Synthesis of rosin‐based imidoamine‐type curing agents and curing behavior with epoxy resin

Rosin is an abundantly available natural product. The characteristic fused ring structure of rosin acids is analogous to that of some aromatic compounds in rigidity, and makes rosin and its derivatives potential substitutes for those aromatic compounds. In the study reported, the synthesis of biobased curing agents containing imide structure using rosin and the cure reaction were investigated. Rosin‐based imidoamine‐type curing agents were synthesized, and the chemical structure was confirmed using ¹H NMR, Fourier transform infrared and electrospray ionization spectroscopy. The curing behavior with diglycidyl ether of bisphenol A epoxy was studied using differential scanning calorimetry. The thermal mechanical properties and thermal stability of the cured epoxy resins were evaluated using dynamic mechanical analysis and thermogravimetry, respectively. The results indicate that the curing behavior of the rosin‐based curing agents is similar to that of curing agents with analogous structures. Cured products have good thermal stability due to the presence of the imide group and the bulky hydrogenated phenanthrene ring structure. Rosin acids have a great potential in the synthesis of epoxy curing agents as replacements for some of the current commercial aromatic or cycloaliphatic analogues. Copyright © 2010 Society of Chemical Industry     

Use of eugenol and rosin as feedstocks for biobased epoxy resins and study of curing and performance properties

In this study, an epoxy based on eugenol and an anhydride curing agent based on rosin were prepared. Curing of the eugenol epoxy with a commercial anhydride curing agent and with the rosin‐derived anhydride curing agent was studied. For comparison, a commercial bisphenol A type epoxy, DER353, was also selected in the curing study. The syntheses of the eugenol epoxy and rosin anhydride were investigated and the chemical structures of the products and intermediates were characterized using ¹H NMR and Fourier transform infrared spectroscopies. Non‐isothermal curing of the eugenol epoxy with hexahydrophthalic anhydride and the rosin‐derived maleopimaric acid was studied using differential scanning calorimetry. Thermomechanical properties and thermal stability of the cured epoxy resins were evaluated using dynamic mechanical analysis and thermogravimetric analysis, respectively. Addition of 2‐ethyl‐4‐methylimidazole as catalyst greatly decreased the curing temperature and promoted the completion of cure reactions. The results suggest that the eugenol epoxy and the bisphenol A type epoxy have similar reactivity, dynamic mechanical properties and thermal stability. © 2013 Society of Chemical Industry     

Comparative study of silicon‐containing cycloaliphatic epoxides between different chemical structures and curing mechanisms for potential light‐emitting diode encapsulation applications

The aim of this paper is to systematically investigate the curing behavior of three novel di‐ and trifunctional silicon‐containing cycloaliphatic epoxy resins by both anhydride and cationic ring‐opening polymerization methods as well as the viscoelasticity, thermal stability, water absorption and optical properties of the cured products. Differential scanning calorimetry curves show that, relative to anhydride curing, cationic polymerization can decrease the curing temperature to below 120 °C, and the reaction exothermic peaks become very narrow and sharp, exhibiting rapid curing characteristics at moderately low temperature. In addition, the differences between the anhydride and cationic curing methods bring about interesting variations in physical properties for the cured products which are well related to their chemical structures, polymerization mechanism, crosslinking density, segmental flexibility and inter‐segmental distance. The excellent transparency, rapid cationic curing rate, good thermal stability and high glass transition temperature of over 275 °C make this series of epoxy resins promising candidates for light‐emitting diode encapsulation applications. © 2012 Society of Chemical Industry     

Comparison between microwave and thermal curing of glass fiber–epoxy composites: Effect of microwave‐heating cycle on mechanical properties

