Cationic photopolymerization of epoxy systems initiated by cyclopentadien-iron-biphenyl hexafluorophosphate ([Cp-Fe-biphenyl]+PF6 -)

Summary A study of the photoinitiated and thermally initiated cationic polymerizations of several epoxy systems with cyclopentadien-iron-biphenyl hexafluorophosphate ([Cp-Fe-biphenyl]⁺PF₆^-) photoinitiator has been conducted. [Cp-Fe-biphenyl]⁺PF₆^- photointitiator is capable of photoinitiating the cationic polymerization of glycidyl ether and cycloaliphatic epoxides directly on radiation with long-wavelength UV light. Compared with the mono-arene iron complexes, the photoinitiating activity of [Cp-Fe-biphenyl] PF₆ is higher than that of mono-arene iron complex I-261. When the photosensitizer benzoyl peroxide (BPO) is employed, [Cp-Fe-biphenyl]⁺PF₆^- is rendered much more efficient than diaryliodonium salt SR1012. The thermally initiated polymerization of epoxide / [Cp-Fe-biphenyl]⁺PF₆^- system was evaluated by DSC. It was found that the heat polymerization can occur in the systems of TDE85/[Cp-Fe-biphenyl]⁺PF₆^-without UV radiation at 71.6. However, the GCC/[Cp-Fe-biphenyl]⁺PF₆^- and ERL4221/[Cp-Fe-biphenyl]⁺PF₆^- systems are stable under 200^°. The dark-cure of the system of epoxides/[Cp-Fe-biphenyl]⁺PF₆^- after UV radiation is obvious by DSC measure.     

［环戊二烯-铁-二苯甲烷］六氟磷酸盐的光催化研究

芳茂铁盐是一类有效的用于环氧聚合的光引发剂。通过二茂铁和二苯甲烷的配体交换反应,制备了新型的芳茂铁盐［环戊二烯-铁-二苯甲烷］六氟磷酸盐（［Cp-Fe-Bp］⁺PF₆^-）。研究了其紫外－可见吸收性能和光解,发现［Cp-Fe-Bp］⁺PF₆^-）由d-d跃迁产生的在300 nm以上的吸收使其适合长波紫外光源。通过实时红外研究了［Cp-Fe-Bp］⁺PF₆^-）的光引发活性,表明能有效地引发3,4-环氧基环己基甲酸-3′4′-环氧基环己基甲酯（ERL-4221）开环聚合,过氧化苯甲酰能使其光引发活性显著提高。     

Flame retardancy effects of phosphorus‐containing compounds and cationic photoinitiators on photopolymerized cycloaliphatic epoxy resins

This study presents a promising ultraviolet (UV)‐curable epoxy resin formulation with improved flame‐retardant properties. The formulation is based on the cycloaliphatic epoxide 3,4‐epoxycyclohexylmethyl‐3,4‐epoxycyclohexane carboxylate (ERL4221) and a novel silicon, phosphorous containing flame‐retardant additive. The additive, 1,3,5,7‐tetramethyl‐1,3,5,7‐tetra 2‐(6‐oxido‐6‐H‐dibenzo(c,e) (1,2)oxaphosphorin‐6‐yl) ethylcyclotetrasiloxane (DOPO‐SiD), was synthesized by the addition reaction of 1,3,5,7‐tetramethyl‐1,3,5,7‐tetravinylcyclotetrasiloxane (D₄Vi) with 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO). Formulations containing the cycloaliphatic epoxy resin ERL4221 and the flame‐retardant DOPO‐SiD additive were prepared in various concentrations and crosslinked by UV irradiation. The effects of DOPO‐SiD and photoinitiators, such as the cyclopentadienyl iron complex of carbazole (In‐Fe) and diphenyl‐(4‐(phenylthiol) phenyl) sulfonium hexafluorophosphate (In‐S), on the flame‐retardant properties and thermal stabilities of UV‐cured ERL4221/DOPO‐SiD composites were investigated with limiting oxygen index, UL‐94 vertical test, and thermogravimetric analysis, respectively. The results showed that DOPO‐SiD can increase the thermal stabilities of the ERL4221/DOPO‐SiD. The char yield was improved when DOPO‐SiD and In‐Fe were simultaneously used. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40011.     

