microscopy revealed formation of an interphase between the matrix and the rubber particles. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 1685–1695, 1999     

Blends of poly(2,6-dimethyl-1,4-phenylene oxide)/ poly(styrene-co-methacrylic acid)/ poly(ethyl methacrylate-co-4-vinylpyridine)

Summary The miscibility of poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) with poly(styrene-co-acrylic acid) (SAA) or poly(styrene-co-methacrylic acid) (SMA) containing respectively up to 22 mol % of acrylic or methacrylic acid was studied by Differential Scanning Calorimetry and viscosimetry. All PPO/SAA or PPO/SMA blends containing 60% or less by weight of PPO were miscible and showed only one glass transition temperature (Tg). Above 60% of PPO, two Tg's were however observed for the blends in which the acid content in the SAA or SMA reaches 20% or 12% by mole respectively; the higher Tg is slightly lower than the one of pure PPO, while the lower one corresponds to a miscible blend of lower content of PPO.A DSC study showed that depending on the blend ratio, two or three glass transition temperatures were observed when a copolymer of ethyl methacrylate containing 8 mol % of 4-vinylpyridine (EM4VP-8) was added to miscible PPO/SMA-12 blends. The PPO dissolution in the SMA-12 copolymer was affected by the specific interactions that occurred between this latter copolymer and the EM4VP-8.     

Study of the miscibility of poly(ethyl methacrylate-co-4-vinylpyridine)/poly(styrene-co-cinnamic acid) blends

Summary The miscibility of a series of poly(ethyl methacrylate-co-4-vinylpyridine) with poly(styrene-co-cinnamic acid), is investigated by differential scanning calorimetry. The results show that each blend is miscible as ascertained by a single composition dependent glass transition temperature. The Tg's of the blends exhibit positive deviations from the weight average Tg's of the blend components. The thermograms data exploited according to the Kwei and Schneider approaches suggest the occurrence of strong specific intermolecular attractive interactions within the binary systems. The strength of these interactions, as estimated from the Kwei q-values, increases with the proton donor and proton acceptor contents in the copolymers. Received: 23 January 1999/Revised version: 29 April 1999/Accepted: 1 June 1999     

Effect of dehydrochlorination of PVC on miscibility and phase separation of binary and ternary blends of poly(vinyl chloride), poly(ethylene-co-vinyl acetate) and poly(styrene-co-acrylonitrile)

The enhancement of miscibility at the lower critical solution temperature (LCST) of the blends poly(vinyl chloride)/poly(ethylene-co-vinyl acetate) (PVC/EVA), poly(vinyl chloride)/poly(styrene-co-acrylonitrile) (PVC/SAN) and poly(vinyl chloride)/poly(ethylene-co-vinyl acetate)/poly(styrene-co-acrylonitrile) (PVC/EVA/SAN) was observed at the micron level. Such miscibility is attributed to the dehydrochlorination and formation of hydrogen bonds between blend components. However, macrolevel immiscibility of these blends heated to the LCST was observed. Such microdomain compatibility of these blends gives a synergistic character. Brittle-type failure observed for LCST samples testifies to the synergism in treated blends. ©1997 SCI     

Morphology and physical properties of SAN/NBR blends: The effect of AN content and melt viscosity of SAN

To study the effect of dispersed poly(butadiene-co-acrylonitrile) (NBR) rubber size on the physical properties of poly(styrene-co-acrylonitrile) (SAN)/NBR blends, SANs with various melt viscosities and acrylonitrile (AN) contents were examined. The dispersed size of NBR, whose AN content is 30 wt %, was reduced as the melt viscosity of the SAN matrix was increased or as the AN content of the SAN matrix was reduced in the range of 19–32 wt %. As the melt viscosity of the SAN matrix was increased, the damping peak of the NBR phase moved to a higher temperature, and as the AN content of SAN was reduced, the damping peak of the SAN phase moved to a lower temperature. Higher values of impact strength and elongation at break and reduced yield behavior at a low shear rate were observed at a finer dispersion of NBR. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 935–941, 1999     

