共查询到20条相似文献,搜索用时 203 毫秒
1.
A. Deutschinger U. Schmid M. Schneider W. Brenner H. Wanzenböck B. Volland Tzv. Ivanov I. W. Rangelow 《Microsystem Technologies》2010,16(11):1901-1908
A micromachined electro-thermal gripper, first introduced by Ivanova et al. (Microelectron Eng 83:1393–1395, 2006), represents a promising candidate for the manipulation and handling of micro or even
nano-scaled objects. To further optimize the performance of the device, a detailed electrical and mechanical characterization
is needed. Due to the so-called duo-action gripper approach (i.e., a separate actuator for closing and opening action) these
investigations focused on the maximum (minimum) opening width being 11.5 μm (3.3 μm), while in rest position a value of 4 μm
is feasible. The maximum, electrical input power is limited to 80 mW/actuator element, resulting in a current density of up
to 1.27 MA cm−2 in the corresponding metal layers. When applying, however, larger current densities the probability of device failure increases
substantially as in combination with an enhanced temperature of about 200°C electromigration effects occur in the metallization.
Furthermore, the cut-off frequency and parasitic effects during actuation such as the z-deflection and the increase in length
of each arm both showing values of up to 3 μm have been investigated as a function of operation parameters. Finally, the tips
of the gripper were sharpened using Focused Ion Beam technique to a radius of less than 1 μm for gripping operations in space-restricted
environments or for the manipulation or handling of sub-μm scaled objects. 相似文献
2.
This paper presents a detail modeling, finite element analysis and testing results of MEMS based electrostatically actuated
microgripper. Interdigitated lateral comb pairs have been used to actuate the microgripper. The microgripper is optimized
using standard SOI-MUMPs technology in L-Edit of MEMS-Pro with dual jaws actuation at low voltages. Coupled electromechanical
finite element analysis performed in COVENTOR-WARE shows total displacement of 15.5 μm at jaws tip at 50 V, which is quite
comparable to experimental result of 17 μm displacement at the tip of gripper jaw for the same voltage. Micromanipulation
experiments have successfully demonstrated the gripping, holding micro-objects between 53 and 70 μm in size. The simulated
model is used to study detail profile of Von Mises stresses and deformations in the model. It is noted that maximum stress
in microgripper is 200 MPa which is much smaller than yield stress of 7 GPa. The slight difference between finite element
analysis and experimental results is because of small variations in process material parameters. The total size of gripper
is 5.03 × 6.5 mm2. 相似文献
3.
An integrated flow-cell for full sample stream control 总被引:1,自引:1,他引:0
In this study, we present a novel three-dimensional hydrodynamic sheath flow chip that allows full control of a sample stream.
The chip offers the possibility to steer each of the four side sheath flows individually. The design of the flow-cell exhibits
high flexibility in creating different sample stream profiles (width and height) and allows navigation of the sample stream
to every desired position inside the microchannel (vertical and horizontal). This can be used to bring the sample stream to
a sensing area for analysis, or to an area of actuation (e.g. for cell sorting). In addition, we studied the creation of very
small sample stream diameters. In microchannels (typically 25 × 40 μm2), we created sample stream diameters that were five
to ten times smaller than the channel dimensions, and the smallest measured sample stream width was 1.5 μm. Typical flow rates
are 0.5 μl/min for the sample flow and around 100 μl/min for the cumulated sheath flows. The planar microfabricated chip,
consisting of a silicon–glass sandwich with an intermediate SU-8 layer, is much smaller (6 × 9 mm2) than the previously presented
sheath flow devices, which makes it also cost-effective. We present the chip design, fluidic simulation results and experiments,
where the size, shape and position of the sample stream have been established by laser scanning confocal microscopy and dye
intensity analysis. 相似文献
4.
Chee Tiong Lim Hong Yee Low Johnson K. K. Ng Wen-Tso Liu Yong Zhang 《Microfluidics and nanofluidics》2009,7(5):721-726
A photolithography technique using SU-8 and PDMS was developed to fabricate three-dimensional hemispherical structures. This
technique utilized a mask-aligner and normal binary coded photomasks to generate hemispherical pits on SU-8, followed by PDMS
molding to obtain an array of dome-shaped structures. Using this technique, a microfluidic device was fabricated with a patterning
area that consisted of an array of 5 μm wells and dome-shaped structures with 10 μm diameter and 6 μm height. Encoded microbeads,
6 μm in size, were immobilized and patterned in the microfluidic device under flow conditions and a DNA hybridization experiment
was performed to demonstrate the incorporation of encoded beads that would enable a high level of multiplexing in bioassays. 相似文献
5.
