Evaluating the ability of separation and adsorption of SO<Subscript>2</Subscript> by nano-CuO-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> in high concentrations and moderate temperatures

Nano CuO-Fe₂O₃/TiO₂ adsorbents were made with different compositions of metal oxides using precipitation- desorption method. The adsorbents were applied for adsorption of SO₂ at high concentrations ranging from 10,000 to 30,000 ppm and temperatures between 523 and 627 K. Adsorption experiments were applied for adsorbents in a laboratory fixed bed adsorption column. The adsorption capacity was measured by calculating the area under the adsorption curve using the integral method. The results showed that temperature is the most affecting factor on the adsorption capacity. The highest adsorption capacity was obtained by using 17, 8 and 75 wt% of CuO, Fe₂O₃ and nano TiO₂, respectively. Characteristics of the best sorbent were determined by using Fe-SEM, XRD and nitrogen adsorption-desorption analyses.     

Performance Comparison of Different Separation Systems for H2 Recovery from Catalytic Reforming Unit Off‐Gas Streams

The performance of pressure swing adsorption (PSA), membrane separation, and gas absorption systems for H₂ recovery from refinery off‐gas stream was studied by simulation‐based data. The PSA process was simulated using adsorbents of silica gel and activated carbon for removing heavy and light hydrocarbons. The mole fraction profiles of all components and the relationship between hydrogen purity and recovery as a function of feed pressure were examined. The solution‐diffusion model was applied for modeling and simulation of a one‐stage membrane process. The gas absorption process with a tower tray was simulated at sub‐zero temperature and the correlation between hydrogen purity and recovery as a function of tower pressure and temperature was evaluated at different solvent flow rates.     

Adsorptive separation of CO<Subscript>2</Subscript> and CH<Subscript>4</Subscript> by the broom sorghum based activated carbon functionalized by diethanolamine

A low-cost activated carbon (AC) was produced from the broom sorghum stalk using KOH as the chemical activating agent, and then the surface of AC was functionalized with diethanolamine to enhance CO₂/CH4 selectivity. Characteristics of pristine and DEA-functionalized ACs were determined through different analyses such as Boehm’s method, BET, FT-IR, SEM, and TGA. The adsorption behavior of pure carbon dioxide and pure methane on these adsorbents was investigated in a temperature range of 288-308 K and pressure range of 0-25 bar using an apparatus based on a volumetric method. Results indicated that amine functionalization significantly improved the selectivity of CO₂/CH₄. The enhancement of CO₂ ideal adsorption selectivity over CH₄ from 1.51 for the pristine AC to 5.75 for the AC-DEA was attributed to adsorbate-adsorbent chemical interaction. The present DEA-functionalized AC adsorbent can be a good candidate for applications in natural gas and landfill gas purifications.     

Efficient pressure swing adsorption for improving H<Subscript>2</Subscript> recovery in precombustion CO<Subscript>2</Subscript> capture

An efficient design for pressure swing adsorption (PSA) operations is introduced for CO₂ capture in the pre-combustion process to improve H₂ recovery and CO₂ purity at a low energy consumption. The proposed PSA sequence increases the H₂ recovery by introducing a purge step which uses a recycle of CO₂-rich stream and a pressure equalizing step. The H₂ recovery from the syngas can be increased over 98% by providing a sufficient purge flow of 48.8% of the initial syngas feeding rate. The bed size (375m³/(kmol CO₂/s)) and the energy consumption for the compression of recycled CO₂-rich gas (6 kW/(mol CO₂/s)) are much smaller than those of other PSA processes that have a CO₂ compression system to increase the product purity and recovery.     

Adsorption of CO<Subscript>2</Subscript> by iron-exchanged heteropolyacid Fe<Subscript>1.5</Subscript>PMo<Subscript>12</Subscript>O<Subscript>40</Subscript> supported on mesoporous cellular foams

Novel low-temperature swing adsorbents that preferably adsorb CO₂ were synthesized by varying loading of heteropolyacid Fe_1.5PMo₁₂O₄₀ (Fe–PMA) supporting on mesoporous cellular foams (MCFs) by wetting impregnation. The synthesized materials were characterized by various physicochemical, thermal and spectral techniques and the CO₂ adsorption capacity of the materials were evaluated. Solid adsorbents showed a significantly high adsorption capacity toward CO₂ due to the chemisorptions of CO₂. The CO₂ adsorption capacities of the materials decreased as the temperature increased. The results showed that the adsorption capacity reached a level of 81.8 mg CO₂/g-adsorbent at 25 °C for the 20 wt% Fe–PMA–MCFs. These results indicated that the iron (Fe²⁺) complexes acted as efficient catalysts for the separation of CO₂. The as-synthesized adsorbents were selective, thermally stable, long-lived, and could be recycled at a temperature of 110 °C.     

