Performance studies of multilayer hard surface coatings (TiN/TiCN/Al2O3/TiN) of indexable carbide inserts in hard machining: Part-I (An experimental approach)

In recent years, hard machining using CBN and ceramic inserts became an emerging technology than traditional grinding and widely used manufacturing processes. However the relatively high cost factors associated with such tools has left a space to look for relatively low cost cutting tool materials to perform in an acceptable range. Multilayer coated carbide insert is the proposed alternative in the present study due to its low cost. Thus, an attempt has been made to have an extensive study on the machinability aspects such as flank wear, chip morphology, surface roughness in finish hard turning of AISI 4340 steel (HRC 47 ± 1) using multilayer coated carbide (TiN/TiCN/Al₂O₃/TiN) insert under dry environment. Parametric influences on turning forces are also analyzed. From the machinability study, abrasion and chipping are found to be the dominant wear mechanism in hard turning. Multilayer TiN coated carbide inserts produced better surface quality and within recommendable range of 1.6 μm i.e. comparable with cylindrical grinding. At extreme parametric conditions, the growth of tool wear was observed to be rapid thus surface quality affected adversely. The chip morphology study reveals a more favorable machining environment in dry machining using TiN coated carbide inserts. The cutting speed and feed are found to have the significant effect on the tool wear and surface roughness from ANOVA study. It is evident that, thrust force (Fy) is the largest component followed by tangential force (Fz) and the feed force (Fx) in finish hard turning. The observations yield the machining ability of multilayer TiN coated carbide inserts in hard turning of AISI 4340 steel even at higher cutting speeds.     

Experimental investigations on machinability aspects in finish hard turning of AISI 4340 steel using uncoated and multilayer coated carbide inserts

The present work deals with some machinability studies on flank wear, surface roughness, chip morphology and cutting forces in finish hard turning of AISI 4340 steel using uncoated and multilayer TiN and ZrCN coated carbide inserts at higher cutting speed range. The process has also been justified economically for its effective application in hard turning. Experimental results revealed that multilayer TiN/TiCN/Al₂O₃/TiN coated insert performed better than uncoated and TiN/TiCN/Al₂O₃/ZrCN coated carbide insert being steady growth of flank wear and surface roughness. The tool life for TiN and ZrCN coated carbide inserts was found to be approximately 19 min and 8 min at the extreme cutting conditions tested. Uncoated carbide insert used to cut hardened steel fractured prematurely. Abrasion, chipping and catastrophic failure are the principal wear mechanisms observed during machining. The turning forces (cutting force, thrust force and feed force) are observed to be lower using multilayer coated carbide insert in hard turning compared to uncoated carbide insert. From 1st and 2nd order regression model, 2nd order model explains about 98.3% and 86.3% of the variability of responses (flank wear and surface roughness) in predicting new observations compared to 1st order model and indicates the better fitting of the model with the data for multilayer TiN coated carbide insert. For ZrCN coated carbide insert, 2nd order flank wear model fits well compared to surface roughness model as observed from ANOVA study. The savings in machining costs using multilayer TiN coated insert is 93.4% compared to uncoated carbide and 40% to ZrCN coated carbide inserts respectively in hard machining taking flank wear criteria of 0.3 mm. This shows the economical feasibility of utilizing multilayer TiN coated carbide insert in finish hard turning.     

A comparative study on performance of multilayer coated and uncoated carbide inserts when turning AISI D2 steel under dry environment

The present work deals with a comparative study on flank wear, surface roughness, tool life, volume of chip removal and economical feasibility in turning high carbon high chromium AISI D2 steel with multilayer MTCVD coated [TiN/TiCN/Al₂O₃/TiN] and uncoated carbide inserts under dry cutting environment. Higher micro hardness of TiN coated carbide samples (1880 HV) compared to uncoated carbide (1430 HV) is observed and depicts better resistance against abrasion. The low erosion rate was observed in TiN coated insert compared to uncoated carbide. The tool life of TiN coated insert is found to be approximately 30 times higher than the uncoated carbide insert under similar cutting conditions and produced lower surface roughness compared to uncoated carbide insert. The dominant wear mechanism was found to be abrasion and progression of wear was steady using multilayer TiN coated carbide insert. The developed regression model shows high determination coefficient i.e. R² = 0.977 for flank wear and 0.94 for surface roughness and accurately explains the relationship between the responses and the independent variable. The machining cost per part for uncoated carbide insert is found to be 10.5 times higher than the multilayer TiN coated carbide inserts. This indicates 90.5% cost savings using multilayer TiN coated inserts by the adoption of a cutting speed of 200 m/min coupled with a tool feed rate of 0.21 mm/rev and depth of cut of 0.4 mm. Thus, TiN coated carbide tools are capable of reducing machining costs and performs better than uncoated carbide inserts in machining D2 steel.     

