Broadband high-efficiency circularly polarized active antenna and array for RF front-end application

This paper presents a broadband high-efficiency circularly polarized (CP) active integrated antenna, and a broadband CP active array at 2 GHz. To realize the broadband CP antenna, a circular patch is aperture coupled by crossed slots in the ground plane, which are fed by an L-shaped microstrip feed line below the ground. The antenna is designed to serve the functions of both a radiator and a harmonics-terminated load for class-E high-efficiency power-amplifier (PA) integration. The broadband CP active antenna is realized by directly integrating the broadband CP antenna with the class-E PA. It achieves a 9% bandwidth (1.84-2.01 GHz) for axial ratio (AR) below 3 dB, and a 12% bandwidth for power-added efficiency (PAE) over 60%. To form the broadband CP active array, four active antenna elements are sequentially rotated, and each element is directly integrated with broadband class-E PA. A low-cost printed-circuit-board technology is employed in fabrication and a pseudomorphic high electron-mobility transistor is used. A peak drain efficiency of 71.5% for the class-E amplifier is measured at 1.95 GHz. The active array achieves a peak-effective radiated power of 39.7 dBm, and PAE is over 50% within a 22.6% bandwidth (1.72-2.16 GHz). The AR is below 3 dB over a 27% bandwidth (1.72-2.26 GHz).     

Ka频段宽带圆极化微带天线

面向Ka频段高通量卫星对天线的需求,设计了一种Ka频段宽带圆极化微带天线. 天线单元主要由圆形辐射贴片和缝隙耦合馈电结构组成,通过两个类T形缝隙结合实现宽带圆极化. 天线仅有三层金属层,结构简单. 仿真结果显示,天线单元的相对阻抗带宽为31.5%（25.1～34.5 GHz）,相对3 dB轴比带宽为20.3%（26.5～32.5 GHz）. 由于单元尺寸较小,不便于对其性能进行验证,因此利用该天线单元组成2×2天线阵列,并进行加工测试. 仿真与试验结果表明,天线阵列阻抗带宽以及3 dB轴比带宽可以覆盖25.6～33.1 GHz频率范围,实测结果与仿真结果一致性良好.     

一种新型布局的圆极化微带天线阵优化设计

提出了一款高增益低副瓣新型圆极化微带天线阵。单元天线采用叠层切角圆极化微带结构,通过八边形边界布局和顺序旋转交叠组阵技术,实现了天线阵方向性图的对称性和圆极化辐射性能的最优化;馈电网络采用威尔金森功分器和最大平坦式阻抗变换器实现不等功分宽带阻抗匹配,通过改进馈电方向寻求对称结构,简化了馈电网络的设计。制作了天线阵实物并进行了测量。测试结果表明:天线在3.2~4.6 GHz频段内S₁₁<-10 dB,阻抗相对带宽36%;在3.8~4.5 GHz频段内顶点轴比小于3 dB,圆极化相对带宽17%;在4~4.4 GHz频段内天线增益均在15 dB以上,最高增益达17 dB。     

一种用于5G MIMO 系统的宽带高增益圆极化天线

为提升5G无线通信系统容量,设计了一款基于V 形缝隙耦合馈电的宽带高增益圆极化天线。该天线采用双层辐射贴片结构,拓展天线的阻抗带宽,并分别在辐射贴片和寄生贴片上刻蚀一对半径不等、位置正交的双圆形缝隙,有效改善了天线的圆极化特性。通过加载平板反射器提高天线的前后比,实现良好的定向辐射。实测结果表明,驻波比小于2的阻抗带宽为53.55% (2.27~3.93 GHz),在半功率波束宽度范围内轴比小于3 dB,轴比带宽为27.38%(2.9~3.82 GHz),在工作频带内实测的天线平均增益达到8.22 dBi。该天线适合作为5G多天线系统中的智能天线单元进行自适应波束赋形。     

A dual polarized aperture coupled circular patch antenna using a C-shaped coupling slot