Adsorption characteristics analysis of CO<Subscript>2</Subscript> and N<Subscript>2</Subscript> in 13X zeolites by molecular simulation and N<Subscript>2</Subscript> adsorption experiment

The adsorption characteristics of CO₂ and N₂ in 13X zeolites have been studied by the molecular simulation and N₂ adsorption experiment. It is found that the simulation results by Dreiding force fields are in an agreement with the published data. The influence of the σ and ε parameters of O_Z and Na⁺ on the adsorption performance is discussed. Then the optimized force field parameters are obtained. Specific surface area (S _B ) is calculated by simulation and experiment. Its relative error is just only 4.3 %. Therefore, it is feasible that S _B of 13X zeolites is obtained by the simulation methods. Finally, the impacts of pressure and temperature on adsorption characteristics are investigated. At low pressure, CO₂ adsorption in 13X zeolites belongs to the surface adsorption. As the pressure increase, the partial multilayer adsorption appears along with the surface adsorption. N₂ adsorption in 13X zeolites is different from that of CO₂. At low temperature of 77 K, two primary peaks are caused by the surface adsorption and multilayer adsorption respectively regardless of pressure variation. When the temperature is 273 K, the energy distribution curve appears undulate at low pressures. Then it becomes stable with the pressure increase. The surface adsorption plays an important role at the relative high pressures. The results will help to provide the theory guide for the optimization of force field parameters of adsorbents, and it is very important significance to understand the adsorption performance of zeolites.     

Vacuum swing adsorption process for the separation of ethylene/ethane with AgNO<Subscript>3</Subscript>/clay adsorbent

The performance of the 4-bed and 3-bed VSA process using AgNO₃/clay adsorbent for the ethylene separation from C2 fractionator feed (83.56% C₂H₄, 16.44% C₂H₆) was investigated experimentally and theoretically. With the 4-bed VSA process, extremely high recovery of ethylene, over 99%, was obtained at ethylene purity of 99.8%. The recovery of the 3-bed process was lower about by 1% than that of the 4-bed VSA process. But, the productivity of the 3-bed VSA was higher about by 33% than that of the 4-bed VSA process. The productivity of the 3-bed VSA process was 3.7 mol/kg/hr at the ethylene purity of 99.8%. Effects of the rinse flow rate in the 3-bed VSA process were investigated by both experiment and simulation. The purity of ethylene was not significantly improved by the increase of the rinse flow rate after it reached 99.8%. At the rinse flow rate where the purity was 99.9%, the recovery became 70%. It might be attributed to the slow diffusion of ethane. According to the simulation, ethylene purity of over 99.9% could be obtained with recovery of over 90% only when the mass transfer rate of ethane is lower than 1.0×10^-4 s^-1 or higher than 0.2 s^-1. The productivity of the process could be improved by increasing the feed flow rate at the expense of the recovery. According to the simulation, at the feed flow rate of 5,000 ml/min, the productivity of 5.2 mol/kg/hr was obtained at the ethylene purity of 99.5%. This paper is dedicated to Professor Hyun-Ku Rhee on the occasion of his retirement from Seoul National University.     

快速变压吸附制氢工艺的模拟与分析

目前工业上主要通过变压吸附技术从蒸汽甲烷重整气中制取氢产品气。然而,能源需求量的快速增加使得传统变压吸附技术在产量方面的不足越发明显。为此,进行了快速变压吸附从蒸汽甲烷重整气中制取氢气的模拟研究。采用活性炭和5A分子筛作为吸附剂,并以测得的原料气中各组分在两种吸附剂上的吸附数据为基础,进行了六塔快速变压吸附工艺的数值模拟与分析。在分析了塔内温度、压力和固相的浓度分布后,探究了进料流量、双层吸附剂高度比以及冲洗进料比三个操作参数对于快速变压吸附工艺性能的影响,结果表明：原料气组成为H₂/CH₄/CO/CO₂=76%/3.5%/0.5%/20%,吸附压力为22 bar（1 bar=10⁵ Pa）,解吸吹扫压力为1.0 bar,处理量为0.8875 mol·s^-1,吸附剂床层高度比为0.5∶0.5,冲洗进料比为22.37%时,可获得H₂纯度99.90%,回收率69.88%,此时H₂产量为0.4713 mol·s^-1。相比之下,氢气纯度为99.90%时,尽管PSA工艺回收率为83.40%,但处理量只有0.39 mol·s^-1,因此H₂产量仅为0.2472 mol·s^-1。     

