Low temperature UV/ozone oxidation formation of HfSiON gate dielectric

Physical and electrical properties of hafnium silicon oxynitride (HfSi_xO_yN_z) dielectric films prepared by UV ozone oxidation of hafnium silicon nitride (HfSiN) followed by annealing to 450 °C are reported. Interfacial layer growth was minimized through room temperature deposition and subsequent ultraviolet/ozone oxidation. The capacitance–voltage (C–V) and current–voltage (I–V) characteristics of the as-deposited and annealed HfSi_xO_yN_z are presented. These 4 nm thick films have a dielectric constant of 8–9 with 12 at.% Hf composition, with a leakage current density of 3×10⁻⁵ A/cm² at V_fb+1 V. The films have a breakdown field strength >10 MV/cm.     

The optical and electrical properties of copper indium di-selenide thin films

Thin films of copper indium di-selenide (CIS) with a wide range of compositions near stoichiometry have been formed on glass substrates in vacuum by the stacked elemental layer (SEL) deposition technique. The compositional and optical properties of the films have been measured by proton-induced X-ray emission (PIXE) and spectrophotometry (photon wavelength range of 300–2500 nm), respectively. Electrical conductivity (σ), charge-carrier concentration (n), and Hall mobility (μ_H) were measured at temperatures ranging from 143 to 400 K. It was found that more indium-rich films have higher energy gaps than less indium-rich ones while more Cu-rich films have lower energy gaps than less Cu-rich films. The sub-bandgap absorption of photons is minimum in the samples having Cu/In ≈ 1 and it again decreases, as Cu/In ratio becomes less than 0.60. Indium-rich films show n-type conductivities while near-stoichiometric and copper-rich films have p-type conductivities. At 300 K σ, n and μ_H of the films vary from 2.15 × 10⁻³ to 1.60 × 10⁻¹ (Ω cm)⁻¹, 2.28 × 10¹⁵ to 5.74 × 10¹⁷ cm⁻³ and 1.74 to 5.88 cm² (V s)⁻¹, respectively, and are dependent on the composition of the films. All the films were found to be non-degenerate. The ionization energies for acceptors and donors vary between 12 and 24, and 3 and 8 meV, respectively, and they are correlated well with the Cu/In ratios. The crystallites of the films were found to be partially depleted in charge carriers.     

Highly conducting indium tin oxide (ITO) thin films deposited by pulsed laser ablation

Highly conducting and transparent indium tin oxide (ITO) thin films were prepared on SiO₂ glass and silicon substrates by pulsed laser ablation (PLA) from a 90 wt.% In₂O₃-10 wt.% SnO₂ sintered ceramic target. The growths of ITO films under different oxygen pressures (P_O2) ranging from 1×10⁻⁴–5×10⁻² Torr at low substrate temperatures (T_s) between room temperature (RT) and 200°C were investigated. The opto-electrical properties of the films were found to be strongly dependent on the P_O2 during the film deposition. Under a P_O2 of 1×10⁻² Torr, ITO films with low resistivity of 5.35×10⁻⁴ and 1.75×10⁻⁴ Ω cm were obtained at RT (25°C) and 200°C, respectively. The films exhibited high carrier density and reasonably high Hall mobility at the optimal P_O2 region of 1×10⁻² to 1.5×10⁻² Torr. Optical transmittance in excess of 87% in the visible region of the solar spectrum was displayed by the films deposited at Po₂≥1×10⁻² Torr and it was significantly reduced as the P_O2 decreases.     

Dielectric properties of AlN films prepared by laser-induced chemical vapour deposition

The dielectric properties and electrical conductivity of AlN films deposited by laser-induced chemical vapour deposition (LCVD) are studied for a range of growth conditions. The static dielectric constant is 8.0 ± 0.2 over the frequency range 10²−10⁷ Hz and breakdown electric fields better than 10⁶ V cm⁻¹ are found for all films grown at temperatures above 130°C. The resistivity of the films grown under optimum conditions (substrate temperature above 170°C, NH₃/TMA flow rate ratio greater than 300 and a deposition pressure of 1–2 Torr) is about 10¹⁴ Ω cm and two conduction mechanisms can be identified. At low fields, F < 5 × 10⁵ V cm⁻¹ and conductivity is ohmic with a temperature dependence showing a thermal activation energy of 50–100 meV, compatible with the presumed shallow donor-like states. At high fields, F > 1 × 10⁶ V cm⁻¹, a Poole-Frenkel (field-induced emission) process dominates, with electrons activated from traps at about 0.7–1.2 eV below the conduction band edge. A trap in this depth region is well-known in AlN. At fields between 4 and 7 × 10⁵ V cm⁻¹ both conduction paths contribute significantly. The degradation of properties under non-ideal growth conditions of low temperature or low precursor V/III ratio is described.     