Modeling and optimization of Al/SiCp MMC machining using Taguchi approach

This paper presents the influence of process parameters like cutting speed, feed and depth of cut on flank wear (VBc) and surface roughness (Ra) in turning Al/SiCp metal matrix composites using uncoated tungsten carbide insert under dry environment. The experiments have been conducted based on Taguchi’s L₉ orthogonal array. Abrasion and adhesion are observed to be the principal wear mechanism from images of tool tip. No premature tool failure by chipping and fracturing was observed and machining was steady using carbide insert. Built-up-edge formation is noticed at low and higher cutting speed and at high feed combination and consequently surface quality affected adversely. The optimal parametric combination for flank wear and surface roughness are found to be v1–f1–d3 and v3–f1–d3 respectively and is greatly improved through Taguchi approach. Mathematical models for flank wear and surface roughness are found to be statistically significant.     

Determining the effect of cutting parameters on surface roughness in hard turning using the Taguchi method

This study focuses on optimizing turning parameters based on the Taguchi method to minimize surface roughness (Ra and Rz). Experiments have been conducted using the L9 orthogonal array in a CNC turning machine. Dry turning tests are carried out on hardened AISI 4140 (51 HRC) with coated carbide cutting tools. Each experiment is repeated three times and each test uses a new cutting insert to ensure accurate readings of the surface roughness. The statistical methods of signal to noise ratio (SNR) and the analysis of variance (ANOVA) are applied to investigate effects of cutting speed, feed rate and depth of cut on surface roughness. Results of this study indicate that the feed rate has the most significant effect on Ra and Rz. In addition, the effects of two factor interactions of the feed rate-cutting speed and depth of cut-cutting speed appear to be important. The developed model can be used in the metal machining industries in order to determine the optimum cutting parameters for minimum surface roughness.     

Process investigation on meso-scale hard milling of ZrO2 by diamond coated tools

This paper investigates the feasible machining of zirconium oxide (ZrO₂) ceramics, in the hard state, via milling by diamond coated miniature tools (from here on briefly indicated as meso-scale hard milling). The workpiece material is a fully sintered yttria stabilized tetragonal zirconia polycrystalline ceramic (Y-TZP). Diamond coated WC mills, 2 mm in diameter, four flutes and large corner radius (0.5 mm) are chosen as cutting tools, and experiments are conducted on a state-of-the-art micro milling machine centre. The influence of cutting parameters, including axial depth of cut (a_p) and feed per tooth (f_z), on the achievable surface quality is studied by means of a one-factor variation experimental design. Further tests are also conducted to monitor the process performance, including surface roughness, tool wear and machining accuracy, over the machining time. Mirror quality surfaces, with average surface roughness Ra below 80 nm, are obtained on the machined samples; the SEM observations of the surface topography reveal a prevailing ductile cutting appearance. Tool wear initiates with delamination of the diamond coating and progresses with the wear of the WC substrate, with significant effect on the cutting process and its performance. Main applications of this research include three dimensional surface micro structuring and superior surface finishing.     

Comparative assessment of wiper and conventional ceramic tools on surface roughness in hard turning AISI 4140 steel

This study considers the comparison between the surface roughness criteria (Ra, Rz and Rt) of the wiper inserts with conventional inserts during hard turning of AISI 4140 hardened steel (60 HRC).The planning of experiments was based on Taguchi’s L₂₇ orthogonal array. The response surface methodology (RSM) and analysis of variance (ANOVA) were used to check the validity of quadratic regression model and to determine the significant parameter affecting the surface roughness. The statistical analysis reveals that the feed rate and depth of cut have significant effects in reducing the surface roughness. The optimum machining conditions to produce the best possible surface roughness in the range of this experiment under these experimental conditions searched using desirability function approach for multiple response factors optimization. The results indicate that the surface quality obtained with the wiper ceramic insert significantly improved when compared with conventional ceramic insert is 2.5. Roughness measurements reveal a dependence on CC6050WH tool wear. However, although the wear rises up to the allowable flank wear of value 0.3 mm, roughness Ra did not exceeded 0.9 μm.     

Optimization of surface roughness and tool wear in hard turning of austempered ductile iron (grade 3) using Taguchi method

In this work, the cutting parameters are optimized in hard turning of ADI using carbide inserts based on Taguchi method. The cutting insert CVD coated with AL₂O₃/MT TICN. Experiments have been carried out in dry condition using L₁₈ orthogonal array. The cutting parameters selected for machining are cutting speed, feed rate and depth of cut with each three levels, nose radius in two levels maintaining other cutting parameters constant. The ANOVA and signal to noise ratio are used to optimize the cutting parameters. The cutting speed is the most dominant factor affecting the surface roughness and tool wear. In optimum cutting condition, the confirmation tests are carried out. The optimum cutting condition results are predicted using signal to noise ratio and regression analysis. The predicted and experimental values for surface roughness and tool wear adhere closer to 9.27% and 1.05% of deviations respectively.     