Characterization and fluorine-free microwave hydrothermal synthesis of AlPO<Subscript>4</Subscript>-5 molecular sieves as adsorbents

With a characteristic of S-shaped water sorption isotherms, AlPO₄-5 molecular sieves have been considered as up-and-coming adsorbents for the utilization in adsorptive cooling and heating systems. In order to avoid toxicity and corrosion of fluoride, this paper introduced a fluorine-free microwave hydrothermal synthesis strategy of pure AlPO₄-5 crystals. The effects of hydrothermal conditions including template agent, crystallization temperature and time on the performances of AlPO₄-5 adsorbents were systematically investigated. Fourier transform infrared spectroscopy, X-ray diffraction (XRD), ²⁷Al and ³¹P solid state magic angle spinning nuclear magnetic resonance (MAS NMR), pore size analyzer and Scanning electron microscopy (SEM) were used to determine the chemical structure, crystalloid phase, framework, pore structure and the morphology. Adsorption and desorption performances were measured by static adsorption, thermogravimetry and temperature programmed desorption. XRD results indicated that both triethylamine and tetraethylammonium hydroxide as templates, AlPO₄-5 crystals could quickly be synthesized within 30–45 min under fluorine-free microwave irradiation. By comparison, the adsorption and desorption performance of the former (recorded as AlPO₄-5A) was superior to that of the latter (recorded as AlPO₄-5H). FT-IR, MAS NMR and SEM results revealed that AlPO₄-5 crystals have the frameworks of alternating AlO₄ and PO₄ units and typical hexagonal rod-like morphologies.     

A Novel Process for Renewable Methane Production: Combining Direct Air Capture by K<Subscript>2</Subscript>CO<Subscript>3</Subscript>/Alumina Sorbent with CO<Subscript>2</Subscript> Methanation over Ru/Alumina Catalyst

CO₂ methanation over supported ruthenium catalysts is considered to be a promising process for carbon capture and utilization and power-to-gas technologies. In this work 4% Ru/Al₂O₃ catalyst was synthesized by impregnation of the support with an aqueous solution of Ru(OH)Cl₃, followed by liquid phase reduction using NaBH₄ and gas phase activation using the stoichiometric mixture of CO₂ and H₂ (1:4). Kinetics of CO₂ methanation reaction over the Ru/Al₂O₃ catalyst was studied in a perfectly mixed reactor at temperatures from 200 to 300 °C. The results showed that dependence of the specific activity of the catalyst on temperature followed the Arrhenius law. CO₂ conversion to methane was shown to depend on temperature, water vapor pressure and CO₂:H₂ ratio in the gas mixture. The Ru/Al₂O₃ catalyst was later tested together with the K₂CO₃/Al₂O₃ composite sorbent in the novel direct air capture/methanation process, which combined in one reactor consecutive steps of CO₂ adsorption from the air at room temperature and CO₂ desorption/methanation in H₂ flow at 300 or 350 °C. It was demonstrated that the amount of desorbed CO₂ was practically the same for both temperatures used, while the total conversion of carbon dioxide to methane was 94.2–94.6% at 300 °C and 96.1–96.5% at 350 °C.     

Synthesis of MIL-101@g-C<Subscript>3</Subscript>N<Subscript>4</Subscript> nanocomposite for enhanced adsorption capacity towards CO<Subscript>2</Subscript>

MIL-101@g-C₃N₄ nanocomposite was prepared by solvothermal synthesis and used for CO₂ adsorption. The parent materials (MIL-101 and g-C₃N₄) and the MIL-101@g-C₃N₄ were characterized by X-ray diffraction, argon adsorption/desorption, Fourier transform infrared spectroscopy, thermal analysis (TG/DTA), transmission electronic microscopy, and Energy-dispersive X-ray spectroscopy. The results confirmed the formation of well-defined MIL-101@g-C₃N₄ with interesting surface area and pore volume. Furthermore, both MIL-101 and MIL-101@g-C₃N₄ were accomplished in carbon dioxide capture at different temperatures (280, 288, 273 and 298 K) at lower pressure. The adsorption isotherms show that the nanocomposite has a good CO₂ adsorption affinity compared to MIL-101. The best adsorption capacity is about 1.6 mmol g^?1 obtained for the nanocomposite material which is two times higher than that of MIL-101, indicating strong interactions between CO₂ and MIL-101@g-C₃N₄. This difference in efficacy is mainly due to the presence of the amine groups dispersed in the nanocomposite. Finally, we have developed a simple route for the preparation of an effective and new adsorbent for the removal of CO₂, which can be used as an excellent candidate for gas storage, catalysis, and adsorption.     