Destruction of carbon disulfide in aqueous solutions by sonochemical oxidation

Carbon disulfide (CS₂) is toxic to animals and aquatic organisms, and can also decompose to carbonyl sulfide (OCS) and hydrogen sulfide (H₂S) in aqueous environment. The kinetics of the sonochemical degradation of aqueous CS₂ was studied in a batch reactor at 20 kHz and 20 °C, and the effects of process parameters (e.g. concentration, ultrasonic intensity, irradiating gas) investigated. The concentrations of unbuffered CS₂ solutions used were (6.4–7.0)×10⁻⁴, 10.5×10⁻⁴ and (13.2–13.6)×10⁻⁴ M and the intensities were varied from 14 to 50 W. The reaction rate was found to be zero-order and the rate constant for the degradation at 20 °C and 14W in air was 21.1 μM/min using the largest initial concentration range studied. At the same initial concentration range but at 50 W (39.47 W/m²) the degradation rate of CS₂ was 46.7 μM/min, more than two times that at 14 W (11.04 W/m²). The rate of CS₂ sonochemical degradation in the presence of the different gases was in the order of He>air≥N₂O>Ar; the rate with helium was found to be about three times that of argon. The formation of sulfate (SO₄²⁻) as reaction product with air as the irradiating gas was enhanced in the presence of hydrogen peroxide (H₂O₂) and inhibited in the presence of 1-butanol. The sonochemical oxidation of CS₂ may prove to be an efficient and environmentally benign way for the removal of this hazardous pollutant from natural water and wastewater.     

Highly conducting doped poly-Si deposited by hot wire CVD and its applicability as gate material for CMOS devices

Highly conducting p- and n-type poly-Si:H films were deposited by hot wire chemical vapor deposition (HWCVD) using SiH₄+H₂+B₂H₆ and SiH₄+H₂+PH₃ gas mixtures, respectively. Conductivity of 1.2×10² (Ω cm)⁻¹ for the p-type films and 2.25×10² (Ω cm)⁻¹ for the n-type films was obtained. These are the highest values obtained so far by this technique. The increase in conductivity with substrate temperature (T_s) is attributed to the increase in grain size as reflected in the atomic force microscopy results. Interestingly conductivity of n-type films is higher than the p-type films deposited at the same T_s. To test the applicability of these films as gate contact Al/poly-Si/SiO₂/Si capacitor structures with oxide thickness of 4 nm were fabricated on n-type c-Si wafers. Sputter etching of the poly-Si was optimized in order to fabricate the devices. The performance of the HWCVD poly-Si as gate material was monitored using C–V measurements on a MOS test device at different frequencies. The results reveal that as deposited poly-Si without annealing shows low series resistance.     

Anomalous elastic response of amorphous alloys suggesting collective motions of many atoms

The dynamic Young’s modulus, E, of amorphous (a-) Zr₆₀Cu₃₀Al₁₀ (numbers indicate at.%) alloy was measured as a function of frequency, f, with a strain amplitude, _t, of 10⁻⁶, E(10⁻⁶,f), and also as a function of _t for f near 10² Hz, E(_t,10² Hz), by means of the vibrating reed methods. The elasticity study under the passing of electric current (PEC) was carried out too. E(10⁻⁶,f) is lower than E₀ for f between 10 and 10⁴ Hz showing local minima near 5×10, 5×10² and 5×10³ Hz, which are indicative of the resonant collective motion of many atoms, where E₀ is the static Young’s modulus. E(_t,10² Hz) increases showing saturation with increasing _t. Qualitatively, the outlines of E(10⁻⁶,f) and E(_t,10² Hz) observed for a-Zr₆₀Cu₃₀Al₁₀ are similar to those reported for various a-alloys. Quantitatively, a change in E(_t,10² Hz) for a-Zr₆₀Cu₃₀Al₁₀ is smallest among that reported for various a-alloys, presumably reflecting that the crystallization volume, (ΔV/V)_x, is smallest for a-Zr₆₀Cu₃₀Al₁₀. The effective charge number, Z^*, estimated from the change in E(10⁻⁶,10² Hz) due to PEC is 3.0×10⁵, which is comparable with Z^* reported for various a-alloys. We surmise that the number of atoms in the collective motions excited near 10² Hz is similar among various a-alloys. The E(10⁻⁶,f) data suggest that the spatial sizes of the density fluctuations may show a distribution.     

