Crystal Growth of Rod-Shaped β-LiA1O2

LiAlO₂crystals are obtained conventionally in the form of powder. In a few publications, crystal growth of rod-shaped LiAlO₂ has been described, but the fiber length was very short, <4 μm. In the present study, rod-shaped β-LiAIO₂ crystals 10 to 15 μm long were grown using LiOH-AI₂O₃NaOH as the raw material.     

Populations and Emission Properties of the 5I6 and 5I7 Levels in Ho3+ Doped into PbO–Bi2O3–Ga2O3 Glasses

Emission properties of PbO–Bi₂O₃–Ga₂O₃ glasses doped with Ho³⁺ were investigated for fiber-optic amplification at the 1.18 μm wavelength region. When the glasses were doped with Ho³⁺ ions only, there was a weak emission at 1.18 μm with a lifetime of ∼200 μs. However, when Yb³⁺ ions were codoped, the lifetime of the 1.18 μm emission increased to 630 μs together with a significant increase in intensity. A similar enhancement in the intensity and lifetimes was realized for the 2.05 μm emission. These effects are due to energy transfer from the Yb³⁺:²F_5/2 to the Ho³⁺:⁵I₆ level. Devitrification of the ternary PbO–Bi₂O₃–Ga₂O₃ glasses was efficiently suppressed by adding 10 mol% GeO₂. Optimum Ho³⁺ concentration was ∼0.4 mol%, whereas Yb³⁺ ions can be added up to the solubility limit.     

Synthesis of Micron-Scale Platelet BaTiO3

Micron-scale platelet barium titanate was synthesized using a twostep molten salt and topochemical technique. Plate-like BaBi₄Ti₄O₁₅ was first synthesized as a precursor by molten salt synthesis. Then, Bi³⁺ in the precursor was replaced by Ba²⁺ and formed perovskite-structure BaTiO₃ through a topochemical reaction. The BaTiO₃ single crystals have an average size of 5–10 μm and a thickness of 0.5 μm. The purpose of this article is to control the particle shape with desired structure. High aspect ratio BaTiO₃ platelets are suitable templates to obtain textured ceramics (especially Pb(Mg_1/3Nb_2/3)O₃–32.5PbTiO₃) by the templated grain growth process.     

Microfabrication of Three-Dimensional Photonic Crystals of SiO2–Al2O3 Ceramics and Their Terahertz Wave Properties

Dense three-dimensional microphotonic crystals of SiO₂–Al₂O₃ ceramics were fabricated using microstereolithography and successive sintering process. The forming dimensional tolerance for a 50 vol% ceramic paste is 10 μm and sintering shrinkage is around 12%. Diamond-type photonic crystals with lattice constants of 500 and 125 μm were formed and sintered successfully. The band gaps of the samples were measured and compared with the theoretically calculated band diagram.     

Preparation of Porous Ca10(PO4)6(OH)2 and β-Ca3(PO4)2 Bioceramics

Submicrometer-sized, pure calcium hydroxyapatite (HA, (Ca₁₀(PO₄)₆(OH)₂)) and β-tricalcium phosphate (β-TCP, Ca₃(PO₄)₂) bioceramic powders, that have been synthesized via chemical precipitation techniques, were used in the preparation of aqueous slurries that contained methyl cellulose to manufacture porous (70%–95% porosity) HA or β-TCP ceramics. The pore sizes in HA bioceramics of this study were 200–400 μm, whereas those of β-TCP bioceramics were 100–300 μm. The pore morphology and total porosity of the HA and β-TCP samples were investigated via scanning electron microscopy, water absorption, and computerized tomography.     

Residual α–Si3N4 in O' Crystals in CeO2-Doped O'+β' SiAlON Ceramics

The microstructure of a pressureless sintered (1605°C, 90 min) O'+β' SiAlON ceramic with CeO₂ doping has been investigated. It is duplex in nature, consisting of very large, slablike elongated O' grains (20–30 μm long), and a continuous matrix of small rodlike β' grains (< 1.0 μm in length). Many α-Si₃N₄ inclusions (0.1–0.5 μm in size) were found in the large O' grains. CeO₂-doping and its high doping level as well as the high Al₂O₃ concentration were thought to be the main reasons for accelerating the reaction between the α-Si₃N₄ and the Si-Al-O-N liquid to precipitate O'–SiAlON. This caused the supergrowth of O' grains. The rapid growth of O' crystals isolated the remnant α–Si₃N₄ from the reacting liquid, resulting in a delay in the α→β-Si₃N₄ transformation. The large O' grains and the α-Si₃N₄ inclusions have a pronounced effect on the strength degradation of O'+β' ceramics.     

