Structural characterization of layered LiNi0.85−xMnxCo0.15O2 with x = 0, 0.1, 0.2 and 0.4 oxide electrodes for Li batteries

We report the synthesis of LiNi_0.85−xCo_0.15Mn_xO₂ positive electrode materials from Ni_0.85−xCo_0.15Mn_x(OH)₂ and Li₂CO₃. XRD and XPS are used to study the effect of Mn-doping on the microstructures and oxidation states of the LiNi_0.85−xCo_0.15Mn_xO₂ materials. The analysis shows that Mn-doping promotes the formation of a single phase. With increasing substitution of Mn ions for Ni ions, the lattice parameter a decreases, while the lattice parameters c and c/a increase. XPS revealed that the oxidation states of Ni, Co and Mn in LiNi_0.85−xCo_0.15Mn_xO₂ compounds (where x = 0.1, 0.2 and 0.4) were +2/+3, +3 and +4. The substitution of Mn ions for Ni ions induces a decrease in the average oxidation state of Ni. Because the substitution of Mn for Ni ions is complex, the extent of the changes between the lattice parameter and L_M-O differ. The occupation of Ni in Li sites is affected by the ordering of Mn⁴⁺ with Ni²⁺ and Mn⁴⁺ with Li⁺.     

Studies on the power factor of (Ba,Sr)Co2+xRu4−xO11 compounds

We have prepared polycrystalline single-phase ACo_2+xRu_4−xO₁₁ (A = Sr, Ba; 0 ≤ x ≤ 0.5) using the ceramic method and we have studied their structure, electrical resistivity and Seebeck coefficient, in order to estimate their power factor (P.F.). These layered compounds show values of electrical resistivity of the order of 10⁻⁵ Ωm and their Seebeck coefficients are positive and range from 1 μV K⁻¹ (T = 100 K) to 20 μV K⁻¹ (T = 450 K). The maximum power factor at room temperature is displayed by BaCo₂Ru₄O₁₁ (P.F.: 0.20 μW K⁻² cm⁻¹), value that is comparable to that shown by compounds such as SrRuO₃ and Sr₆Co₅O₁₅.     

Synthesis and electrochemical performance of Li(Ni0.8Co0.15Al0.05)0.8(Ni0.5Mn0.5)0.2O2 with core-shell structure as cathode material for Li-ion batteries

The core-shell structure cathode material Li(Ni_0.8Co_0.15Al_0.05)_0.8(Ni_0.5Mn_0.5)_0.2O₂ (LNCANMO) was synthesized via a co-precipitation method. Its applicability as a cathode material for lithium ion batteries was investigated. The core-shell particle consists of LiNi_0.8Co_0.15Al_0.05O₂ (LNCAO) as the core and a LiNi_0.5Mn_0.5O₂ as the shell. The thickness of the LiNi_0.5Mn_0.5O₂ layer is approximately 1.25 μm, as estimated by field emission scanning electron microscopy (FE-SEM). The cycling behavior between 2.8 and 4.3 V at a current rate of 18 mA g⁻¹ shows a reversible capacity of about 195 mAh g⁻¹ with little capacity loss after 50 cycles. High-rate capability testing shows that even at a rate of 5 C, a stable capacity of approximately 127 mAh g⁻¹ is retained. In contrast, the capacity of LNCAO rapidly decreases in cyclic and high rate tests. The observed higher current rate capability and cycle stability of LNCANMO can be attributed to the lower impedance including charge transfer resistance and surface film resistance. Differential scanning calorimetry (DSC) indicates that LNCANMO had a much improved oxygen evolution onset temperature of approximately 251 °C, and a much lower level of exothermic-heat release compared to LNCAO. The improved thermal stability of the LNCANMO can be ascribed to the thermally stable outer shell of LiNi_0.5Mn_0.5O₂, which suppresses oxygen release from the host lattice and not directly come into contact with the electrolyte solution. In particular, LNCANMO is shown to exhibit improved electrochemical performance and is a safe material for use as an electrode for lithium ion batteries.     