Visible light curing of bisphenol-A epoxides and acrylates photoinitiated by (η6-benzophenone)(η5-cyclopentadienyl) iron hexafluorophosphate

Visible light curing of diglycidyl ether of bisphenol-A (DGEBA) epoxy oligomer and acrylate monomers photoinitiated by (η⁶-benzophenone)(η⁵-cyclopentadienyl) iron hexafluorophosphate (Fc-BP) under a halogen lamp were studied by near infrared spectroscopy. Fc-BP exhibited high efficiency in the radical photopolymerization of acrylate monomers, even without the presence of tertiary amines. Under the same light source, however, benzophenone did not show any photoinitiating ability. Fc-BP could also be used to photoinitiate the cationic polymerization of DGEBA. There was an obvious increase in the photopolymerization rate of DGEBA and a decrease in the induction period when benzoyl peroxide was used as a photosensitizer. The induction period at the beginning of DGEBA cationic polymerization was eliminated by introducing a certain amount of cycloaliphatic epoxy monomer ERL4221 as an active diluent. However, the final epoxy conversion was decreased when ERL4221 was used.     

Synthesis and photoactivity of novel cationic photoinitiators: (η-Diphenylmethane) (η-cyclopentadienyl) iron hexafluorophosphate and (η-benzophenone) (η-cyclopentadienyl) iron hexafluorophosphate

Two novel cationic photoinitiators (η⁶-diphenylmethane) (η⁵-cyclopentadienyl) iron hexafluorophosphate (PhCH₂PhFe⁺CpPF₆⁻) and (η⁶-benzophenone) (η⁵-cyclopentadienyl) iron hexafluorophosphate (PhCOPhFe⁺CpPF₆⁻), were synthesized, characterized, and studied. PhCH₂PhFe⁺CpPF₆⁻ was prepared by straightforward synthetic techniques with ferrocene and diphenylmethane and PhCOPhFe⁺CpPF₆⁻ was synthesized from oxidation of diphenylmethane–cyclopentadienyliron salt. Their activity as cationic photoinitiators was studied using real-time infrared spectroscopy. The results obtained showed that PhCH₂PhFe⁺CpPF₆⁻ and PhCOPhFe⁺CpPF₆⁻ are capable of photoinitiating the cationic polymerization of epoxy monomer directly on irradiation with long-wavelength UV light. Comparative studies also demonstrated that PhCH₂PhFe⁺CpPF₆⁻ exhibited better efficiency than I-261 and PhCOPhFe⁺CpPF₆⁻. DSC studies showed that PhCOPhFe⁺CpPF₆⁻ and PhCH₂PhFe⁺CpPF₆⁻ photoinitiators in epoxides possess good thermal stability in the absence of light.     

Carbazole‐bound ferrocenium salt as an efficient cationic photoinitiator for epoxy polymerization

The low absorption of cyclopentadienyl‐Fe‐cumene hexafluorophosphate (I‐261) above 300 nm limits its utilization of longer wavelength emission from light sources. We report here the synthesis and photoactivity of a carbazole‐bound ferrocenium salt, cyclopentadienyl‐Fe‐carbazole hexafluorophosphate ([Cp‐Fe‐carbazole]⁺PF₆^?), which efficiently absorbs radiation between 300 and 400 nm. Its photoactivity is higher than that of I‐261 as a cationic photoinitiator. When the photosensitizer benzoyl peroxide (BPO) is employed, [Cp‐Fe‐carbazole]⁺PF₆^? can obviously be sensitized. Two other ferrocenium salts with amine groups, cyclopentadienyl‐Fe‐aniline hexafluorophosphate ([Cp‐Fe‐aniline]⁺PF₆^?) and cyclopentadienyl‐Fe‐p‐methylaniline hexafluorophosphate ([Cp‐Fe‐p‐methylaniline]⁺PF₆^?) were also studied. As photoinitiators, they perform poorly and can not be sensitized by BPO. Copyright © 2005 Society of Chemical Industry     

Ruthenium‐Catalyzed O‐Allylation of Phenols from Allylic Chlorides via Cationic [Cp*(η3‐allyl)(MeCN)RuX][PF6] Complexes