The objective of this study was to compare the mechanical properties between epoxy composites cured by thermal heating and microwave heating. Epoxy‐anhydride resins reinforced with glass fiber were cured in a domestic microwave oven and in a thermal oven. Hardening agents included methyl tetrahydrophthalic anhydride and methyl hexahydrophthalic anhydride. Microwave curing was carried out at various conditions, including 1‐, 2‐, and 3‐step heating cycle, whereby each cycle employed different power level and time. Mechanical properties were tested according to ASTM standards. It is found that the microwave‐cured composites produced mechanical properties as good as the thermally cured composites. The 2‐ and 3‐step heating cycle used in the microwave curing process produced better mechanical properties higher than those obtained from the microwaved 1‐step and thermally curing process. This is attributed to the slow increase in temperature during the beginning of the microwave curing process whereby the very low power level was applied in the first cycle of the multistep heating process. This affected the slower rate of viscosity increment, resulting in better wettability of the glass fiber with enhanced interfacial adhesion between the fibers and the resins. The viscosity of resins affected the homogeneity of the crosslinked structure. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1059–1070, 2006     

Comparison of microwave and thermal cure of epoxy–anhydride resins: Mechanical properties and dynamic characteristics

The objective of this work was to compare the mechanical properties of epoxy resins cured by thermal heating and microwave heating. Epoxy–anhydride (100:80) resins were cured in a domestic microwave oven and in a thermal oven. The hardening agents included methyl tetrahydrophthalic anhydride and methyl hexahydrophthalic anhydride. Three types of accelerators were employed. Thermal curing was performed at 150°C for 20 and 14 min for resins containing 1 and 4% accelerator, respectively. Microwave curing was carried out at a low power (207 or 276 W) for 10, 14, and 20 min. All cured resins were investigated with respect to their tensile properties, notched Izod impact resistance, and flexural properties (three‐point bending) according to ASTM standards. The tan δ and activation energy values were investigated with dynamic mechanical thermal analysis, and the extent of conversion was determined with differential scanning calorimetry. The differences in the mechanical properties of the thermally cured and microwave‐cured samples depended on the resin formulation and properties. Equivalent or better mechanical properties were obtained by microwave curing, in comparison with those obtained by thermal curing. Microwave curing also provided a shorter cure time and an equivalent degree of conversion. The glass‐transition temperatures (tan δ) of the thermally and microwave‐cured resins were comparable, and their activation energies were in the range of 327–521 kJ/mol. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1442–1461, 2005     

Phosphorous‐containing epoxy resins from a novel synthesis route

The ? P(O)‐H in 9,10‐dihydro‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO) was used as an active group to react with the carbonyl group in 4,4′‐dihydroxybenzophenone (DHBP) to result a novel phosphorous‐containing biphenol compound (DOPO‐2OH). Phosphorous‐containing epoxy resins were therefore obtained from reacting DOPO‐2OH with epichlorohydrin or with diglycidylether bisphenol A. The synthesized compounds were characterized with FTIR, ¹H and ³¹P NMR, elemental analysis, and epoxide equivalent weight titration to demonstrate the their chemical structures. Cured epoxy resins were prepared via thermal curing the epoxy resins with various curing agents. Thermal analysis results (differential scanning calorimetry and thermogravimetric analysis) revealed that these cured epoxy resins exhibited high glass transition temperatures and high thermal stability. High char yields at 700°C and high LOI (limited oxygen index) values were also found for the cured epoxy resins to imply that the resins were possessing high flame retardancy. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1697–1701, 2002     

Synthesis and characterization of emulsion‐type curing agent of water‐borne epoxy resin

Self‐emulsified water‐borne epoxy curing agent of nonionic type was prepared using triethylene tetramine (TETA) and derivative of epoxy resin as a capping agent, which was synthesized by liquid epoxy resin (E51) and polyethylene glycol (PEG), and the curing agent possessed emulsification and curing properties at the same time. The curing agent with good property of emulsifying liquid epoxy resin could be obtained under the condition of the molar ratio of PEG : E51 : TETA as 0.8 : 1 : 3.5 at 80°C for 5 h. The mean particle size of the emulsion liquid was about 220 nm with the prepared curing agent and epoxy resin at the mass ratio of 1 : 3. The structure of the emulsion‐type curing agent was confirmed by FTIR and ¹H NMR spectra, and the mechanism of cured film formation was also analyzed by SEM photographs. The cured film prepared by the emulsion‐type curing agent and epoxy resin under ambient cure conditions showed good properties even at high staving temperature. This study provides useful suggestions for the application of the water‐borne epoxy resins in coating industry. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2652–2659, 2013     