Enhancement microwave dielectric properties of La(Mg0.5Sn0.5)O3 ceramics by substituting Mg with Ni

The microwave dielectric properties of La(Mg_0.5−xNi_xSn_0.5)O₃ ceramics were examined with a view to their exploitation for mobile communication. The La(Mg_0.5−xNi_xSn_0.5)O₃ ceramics were prepared by the conventional solid-state method at various sintering temperatures. The X-ray diffraction patterns of the La(Mg_0.4Ni_0.1Sn_0.5)O₃ ceramics revealed no significant variation of phase with sintering temperatures. Apparent density of 6.71 g/cm³, dielectric constant (?_r) of 20.19, quality factor (Q × f) of 74,600 GHz, and temperature coefficient of resonant frequency (τ_f) of −85 ppm/°C were obtained for La(Mg_0.4Ni_0.1Sn_0.5)O₃ ceramics that were sintered at 1550 °C for 4 h.     

Relationships between Zr substitution for Ti and microwave dielectric properties in Mg(ZrxTi1−x)O3 ceramics

The influence of Zr substitution for Ti on the microwave dielectric properties and microstructures of the Mg(Zr_xTi_1−x)O₃(MZ_xT) (0.01 ≤ x ≤ 0.3) ceramics was investigated. The quality factors of Mg(Zr_xTi_1−x)O₃ ceramics with x = 0.01-0.05 were improved because the solid solution of a small amount of Zr⁴⁺ substitution in the B-site could increase density and grain size. An excess of Zr⁴⁺ resulted in the formation of a great deal of secondary phase that declined the microwave dielectric properties of MZ_xT ceramics. The temperature coefficient of resonant frequency (τ_f) of Mg(Zr_xTi_1−x)O₃ ceramics slightly increased with increasing Zr content, and the variation in τ_f was attributed to the formation of secondary phases.     

Preparation, structure and electrical conductivity of the pyrochlore-type phase Sm2Zr2O7 codoped with bivalent magnesium and trivalent dysprosium cations

The pyrochlore-type phases with the compositions of SmDy_1−xMg_xZr₂O_7−x/2 (0 ≤ x ≤ 0.20) have been prepared by pressureless-sintering method for the first time as possible solid electrolytes. The structure and electrical conductivity of SmDy_1−xMg_xZr₂O_7−x/2 ceramics have been studied by the X-ray diffraction (XRD), scanning electron microscopy (SEM) and impedance spectroscopy measurements. SmDy_1−xMg_xZr₂O_7−x/2 (x = 0, 0.05, 0.10) ceramics exhibit a single phase of pyrochlore-type structure, and SmDy_1−xMg_xZr₂O_7−x/2 (x = 0.15, 0.20) ceramics consist of pyrochlore phase and a small amount of the second phase magnesia. The total conductivity of SmDy_1−xMg_xZr₂O_7−x/2 ceramics obeys the Arrhenius relation, and the total conductivity of each composition increases with increasing temperature from 673 to 1173 K. SmDy_1−xMg_xZr₂O_7−x/2 ceramics are oxide-ion conductors in the oxygen partial pressure range of 1.0 × 10⁻⁴ to 1.0 atm at all test temperature levels. The highest total conductivity value is about 8 × 10⁻³ S cm⁻¹ at 1173 K for SmDy_1−xMg_xZr₂O_7−x/2 ceramics.     

Resistivity, thermopower, and thermal conductivity of nickel doped compounds Cr1−xNixSb2 at low temperatures

Substitutional compounds Cr_1−xNi_xSb₂ (0 ≤ x ≤ 0.1) were synthesized, and the effect of Ni substitution on transport and thermoelectric properties of Cr_1−xNi_xSb₂ were investigated at the temperatures from 7 to 310 K. The results indicated that the magnitudes of the resistivity and thermopower of Cr_1−xNi_xSb₂ decreased greatly with increasing Ni content at low temperatures, owing to an increase in electron concentration caused by Ni substitution for Cr. Experiments also showed that the low-temperature lattice thermal conductivity of Cr_1−xNi_xSb₂ decreased substantially with increasing Ni content due to an enhancement of phonon scattering by the increased number of Ni atoms. As a result, the figure of merit, ZT, of lightly doped Cr_0.99Ni_0.01Sb₂ was improved at T > ∼230 K. Specifically, the ZT of Cr_0.99Ni_0.01Sb₂ at 310 K was approximately ∼29% larger than that of CrSb₂, indicating that thermoelectric properties of CrSb₂ can be improved by an appropriate substitution of Ni for Cr.     