The [Cp*(MeCN)₃Ru(II)][PF₆] complex is an efficient catalyst precursor for the O‐allylation of phenols with allylic chlorides in the presence of K₂CO₃ under mild conditions. This ruthenium precursor affords branched allyl aryl ethers according to a regioselective reaction, which contrasts with the uncatalyzed nucleophilic substitution from the same substrates. Stable (η³‐allyl)Ru(IV) cationic complexes resulting from the reaction of [Cp*(MeCN)₃Ru][PF₆] with allylic halides were identified as intermediate catalytic species. An X‐ray structure determination of the complex [Cp*(MeCHCHCH₂)(MeCN)RuBr][PF₆] disclosed an (endo‐trans‐MeCHCHCH₂) allylic ligand. The structural information obtained from the study of Cp*(allyl)Ru(IV) complexes indicated that electronic effects at the coordinated allylic ligand likely account for the better regioselectivity obtained from cinnamyl chloride as compared to aliphatic allylic chlorides.     

An investigation into the degree and rate of polymerization of poly(methyl methacrylate) in the ionic liquid 1‐butyl‐3‐methylimidazolium hexafluorophosphate

Room‐temperature ionic liquids (ILs), including 1‐butyl‐3‐methylimidazolium hexafluorophosphate, [bmim⁺][PF₆^?], were investigated as replacements for volatile organic compounds in the free‐radical solution polymerization of poly(methyl methacrylate) (PMMA). The latter was synthesized in benzene and [bmim⁺][PF₆^?] at 70 °C via a free‐radical process and the degree and rate of polymerization were compared based on the solvent used. The degree of polymerization was found to be five times higher in [bmim⁺][PF₆^?] than in benzene, while the rate of reaction was approximately four times faster in [bmim⁺][PF₆^?]. The results indicate the potential for using ILs to produce high‐molecular‐weight polymers and block structures based on the increased free‐radical stability in ILs. Copyright © 2004 Society of Chemical Industry     

(Cyclopentadienyl)ruthenium‐Catalyzed Regio‐ and Enantioselective Decarboxylative Allylic Etherification of Allyl Aryl and Alkyl Carbonates

(Cyclopentadienyl)tris(acetonitrile)ruthenium hexafluorophosphate {[CpRu(NCMe)₃][PF₆]} or (cyclopentadienyl)(η⁶‐naphthalene)ruthenium hexafluorophosphate {[CpRu(η⁶‐naphthalene)][PF₆]} in combination with a pyridine oxazoline ligand efficiently catalyze the decarboxylative allylic rearrangement of allyl aryl carbonates. Good levels of regio‐ and enantioselectivity are obtained. Starting from enantioenriched secondary carbonates, the reaction is stereospecific and the corresponding allylic ethers are obtained with net retention of configuration. An intermolecular version of this transformation was also developed using allyl alkyl carbonates as substrates. Conditions were found to obtain the corresponding products with similar selectivity as in the intramolecular process. Through the use of a hemi‐labile hexacoordinated phosphate counterion, a zwitterionic air‐ and moisture‐stable chiral ruthenium complex was synthesized and used in the enantioselective etherification reactions. This highly lipophilic metal complex can be recovered and efficiently reused in subsequent catalysis runs.     

Ruthenium(II)‐Catalyzed Regioselective Synthesis of Allyl Ketones from Alkynes and their Silver(I)‐Catalyzed Hydroarylation into γ‐Functionalized Ketones

The regioselective synthesis of β,γ‐unsaturated ketones from terminal alkynes is achieved by cooperative action of tris(acetonitrile)pentamethylcyclopentadieneruthenium hexafluorophosphate [Cp*Ru(NCMe)₃⁺ PF₆⁻] and para‐toluenesulfonic acid catalysts. These allyl ketones undergo direct regioselective hydroarylation/Friedel–Crafts reaction to introduce an electron‐rich aryl group at the γ‐position in the presence of ligand‐free silver triflate (AgOTf) catalyst. Both catalytic reactions take place with atom economy and provide an alternative to the synthesis of a variety of allyl ketones and γ‐arylated ketones.     