This study presents a particle manipulation and separation technique based on dielectrophoresis principle by employing an
array of isosceles triangular microelectrodes on the bottom plate and a continuous electrode on the top plate. These electrodes
generate non-uniform electric fields transversely across the microchannel. The particles within the flowing fluid experience
a dielectrophoretic force perpendicular to the fluid flow direction due to the non-uniform electric fields. The isosceles
triangular microelectrodes were designed to continuously exert a small dielectrophoretic force on the particles. Particles
experiencing a larger dielectrophoretic force would move further in the perpendicular direction to the fluid flow as they
traveled past each microelectrode. Polystyrene microspheres were used as the model particles, with particles of ∅20 μm employed
for studying the basic characteristics of this technique. Particle separation was subsequently demonstrated on ∅10 and ∅15 μm
microspheres. Using an applied sinusoidal voltage of 20 Vpp and frequency of 1 MHz, a mean separation distance of 0.765 mm between them was achieved at a flow rate of 3 μl/min (~1 mm/s),
an important consideration for high throughput separation capability in a micro-scale technology device. This unique isosceles
triangular microelectrodes design allows heterogeneous particle populations to be separated into multiple streams in a single
continuous operation. 相似文献
6.
Results of the design, microfabrication and testing of a proof-of-concept, diaphragm-type silicone sealing joint are presented.
DRIE-etched cavities were filled with a flexible sealing element made of polydimethylsiloxane that supports a silicon piston.
A series of sealing joints were produced with variable widths, and the displacement of the piston was measured after applying
pressures of up to 1 bar above atmospheric pressure in 0.2 bar increments. Two masks were designed to produce several sets
of silicone springs with widths of 2–10.5 μm, each consisting of a 10 μm thick silicon piston that is 2 mm long. Tests performed
on the shear spring joints were found to give a displacement of 0.5 μm at 1 bar when the sealing width is 6 μm or more. The
sealing joint with a 10 μm width was found to give a displacement of 0.9 μm and an elastic recovery of 88%. The results showed
this type of joint in the form of an elastically-deforming seal provides sufficient displacement for propelling liquid droplets
as part of a liquid propulsion system. 相似文献
7.
This paper describes the design and fabrication of a guide block and micro probes, which were used for a vertical probe card
to test a chip with area-arrayed solder bumps. The size of the fabricated guide block was 10 mm × 6 mm. The guide block consisted
of 172 holes to insert micro probes, 2 guide holes for exact alignment, and 4 holes for bolting between the guide block and
the housing of a PCB. Pitch and size of the inserting holes were 80 μm, and 90 μm × 30 μm, respectively. A silicon on insulator
wafer was used as the substrate of the guide block to reduce micro probes insertion error. The micro probes were made of nickel–cobalt
(Ni–Co) alloy using an electroplating method. The length and thickness of the micro probes were 910 and 20 μm, respectively.
A vertical probe card assembled with the fabricated guide block and micro probes showed good x–y alignment and planarity errors within ±4 and ±3 μm, respectively. In addition, average leakage current and contact resistance
were approximately 0.35 nA and 0.378 ohm, respectively. The proposed guide block and micro probes can be applied to a vertical
probe card to test a chip with area-arrayed solder bumps. 相似文献
8.
Bin Ma Sheng Liu Zhiyin Gan Guojun Liu Xinxia Cai Honghai Zhang Zhigang Yang 《Microfluidics and nanofluidics》2006,2(5):417-423
Many of the compounds in drugs cannot be effectively delivered using current drug delivery techniques (e.g., pills and injections). Transdermal delivery is an attractive alternative, but it is limited by the extremely low permeability of the skin. As the primary barrier to transport is located in the upper tissue, Micro-Electro-Mechanical-System (MEMS) technology provides novel means, such as microneedle array and PZT pump, in order to increase permeability of human skin with efficiency, safety and painless delivery, and to decrease the size of the pump. Microneedle array has many advantages, including minimal trauma at penetration site because of the small size of the needle, free from condition limitations, painless drug delivery, and precise control of penetration depth. These will promote the development of biomedical sciences and technology and make medical devices more humanized. So far, most of the insulin pumps being used are mechanical pumps. We present the first development of this novel technology, which can assemble the PZT pump and the microneedle array together for diabetes mellitus. The microneedle array based on a flexible substrate can be mounted on non-planar surface or even on flexible objects such as a human fingers and arms. The PZT pump can pump the much more precision drug accurately than mechanical pump and the overall size is much smaller than those mechanical pumps. The hollow wall straight microneedle array is fabricated on a flexible silicon substrate by inductively coupled plasma (ICP) and anisotropic wet etching techniques. The fabricated hollow microneedles are 200 μm in length and 30 μm in diameter. The microneedle array, which is built with on-board fluid pumps, has potential applications in the chemical and biomedical fields for localized chemical analysis, programmable drug-delivery systems, and very small, precise fluids sampling. The microneedle array has been installed in an insulin pump for demonstration and a leak free packaging is introduced.The support from Ministry of Science and Technology of the People’s Republic of China with contract number of 2005AA40420. 相似文献
9.