Cu/ZnO/AlOOH catalyst for methanol synthesis through CO<Subscript>2</Subscript> hydrogenation

Catalytic conversion of CO₂ to methanol is gaining attention as a promising route to using carbon dioxide as a new carbon feedstock. AlOOH supported copper-based methanol synthesis catalyst was investigated for direct hydrogenation of CO₂ to methanol. The bare AlOOH catalyst support was found to have increased adsorption capacity of CO₂ compared to conventional Al₂O₃ support by CO₂ temperature-programmed desorption (TPD) and FT-IR analysis. The catalytic activity measurement was carried out in a fixed bed reactor at 523 K, 30 atm and GHSV 6,000 hr^?1 with the feed gas of CO₂/H₂ ratio of 1/3. The surface basicity of the AlOOH supported Cu-based catalysts increased linearly according to the amount of AlOOH. The optimum catalyst composition was found to be Cu : Zn : Al=40 : 30 : 30 at%. A decrease of methanol productivity was observed by further increasing the amount of AlOOH due to the limitation of hydrogenation rate on Cu sites. The AlOOH supported catalyst with optimum catalyst compositions was slightly more active than the conventional Al₂O₃ supported Cu-based catalyst.     

Application of ZnO and TiO<Subscript>2</Subscript> nanoparticles coated onto montmorillonite in the presence of H<Subscript>2</Subscript>O<Subscript>2</Subscript> for efficient removal of cephalexin from aqueous solutions

This study considers the feasibility of uptake of cephalexin, an emerging contaminant, from aqueous solutions by using green local montmorillonite (GLM), montmorillonite coated with ZnO (ZnO/GLM) and montmorillonite coated with TiO₂ (TiO₂/GLM) in the presence of H₂O₂. Batch adsorption experiments were carried out as a function of pH, initial concentration of the cephalexin, adsorbent dosage, contact time, and temperature. Finally, the adsorbents were characterized by XRD, SEM and FTIR analyses. XRD patterns showed dramatic changes in the adsorbents after loading with the nanoparticles, confirming successful placing of the nanoparticles onto GLM. The GLM mineral surface after nanoparticle loading appears to be fully exposed and more porous with irregular shapes in particles diameters of 1-50 microns. FTIR analyses also confirmed dramatic changes in surface functional groups after modification with these nanoparticles. The results showed that the removal efficiency of cephalexin was better at lower pH values. Totally, the removal efficiency increased with increase in adsorbent dosage and contact time and decreased with concentration and temperature increase. The thermodynamics values of ΔG ^o and ΔH ^o revealed that the adsorption process was spontaneous and exothermic. In isotherm study, the maximum adsorption capacities (qm) were obtained to be 7.82, 17.09 and 49.26 mg/g for GLM, ZnO/GLM and TiO₂/GLM, respectively. Temkin constant (B _T ) showed that adsorption of cephalexin from solution was exothermic for all three adsorbents.     

Preparation of amine-modified SiO<Subscript>2</Subscript> aerogel from rice husk ash for CO<Subscript>2</Subscript> adsorption

Amine-modified SiO₂ aerogel was prepared using 3-(aminopropyl)triethoxysilane (APTES) as the modification agent and rice husk ash as silicon source, its CO₂ adsorption performance was investigated. The amine-modified SiO₂ aerogel remains porous, the specific surface area is 654.24 m²/g, the pore volume is 2.72 cm³/g and the pore diameter is 12.38 nm. The amine-modified aerogel, whose N content is up to 3.02 mmol/g, can stay stable below the temperature of 300 °C. In the static adsorption experiment, amine-modified SiO₂ aerogel (AMSA) showed the highest CO₂ adsorption capacity of 52.40 cm³/g. A simulation was promoted to distinguish the adsorption between the physical process and chemical process. It is observed that the chemical adsorption mainly occurs at the beginning, while the physical adsorption affects the entire adsorption process. Meanwhile, AMSA also exhibits excellent CO₂ adsorption–desorption performance. The CO₂ adsorption capacity dropped less than 10 % after ten times of adsorption–desorption cycles. As a result, AMSA with rice husk ash as raw material is a promising CO₂ sorbent with high adsorption capacity and stable recycle performance and will have a broad application prospect for exhaust emission in higher temperature.     