Comparative study on tool life and wear resistance of titanium nitride (TiN) and aluminium chromium nitride (AlCrN) coated carbide inserts

Abstract

The objective of this study is to investigate the enhancement of tool life and wear resistance with a physical vapour deposition (PVD) process applied using aluminium chromium nitride (AlCrN) and titanium nitride (TiN) coating on carbide inserts. Flank wear experiments are carried out on a computer numerically controlled (CNC) machine under wet conditions with both the coated inserts. Effectiveness of the coating on the tool life and its resistance to flank wear are observed at various cutting parameters such as cutting speed and feed rate by following the principle of design of experiments (DOE). It is inferred that AlCrN coated carbide tools perform nearly 70% better than the TiN coated carbide tools under high cutting speed and feed rate. AlCrN coating also enhances the durability of tool for metal cutting and thereby improves tool life even under harsh cutting conditions. A response surface methodology (RSM) is utilised to arrive at the optimum value for the various parameters which are responsible for improving the wear resistance and tool life.     

Some studies on hard turning of AISI 4340 steel using multilayer coated carbide tool

Hard turning with multilayer coated carbide tool has several benefits over grinding process such as, reduction of processing costs, increased productivities and improved material properties. The objective was to establish a correlation between cutting parameters such as cutting speed, feed rate and depth of cut with machining force, power, specific cutting force, tool wear and surface roughness on work piece. In the present study, performance of multilayer hard coatings (TiC/TiCN/Al₂O₃) on cemented carbide substrate using chemical vapor deposition (CVD) for machining of hardened AISI 4340 steel was evaluated. An attempt has been made to analyze the effects of process parameters on machinability aspects using Taguchi technique. Response surface plots are generated for the study of interaction effects of cutting conditions on machinability factors. The correlations were established by multiple linear regression models. The linear regression models were validated using confirmation tests. The analysis of the result revealed that, the optimal combination of low feed rate and low depth of cut with high cutting speed is beneficial for reducing machining force. Higher values of feed rates are necessary to minimize the specific cutting force. The machining power and cutting tool wear increases almost linearly with increase in cutting speed and feed rate. The combination of low feed rate and high cutting speed is necessary for minimizing the surface roughness. Abrasion was the principle wear mechanism observed at all the cutting conditions.     

Experimental investigation and performance analysis of cemented carbide inserts of different geometries using Taguchi based grey relational analysis

In this work, effect of machining parameters cutting speed, feed rate and depth of cut, geometrical parameters cutting insert shape, relief angle and nose radius were investigated and optimized using Taguchi based grey relational analysis. 18 ISO designated uncoated cemented carbide inserts of different geometries were used to turn practically used automotive axles to study the influence of variation in carbide inserts geometry. Performance measures viz., flank wear, surface roughness and material removal rate (MRR) were optimized using grey relational grade, based on the experiments designed using Taguchi’s Design of Experiments (DoE). A weighted grey relational grade is calculated to minimize flank wear and surface roughness and to maximize MRR. Analysis of variance shows that cutting insert shape is the prominent parameter followed by feed rate and depth of cut that contributes towards output responses. An experiment conducted with identified optimum condition shows a lower flank wear and surface roughness with higher MRR. The confirmation results obtained are confirmed by calculating confidence interval, which lies within the width of the interval.     

Investigation of the performance of carbide cutting tools with hard coatings in hard milling based on the response surface methodology

Machining of hard materials has become a great challenge for several decades. One of the problems in this machining process is early tool wear, and this affects the machinability of hard materials. In order to increase machinability, cutting tools are widely coated with nanostructured physical vapor deposition hard coatings. The main characteristics of such advanced hard coatings are high microhardness and toughness as well as good adhesion to the substrate. In this paper, the influence of hard coatings (nanolayer AlTiN/TiN, multilayer nanocomposite TiAlSiN/TiSiN/TiAlN, and commercially available TiN/TiAlN) and cutting parameters (cutting speed, feed rate, and depth of cut) on cutting forces and surface roughness were investigated during face milling of AISI O2 cold work tool steel (～61 HRC). The experiments were conducted based on 3¹³ factorial design by response surface methodology, and response surface equations of cutting forces and surface roughness were obtained. In addition, the cutting forces obtained with the coated and uncoated tools were compared. The results showed that the interaction of coating type and depth of cut affects surface roughness. The hard coating type has no significant effect on cutting forces, while the cutting force F _z is approximately two times higher in the case of uncoated tool.     