Joong Yull Park Mina Morgan Aaron N. Sachs Julia Samorezov Ryan Teller Ye Shen Kenneth J. Pienta Shuichi Takayama 《Microfluidics and nanofluidics》2010,8(2):263-268
Conventional cell trapping methods using microwells with small dimensions (10–20 μm) are useful for examining the instantaneous
cell response to reagents; however, such wells have insufficient space for longer duration screening tests that require observation
of cell attachment and division. Here we describe a flow method that enables single cell trapping in microwells with dimensions
of 50 μm, a size sufficient to allow attachment and division of captured cells. Among various geometries tested, triangular
microwells were found to be most efficient for single cell trapping while providing ample space for cells to grow and spread.
An important trapping mechanism is the formation of fluid streamlines inside, rather than over, the microwells. A strong flow
recirculation occurs in the triangular microwell so that it efficiently catches cells. Once a cell is captured, the cell presence
in the microwell changes the flow pattern, thereby preventing trapping of other cells. About 62% of microwells were filled
with single cells after a 20 min loading procedure. Human prostate cancer cells (PC3) were used for validation of our system. 相似文献
10.
Peihong Wang Katsuhiko Tanaka Susumu Sugiyama Xuhan Dai Xiaolin Zhao Jingquan Liu 《Microsystem Technologies》2009,15(6):941-951
This paper presents a micro electromagnetic energy harvester which can convert low level vibration energy to electrical power.
It mainly consists of an electroplated copper planar spring, a permanent magnet and a copper planar coil with high aspect
ratio. Mechanical simulation shows that the natural frequency of the magnet-spring system is 94.5 Hz. The resonant vibration
amplitude of the magnet is 259.1 μm when the input vibration amplitude is 14 μm and the magnet-spring system is at resonance.
Electromagnetic simulation shows that the linewidth and the turns of the coil influence the induced voltage greatly. The optimized
electromagnetic vibration energy harvester can generate 0.7 μW of maximal output power with peak–peak voltage of 42.6 mV in
an input vibration frequency of 94.5 Hz and input acceleration of 4.94 m/s2 (this vibration is a kind of low level ambient vibration). A prototype (not optimized) has been fabricated using MEMS micromachining
technology. The testing results show that the prototype can generate induced voltage (peak–peak) of 18 mV and output power
of 0.61 μW for 14.9 m/s2 external acceleration at its resonant frequency of 55 Hz (this vibration is not in a low ambient vibration level). 相似文献
11.
Zhuoqing Yang Haogang Cai Guifu Ding Hong Wang Xiaolin Zhao 《Microsystem Technologies》2011,17(8):1329-1342
A novel contact-enhanced design of MEMS (micro-electro-mechanical system) inertial switch was proposed and modeled in Simulink?. The contact effect is improved by an easily realized modification on the traditional design, i.e. introducing a movable
contact point between the movable electrode (proof mass) and the stationary electrode, therefore forming a dual mass-spring
system. The focus of this paper is limited to a vertically driven unidirectional one for the purposes of demonstration, but
this design concept and Simulink? model is universal for various kinds of inertial micro-switches. The dynamic simulation confirmed the contact-enhancing mechanism,
showing that the switch-on time can be prolonged for the dynamic shock acceleration and the bouncing effect can be reduced
for the quasi-static acceleration. The threshold acceleration of the inertial switch is determined by the proof mass-spring
system’s natural frequency. Since the inertial switches were fabricated by the multilayer electroplating technology, the proof
mass thickness were assigned two values, 100 and 50 μm, in order to get threshold levels of 56 and 133 g respectively for
the dynamic acceleration of half-sine wave with 1 ms duration. Other factors that influence the dynamic response, such as
the squeeze film damping and the contact point-spring system’s natural frequency were also discussed. The fabricated devices
were characterized by the drop hammer experiment, and the results were in agreement with the simulation predictions. The switch-on
time was prolonged to over 50 μs from the traditional design’s 10 μs, and could reach as long as 120 μs. Finally, alternative
device configurations of the contact-enhancing mechanism were presented, including a laterally driven bidirectional inertial
switch and a multidirectional one. 相似文献
12.