Excited-state absorption at 1.57 μm in U:CaF2 and Co:ZnSe saturable absorbers

Appreciable excited-state absorption (ESA) in U²⁺:CaF₂ and Co²⁺:ZnSe saturable absorbers was measured at λ=1.573 μm by optical transmission versus light fluence curves of 30–40 ns long pulses. The ground- and excited-state absorption cross-sections obtained were (9.15±0.3)×10⁻²⁰ and (3.6±0.2)×10⁻²⁰ cm², respectively, for U²⁺:CaF₂, and (57±4)×10⁻²⁰ and (12.5±1)×10⁻²⁰ cm² for Co²⁺:ZnSe. Thus, ESA is not negligible in U²⁺:CaF₂ and Co²⁺:ZnSe, as previously estimated.     

Up-conversion dynamics in GdAlO3:Er single crystal fibre

Green fluorescence has been obtained under continuous laser excitation in the 780–860 nm range in GdAlO₃:Er³⁺. With the help of the Judd-Ofelt treatment we built a model based on population rate equations to describe its time evolution. We found the intensity parameters to be Ω₂ = 2.045 × 10⁻²⁰ cm², Ω₄ = 1.356 × 10⁻²⁰ cm² Ω₆ = 1. 125 × 10⁻²⁰ cm². Even if a two-photon absorption and a looping mechanism are necessary to well describe the dynamics, the main process responsible for up-conversion is energy transfer between erbium ions.     

Reactions in Au/Nb bilayer thin films

The interdiffusion and intermetallic compound formation of Au/Nb bilayer thin films annealed at 200–400 °C have been investigated. The bilayer thin films were prepared by electron beam deposition. The Nb film was 50 nm thick and the Au film was 50–200 nm thick. The interdiffusion of annealed specimens was examined by measuring the electrical resistance and depth-composition profile and by transmission electron microscopy. Interdiffusion between the thin films was detected at temperatures above 325 °C in a vacuum of 10^-4 Pa. The intermetallic compound Au₂Nb₃ and other unknown phases form during annealing at over 400 °C. The apparent diffusion constants, determined from the penetration depth for annealing at 350 °C, are 3.5 × 10⁻¹⁵ m² s⁻¹ for Nb in Au and 8.6 × 110^7minus;15 m² s⁻¹ for Au in Nb. The Au surface of the bilayer films becomes uneven after annealing at over 400 °C due to the reaction.     

Phase formation at rapid thermal annealing of Al/Ti/Ni ohmic contacts on 4H-SiC

Ohmic contacts to the top p-type layers of 4H-SiC p⁺–n–n⁺ epitaxial structures having an acceptor concentration lower than 1×10¹⁹ cm⁻³ were fabricated by the rapid thermal anneal of multilayer Al/Ti/Pt/Ni metal composition. The rapid thermal anneal of multilayer A1/Ti/Pt/Ni metal composition led to the formation of duplex cermet composition containing Ni₂Si and TiC phases. The decomposition of the SiC under the contact was found to be down to a depth of about 100 nm. The contacts exhibited a contact resistivity R_c of 9×10⁻⁵ Ω cm⁻² at 21°C, decreasing to 3.1×10⁻⁵ Ω cm⁻² at 186°C. It was found that thermionic emission through the barrier having a height of 0.097 eV is the predominant current transport mechanism in the fabricated contacts.     

Growth and spectroscopy of Dy doped in ZnWO4 crystal

Single-crystal ZnWO₄:Dy³⁺ was grown by Czochralski technique. The XRD, absorption spectra as well as fluorescence spectrum are investigated and the Judd–Ofelt intensity parameters Ω₂, Ω₄, Ω₆ are obtained to be 7.76 × 10⁻²⁰ cm², 0.57 × 10⁻²⁰ cm², 0.31 × 10⁻²⁰ cm², respectively. Calculated radiative transition rate, branching ratios and radiative lifetime for different transition levels of ZnWO₄:Dy³⁺ crystals are presented. Fluorescence lifetime of ⁴F_9/2 level is 158 μs and quantum efficiency is 66%.The most intense fluorescence line at 575 nm correlative with transition ⁴F_9/2 → ⁶H_13/2 is potentially for application of yellow lasers.     