New polythiourethane hardeners for epoxy resins

New mercaptan‐terminated polythiourethanes were synthesized from low‐molecular‐weight dimercaptan oligomers and diisocyanates. The characteristic bands in the FT‐IR spectra, and the specific peaks in the ¹H‐NMR spectra correlate rather well with the proposed structures of these polymers. Chemical analysis of the epoxy group conversion and swelling measurements were conducted in order to determine the crosslink densities of the cured epoxy resins. The curing characteristics and thermal behaviour of the formulated curing mixtures indicate that the epoxy/polythiourethane stoichiometry and thermal history during cure may greatly affect the curing mechanism and final properties of the epoxy networks. Mechanical studies indicated that the application of polythiourethane hardeners improves the flexibility with increasing tensile strength and impact toughness. The prepared polythiourethane hardeners have an acceptable odour and give a perfectly homogeneous system with the epoxy resins and have good storage stability with other coreactants such as diamines. Copyright © 2005 Society of Chemical Industry     

Fabrication and Characterization of Glass Fiber Reinforced Composites from 2,3‐Epoxypropyl 3‐(2‐Furyl)acrylate and Acrylonitrile

The present paper comprises synthesis and characterization of 2,3‐epoxypropyl 3‐(2‐furyl)acrylate (EPFA) from 3‐(2‐furyl)acrylic acid (FAA) and epichlorohydrin, and its subsequent copolymerization with acrylonitrile (AN) by varying the ratio of EPFA:AN and time using benzoyl peroxide as initiator at 80°C in toluene. The resultant pre‐polymers were characterized by epoxy equivalent weight (EEW), viscosity measurement, gel permeation chromatography (GPC), and infrared (IR) spectral studies. The prepolymers were cured by employing two different curing agents viz. chlorosulfonic acid (ClSO₃H) and maleic anhydride/triethanolamine (MAN : TEA). The curing study was performed isothermally at 120 and 160°C, respectively, for the agents employed. Differential scanning calorimetry (DSC) was also employed to study the curing behavior on dynamic runs. The cured samples were analyzed by thermogravimetry for their thermal stability. The glass fiber reinforced composites (GFRC) were fabricated from selected resin samples and were characterized for their mechanical properties, electrical properties and chemical resistance.     

Synthesis of epoxy curing agents containing different ring structures and properties investigation of the cured resins

Two kinds of aliphatic epoxy curing agents containing ring structures were synthesized from rosin acid and isosorbide, respectively. They were cured with diglycidyl ether bisphenol A (DER331) and the ultimate propertied of the cured resins were investigated. For comparison, the petroleum‐based curing agent containing planar benzene ring was synthesized from terephthalic acid. The chemical structures of the synthesized curing agents were identified by Fourier transform‐infrared and H‐nuclear magnetic resonance. The ultimate properties of the cured epoxy resins were investigated by thermogravimetric analysis and dynamic mechanical analysis. Especially, the effects of ring structure on their shape memory properties were studied in terms of shape fixity, shape recovery, and shape recovery time. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44219.     

Synthesis,structure, and mechanical properties of castor oil‐based polyamidoamines toughened epoxy coatings

A series of toughened epoxy systems was prepared via crosslinking of diglycidyl ether of bisphenol A with castor oil‐based polyamidoamines as curing agents. To this aim two series of polyamidoamines were synthesized in two steps from the reaction of castor oil with triethylenetetramine and then reaction of these products with dissolved salicylic acid in dimethyl formamide (DMF). The structure of the compounds was confirmed by FTIR spectra, GC‐Mass and ¹H‐NMR spectroscopy. The mechanical properties, adhesion and water resistance of polyamine and polyamidoamines cured epoxy systems were studied. It was found that significant improvement in toughness and adhesion of the epoxy films was achieved by using polyamidoamines as curing agents. The results showed a great enhancement in toughness and adhesion properties of the epoxy coats proportional to increasing castor oil weight ratio, and/ or using salicylic acid and DMF. Furthermore, polyamidoamines cured samples showed higher water resistance and less degradation in hot water immersion tests than polyamine cured samples. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis and characterization of methacrylated star‐shaped poly(lactic acid) employing core molecules with different hydroxyl groups