Electrical properties of binder-free thick film BaYxBi1−xO3 NTC thermistors

The microstructure and electrical properties of BaY_xBi_1−xO₃ thick film negative temperature coefficient thermistors, fabricated by screen printing, were investigated. The sintered thick films were the single-phase solid solutions of the BaY_xBi_1−xO₃ compounds with a monoclinic structure. The added Y₂O₃ led to a significant decrease in the grain size of the thermistors. The resistivity and coefficient of temperature sensitivity for the BaY_xBi_1−xO₃ (0 ≤ x ≤ 0.15) thick film NTC thermistors decreased first with increasing x in the range of x < 0.04 and then increased with further increase in x.     

Thermoelectric properties of Bi2SexTe3−x prepared by Bridgman method

Bi₂Se_xTe_3−x crystals with various x values were grown by Bridgman method. The electrical conductivity, σ, was found to decrease with increasing Se content. The highest σ of 1.6 × 10⁵ S m⁻¹ at room temperature was reached at x = 0.12 with a growth rate of 0.8 mm h⁻¹. The Seebeck coefficient, S, was less dependent on Se content, all with positive values showing p-type characteristics, and the highest S was measured to be 240 μV K⁻¹ at x = 0.24. The lowest thermal conductivity, κ, was 0.7 W m⁻¹ K⁻¹ at x = 0.36. The electronic part of κ, κ_el, showed a decrease with increasing Se content, which implies that the hole concentration as the main carriers was reduced by the addition of Se. The highest dimensionless figure of merit, ZT, at room temperature was 1.2 at x = 0.36, which is attributed to the combination of a rather high electrical conductivity and Seebeck coefficient and low thermal conductivity.     

Fabrication and properties of p-type K doped Zn1−xMgxO thin film

A series of K doped Zn_1−xMg_xO thin films have been prepared by pulsed laser deposition (PLD). Hall-effect measurements indicate that the films exhibit stable p-type behavior with duration of at least six months. The band gap of the K doped Zn_1−xMg_xO films undergoes a blueshift due to the Mg incorporation. However, photoluminescence (PL) results reveal that the crystallinity decreased with the increasing of Mg content. The fabricated K doped p-type Zn_0.95Mg_0.05O thin film exhibits good electrical properties, with resistivity of 15.21 Ω cm and hole concentration of 5.54 × 10¹⁸ cm⁻³. Furthermore, a simple ZnO-based p-n heterojunction was prepared by deposition of a K-doped p-type Zn_0.95Mg_0.05O layer on Ga-doped n-type ZnO thin film with low resistivity. The p-n diode heterostructure exhibits typical rectification behavior of p-n junctions.     

Preparation and characterization of La1−xKxFeO3 (x = 0-1) by self-propagating high-temperature synthesis for use as soot combustion catalyst

This paper proposes La_1−xK_xFeO₃ prepared by self-propagating high-temperature synthesis (SHS) as an alternative to platinum catalysts for promoting diesel soot combustion. The catalytic property of eleven products SHSed with different substitution ratios of potassium (x = 0-1) was experimentally evaluated using a thermobalance. In the mass loss curves of the product, T₅₀ was defined as the temperature at which the weight of the reference soot decreases to half its initial weight. The BET specific surface area of SHSed La_1−xK_xFeO₃ depended on x strongly. All the products showed good oxidation catalytic activity. Despite having the smallest surface area (0.11 m²/g) among the obtained products, La_0.9K_0.1FeO₃ (x = 0.1) was found to be the best catalyst with the lowest T₅₀ (442 °C). T₅₀ of La_1−xK_xFeO₃ decreased with increasing x for x > 0.2. The products with x = 0.6 and 0.8 were the second-best catalysts in terms of their T₅₀. Moreover, average apparent activation energy of La_0.9K_0.1FeO₃ (x = 0.1) calculated by Friedman method using TG was as much as 61 kJ/mol lower than that of Pt/Al₂O₃ catalyst. In conclusion, potassium-substituted SHSed La_1−xK_xFeO₃ can be used as an alternative to Pt/Al₂O₃ for soot combustion.     

Magnetomechanical properties of epoxy-bonded Sm1−xNdxFe1.55 (0 ≤ x ≤ 0.56) pseudo-1-3 magnetostrictive particulate composites

Pseudo-1-3 magnetostrictive particulate composites consisting of light rare earth (Sm and Nd)-based magnetostrictive Sm_1−xNd_xFe_1.55 particles with the Nd content x of 0-0.56 and randomly distributed sizes of 10-180 μm embedded and aligned in a passive epoxy matrix are fabricated using the particulate volume fraction of 0.5. The quasistatic magnetomechanical properties of the composites are investigated and the results are compared with their monolithic alloys for various x. The composites exhibit similar qualitative trends in properties with the alloys for all x. The Sm_0.92Nd_0.08Fe_1.55 composite shows a large unsaturated magnetostriction λ of −530 ppm at 500 kA/m and a high piezomagnetic coefficient d₃₃ of −2.0 nm/A at 100 kA/m as a result of the magnetocrystalline anisotropy compensation between Sm³⁺ and Nd³⁺ ions in the Sm_0.92Nd_0.08Fe_1.55 alloy.     