New transparent conducting MgIn2O4---Zn2In2O5 thin films prepared by magnetron sputtering

New materials for a transparent conducting oxide film are demonstrated. Highly transparent Zn₂In₂O₅ films with a resistivity of 3.9 × 10⁻⁴ Ω cm were prepared on substrates at room temperature using a pseudobinary compound powder target composed of ZnO (50 mol.%) and In₂O₃ (50 mol.%) by r.f. magnetron sputtering. MgIn₂O₄---Zn₂In₂O₅ films were prepared using MgIn₂O₄ targets with a ZnO content of 0–100 wt.%. The resistivity of the deposited films gradually decreased from 2 × 10⁻³ to 3.9 × 10⁻⁴ Ω cm as the Zn/(Mg + Zn) atomic ratio introduced into the films was increased. The greatest transparency was obtained in a MgIn₂O₄ film. The optical absorption edge of the films decreased as the Zn/(Mg + Zn) atomic ratio was increased, corresponding to the bandgap energy of their materials. It was found that the resistance of the undoped Zn₂In₂O₅ films was more stable than either the undoped MgIn₂O₄, ZnO or In₂O₃ films in oxidizing environments at high temperatures.     

Magnetic and electrical characterization of heavily boron-doped diamond

For a heavily boron-doped diamond (BDD) film, temperature variations of the electrical conductivity σ and magnetic susceptibility χ are reported. The room temperature σ 143 (Ω-cm)⁻¹ corresponds to a carrier concentration 10³ ppm, and its temperature variation yields an activation energy E_a 28 meV from 140 to 300 K and E_a0.88 meV from 40 to 80 K. It is argued that larger boron doping leads to lower magnitudes of E_a. The χ vs. T data (1.8–350 K) fits the Curie–Weiss law, with the concentration of paramagnetic species 120 ppm and a diamagnetic susceptibility −0.4×10⁻⁶ emu/g Oe. The results obtained from the measurements of σ and χ are discussed and compared.     

Semiconducting and structural properties of CrSi2 A-type epitaxial films on Si(111)

Chromium disilicide (CrSi₂) films 1 000 Å thick have been prepared by molecular beam epitaxy on CrSi₂ templates grown on Si(111) substrate. The effect of the substrate temperature on the structural, electrical and optical properties of CrSi₂ films has been studied by transmission and scanning electron microscopies, optical microscopy, electrical resistivity and Hall effect measurements and infrared optical spectrometry. The optimal temperature for the formation of the epitaxial A-type CrSi₂ film have been found to be about 750°C. The electrical measurement have shown that the epitaxial A-type CrSi₂ film is p-type semiconductor having a hole concentration of 1 × 10¹⁷cm⁻³ and Hall mobility of 2 980 cm² V⁻¹ s⁻¹ at room temperature. Optical absorption coefficient data have indicated a minimum, direct energy gap of 0.34 eV. The temperature dependence of the Hall mobility (μ) in the temperature range of T = 180–500 K can be expressed as μ = 7.8 × 10¹⁰T⁻³cm²V⁻¹s⁻¹.     

Al2O3 formation on Si by catalytic chemical vapor deposition

Catalytic chemical vapor deposition (Cat-CVD) has been developed to deposit alumina (Al₂O₃) thin films on silicon (Si) crystals using N₂ bubbled tri-methyl aluminum [Al(CH₃)₃, TMA] and molecular oxygen (O₂) as source species and tungsten wires as a catalyzer. The catalyzer dissociated TMA at approximately 600 °C. The maximum deposition rate was 18 nm min⁻¹ at a catalyzer temperature of 1000 °C and substrate temperature of 800 °C. Metal oxide semiconductor (MOS) diodes were fabricated using gates composed of 32.5-nm-thick alumina film deposited at a substrate temperature of 400 °C. The capacitance measurements resulted in a relative dielectric constant of 7.4, fixed charge density of 1.74×10¹² cm⁻², small hysteresis voltage of 0.12 V, and very few interface trapping charges. The leakage current was 5.01×10⁻⁷ A cm⁻² at a gate bias of 1 V.     