Effect of ionic liquids on the structural,thermal, and in vitro degradation properties of poly(ε‐caprolactone) synthesized in the presence of Candida antarctica lipase B

The study provides detailed information on the differences in the structural, thermal and degradation properties of poly(ε‐caprolactone) synthesized in two different ionic liquids, 1‐butyl‐3‐methylimidazolium hexafluorophosphate [bmim][PF₆] and 1‐butyl‐3‐methylimidazolium bis(trifluoromethylsulfonyl)imide [bmim][NTf₂], regarding its further usage in the pharmaceutical field. The polymer structure confirms the presence of both linear polymer chains with end‐functional hydroxyl groups allowing covalent coupling of the therapeutic agents, and cyclic macromolecules, both affecting the degree of crystallinity of polymer. The highest macrocyclic content (64%) after 7 days of polymerization at 80 °C was observed for [bmim][NTf₂]. For [bmim][PF₆], the macrocyclic content value was not dependent on the reaction time and remained at a similar level (10–14% at 80 °C). The results of degradation test revealed that hydrolytic degradation of ester bonds is more pronounced for PCLs synthesized in [bmim][NTf₂], due to their lower degree of crystallinity compared with PCLs obtained in [bmim][PF₆]. A high purity, low polydispersity index of the obtained polymers and high yield of the process (ca., 90%) indicate that ionic liquids seem to be promising solvents for the synthesis of biomedical polymers. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43728.     

Synthesis,cationic polymerization and curing reaction with epoxy resin of 3,9‐di(p‐methoxybenzyl)‐1,5,7,11‐tetra‐oxaspiro(5,5)undecane

A new spiro ortho carbonate, 3,9‐di(p‐methoxybenzyl)‐1,5,7,11‐tetra‐oxaspiro(5,5)undecane was prepared by the reaction of 2‐methoxybenzyl‐1,3‐propanediol with di(n‐butyl)tin oxide, following with carbon disulfide. Its cationic polymerization was carried out in dichloromethane using BF₃‐OEt₂ as catalyst. The [¹H], [¹³C]NMR and IR data as well as elementary analysis of the polymers obtained indicated that it underwent double ring‐opening polymerization. The polymerization mechanism is discussed. The curing reaction of bisphenol A type epoxy resin in the presence of the monomer and a curing agent was investigated. DSC measurements were used to follow the curing process. In the case of boron trifluoride‐o‐phenylenediamine (BF₃‐OPDA) as curing agent, two peaks were found on the DSC curves, one of which was attributed to the polymerization of the epoxy group, and the other to the copolymerization of the monomer with the isolated epoxy groups or homopolymerization. However, when BF₃‐H₂NEt was used as curing agent, only one peak was present. IR measurement of the modified epoxy resin with various weight ratios of epoxy resin/monomer was performed in the presence of BF₃‐H₂NEt as curing agent. The results demonstrate that the conversion of epoxy group increases as the content of monomer increases. The curing process and the structure of the epoxy resin network are discussed. © 2000 Society of Chemical Industry     

Improved activity and stability of pseudomonas capaci lipase in a novel biocompatible ionic liquid, 1‐isobutyl‐3‐methylimidazolium hexafluorophosphate

BACKGROUND: Enzymes may exhibit enhanced activity, stability and selectivity in ionic liquids, depending on the properties of the liquid. The physical–chemical properties of ionic liquids, however, may be modified by altering the anion or cation in the ionic liquid. This feature is a key factor for realizing successful reactions. In this work, a new ionic liquid, 1‐isobutyl‐3‐methylimidazolium hexafluorophosphate (abbreviated as [i‐C₄mim][PF₆]), was synthesized and investigated as a novel medium for the transesterification reaction of 2‐phenylethanol with vinyl acetate catalyzed by pseudomonas capaci lipase. As contrasts, the reaction was also carried out in two reference solvents; the isomeric ionic liquid [i‐C₄mim][PF₆], 1‐butyl‐3‐methylimidazolium hexafluorophosphate (abbreviated as [C₄mim][PF₆]), and hexanes. RESULTS: As reaction medium, [i‐C₄mim][PF₆] was best among the three solvents. The initial reaction rate, the equilibrium conversion of 2‐phenylethanol and the half‐lifetime of the lipase in [i‐C₄mim][PF₆] medium were about 1.5, 1.2 and 3‐fold that obtained in [C₄mim][PF₆] medium, respectively. The lipase in [i‐C₄mim][PF₆] medium was recycled 10 times without substantial diminution in activity. CONCLUSION: The ionic liquid [i‐C₄mim][PF₆] has good biocompatibility, and can be used widely as green media in various biocatalysis reactions to improve the activity and stability of enzymes. Besides hydrophobicity and nucleophilicity, the spatial configuration of ionic liquids is also considered a key factor effecting the behaviour of the enzyme in ionic liquids. Copyright © 2008 Society of Chemical Industry     