A set of novel bio‐based star‐shaped thermoset resins was synthesized via ring‐opening polymerization of lactide and employing different multi‐hydroxyl core molecules, including ethylene glycol, glycerol, and erythritol. The branches were end‐functionalized with methacrylic anhydride. The effect of the core molecule on the melt viscosity, the curing behavior of the thermosets and also, the thermomechanical properties of the cured resins were investigated. Resins were characterized by Fourier‐transform infrared spectroscopy, ¹³C‐NMR, and ¹H‐NMR to confirm the chemical structure. Rheological analysis and differential scanning calorimetry analysis were performed to obtain the melt viscosity and the curing behavior of the studied star‐shaped resins. Thermomechanical properties of the cured resins were also measured by dynamic mechanical analysis. The erythritol‐based resin had superior thermomechanical properties compared to the other resins and also, lower melt viscosity compared to the glycerol‐based resin. These are of desired characteristics for a resin, intended to be used as a matrix for the structural composites. Thermomechanical properties of the cured resins were also compared to a commercial unsaturated polyester resin and the experimental results indicated that erythritol‐based resin with 82% bio‐based content has superior thermomechanical properties, compared to the commercial polyester resin. Results of this study indicated that although core molecule with higher number of hydroxyl groups results in resins with better thermomechanical properties, number of hydroxyl groups is not the only governing factor for average molecular weight and melt viscosity of the uncured S‐LA resins. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45341.     

High‐performance biobased epoxy derived from rosin

Great achievements have been made in the research of biobased thermoplastic polymers, but the progress concerning thermosetting resins has been minor. In particular, research on high‐performance thermosetting polymers from renewable feedstock has not been reported elsewhere. A novel biobased epoxy was synthesized from a rosin acid. Its chemical structure was confirmed using ¹H NMR, ¹³C NMR and Fourier transform infrared spectroscopy. The results indicated that the rosin‐based epoxy possessed high glass transition temperature (T_g = 153.8 °C), high storage modulus at room temperature (G′ = 2.4 GPa) and good thermal stability. A rosin‐based epoxy with excellent properties was achieved. The results suggest it is possible to develop high‐performance thermosetting resins from renewable resources. Copyright © 2010 Society of Chemical Industry     

Synthesis and properties of fluorinated biphenyl‐type epoxy resin

A novel fluorinated biphenyl‐type epoxy resin (FBE) was synthesized by epoxidation of a fluorinated biphenyl‐type phenolic resin, which was prepared by the condensation of 3‐trifluoromethylphenol and 4,4′‐bismethoxymethylbiphenyl catalyzed in the presence of strong Lewis acid. Resin blends mixed by FBE with phenolic resin as curing agent showed low melt viscosity (1.3–2.5 Pa s) at 120–122°C. Experimental results indicated that the cured fluorinated epoxy resins possess good thermal stability with 5% weight loss under 409–415°C, high glass‐transition temperature of 139–151°C (determined by dynamic mechanical analysis), and outstanding mechanical properties with flexural strength of 117–121 MPa as well as tensile strength of 71–72 MPa. The thermally cured fluorinated biphenyl‐type epoxy resin also showed good electrical insulation properties with volume resistivity of 0.5–0.8 × 10¹⁷ Ω cm and surface resistivity of 0.8–4.6 × 10¹⁶ Ω. The measured dielectric constants at 1 MHz were in the range of 3.8–4.1 and the measured dielectric dissipation factors (tan δ) were in the range of 3.6–3.8 × 10^?3. It was found that the fluorinated epoxy resins have improved dielectric properties, lower moisture adsorption, as well as better flame‐retardant properties compared with the corresponding commercial biphenyl‐type epoxy resins. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and evaluation of liquid amine‐terminated polybutadiene rubber and its role in epoxy toughening