Studies on polymer blends with moderate specific interactions. 2. phase structure of blends SAN/TPU and SAN/TPU/EVA

This paper deals with morphological studies of binary and ternary blends composed of poly(styrene-co-acrylonitrile) (SAN), polyurethane elastomer (TPU) and poly(ethylene-co-vinyl acetate) (EVA). Selective etching was found necessary to expose the morphologies of the blends. Chloroform or hot acetone, hexane/toluene (2/1v/v) and NaOH/CH₃OH (1wt%) were found to be selective etching agents for SAN, EVA and TPU, respectively. SAN and TPU form blends with fine dispersion structure, while SAN and EVA lead to rough phase structure with poor phase adhesion. These results are in accordance with the difference in the mechanical properties of SAN/TPU and SAN/EVA. In addition, for SAN/TPU/EVA blends, if TPU is only a minor component, it is preferentially located at the interphase, playing the role of a compatibilizer. As the amount of TPU increases, the compatibility is gradually improved. ©1997 SCI     

Miscibility windows in ternary polymer blends of a polyester,polymethacrylate and poly(styrene‐co‐acrylonitrile)

Miscibility, phase diagrams and morphology of poly(ε‐caprolactone) (PCL)/poly(benzyl methacrylate) (PBzMA)/poly(styrene‐co‐acrylonitrile) (SAN) ternary blends were investigated by differential scanning calorimetry (DSC), optical microscopy (OM), and scanning electron microscopy (SEM). The miscibility window of PCL/PBzMA/SAN ternary blends is influenced by the acrylonitrile (AN) content in the SAN copolymers. At ambient temperature, the ternary polymer blend is completely miscible within a closed‐loop miscibility window. DSC showed only one glass transition temperature (T_g) for PCL/PBzMA/SAN‐17 and PCL/PBzMA/SAN‐25 ternary blends; furthermore, OM and SEM results showed that PCL/PBzMA/SAN‐17 and PCL/PBzMA/SAN‐25 were homogeneous for any composition of the ternary phase diagram. Hence, it demonstrated that miscibility exists for PCL/PBzMA/SAN‐17 and PCL/PBzMA/SAN‐25 ternary blends, but that the ternary system becomes phase‐separated outside these AN contents. Copyright © 2003 Society of Chemical Industry     

Fourier transform infrared spectroscopic studies of the poly(styrene-co-acrylonitrile) and poly (vinyl chloride-co-vinyl acetate) blends

The Fourier transform infrared (FTIR) spectroscopic studies of the poly-(styrene-co-acrylonitrile) (SAN) and poly(vinyl chloride-co-vinyl acetate) (VYHH) blends produced by different blending techniques, viz., solution blending, melt-blending, and also the co-precipitation methods of blending, were performed. In the case of miscible blend systems, substantial band shiftings took place, whereas immiscible blend systems showed slight or no band shifting. The miscible blends showed a substantial residual spectrum which was absent in the case of the immiscible system when a similar subtraction process was carried out. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 63: 991–1000, 1997     

Phase Behaviour of Poly(ethylene oxide)/Poly(styrene-co-maleic anhydride) Blends

Thermal behaviour and morphology of blends of poly(ethylene oxide) (PEO) and poly(styrene-co-maleic anhydride) (SMA) prepared by the coprecipitation technique were studied by means of differential scanning calorimetry, optical microscopy and thermogravimetry. SMA containing 25wt% maleic anhydride (MA) was found to be miscible with PEO when the SMA content was greater than 80%. The melting temperature and crystallinity depended on the composition of the blend. SMA appears to segregate interlamellarly during the isothermal crystallization of PEO. The thermal stability of blends was enhanced and was higher than that of pure PEO and SMA. © of SCI.     