CuIn1−xAlxS2 thin films prepared by sulfurization of metallic precursors

CuIn_1−xAl_xS₂ thin films (x = 0, 0.09, 0.27, 0.46, 0.64, 0.82 and 1) with thicknesses of approximately 1 μm were formed by the sulfurization of DC sputtered Cu-In-Al precursors. All samples were sulfurized in a graphite container for 90 min at 650 °C in a 150 kPa Ar + S atmosphere. Final films were studied via X-ray diffraction (XRD), scanning electron microscopy (SEM) and micro-Raman spectroscopy. It was found that all samples were polycrystalline in nature and their lattice parameters varied slightly nonlinearly from {a = 5.49 Å, c = 11.02 Å} for CuInS₂ to {a = 5.30 Å, c = 10.36 Å} for CuAlS₂. No unwanted phases such as Cu_2−xS or others were observed. Raman were recorded at a room temperature and the most intensive and dominant A₁ phonon frequency varied nonlinearly from 294 cm⁻¹ (CuInS₂) to 314 cm⁻¹ (CuAlS₂).     

The studies of phase relation, microstructure, magnetic transition, magnetocaloric effect in (Gd1−xErx)5Si1.7Ge2.3 compounds

The phase relation, microstructure, Curie temperatures (T_C), magnetic transition, and magnetocaloric effect of (Gd_1−xEr_x)₅Si_1.7Ge_2.3 (x = 0, 0.05, 0.1, 0.15, and 0.2) compounds prepared by arc-melting and then annealing at 1523 K (3 h) using purity Gd (99.9 wt.%) are investigated. The results of XRD patterns and SEM show that the main phases in those samples are mono-clinic Gd₅Si₂Ge₂ type structure. With increase of Er content from x = 0 to 0.2, the values of magnetic transition temperatures (T_C) decrease linearly from 228.7 K to 135.3 K. But the (Gd_1−xEr_x)₅Si_1.7Ge_2.3 compounds display large magnetic entropy near their transition temperatures in a magnetic field of 0-2 T. The maximum magnetic entropy change in (Gd_1−xEr_x)₅Si_1.7Ge_2.3 compounds are 24.56, 14.56, 16.84, 14.20, and 13.22 J/kg K⁻¹ with x = 0, 0.05, 0.1, 0.15, and 0.2, respectively.     

Preparation and electrical properties of perovskite ceramics in the system BaBi1−xSbxO3 (0 ≤ x ≤ 0.5)

The effect of the composition on the electrical properties of BaBi_1−xSb_xO₃ (0 ≤ x ≤ 0.5) negative temperature coefficient (NTC) thermistors was studied. Major phases present in the sintered bodies of BaBi_1−xSb_xO₃ (0 < x < 0.5) ceramics were BaBi_0.5Sb_0.5O₃ compounds with a rhombohedral structure and BaBiO₃ compounds with a monoclinal structure. Most pores were located in the grains of BaBiO₃ and BaBi_0.5Sb_0.5O₃ ceramics. It was apparent that the ρ₂₅ and B_25/85 constant of the thermistors increased with increasing Sb content.     

Effects of Na+ doping on crystalline structure and electrochemical performances of LiNi0.5Mn1.5O4 cathode material

Pristine LiNi_0.5Mn_1.5O₄ and Na-doped Li_0.95Na_0.05Ni_0.5Mn_1.5O₄ cathode materials were synthesized by a simple solid-state method. The effects of Na⁺ doping on the crystalline structure and electrochemical performance of LiNi_0.5Mn_1.5O₄ cathode material were systematically investigated. The samples were characterized by XRD, SEM, FT-IR, CV, EIS and galvanostatic charge/discharge tests. It is found that both pristine and Na-doped samples exhibit secondary agglomerates composed of well-defined octahedral primary particle, but Na⁺ doping decreases the primary particle size to certain extent. Na⁺ doping can effectively inhibit the formation of Li_xNi_1–xO impurity phase, enhance the Ni/Mn disordering degree, decrease the charge-transfer resistance and accelerate the lithium ion diffusion, which are conductive to the rate capability. However, the doped Na⁺ ions tend to occupy 8a Li sites, which forces equal amounts of Li⁺ ions to occupy 16d octahedral sites, making the spinel framework less stable, therefore the cycling stability is not improved obviously after Na⁺ doping.     