Synthesis of High Aspect Ratio Platelet SrTiO3

A method for synthesis of high aspect ratio platelet seeds by growth of SrTiO₃ on Sr₃Ti₂O₇ core particles is reported. The aim of this study was to identify and control the morphology and size of SrTiO₃ particles via molten salt synthesis. Platelet and tabular morphologies with rectangular faces were obtained using rutile and anatase, respectively. Platelet SrTiO₃ particles with an edge length of 10–40 μm and a thickness of 1–4 μm were obtained. High aspect ratios (edge length to thickness) of 7–10 were measured for platelet particles as opposed to lower aspect ratios of 2–4 for tabular particles. Highly anisotropic platelets are suitable template candidates to achieve textured ceramics.     

Fabrication and Microstructures of MoSi2 Reinforced–Si3N4 Matrix Composites

Details of the fabrication and microstructures of hot-pressed MoSi₂ reinforced–Si₃N₄ matrix composites were investigated as a function of MoSi₂ phase size and volume fraction, and amount of MgO densification aid. No reactions were observed between MoSi₂ and Si₃N₄ at the fabrication temperature of 1750°C. Composite microstructures varied from particle–matrix to cermet morphologies with increasing MoSi₂ phase content. The MgO densification aid was present only in the Si₃N₄ phase. An amorphous glassy phase was observed at the MoSi₂–Si₃N₄ phase boundaries, the extent of which decreased with decreased MgO level. No general microcracking was observed in the MoSi₂–Si₃N₄ composites, despite the presence of a substantial thermal expansion mismatch between the MoSi₂ and Si₃N₄ phases. The critical MoSi₂ particle diameter for microcracking was calculated to be 3 μm. MoSi₂ particles as large as 20 μm resulted in no composite microcracking; this indicated that significant stress relief occurred in these composites, probably because of plastic deformation of the MoSi₂ phase.     

Porous Glass-Ceramics with a Skeleton of the Fast-Lithium-Conducting Crystal Li1+xTi2−xAlx(PO4)3

Porous glass-ceramics with a skeleton of the fast-lithium-conducting crystal Li_{1+ x} Ti_{2− x} Al _x (PO₄)₃ (where x = 0.3–0.5) were prepared by crystallization of glasses in the Li₂O─CaO─TiO₂─Al₂O₃–P₂O₅ system and subsequent acid leaching of the resulting dense glass-ceramics composed of the interlocking of Li_{1+ x} Ti_{2− x} Al _x (PO₄)₃ and β-Ca₃(PO₄)₂ phases. The median pore diameter and surface area of the resulting porous Li_{1+ x} Ti_{2− x} Al _x (PO₄)₃ glass-ceramics were approximately 0.2 μm and 50 m²/g, respectively. The electrical conductivity of the porous glass-ceramics after heating in LiNO₃ aqueous solution was 8 × 10⁻⁵ S/cm at 300 K or 2 × 10⁻² S/cm at 600 K.     

R-Curve Behavior of Si3N4–BN Composites

R -curve behavior of Si₃N₄–BN composites and monolithic Si₃N₄ for comparison was investigated. Si₃N₄–BN composites showed a slowly rising R -curve behavior in contrast with a steep R -curve of monolithic Si₃N₄. BN platelets in the composites seem to decrease the crack bridging effects of rod-shaped Si₃N₄ grains for small cracks, but enhanced the toughness for long cracks as they increased the crack bridging scale. Therefore, fracture toughness of the composites was relatively low for the small cracks, but it increased significantly to ∼8 MPa·m^1/2 when the crack grew longer than 700 μm, becoming even higher than that of the monolithic Si₃N₄.     