Epoxy resin is widely used for coatings, adhesives, castings, electrical insulation materials, and other applications. However, unsolved problems still remain in its applications. The main problem is low toughness: cured epoxy resin is rather brittle, with poor resistance to the propagation of cracks derived from the internal stress generated by shrinkage in the cooling process from cure temperature to room temperature. The objective of this study was to improve the flexibility and toughness of diglycidyl ether of bisphenol A based epoxy resin with a liquid rubber. For this purpose, amine‐terminated polybutadiene (ATPB) was synthesized. The product was characterized by Fourier transform infrared and NMR spectroscopy and elemental analysis. ATPB‐modified epoxy networks were made by curing with an ambient‐temperature curing agent, triethylene tetramine. We varied the epoxy/liquid rubber compositions to study the effect of toughener concentration on the impact and thermal properties. Higher mechanical properties were obtained for epoxy resins toughened with 1 phr ATPB. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2446–2453, 2005     

Poly(ester‐amine) hyperbranched polymer as toughening and co‐curing agent for epoxy/clay nanocomposites

The marriage between hardness and flexibility of epoxy resins (improved toughness) is a desired feature, which broads their application in various industrial fields, especially for high impact resistance purposes. Accordingly, this work aims to improve toughness properties of epoxy resin (Epon‐828)/Ancamine (curing agent) system using amino‐terminated hyperbranched poly(ester‐amine) [Poly(PEODA‐NPA)] (HP) as toughening and/or co‐curing agent, in presence of organo‐modified Montmorillonite clay (OMMT) as a reinforcing filler. HP was synthesized via Michael addition reaction of poly(ethylene glycol) diacrylate (PEODA) to N‐methyl‐1,3‐propanediamine (NPA). Chemical structure and molecular weight of HP were elucidated using infrared (FTIR) spectroscopy and gel permeation chromatography (GPC) techniques, respectively. Epoxy/OMMT nanocomposites toughened with HP (at different concentrations) showed remarkable improvement in their toughness without any adverse effect on the other physico‐mechanical properties. The optimum concentration of HP and OMMT was found to be 20 wt % and 1–3 wt% of the epoxy resin, respectively. The extent of exfoliation and dispersion of OMMT platelets within the epoxy cured films was assessed by X‐ray diffraction (XRD) and transmission electron microscopy (TEM) measurements. In addition, thermal gravimetric analyses (TGA‐DTA) of epoxy/OMMT nanocomposites toughened with HP showed a slight increase in their decomposition temperature, particularly at low OMMT loading. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

A phosphorus‐containing diamine for flame‐retardant,high‐functionality epoxy resins. I. Synthesis,reactivity, and thermal degradation properties

A phosphorus‐containing amine, bis(4‐aminophenoxy)phenyl phosphine oxide (BAPP), suitable for curing epoxy resins with improved fire performance was synthesized and characterized with Fourier transform infrared spectroscopy and nuclear magnetic resonance. The reactivity of the amino group was evaluated by differential scanning calorimetry of the epoxy–amine mixture and by proton nuclear magnetic resonance of the amino unit. With BAPP as a curing agent, a range of high‐functionality, aerospace epoxy resins were cured, and the dynamic kinetic parameters calculated from Kissinger's and Ozawa's models were compared with those from the more widely used amines. The thermal degradation properties of the phosphorus‐containing epoxy resins were studied by thermogravimetric analysis, the degradation activation energy was calculated, and a multistep thermal degradation process was observed. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2093–2100, 2004     

Toughening of epoxy resins by hydroxy‐terminated,silicon‐modified polyurethane oligomers