Miscibility studies of polymer blends by viscometry methods

The intrinsic viscosities of blends of poly(vinyl chloride)/poly(ethylene-co-vinyl acetate) (PVC/EVA), poly(vinyl chloride)/poly(styrene-co-acrylonitrile) (PVC/SAN), and poly(ethylene-co-vinyl acetate)/poly(styrene-co-acrylonitrile) (EVA/SAN) have been studied in cyclohexanone as a function of blend composition. In order to predict the compatibility of polymer pairs in solution, the interaction parameter term, Δb, obtained from the modified Krigbaum and Wall theory, and the difference in the intrinsic viscosities of the polymer mixtures and the weight average intrinsic viscosities of the two polymer solutions taken separately are used. © 1994 John Wiley & Sons, Inc.     

A new class of transparent polymeric materials. III. Miscible blends of poly(N-methylmaleimide-alt-isobutene) with poly(acrylonitrile-co-styrene) and the properties of the blends

The blend miscibility of poly(N-methylmaleimide-alt-isobutene) [poly-(MeMI-IB)] with poly(acrylonitrile-co-styrene) (SAN) was investigated by means of measurement of the glass transition temperature of the blends. Poly(MeMI-IB) was found to be miscible with SAN of a specific range of acrylonitrile (AN) contents in the copolymer to produce transparent moldings. The refractive index changed from 1.58 to 1.53 and the dispersion decreased with increasing the amount of poly(MeMI-IB) in the blends. The stress optical coefficient of poly(MeMI-IB) was found to be reduced by the blending of SAN. The glass transition temperature, flexural modulus, and surface hardness of the blends increased with an increase in the amount of poly(MeMI-IB) in the blend. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 63: 925–929, 1997     

Viscoelastic properties of blends of poly(methyl methacrylate) and poly(styrene‐co‐acrylonitrile) having various acrylonitrile contents

Dynamic viscoelastic properties of blends of poly(methyl methacrylate) (PMMA) and poly(styrene‐co‐acrylonitrile) (SAN) with various AN contents were measured to evaluate the influence of SAN composition, consequently χ parameter, upon the melt rheology. PMMA/SAN blends were miscible and exhibited a terminal flow region characterized by Newtonian flow, when the acrylonitrile (AN) content of SAN ranges from 10 to 27 wt %. Whereas, PMMA/SAN blends were immiscible and exhibited a long time relaxation, when the AN content in SAN is less than several wt % or greater than 30 wt %. Correspondingly, melt rheology of the blends was characterized by the plots of storage modulus G′ against loss modulus G″. Log G′ versus log G″ plots exhibited a straight line of slope 2 for the miscible blends, but did not show a straight line for the immiscible blends because of their long time relaxation mechanism. The plateau modulus, determined as the storage modulus G′ in the plateau zone at the frequency where tan δ is at maximum, varied linearly with the AN content of SAN irrespective of blend miscibility. This result indicates that the additivity rule holds well for the entanglement molecular weights in miscible PMMA/SAN blends. However, the entanglement molecular weights in immiscible blends should have “apparent” values, because the above method to determine the plateau modulus is not applicable for the immiscible blends. Effect of χ parameter on the plateau modulus of the miscible blends could not be found. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Melt rheology of poly(ϵ‐caprolactone)/poly(styrene‐co‐acrylonitrile) blends

Dynamic viscoelastic properties for miscible blends of poly(?‐caprolactone) (PCL) and poly(styrene‐co‐acrylonitrile) (SAN) were measured. It was found that the time–temperature superposition principle is applicable over the entire temperature range studied for the blends. The temperature dependency of the shift factors a_T can be expressed by the Williams–Landel–Ferry equation: log a_T = ?8.86(T ? T_s)/(101.6 + T ? T_s). The compositional dependency of T_s represents the Gordon–Taylor equation. The zero‐shear viscosities are found to increase concavely upward with an increase in weight fraction of SAN at constant temperature, but concavely downward at constant free volume fraction. It is concluded that the relaxation behavior of the PCL/SAN blends is similar to that of a blend consisting of homologous polymers. It is emphasized that the viscoelastic functions of the miscible blends should be compared in the iso‐free volume state. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 2037–2041, 2001     