Microstructure and Mechanical Properties of the in situβ-Si3N4/α'-SiAlON Composite

The in situ β-Si₃N₄/α'-SiAlON composite was studied along the Si₃N₄–Y₂O₃: 9 AlN composition line. This two phase composite was fully densified at 1780°C by hot pressing Densification curves and phase developments of the β-Si₃N₄/α'-SiAlON composite were found to vary with composition. Because of the cooperative formation of α'-Si AlON and β-Si₃N₄ during its phase development, this composite had equiaxed α'-SiAlON (∼0.2 μm) and elongated β-Si₃N₄ fine grains. The optimum mechanical properties of this two-phase composite were in the sample with 30–40%α', which had a flexural strength of 1100 MPa at 25°C 800 MPa at 1400°C in air, and a fracture toughness 6 Mpa·m^1/2. α'-SiAlON grains were equiaxed under a sintering condition at 1780°C or lower temperatures. Morphologies of the α°-SiAlON grains were affected by the sintering conditions.     

Glass-Forming Systems Involving GeO2 with Bi2O3, Ti2O, and PbO

The previously studied system GeO₂-Bi₂O₃-TI₂O was extended with the addition of PbO using air- and water-quenched melted samples. Large areas of glass formation were found in the systems GeO₂–Bi₂O₃–PbO and GeO₂–PbO–Tl₂O at all but the lowest GeO₂ contents. Glasses were examined by powder X-ray diffraction, differential thermal analysis, thermomechanical analysis, and Archimedes'technique to obtain glass transition and crystallization exotherm temperatures, thermal expansion coefficients, and densities, which are presented in diagrams for the GeO₂-PbO binary and for the two ternary systems. Based on calculated values of λ₀, the wavelength for zero material dispersion, compositions in this system may be useful for construction of ultralow-loss optical waveguides in the μm region.     

Synthesis of LiAlO2 Powder by Hydrolysis of Metal Alkoxides

Crystalline fine powders of LiAlO₂ can be prepared by hydrolysis of metal alkoxides for application to the breeder blanket in nuclear fusion. The precipitates were fine crystalline particles of β-LiAlO₂of ∼0.1-μm size under controlled conditions. The transformation from β- to γ-phase was confirmed at temperatures between 700° and 750°C. The microstructure of a sintered body at 1000°C consisted of homogeneous fine particles and pores suitable for the blanket material. A fully dense sintered body could be prepared at 1400°C.     

Formation and Properties of GeSe2–Ga2Se3–PbI2 Novel Chalcohalide Glasses

The glass-forming region of the GeSe₂–Ga₂Se₃–PbI₂ system was determined and homogeneous glasses were prepared. The maximum dissolvable PbI₂ can be up to 50 mol%. The structures of glasses were characterized by Raman spectroscopy. The thermal, optical, and some basic physical properties of the glasses were investigated. The results show that GeSe₂–Ga₂Se₃–PbI₂ glasses have a wide region of transmission window (0.7–16 μm) and high refractive index (∼2.5) with the addition of PbI₂. The glasses have good glass-forming ability and high glass transition temperatures. Consequently, these novel glasses may be promising candidate materials for infrared optics and nonlinear optical field.     

Fabrication and Microstructure Characterization of Continuous Porous TiO2/Al2O3 Composite Membrane

Using a multipass extrusion process, continuous porous Al₂O₃ body (∼41% porosity) was produced and used as a substrate to fabricate continuous porous TiO₂/Al₂O₃ composite membrane. The diameter of the continuous pores of the porous Al₂O₃ body was about 150 μm. The TiO₂ nanopowders dip coated on the continuous pore-surface Al₂O₃ body existed as rutile and anatase phases after calcination at 520°C in air. However, after aging of the fabricated continuous porous TiO₂/Al₂O₃ composite membrane in 20% NaOH at 60°C for 24 h, a large number of TiO₂ fibers frequently observed on the pore surface. The diameter of the TiO₂ fibers was about 150 nm having a high specific surface area. However, after 48-h aging period, the diameter of the TiO₂ fibers increased, which was about 3 μm. Most of the TiO₂ fibers had polycrystalline structure having nanosized rutile and anatase crystals of about 20 nm.     