Epoxy resins are among the most versatile engineering structural materials. A wide variety of epoxy resins are commercially available, but most are brittle. Several approaches have been used to improve the toughness of epoxy resins, including the addition of fillers, rubber particles, thermoplastics, and their hybrids, as well as interpenetrating polymer networks (IPNs) of acrylic, polyurethane, and flexibilizers such as polyols. This last approach has not received much attention; none of them have been able to suitably increase resin toughness with out sacrificing tensile properties. Therefore, in an attempt to fill this gap, we experimented with newly synthesized hydroxy‐terminated silicon‐modified polyurethane (SiMPU) oligomers as toughening agents for epoxy resins. SiMPU oligomers were synthesized from dimethyl dichlorosilane, poly(ethylene glycol) (weight‐average molecular weight ～ 200), and toluene 2,4‐diisocyanate and characterized with IR, ¹H‐NMR and ¹³C‐NMR, and gel permeation chromatography. The synthesized SiMPU oligomers, with different concentrations, formed IPNs within the epoxy resins (diglycidyl ether of bisphenol A). The resultant IPN products were cured with diaminodiphenyl sulfone, diaminodiphenyl ether, and a Ciba–Geigy hardener under various curing conditions. Various mechanical properties, including the lap‐shear, peel, and impact strength, were evaluated. The results showed that 15 phr SiMPU led to better impact strength of epoxy resins than the others without the deterioration of the tensile properties. The impact strength increased continuously and reached a maximum value (five times greater than that of the virgin resin) at a critical modifier concentration (20 phr). The critical stress intensity factor reached 3.0 MPa m^1/2 (it was only 0.95 MPa m^1/2 for the virgin resin). © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1497–1506, 2003     

A novel flame retardant UV‐curable vinyl ester resin monomer based on industrial dipentene: Preparation,characterization, and properties

A novel bio‐based and flame‐retardant UV‐curable vinyl ester resin (VER) monomer named Diglycidyl ester of maleinized dipentene modified with dibutyphosphate and methacrylic anhydride (MDDMD) was synthesized from industrial dipentene via Diels‐Alder reaction, glycidylation, epoxy ring‐opening reaction, and esterification. Its chemical structures were characterized by Fourier transform infrared (FTIR) analysis and proton nuclear magnetic resonance (¹H‐NMR). In order to improve its flexibility, we prepared a series of copolymers under UV light radiation by mixing it with certain proportions of poly(ethylene glycol) dimethacrylate‐200 (PEGDMA‐200) which contained flexible groups. Their tensile property, curing degrees (CD), hardness, limiting oxygen index (LOI), dynamic mechanical thermal properties, and thermostability were all investigated. The cured mixed resins have a relatively high tensile strength of 10.05 MPa and curing degrees up to 92.5%. Both hardness (range: 50 to 23 HD) and LOI (range: 22.8% to 24.4%) of cured resins are improved with the increase of MDDMD content. Dynamic mechanical analysis (DMA) shows that their glass transition temperatures rise with the increase of MDDMD content. Thermogravimetric analysis (TGA) shows that the thermal stability of cured resins is enhanced with the increase of PEGDMA‐200 content, as the main thermal initial decomposition temperatures are all above 260 °C and char yield at 800 °C are above 18.10%. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44084.     

Effect of the structure of curing agents modified by epoxidized oleic esters on the toughness of cured epoxy resins

The aim of this study was to determine the effect of the ester carbon chain length of curing agents modified by epoxidized oleic esters on the toughness of cured epoxy resins. An amine‐terminated prepolymer (i.e., curing agent G) was synthesized from a bisphenol A type liquid epoxy resin and triethylene tetramine. The toughening curing agents (G1 and G2) were prepared by reactions of epoxidized oleic methyl ester and epoxidized oleic capryl ester, respectively, with curing agent G. Fourier transform infrared spectrometry was used to characterize the chemical structure of the curing agents. The effects of the carbon chain length of the oleic ester group in the curing agents on the toughness and other performances of the curing epoxy resins were investigated by analysis of the Izod impact strength, tensile strength, elongation at break, thermal properties, and morphology of the fracture surfaces of the samples. The results denote that the toughness of the cured epoxy resins increased with the introduction of oleic esters into the curing agents without a loss of mechanical properties and that the toughness and thermal stability of the materials increased with increasing ester carbon chain length. The toughness enhancement was attributed to the flexibility of the end carbon chains and ester carbon chains of the oleic esters in the toughening curing agents. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011