The design and development of a dual linearly polarized aperture coupled circular microstrip patch antenna at C-band are presented. The antenna uses a novel configuration of symmetric and asymmetric coupling slots. Variations in isolation between orthogonal feedlines and antenna axial ratio with the position of coupling slots are studied and broadband isolation and axial ratio are achieved. The prototype antenna yields 7.6 dBi peak gain, 70/spl deg/ 3-dB beam width, 25 dB cross-polarization levels and an isolation better than 28 dB between the two ports. With an external quadrature hybrid coupler connected to the two orthogonal feedlines, the antenna yields 3-dB axial ratio bandwidth of more than 30% at 5.8 GHz.     

Miniaturized wideband dual linearly and circularly polarized printed square slot antenna for multiradio wireless systems

A dual symmetrical coplanar waveguide (CPW)-fed small size wideband printed square slot antenna (SSA) with dual linearly and circularly polarized radiation capability is presented. The antenna is composed using a square slot, two symmetrical orthogonal CPW feed lines connected to horizontal and vertical arm of L-shaped radiator, an embedded parasitic inverted-L strip at the lower left corner of the square ground slot and engraving slots in the ground plane. Circular polarization (CP) is achieved due to two orthogonal CPW feed lines and a common L-shaped radiator. Isolation between ports is improved by engraving slots at the lower left corner of ground plane and embedded parasitic inverted-L strip. The sense of dual-polarization can be changed in pass-band by changing the port excitation. Measured antenna reveals that an 84.4% (4.6 GHz, 3.15–7.75 GHz) −10 dB impedance bandwidth (IBW) and about 33% (2.03 GHz, 5.12–7.15 GHz) 3-dB axial ratio bandwidth (ARBW). Isolation between ports <−16 dB is achieved over usable CP band.     

毫米波圆极化单脉冲阵列天线的研究

在腔模理论基础上分析了单阵元圆极化微带贴片天线,研究了圆极化微带阵列天线的设计方法,采用相位旋转法设计了中心频率为35.75GHz的64元圆极化微带阵列天线与平面和差结构,使天线和和差馈电处于一个平面.利用Ansoft公司的HFSS软件进行了仿真优化.经过对天线实物的测试,此天线提供了21dB的增益,具有良好的轴比和驻波比,差波束零值深度大于20dB.     

一种新颖的宽带圆极化单极天线

该文设计了一种新颖的宽带圆极化单极子天线,该天线采用微带馈电模式。天线由C型贴片和改进的地板组成,整个天线尺寸仅为25×25×1 mm3。通过在C型贴片上切角和在地板上增加三角形微扰结构,可以有效增加天线的阻抗带宽和轴比带宽。该文给出了天线的设计流程,从表面电流分布分析了圆极化天线的工作机理。加工了天线实物,并对其进行了测量。仿真和实测结果表明天线具有超宽的阻抗带宽和轴比带宽。天线的工作频带为4.35～12 GHz(相对带宽为93.6%),3 dB轴比带宽为4.15～11.8 GHz(相对带宽为95.9%)。测量了天线的辐射性能和增益特性,实测结果与仿真结果吻合较好,证明了该天线的有效性。该天线可以应用于超宽带无线通信系统和卫星通信系统中。     

基于北斗卫星导航系统的一种圆极化微带天线

介绍一种用于北斗卫星导航系统的圆极化微带天线。该天线的主辐射器由开槽的圆形贴片构成,采用单点的同轴馈电,设计的中心工作频率为2．492GHz。仿真结果显示,调节圆形贴片中开槽的长度,可以分离出简并模,激励两个正交的模式,当两个分量相位为90deg,可以实现圆极化。实际测试中,｜S11｜于-10dB的阻抗带宽为0．09GHz,3dB轴比带宽为0．033GHz,与仿真结果基本吻合。     