This paper describes the design and fabrication of a MEMS guide plate, which was used for a vertical probe card to test a
wafer level packaged die wafer. The size of the fabricated MEMS guide plate was 10.6 × 10.6 cm. The MEMS guide plate consisted
of 8,192 holes to insert pogo pins, and four holes for bolting between the guide plate and the housing. To insert pogo pins
easily, an inclined plane was defined at the back of each hole. Pitch and diameter of the hole were 650 and 260 μm, respectively.
In order to define inserting holes and inclined planes at an exact position, silicon MEMS technology was used such as anisotropic
etching, deep reactive etching and more. Silicon was used as the material of the guide plate to reduce alignment mismatch
between the pogo pins and solder bumps during a high temperature testing. A combined probe card with the fabricated MEMS guide
plate showed good x–y alignment and planarity errors within ±9 and ±10 μm at room temperature, respectively. In addition, x–y alignment and planarity are ±20 and ±16 μm at 125°C, respectively. The proposed MEMS guide plate can be applied to a vertical
probe card for burn-in testing of a wafer level packaged die wafer because the thermal expansion coefficient of the MEMS guide
plate and die wafer is same. 相似文献
13.
Chien-Hsing Chen Tzu-Chien Tsao Wan-Yun Li Wei-Chih Shen Chung-Wei Cheng Jaw-Luen Tang Chun-Ping Jen Lai-Kwan Chau Wei-Te Wu 《Microsystem Technologies》2010,16(7):1207-1214
A novel fiber-optic localized plasma resonance (FO-LPR) sensor composed of a U-shape optical fiber was proposed and demonstrated
in this study. The U-shape optical fiber was fabricated by a femtosecond laser micromachining system. The dimensions of the
U-shape zone were 100 μm in depth measured from the surface of the polymer jacket layer, 80 μm in width in the jacket layer,
60 μm in width in the cladding layer. The total length is 5 mm. After laser annealing treatment, the average surface roughness
was 205.8 nm as determined by Atom Force Microscope (AFM). The exposed surface of the U-shape fiber was modified with self-assembled
gold nanoparticles to produce the FO-LPR sensor. The response of the sensor shows that the signal increases linearly with
increasing refractive index. The sensor resolution of the sensor was determined to be 1.06 × 10−3 RIU. 相似文献
14.
Sang Min Yi Byung Yun Joo Min Soo Park Chong Nam Chu Soo-Ik Oh 《Microsystem Technologies》2006,12(9):877-882
This study investigates the size limit of a hole produced by the conventional punching process. In the micron size hole punching, there are two main technical obstacles that complicate the miniaturization steps. One is the fabrication of the micro punch tools with high dimensional accuracy and the other is the accurate alignment of the tools within the die clearance of 1∼2 μm. In this study, we tried to mechanically punch a 15 μm size hole. For this, we fabricated and alignedthe punch tools. Micro punch tools made of tungsten carbide were fabricated by micro-electrical discharge machining (micro-EDM). The diameter of punch tip was 15 μm, and that of the die hole, 17 μm. With the developed micro punching system, tools were aligned, and then, 15 μm size holes were made on 13-μm-thick brass and stainless steel foil, respectively. 相似文献
15.
Lin Gui Bo Yang Yu Carolyn L. Ren Jan P. Huissoon 《Microfluidics and nanofluidics》2011,10(2):435-445
A phase change (PC) microvalve with an integrated two-level cooling/heating system is developed for microfluidic applications
in this article. This PC microvalve utilizes the liquid–solid PC of a small portion of the working medium in a microchannel
to switch on/off the flow in the microchannel. The size of the working medium for the PC microvalve is 5-mm long, 50-μm high,
and 80-μm wide (50 μm × 80 μm is the cross-sectional area of the channel) in this study. The switch is actuated by using a
two-level cooling/heating system integrated on the chip. The first-level cooling/heating unit keeps the working medium in
the valve area in the temperature range of supercooling state. Based on the supercooling state, the second-level cooling/heating
unit either heats up or cools down the medium in the valve area to trigger its PC between liquid and solid for valving purposes.