Phase Relationships in the Si3N4–SiO2–Lu2O3 System

Phase relationships in the Si₃N₄–SiO₂–Lu₂O₃ system were investigated at 1850°C in 1 MPa N₂. Only J-phase, Lu₄Si₂O₇N₂ (monoclinic, space group P 2₁/ c , a = 0.74235(8) nm, b = 1.02649(10) nm, c = 1.06595(12) nm, and β= 109.793(6)°) exists as a lutetium silicon oxynitride phase in the Si₃N₄–SiO₂–Lu₂O₃ system. The Si₃N₄/Lu₂O₃ ratio is 1, corresponding to the M-phase composition, resulted in a mixture of Lu–J-phase, β-Si₃N₄, and a new phase of Lu₃Si₅ON₉, having orthorhombic symmetry, space group Pbcm (No. 57), with a = 0.49361(5) nm, b = 1.60622(16) nm, and c = 1.05143(11) nm. The new phase is best represented in the new Si₃N₄–LuN–Lu₂O₃ system. The phase diagram suggests that Lu₄Si₂O₇N₂ is an excellent grain-boundary phase of silicon nitride ceramics for high-temperature applications.     

Subsolidus Phase Relationships in the Ga2O3–Al2O3–TiO2 System

Subsolidus phase relationships in the Ga₂O₃–Al₂O₃–TiO₂ system at 1400°C were studied using X-ray diffraction. Phases present in the pseudoternary system include TiO₂ (rutile), Ga_{2−2 x} Al_{2 x} O₃ ( x ≤0.78 β-gallia structure), Al_{2−2 y} Ga_{2 y} O₃ ( y ≤0.12 corundum structure), Ga_{2−2 x} Al_{2 x} TiO₅ (0≤ x ≤1 pseudobrookite structure), and several β-gallia rutile intergrowths that can be expressed as Ga_{4−4 x} Al_{4 x} Ti _{n −4}O_{2 n −2} ( x ≤0.3, 15≤ n ≤33). This study showed no evidence to confirm that aluminum substitution of gallium stabilizes the n =7 β-gallia–rutile intergrowth as has been mentioned in previous work.     

Effect of Sintering Aids on Microstructures and PTCR Characteristics of (Sr0.2Ba0.8)TiO3 Ceramics

The effects of liquid-phase sintering aids on the microstructures and PTCR characteristics of (Sr_0.2Ba_0.8)TiO₃ materials have been studied. The grain size of sintered materials monotonically decreases with increasing content of Al₂O₃–SiO₂–TiO₂ (AST). The ultimate PTCR properties with ρ_ht/ρ_rt as great as 10^5.61 are obtained for fine-grain (10-μm) samples, which contain 12.5 mol% AST and were sintered at 1350°C for 1.5 h. The quantity of liquid phase formed due to eutectic reaction between AST and (Sr,Ba)TiO₃ is presumably the prime factor in determining the grain size of samples. The grains grow rapidly at the sintering temperature in the first stage until the liquid phase residing at the grain boundaries reaches certain critical thickness such that the liquid–solid interfacial energy dominates the mechanism of grain growth.     

Fabrication and Characterization of γ-LiAlO2 Matrices Using an Aqueous Tape-Casting Process

A new aqueous tape-casting process that is simple and environment friendly has been developed to fabricate the γ-LiAlO₂ matrix for molten-carbonate fuel cells (MCFCs). Very-fast-drying green sheets having a thickness of 500–600 μm, no defects, and good workability have been obtained using an aqueous tape-casting process and protein. The microstructure of the γ-LiAlO₂ matrices (50%–60% porosity and 0.15 μm average pore size) required in a MCFC matrix can be prepared using this method.     

Glass Formation and Recrystallization in the Lithium Metasilicate Region of the System Li2O–Al2O3–SiO2

The stability of the vitreous state in the lithium metasilicate region of the system Li₂O–Al₂O₃–SiO₂ was found to be a function of the concentration of lithia. The higher the lithia content, the less stable was the glass. The devitrification of glasses in this system was studied. In addition to the phases present at or near the liquidus, it was found that the β -eucryptite– β -quartz solid solution phase was metastable over most of the region. The Li₂O–SiO₂, β -Li₂O–Al₂O₃–4SiO₂ solid solution, β -Li₂O–Al₂O₃–2SiO₂ solid solution triple point was estimated to be near 62.5% SiO₂, 17% Al₂O₃, and 20.5% Li₂O (by weight). The thermal expansions of bodies in this region were measured and the values obtained are explained in terms of the phases present.