一种基于5G应用的圆极化微带相控阵天线

本文提出一款应用于5G频段,可实现方位面±40°波束扫描的圆极化微带相控阵天线。该相控阵天线单元是由矩形贴片、上下介质板、缝隙耦合馈电结构、金属反射板构成。利用切比雪夫综合法的一分八不等分功分器实现相控阵天线的馈电形式。测试结果表明,阵列天线的驻波比带宽为3.25 GHz～3.69 GHz,端口隔离度大于25 dB,扫描过程中增益最大为21 dB,增益衰落小于3 dB,最大扫描角处轴比为2.89 dB。该天线具有低剖面、高隔离度、高增益以及良好的波束扫描性能等优点。     

Analysis of a dual circularly polarized microstrip antenna fed bycrossed slots

A dual circularly polarized, wideband microstrip antenna fed by two perpendicular crossed slots is analyzed in this work. The cross shaped aperture in the ground plane provides coupling between the microstrip patch and a single microstrip line underneath the ground plane, traversing the four arms of the cross in a serial manner, thereby generating four coupling points in phase quadratures for both senses of circular polarization. The analysis of this antenna incorporates two stages: In the first one, the individual load impedances are computed via an integral equation based on reciprocity, assuming no interactions between the ports. The second stage employs a transmission line model where the four coupling points are considered as lumped loads along the feed line. An iterative scheme employs the transmission line model for the determination of the actual impedances of each coupling point, including the mutual interactions with the other coupling points. This procedure provides control over the overall level of radiated energy; hence it can be used in the design procedure of this antenna as a serial or parallel fed array element. The computed results agree very well with measurements. The antenna attains a -3 dB gain bandwidth of 13% to 15%, a 3-dB axial ratio bandwidth of 48%, and -15 dB return loss bandwidth of 60%     

一种面向无线通信应用的宽频带圆极化天线阵

提出了一种新型宽频带2×2方形缝隙槽圆极化天线阵.天线阵包含一个连续旋转馈电结构、4个非对称U型馈电枝节和一个方形槽接地板.与传统圆极化天线阵所采用的L型馈电枝节不同,首次提出了一种新型非对称U形馈电枝节来改善天线的圆极化性能.利用这些枝节和缝隙槽作为微扰元素,缝隙槽天线阵可以激发多重圆极化谐振模式,进而产生宽频带的圆...     

用于整流天线的口径耦合圆极化微带天线的设计与实验

提出了一种用于整流天线的新型圆极化微带天线形式，此天线采用单端口径耦合馈电，易与整流电路集成和匹配。利用电磁场仿真软件分析了天线参数对天线性能的影响，设计并加工了一个圆极化天线单元。设计值和实验值较吻合，实验结果表明该天线在10．25GHz具有良好的圆极化特性：在最大方向上圆极化轴比为0．3dB，3dB圆极化带宽达到160MHz，驻波比小于2的带宽达到800MHz。     

低剖面宽带圆极化天线阵列

基于双馈双线极化微带天线,结合威尔金森功分器、T形结功分器及顺序旋转馈电的优点,设计了一种新型低剖面宽带圆极化2×2天线阵列。把辐射贴片和馈电网络集成在同一介质层,有效地利用了介质空间,降低了天线的剖面,增加了天线的带宽。4个天线单元顺序旋转90°,利用一分四T形结功分器给4个单元等幅、相位依次相差90°馈电。根据Ansoft''s HFSS仿真结果,制作了样机。样机实测结果和仿真结果吻合。实测结果表明,该天线阵驻波带宽可以达到27.78%,3-dB轴比带宽可以达到52%,最大增益为14.19 dB。     

一种寄生阵列宽带圆极化天线的设计

该文设计了一款C波段单馈寄生阵列的宽带圆极化天线。此天线采用紧邻的双层F4B介质基板,通过在方形驱动贴片上开槽及采用寄生阵列的设计实现了圆极化。对天线结构的设计步骤进行说明,研究了各结构对天线阻抗带宽和轴比带宽的影响,并研究了寄生贴片切角长度和驱动贴片上的缝隙宽度对天线轴比和带宽的影响。对天线的圆极化方向图进行了仿真。仿真结果表明,在5.5 GHz时实现了右旋圆极化,最大增益为8.1 dBi。加工并测试了宽带圆极化天线,测试结果与仿真结果基本相符,天线实测的阻抗带宽为1.3 GHz,轴比带宽为1.26 GHz。设计的叠层天线具有结构紧凑,装配简单和轴比带宽大的优点。     