Ethylene/1‐octadecene copolymerization using [η5:η1‐C5Me4‐4‐R1‐6‐R‐C6H2O]TiCl2 catalysts

Copolymerization of ethylene with 1‐octadecene was studied using [η⁵:η¹‐C₅Me₄‐4‐R₁‐6‐R‐C₆H₂O]TiCl₂ [R₁ = ^tBu (1), H (2, 3, 4); R = ^tBu (1, 2), Me (3), Ph (4)] as catalysts in the presence of Al(i‐Bu)₃ and [Ph₃C][B(C₆F₅)₄]. The effect of the concentration of comonomer in the feed and Al/Ti molar ratio on the catalytic activity and molecular weight of the resultant copolymer were investigated. The substituents on the phenyl ring of the ligand affect considerably both the catalytic activity and comonomer incorporation. The 1 /Al(i‐Bu)₃/[Ph₃C][B(C₆F₅)₄] catalyst system exhibits the highest catalytic activity and produces copolymers with the highest molecular weight, while the 2 /Al(i‐Bu)₃/[Ph₃C][B(C₆F₅)₄] catalyst system gives copolymers with the highest comonomer incorporation under similar conditions. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

A novel ferrocenium salt as visible light photoinitiator for cationic and radical photopolymerization

A novel hybrid photoinitiator for visible light photopolymerization, (η⁶-3-benzoyl-4-chlorodiphenylamine) (η⁵-cyclopentadienyl) iron hexafluorophosphate (Fc-NBP), was synthesized and studied. Its absorption in the UV and visible light regions showed much stronger activity than those of either the commercialized cationic photoinitiator I-261 or the conventional free radical photoinitiator benzophenone, especially above wavelengths of 350 nm. When exposed to visible light, the photoinitiator under study initiates both cationic polymerization and radical polymerization. The photoinitiator's abilities in the photopolymerization of acrylates and epoxides were evaluated by near infrared (NIR) spectroscopy. The results from NIR clearly indicate that Fc-NBP exhibited high efficiency in photopolymerizing acrylate monomers. In the same lamp, however, benzophenone showed no photoinitiating ability. The photopolymerization rate of the diglycidyl ether of the bisphenol-A epoxy (DGEBA) oligomer was found to be slower than that of acrylates when using Fc-NBP as the photoinitiator. This study shows that the polymerization of epoxide DGEBA can be speeded up by adding a photosensitizer benzoyl peroxide (BPO), but BPO and tertiary amines do not affect the free radical photopolymerization of tripropylene glycol diacrylate (TPGDA). We conclude by providing a possible photoinitiation mechanism.     

Mechanistic in situ High‐Pressure NMR Studies of Benzene Hydrogenation by Supramolecular Cluster Catalysis with [(η6‐C6H6)(η6‐C6Me6)2Ru3(μ3‐O)(μ2‐OH)(μ2‐H)2][BF4]

In situ high‐pressure NMR spectroscopy of the hydrogenation of benzene to give cyclohexane, catalysed by the cluster cation [(η⁶‐C₆H₆) (η⁶‐C₆Me₆)₂Ru₃(μ₃‐O)(μ₂‐OH)(μ₂‐H)₂]⁺ 2 , supports a mechanism involving a supramolecular host‐guest complex of the substrate molecule in the hydrophobic pocket of the intact cluster molecule.     