Thermoelectric properties of Cu1−xPtxFeO2 (0.0 ≤ x ≤ 0.05) delafossite-type transition oxide

The samples of Cu_1−xPt_xFeO₂ (0 ≤ x ≤ 0.05) delafossite were synthesized by solid state reaction method for studying thermoelectric properties. The properties of Seebeck coefficient, electrical conductivity and thermal conductivity were measured in the high temperature ranging from 300 to 960 K. The results of Seebeck coefficient, electrical conductivity and power factor were increased with increasing Pt substitution and temperature. The thermal conductivity was decreased from 5.8 to 3.5 W/mK with increasing the temperature from 300 to 960 K. An important results, the highest value of power factor and ZT is 2.0 × 10⁻⁴ W/mK² and 0.05, respectively, for x = 0.05 at 960 K.     

Porous Li4Ti5O12 anode material synthesized by one-step solid state method for electrochemical properties enhancement

A porous Li₄Ti₅O₁₂ anode material was successfully synthesized from mixture of LiCl and TiCl₄ with 70 wt% oxalic acid by a modified one-step solid state method. The anode material Li₄Ti₅O₁₂ exhibited a cubic spinel structure and only one voltage plateau occurred around 1.5 V. The initial capacity of porous Li₄Ti₅O₁₂ was 167 and 133 mAh g⁻¹ at 0.5 and 1C charge/discharge rate, respectively, and the capacity retention maintained above 98% after 200 cycles. The porous Li₄Ti₅O₁₂ structure showed promising rate performance with a capacity of 70 mAh g⁻¹ at charge/discharge 10C rate after 200 cycles. It was demonstrated that the porous structure could withstand 50C charge/discharge rate and exhibited excellent cycling stability.     

Cr3+掺杂LiNi0.5Mn1.5O4材料的制备及性能研究

采用高温固相法合成了Cr₃₊掺杂的LiNi_0.5Mn_1.5O₄正极材料,研究了掺杂量对材料物理性能和电化学性能的影响。利用XRD、SEM对材料的结构和形貌进行了表征,结果显示样品具有棱边清晰的尖晶石形貌。讨论了不同Cr₃₊掺杂量对LiCr_xNi_0.5-0.5xMn_1.5-0.5xO₄(x=0,0.05,0.1,0.15,0.2)正极材料性能的影响。充放电测试、循环伏安和交流阻抗测试结果表明：当Cr₃₊的掺杂量为x=0.1时(LiCr_0.1Ni_0.45Mn_1.45O₄)正极材料的性能最好,0.1C、0.5C、1C、2C及5C的首次放电比容量依次为131.54mAh g_-1、126.84mAh g_-1、121.28mAh g_-1、116.49mAh g_-1和96.82mAh g_-1,1C倍率下循环50次,容量保持率仍为96.5%。     

Synthesis and functional properties of the Ni1−xMnxFe2O4 ferrites

Nanocrystalline Ni_1−xMn_xFe₂O₄ (x = 0; 0.17; 0.34; 0.5) ferrite powders were successfully synthesized using the sol-gel combustion method, by using nitrates as cations source and citric acid (C₆H₈O₇) as combustion/chelating agent. The reaction advancement was observed by means of IR absorption spectroscopy, by monitoring two characteristic bands for the spinel compounds at about 600 cm⁻¹ and 400 cm⁻¹, respectively. The as-synthesized powders were characterized by IR spectroscopy, X-ray diffraction (XRD) and scanning electronic microscopy (SEM). The magnetic study shows that the saturation magnetization decreases with increasing the Mn addition, as result of the particle size reduction. The dielectric properties were measured as a function of frequency in the range of 10 Hz to 1 MHz. The real part of permittivity has values of ∼88 at 1 kHz and ∼7 at 1 Hz for x = 0. An increasing dielectric permittivity with increasing the amount of Mn is observed. For all the investigated compositions, both the real and imaginary parts of permittivity decrease with frequency.