64 单元X 波段高增益圆极化微带阵列天线设计

采用双层矩形贴片加切角的结构设计圆极化单元,并将其组成应用于X 波段64 单元高增益圆极化微带阵列天线。天线基板采用Taconic-TRF,介电常数4. 5,厚度0. 81mm,损耗角正切0. 0035。利用Ansoft HF-SS 软件对单元及阵列模型进行仿真优化。通过实际测试,64 单元阵列天线轴比AR<6dB 的带宽500MHz,增益达到21. 2dB,S11 <-10dB 的相对阻抗带宽达到6. 9%,天线具有良好的圆极化和阻抗匹配特性。圆极化天线具有较强的抗干扰能力,可很好地应用于电子侦察、电子对抗等领域。设计的圆极化微带阵列天线为组成更大阵列的天线以及构建相控阵天线提供了单元基础。     

一种新型宽带圆极化介质谐振器天线设计与实现*

设计了一种宽带圆极化介质谐振器天线,为一种鼠笼形的宽带一分四90毅相移功分微带馈电网络,采用缝隙耦合对介质谐振器顺序旋转耦合馈电。天线结构紧凑、加工简单,仿真和实测结果吻合良好,其阻抗带宽和低于3dB的轴比带宽重叠部分在1.09 GHz-1.83GHz、为50.7%。增益大于3dB 及轴比小于3dB 的波束宽度均达到90°。天线工作频率覆盖四大导航系统,包括中国的北斗系统、美国的GPS 系统、欧洲的伽利略(GALTLEO)系统和俄罗斯的格洛纳斯(GLONASS )系统的频段,天线可应用于全球卫星导航定位系统和无线宽带通信系统中。     

具有二次Koch分形边界的圆极化微带天线

设计了一种单馈点圆极化微带天线。微带贴片采用二次Koch分形边界的贴片结构,通过底馈方法激励起两个相互正交的简并模实现圆极化;采用CSTMicrowaveStudio@软件进行了仿真,其结果表明,在微带贴片的对角线上适当位置用探针馈电,可以实现圆极化辐射。对具有介质损耗的天线进行了仿真,结果与理想介质的差异较大。设计了一个右旋圆极化微带天线,并进行了测试。该天线工作于1．575GHz;VSWR小于2的阻抗带宽为51MHz;轴比为4dB;增益为3．8dB;贴片尺寸为42．4mm×42．4mm,可以用作GPS天线。     

一种新型UHF RFID阅读器圆极化天线

传统的圆极化阅读器天线采用单馈电微带天线方式设计,频带窄、极化特性较差。在单馈电微带天线的基础上,采用探针馈电曲线贴片的方式,在圆形铁片上开了4个对称的方形缝隙,最终设计出一种新型的UHF RFID圆极化阅读器天线。天线的结构尺寸为167.5 mm×167.5 mm×3 mm,阻抗带宽为870~936 MHz,3 dB轴比带宽为900~918 MHz,最大增益为3.5 dB。与传统的圆极化阅读器天线相比,设计的天线频带宽,且极化特性得到良好改善,能够满足工程上的应用需求。     

基于H形缝隙耦合的宽带圆极化微带天线

制作并测量了一种基于H形缝隙耦合的宽带圆极化微带天线,并讨论了天线的各结构参数对天线性能的影响。测量结果表明:通过Wilkinson功分器馈电,可使天线驻波带宽达47.5％,轴比带宽达50％,方向图前后比达－21dB,实现了低后瓣宽带圆极化微带天线的设计。