Electrochemical and optical properties of dicyclohexylmethyl substituted poly(3,4‐propylenedioxythiophene) analogue

An analogue of disubstituted 3,4‐propylenedioxythiophenes, namely 3,3‐bis(cyclohexylmethyl)‐3,4‐dihydro‐2H‐thieno[3,4‐b][1,4]dioxepin (ProDOT‐CycHex₂), was synthesized and its electrochemical polymerization was carried out successfully in an electrolyte solution of 0.1 M tetrabutylammonium hexafluorophosphate dissolved in a mixture of acetonitrile and dichloromethane (3/1: v/v). The corresponding polymer called PProDOT‐CycHex₂ has a reduced band gap of 1.85 eV and an electrochromic property: blue/violet when neutralized and highly transparent when oxidized. Also, PProDOT‐CycHex₂ film exhibited faster response time (0.7 s) and higher coloration efficiency (769 cm²/C) during oxidation when compared to its benzyl substituted analogue. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46214.     

Synthesis of new crosslinked porous ammonium‐based poly(ionic liquid) and application in CO2 adsorption

A new poly(ionic liquid) of N,N‐methylenebisacrylamide (MBA)‐crosslinked‐poly(4‐vinylbenzyltriethylammonium hexafluorophosphate)(MBA‐crosslinked‐P[VBTEA][PF₆]) is prepared through the ion exchange of KPF₆ with the precursor of MBA‐crosslinked‐P[VBTEA][Cl]; the precursor is synthesized by 4‐vinylbenzyltriethylammonium chloride and MBA via inverse suspension polymerization. MBA‐crosslinked‐P[VBTEA][PF₆] is a thermally stable (decomposes at nearly 300°C) and porous (apparent porosity of 64.3% and specific surface of 39.12 m²/g) polymer particle with high purity, as indicated by Fourier transformed infrared, energy dispersive spectroscopy, thermogravimetric, scanning electron microscopy, and porous analyses. It is observed that MBA‐crosslinked‐P[VBTEA][PF₆] has good CO₂ adsorption capability of 14.04 mg/g at 0.2 MPa and 25°C, and can be recovered by desorption at vacuum and 80°C, and reused with 99% CO₂ adsorption after four cycles. POLYM. ENG. SCI., 54:59–63, 2014. © 2013 Society of Plastics Engineers     

Three‐Component One‐Pot Synthesis of α‐Hydroxylamino Phosphonates using Ionic Liquids

α‐Hydroxylamino phosphonates are synthesised in a one‐pot operation by three‐component coupling reactions of aldehydes, hydroxylamines and diethyl phosphite using 1‐butyl‐3‐methylimidazolium tetrafluoroborate ([bmim]BF₄) or 1‐butyl‐3‐methylimidazolium hexafluorophosphate ([bmim]PF₆) ionic liquids under mild and neutral conditions. The recovered ionic liquids can be recycled for four to five runs without loss of activity.     

Asymmetric 1,3‐Dipolar Cycloaddition Reaction between α,β‐Unsaturated Aldehydes and Nitrones Catalyzed by Well‐Defined Iridium or Rhodium Catalysts

Reaction of the complexes (S_M,R_C)‐[(η⁵‐C₅Me₅)M{(R)‐Prophos}(H₂O)](SbF₆)₂ (M=Rh, Ir) with α,β‐unsaturated aldehydes diastereoselectively gave complexes (S_M,R_C)‐[(η⁵‐C₅Me₅)M{(R)‐Prophos}(enal)](SbF₆)₂ which have been fully characterized, including an X‐ray molecular structure determination of the complex (S_Rh,R_C)‐[(η⁵‐C₅Me₅)Rh{(R)‐Prophos}(trans‐2‐methyl‐2‐pentenal)](SbF₆)₂. These enal complexes efficiently catalyze the enantioselective 1,3‐dipolar cycloaddition of the nitrones N‐benzylideneaniline N‐oxide and 3,4‐dihydroisoquinoline N‐oxide to the corresponding enals. Reactions occur with excellent regioselectivity, perfect endo selectivity and with enantiomeric excesses up to 94 %. The absolute configuration of the adduct 5‐methyl‐2,3‐diphenylisoxazolidine‐4‐carboxaldehyde was determined through its (R)‐(−)‐α‐methylbenzylamine derivative.