Synthesis and catalytic properties of nanostructured Me/Mn<Subscript>0.5</Subscript>Ce<Subscript>0.5</Subscript>O<Subscript>2</Subscript> in the oxidation of carbon monoxide

The nanostructured solid solution Mn_0.5Ce_0.5O₂ is synthesized to develop effective noble metal free catalysts for the detoxification of technogenic contaminants. Its chemical and phase compositions and textural characteristics are studied by differential thermal analysis, X-ray diffraction analysis, laser mass spectrometry, and low-temperature nitrogen adsorption. The activity of the solid solution in the oxidation of carbon monoxide is determined by the flow method within a temperature range of 20–300°C at atmospheric pressure, a gas hourly space velocity of 1800 h⁻¹ for the following gas mixture composition, vol %: CO, 3.6; O₂, 8.0; N₂, balance. The activity of Mn_0.5Ce_0.5O₂ is shown to be appreciably higher than the activity of MnO_x and CeO₂, and the temperature of 100% conversion is 92, 120, and 210°C, respectively. Using the solid solution as a support and the technique of impregnation, we synthesize the nanostructured catalysts Cu/Mn_0.5Ce_0.5O₂ and Ag/Mn_0.5Ce_0.5O₂, which manifest high activity in the oxidation of carbon monoxide: the temperature of 100% conversion is 77 and 85°C, respectively. The new catalysts could be of interest for the purification of industrial and motor vehicle wastes.     

Carbonization and CO<Subscript>2</Subscript> activation of scrap tires: Optimization of specific surface area by the Taguchi method

This research demonstrates the production of activated carbon from scrap tires via physical activation with carbon dioxide. A newly constructed apparatus was utilized for uninterrupted carbonization and activation processes. Taguchi experimental design (L16) was applied to conduct the experiments at different levels by altering six operating parameters. Carbonization temperature (550–700 °C), activation temperature (800–950 °C), process duration (30–120 min), CO₂ flow rate (400 and 600 cc/min) and heating rate (5 and 10 °C/min) were the variables examined in this study. The effect of parameters on the specific surface area (SSA) of activated carbon was studied, and the influential parameters were identified employing analysis of variance (ANOVA). The optimum conditions for maximum SSA were: carbonization temperature=650 °C, carbonization time=60 min, heating rate=5 °C/min, activation temperature= 900 °C, activation time=60 min and CO₂ flow rate=400 cc/min. The most effective parameter was activation temperature with an estimated impact of 49%. The activated carbon produced under optimum conditions was characterized by pore and surface structure analysis, iodine adsorption test, ash content, scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR). The process yield for optimized activated carbon was 13.2% with the following properties: specific surface area=437 m²/g, total pore volume=0.353 cc/g, iodine number=404.7 mg/g and ash content=13.9% along with an amorphous structure and a lot of oxygen functional groups. These properties are comparable to those of commercial activated carbons.     

Separation characteristics of tetrapropylammoniumbromide templating silica/alumina composite membrane in CO<Subscript>2</Subscript>/N<Subscript>2</Subscript>, CO<Subscript>2</Subscript>/H<Subscript>2</Subscript> and CH<Subscript>4</Subscript>/H<Subscript>2</Subscript> systems

Nanoporous silica membrane without any pinholes and cracks was synthesized by organic templating method. The tetrapropylammoniumbromide (TPABr)-templating silica sols were coated on tubular alumina composite support ( γ-Al₂O₃/ α-Al₂O₃ composite) by dip coating and then heat-treated at 550 °C. By using the prepared TPABr templating silica/alumina composite membrane, adsorption and membrane transport experiments were performed on the CO₂/N₂, CO₂/H₂ and CH₄/H₂ systems. Adsorption and permeation by using single gas and binary mixtures were measured in order to examine the transport mechanism in the membrane. In the single gas systems, adsorption characteristics on the α-Al₂O₃ support and nanoporous unsupport (TPABr templating SiO₂/ γ-Al₂O₃ composite layer without α-Al₂O₃ support) were investigated at 20–40 °C conditions and 0.0–1.0 atm pressure range. The experimental adsorption equilibrium was well fitted with Langmuir or/and Langmuir-Freundlich isotherm models. The α-Al₂O₃ support had a little adsorption capacity compared to the unsupport which had relatively larger adsorption capacity for CO₂ and CH₄. While the adsorption rates in the unsupport showed in the order of H₂> CO₂> N₂> CH₄ at low pressure range, the permeate flux in the membrane was in the order of H₂≫N₂> CH₄> CO₂. Separation properties of the unsupport could be confirmed by the separation experiments of adsorbable/non-adsorbable mixed gases, such as CO₂/H₂ and CH₄/H₂ systems. Although light and non-adsorbable molecules, such as H₂, showed the highest permeation in the single gas permeate experiments, heavier and strongly adsorbable molecules, such as CO₂ and CH₄, showed a higher separation factor (CO₂/H₂=5-7, CH₄/H₂=4-9). These results might be caused by the surface diffusion or/and blocking effects of adsorbed molecules in the unsupport. And these results could be explained by surface diffusion. This paper is dedicated to Professor Hyun-Ku Rhee on the occasion of his retirement from Seoul National University.     