The proposed microfluidic PC microvalve is characterized experimentally in microfluidic chips. The thermal impact of one PC
microvalve in one particular microchannel on its adjacent channels is discussed by establishing a preliminary analytical model
and a numerical model. In addition to no leakage and no moving element, this PC microvalve with a two-level cooling/heating
system can achieve a very short cooling time (i.e., 2.72 s). 相似文献
16.
I. S. Akhatov J. M. Hoey O. F. Swenson D. L. Schulz 《Microfluidics and nanofluidics》2008,5(2):215-224
A micro-capillary system capable of generating a focused collimated aerosol beam (CAB) is demonstrated both theoretically
and experimentally. The approach is based on a manifestation of the Saffman force where high velocity (∼100 m/s) aerosol particles,
flowing through a micro-capillary (d ∼ 100 μm and l ∼ 1 cm), migrate perpendicular to the centerline of the capillary. Upon exiting the micro-capillary system, the particles
maintain momentum, and when the aerosol is comprised of solid-in-liquid dispersions such as Ag nanoparticle ink, the CAB approach
enables printing of advanced materials features with linewidth ≤ 10 μm. 相似文献
17.
The manipulation of picoliter droplets is demonstrated using optically induced microscale circulatory flows. The circulation
results from Marangoni effects induced by optical heating from light patterns created by a computer projector. Manipulation
of single droplets and parallel manipulation of multiple droplets are achieved with induced forces of up to 1 nN and an average
resolution of 146.5 μm. 相似文献
18.
Fabrication and analysis of the reflowed microlens arrays using JSR THB-130 N photoresist with different heat treatments 总被引:1,自引:0,他引:1
This paper reports that the fabrication of the reflowed microlens by the negative tone JSR THB-130 N photoresist can be treated
with different thermal treatments using hotplate and oven. The different disk or thin cylinder arrays with diameters of 40–70 μm
and thickness of about 7.4 μm were patterned using photolithography technology, and baked at 220°C by two kinds of thermal
treatments using hotplate and oven to form reflowed microlens arrays. The spot size of the refractive microlens was then measured
by optical microscopy and the total focal length of refractive microlens was simulated by curve fitting the lens profiles.
The resolution of the microlens arrays approaches to 400 dpi as coated with Hexamethyldisilizane material. The smallest spot
size of about 2.72 μm at the nominal 40 μm microlensis is obtained by the oven heat treatment, and the shortest total focal
length of about 150 μm at the nominal 40 μm microlens is achieved by the hotplate heat treatment. The reduced spot size and
total focal length of the microlens could improve the density and performance of optical devices and imaging systems. 相似文献
19.
Miniaturized interference filters were designed and fabricated using two different manufacturing technologies. Applying micromachined
ceramic masks during the coating processes interference filters with 1 mm lateral feature size and an alignment accuracy of
50 μm were arranged in an array consisting of three different filters. The filter edge definition obtained by this method
was smaller than 50 μm. By applying ion assisted deposition (IAD), a low-temperature coating process, the spectral sensitivity
of receiver cells has been modified by coating the cells directly. A combination of coating processes, microlithographic masking
procedures, and dry etching technologies made it possible to arrange three different stripe filters with minimum filter features
of about 5 μm side by side. The accuracy during mask alignment and the filter edge definition was also within 1 and 2 μm,
respectively.
Received: 20 March 1999/Accepted: 12 April 1999 相似文献
20.
《控制论与系统》2013,44(8):645-662
Recently robot manipulators have been expected to perform sophisticated tasks such as object manipulation, assembly tasks, or cooperative tasks with human workers. In order to realize these tasks with robot manipulators, it is important to understand the human strategy of object grasping and manipulation. In this study, we have examined how a human being decides the grasping force necessary to manipulate an unknown object in order to apply human object-grasping strategy for robotic systems. Experiments have been performed with several kinds of objects under several kinds of conditions to investigate how much grasping force human subjects generate. Adjustment strategy of human grasping force when the object is manipulated or in contact with an environment is also examined. Neural networks (the desired grasping force planner) that generate the humanlike desired grasping force are then designed for robotic systems. The effectiveness of the proposed desired grasping force planner is evaluated via experiments. 相似文献