Effect of tacticity of poly(methyl methacrylate) on the miscibility with poly(styrene‐co‐acrylonitrile)

Isotactic, atactic, and syndiotactic poly(methyl methacrylates) (PMMAs) (designated as iPMMA, aPMMA, and sPMMA) with approximately the same molecular weight were mixed separately with poly(styrene‐co‐acrylonitrile) (abbreviated as PSAN) containing 25 wt % of acrylonitrile in tetrahydrofuran to make three polymer blend systems. Differential scanning calorimetry (DSC) was used to study the miscibility of these blends. The results showed that the tacticity of PMMA has a definite impact on its miscibility with PSAN. The aPMMA/PSAN and sPMMA/PSAN blends were found to be miscible because all the prepared films were transparent and showed composition dependent glass transition temperatures (T_gs). The glass transition temperatures of the two miscible blends were fitted well by the Fox equation, and no broadening of the glass transition regions was observed. The iPMMA/PSAN blends were found to be immiscible, because most of the cast films were translucent and had two glass transition temperatures. Through the use of a simple binary interaction model, the following comments can be drawn. The isotactic MMA segments seemed to interact differently with styrene and with acrylonitrile segments from atactic or syndiotactic MMA segments. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2894–2899, 1999     

Kinetics of phase separation of poly(styrene‐co‐methyl methacrylate) and poly(styrene‐co‐acrylonitrile) blends

The phase behavior and kinetics of phase separation for blends of the random copolymer poly(styrene‐co‐methyl methacrylate) (SMMA) and poly(styrene‐co‐acrylonitrile) (SAN) were studied by using small‐angle laser light scattering. The partially miscible SMMA/SAN blends undergo spinodal decomposition (SD) and subsequent domain coarsening when quenched inside the unstable region. For blends of SMMA and SAN, the early stages of the phase separation process could be observed, unlike a number of other blends where the earliest stages are not visible by light scattering. The process was described in terms of the Cahn–Hilliard linear theory. Subsequently, a coarsening process was detected and the time evolution of q_m at the beginning of the late stages of phase separation followed the relationship q_m∝t^?1/3, corresponding to an evaporation–condensation mechanism. Self‐similar growth of the phase‐separated structures at different timescales was observed for the late stage. Copyright © 2004 Society of Chemical Industry     

Miscibility of copolycarbonate blends with poly(styrene-co-acrylonitrile) copolymer and their interaction energies

The phase behavior of dimethyl polycarbonate-tetramethyl polycarbonate (DMPC-TMPC) blends with poly(styrene-co-acrylonitrile) copolymers (SAN) and the interaction energies of binary pairs involved in blend has been explored. DMPC-TMPC copolycarbonates containing 60 wt% TMPC or more were formed miscible blends with SAN containing limited amounts of AN. The miscibility of copolycarbonate with SAN decreases as the DMPC content increases. The miscible blends showed the LCST-type phase behavior or did not phase separate until thermal degradation. The binary interaction energies involved in the miscible blends were calculated from the phase boundaries using the lattice-fluid theory combined with binary interaction model. The phenyl ring substitution with methyl groups did not lead to interactions that are favorable for miscibility with polyacrylonitrile (PAN). The interaction energies of the polycarbonates blends with SAN copolymers as a function of AN content were obtained. It was revealed that the incline of the number of methyl groups on the phenyl rings of bisphenol-A unit acts favorably for the miscibility with SAN copolymer when SAN contains less than about 30 wt% AN and shifts the most favorable interaction to the low AN content.     