Adsorption of Tetracycline with Reduced Graphene Oxide Decorated with MnFe<Subscript>2</Subscript>O<Subscript>4</Subscript> Nanoparticles

Nanomaterials were widely used as efficient adsorbents for environmental remediation of tetracycline pollution. However, the separation of the adsorbents posed the challenge to their practical applications. In this study, we grew magnetic MnFe₂O₄ nanoparticles on the reduced graphene oxide (rGO) to form MnFe₂O₄/rGO nanocomposite with a one-step method. When used as the absorbent of Tetracycline, it exhibited an adsorption capacity of 41?mg/g. The adsorption kinetics and isotherm were fitted well with the pseudo-second order model and Freundlich model, respectively. The MnFe₂O₄/rGO nanocomposite could be easily extracted from the solution with the external magnetic field and regenerated with acid washing.     

CO<Subscript>2</Subscript> methanation and co-methanation of CO and CO<Subscript>2</Subscript> over Mn-promoted Ni/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

A series of Mn-promoted 15 wt-% Ni/Al₂O₃ catalysts were prepared by an incipient wetness impregnation method. The effect of the Mn content on the activity of the Ni/Al₂O₃ catalysts for CO₂ methanation and the comethanation of CO and CO₂ in a fixed-bed reactor was investigated. The catalysts were characterized by N2 physisorption, hydrogen temperature-programmed reduction and desorption, carbon dioxide temperature-programmed desorption, X-ray diffraction and highresolution transmission electron microscopy. The presence of Mn increased the number of CO₂ adsorption sites and inhibited Ni particle agglomeration due to improved Ni dispersion and weakened interactions between the nickel species and the support. The Mn-promoted 15 wt-% Ni/Al₂O₃ catalysts had improved CO₂ methanation activity especially at low temperatures (250 to 400 °C). The Mn content was varied from 0.86% to 2.54% and the best CO₂ conversion was achieved with the 1.71Mn-Ni/Al₂O₃ catalyst. The co-methanation tests on the 1.71Mn-Ni/Al₂O₃ catalyst indicated that adding Mn markedly enhanced the CO₂ methanation activity especially at low temperatures but it had little influence on the CO methanation performance. CO₂ methanation was more sensitive to the reaction temperature and the space velocity than the CO methanation in the co-methanation process.

Open image in new window

     

Sorption studies of CO<Subscript>2</Subscript>, CH<Subscript>4</Subscript>, N<Subscript>2</Subscript>, CO,O<Subscript>2</Subscript> and Ar on nanoporous aluminum terephthalate [MIL-53(Al)]

Aluminum terephthalate, MIL-53(Al), metal–organic framework synthesized hydrothermally and purified by solvent extraction method was used as an adsorbent for gas adsorption studies. The synthesized MIL-53(Al) was characterized by powder X-Ray diffraction analysis, surface area measurement using N₂ adsorption–desorption at 77 K, FTIR spectroscopy and thermo gravimetric analysis. Adsorption isotherms of CO₂, CH₄, CO, N₂, O₂ and Ar were measured at 288 and 303 K. The absolute adsorption capacity was found in the order CO₂>CH₄>CO>N₂>Ar>O₂. Henry’s constants, heat of adsorption in the low pressure region and adsorption selectivities for the adsorbate gases were calculated from their adsorption isotherms. The high selectivity and low heat of adsorption for CO₂ suggests that MIL-53(Al) is a potential adsorbent material for the separation of CO₂ from gas mixtures. The high selectivity for CH₄ over O₂ and its low heat of adsorption suggests that MIL-53(Al) could also be a compatible adsorbent for the separation of methane from methane–oxygen gas mixtures.