Crystallinity properties of parylene-n affecting its use as an ILD in submicron integrated circuit technology

Parylene-n (Poly-p-xylylene) (PA-n) [1–3] has a long history of use as a moisture barrier for printed circuit boards and hybrids. This paper evaluates this compound as a candidate vapor-depositable polymer interlayer dielectric for submicron integrated circuit technology due to its low dielectric constant, good step coverage, and high etch selectivity. To apply PA-n on high-density very large scale integrated circuits, its properties, such as deposition rate, deposition yield, and Crystallinity, are investigated as a function of deposition pressure and annealing temperature. The deposition rate was found in the range of 2.66 Pa to 13.3 Pa to be a linearly increasing function of pressure. Good-quality films were obtained when pressure was controlled below 10.64 Pa. Cloudy films, however, were found at 13.3 Pa. The deposition rate could be as high as 3.33 × 10⁻¹⁰ m s⁻¹ when deposited at 10.64 Pa. The plot of PA-n yield vs. pressure showed a constant plateau of 1 × 10⁻⁴ m kg⁻¹ from 2.66 Pa to 10.64 Pa. The optimum deposition rate was hence obtained at 10.64 Pa without compromising the deposition yield. The crystallinity-associated properties examined were hardness, dielectric constant, and water permeability. A lower deposition pressure was observed to produce higher Crystallinity that could be further enhanced by thermal annealing. A 5 × 10⁻⁸ m hard surface layer was detected with hardness 3.5 GPa, that was 3˜7 times larger than that of bulk hardness which was 0.4˜0.7 GPa. The bulk hardness was found to increase as Crystallinity increased. The dielectric constant tended to increase when the deposition pressure decreased. Furthermore, the dielectric constant was nearly constant when the polymer was heated up to temperatures as high as 698 K. This behavior, together with the formation of the hard layer and a higher Crystallinity, was believed to result from the improved film organization of the deposited films. The competition between the film build-up in the surface region and the monomer diffusion into the bulk region (penetration) was theorized to be responsible for the film organization. The water permeability, which was measured to be as low as 1.2 × 10⁻¹⁵ kg m⁻¹ s⁻¹ Pa⁻¹ and was found to increase as the deposition pressure was increased, further strengthened the film organization claim.     

Structure-composition-property dependence in reactive magnetron sputtered ZnO thin films

Thin films of zinc oxide (ZnO) were prepared by dc reactive magnetron sputtering on glass substrates at various oxygen partial pressures in the range 1×10⁻⁴–6×10⁻³ mbar and substrate temperatures in the range 548–723 K. The variation of cathode potential of zinc target on the oxygen partial pressure was explained in terms of target poisoning effects. The stoichiometry of the films has improved with the increase in the oxygen partial pressure. The films were polycrystalline with wurtzite structure. The films formed at higher substrate temperatures were (0 0 2) oriented. The temperature dependence of Hall mobility of the films formed at various substrate temperatures indicated that the grain boundary scattering of charge carriers was predominant electrical conduction mechanism in these films. The optical band gap of the films increased with the increase of substrate temperature. The ZnO films formed under optimized oxygen partial pressure of 1×10⁻³ mbar and substrate temperature of 663 K exhibited low electrical resistivity of 6.9×10⁻² Ω cm, high visible optical transmittance of 83%, optical band gap of 3.28 eV and a figure of merit of 78 Ω⁻¹ cm⁻¹.     

Underlying mechanisms for unique elastic properties of nanocrystalline Au

In order to get an insight into the grain boundaries (GBs) in nanocrystalline (n-) metal, we prepared the high-density n-Au with ρ/ρ₀>99% by the gas-deposition method and carried out the vibrating reed measurements, where ρ/ρ₀ is the relative density referring to the bulk density. The strain amplitude dependence (SAMD) of the resonant frequency (f) and the internal friction (Q⁻¹) was measured for the strain () amplitude between 10⁻⁶ and 2×10⁻³ and for temperature between 5 and 300 K. No plastic deformations are detected for the present strain range, where f decreases for up to 10⁻⁴ and then turns to increase, showing saturation for between 10⁻⁴ and 2×10⁻³. The low temperature irradiation by 2 MeV electrons or 20 MeV protons causes an increase in the Young’s modulus at 6 K, which is surmised to reflect a modification of the anelastic process in the GB regions. In contrast, the SAMD of f is hardly modified by irradiation, suggesting that it is indicative of a collective motion of atoms in n-Au.     

A kinetic model for the degradation of benzothiazole by Fe3+-photo-assisted Fenton process in a completely mixed batch reactor

The degradation of benzothiazole in aqueous solution by a photo-assisted Fenton reaction has been studied in a batch reactor in the pH range 2.0–3.2 and for H₂O₂ and Fe(III) concentrations respectively between 1.0×10⁻³–1.5×10⁻¹ and 1.0×10⁻⁶–4.0×10⁻⁶ M.

A kinetic model has been developed to predict the decay of benzothiazole at varying reaction conditions. The use of kinetic constants from the literature in the model allows to simulate the system behavior by taking into account the influence of pH, hydrogen peroxide, Fe(III) and sulfate concentrations and the ionic strength.