Synthesis of poly[(2‐oxo‐1,3‐dioxolan‐4‐yl)methyl vinyl ether‐co‐N‐phenylmaleimide] and its miscibility in blends with styrene‐acrylonitrile or poly(vinyl chloride)

The aim of the study was to investigate the synthesis of a copolymer bearing cyclic carbonate and its miscibility with styrene/acrylonitrile copolymer (SAN) or poly(vinyl chloride) (PVC). (2‐Oxo‐1,3‐dioxolan‐4‐yl)methyl vinyl ether (OVE) as a monomer was synthesized from glycidyl vinyl ether and CO₂ using quaternary ammonium chloride salts as catalysts. The highest reaction rate was observed when tetraoctylammonium chloride (TOAC) was used as a catalyst. Even at the atmospheric pressure of CO₂, the yield of OVE using TOAC was above 80% after 6 h of reaction at 80°C. The copolymer of OVE and N‐phenylmaleimide (NPM) was prepared by radical copolymerization and was characterized by FTIR and ¹H‐NMR spectroscopies and differential scanning calorimetry (DSC). The monomer reactivity ratios were given as r₁ (OVE) = 0.53–0.57 and r₂ (NPM) = 2.23–2.24 in the copolymerization of OVE and NPM. The films of poly(OVE‐co‐NPM)/SAN and poly(OVE‐co‐NPM)/PVC blends were cast from N‐dimethylformamide. An optical clarity test and DSC analysis showed that poly(OVE‐co‐NPM)/SAN and poly(OVE‐co‐NPM)/PVC blends were both miscible over the whole composition range. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1809–1815, 2000     

Reactive melt blends of nylon with poly(styrene-co-maleic anhydride)

Melt blends of nylon with poly(styrene-co-maleic anhydride) (SMA) were prepared in a twin-screw extruder. Viscoelastic properties of the melt and morphological, thermal, and mechanical properties of the blends were determined. Fourier-transform infrared (FTIR) spectroscopy measurement indicated reactions between nylon and SMA. Melting peak temperature (T_m) of nylon was not changed in blends. This, together with the FTIR results, assured that the reactions occur mainly with the free amide end groups of nylon. Melt viscosity, elasticity, and the heat-distortion temperature (HDT) of nylon was significantly increased with the addition of SMA. Tensile strength and impact strength of nylon were, respectively, in general, increased and decreased with SMA.     

Dielectric relaxation study of poly(styrene-co-4-vinylbenzoic acid)/poly(ethyl methacrylate-co-4-vinylpyridine) blends

Summary The α-relaxations, located in the neighborhood of glass-transition region (Tg), of a styrene-co-4-vinylbenzoic acid (PSVBA) random copolymer blended in several weight proportions with an ethyl methacrylate-co-4-vinylpyridine (PEMAVP) random copolymer have been investigated by dielectric spectroscopy in the temperature and frequency ranging from 25 to 180 °C and 0.1 to 100 kHz, respectively. The analysis of the obtained results shows that the dielectric spectra of the miscible blends, essentially dominated by the response of PEMAVP, are composition dependent becoming broader with its content. These observations are correlated with segmental dynamic heterogeneities and blend concentration fluctuations. Received: 21 December 1998/Revised version: 21 March 1999/Accepted: 20 April 1999     

Polymer blends of stereoregular poly(methyl methacrylate) and poly(styrene‐co‐p‐hydroxystyrene)

Isotactic, atactic, and syndiotactic poly(methyl methacrylates) (PMMAs) (designated as iPMMA, aPMMA, and sPMMA) were mixed with poly(styrene‐co‐p‐hydroxystyrene) (abbreviated as PHS) containing 15 mol % of hydroxystyrene separately in 2‐butanone to make three polymer blend systems. Differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy were used to study the miscibility of these blends. The three polymer blends were found to be miscible, because all the prepared films were transparent and there was a single glass transition temperature (T_g) for each composition of the polymers. T_g elevation (above the additivity rule) is observed in all the three PMMA/PHS blends mainly because of hydrogen bonding. If less effective hydrogen bonding based on the FTIR evidence is assumed to infer less exothermic mixing, sPMMA may not be miscible with PHS over a broader range of conditions as iPMMA and aPMMA. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 431–440, 1999