Effects of Coating Materials on the Machinability of a Nickel Base,C-263, Alloy

PVD coated (TiN/TiCN/TiN, TiAIN and TiZrN) and uncoated carbide tools were used to machine a nickel base, C-263, alloy at high-speed conditions. The test results show that the multiple TiN/TiCN/TiN coated inserts gave the best overall performance in terms of tool life when machining at cutting speeds up to 68 m min and at depths of cut of 0.635 mm, 1.25 mm and 2.54 mm. All the tool grades tested gave fairly uniform surface roughness (Ra) values, below the rejection criterion, at lower speed conditions. The TiZrN coated inserts gave the lowest component forces when machining at lower cutting speed conditions while the TiA/N coated inserts gave the lowest component forces when machining at a higher speed of 68 m min^?1 and depth of cut of 1.25 mm. This tool performance can generally be attributed to the difference in their ability to provide effective lubrication at the cutting zone, thermal conductivity of the coating materials as well as the cutting conditions employed. The uncoated carbide tools generally encountered more severe crater wear, chipping/fracture of the cutting edges as well as pronounced notching during machining. This is due to their inability to provide effective lubrication at the cutting zone, thus impeding the gliding motion of the chips along the rake and flank faces respectively, thus accelerating flank wear. Analysis of the worn tool edges revealed adhesion of a compact “fin-shaped” structure of hardened burrs with saw-tooth like edges. This generally alters the initial geometry of the cutting edge, consequently resulting to poor surface finish with prolonged machining.     

Optimization of surface roughness and flank wear using the Taguchi method in milling of Hadfield steel with PVD and CVD coated inserts

In this paper, the Taguchi method and regression analysis have been applied to evaluate the machinability of Hadfield steel with PVD TiAlN- and CVD TiCN/Al₂O₃-coated carbide inserts under dry milling conditions. Several experiments were conducted using the L₁₈ (2 × 3 × 3) full-factorial design with a mixed orthogonal array on a CNC vertical machining center. Analysis of variance (ANOVA) was used to determine the effects of the machining parameters on surface roughness and flank wear. The cutting tool, cutting speed and feed rate were selected as machining parameters. The analysis results revealed that the feed rate was the dominant factor affecting surface roughness and cutting speed was the dominant factor affecting flank wear. Linear and quadratic regression analyses were applied to predict the outcomes of the experiment. The predicted values and measured values were very close to each other. Confirmation test results showed that the Taguchi method was very successful in the optimization of machining parameters for minimum surface roughness and flank wear in the milling the Hadfield steel.     

Comparative evaluation of machinability characteristics of Nimonic C-263 using CVD and PVD coated tools

Machining of Nimonic C-263 has always been a challenging task owing to its hot strength, low thermal conductivity, tendency to work harden and affinity towards tool materials. Although coated tools have been used to overcome some of these challenges, selection of coated tool with appropriate deposition technique is of immense significance. The current study attempts to comparatively evaluate various performance measures in machining of Nimonic C-263 such as surface roughness, cutting force, cutting temperature, chip characteristics, and tool wear with particular emphasis on different modes of tool failure for commercially available inserts with multi-component coating deposited using chemical vapour deposition (CVD) and physical vapour deposition (PVD) techniques. Influence of cutting speed (V_c) and machining duration (t) has also been investigated using both coated tools. The study demonstrated remarkable decrease in surface roughness (74.3%), cutting force (6.3%), temperature (13.4%) and chip reduction coefficient (22%) with PVD coated tool consisting of alternate layers of TiN and TiAlN over its CVD coated counterpart with TiCN/Al₂O₃ coating in bilayer configuration. Severe plastic deformation and chipping of cutting edge and nose, abrasive nose and flank wear along with formation of built-up-layer (BUL) were identified as possible mechanisms of tool failure. PVD coated tool successfully restricted different modes of tool wear for the entire range of cutting speed. Superior performance can be attributed to the hardness and wear resistance properties, thermal stability due to presence of TiAlN phase and excellent toughness owing to PVD technique and multilayer architecture.     

Wear behavior of some cutting tool materials in hard turning of HSS

This study presents an assessment of the performance of four cutting tool in the machining of medium hardened HSS: polycrystalline c-BN (c-BN+TiN), TiN coated polycrystalline c-BN (c-BN+TiN), ceramic mixed alumina (Al₂O₃+TiC), and coated tungsten carbide (TiN coated over a multilayer coating (TiC/TiCN/Al₂O₃)). The Al₂O₃+TiC and the coated carbide tools can outperform both types of c-BN at high cutting speeds. Raman and SEM mapping revealed an alumina tribo-layer that protects the surface of the Al₂O₃+TiC cutting tool. The high chemical and thermal stability of Al₂O₃ tribo-films protects the tool substrate because it prevents the heat generated at the tool/chip interface from entering the tool core.     

Residual stresses in TiN, DLC and MoS2 coated surfaces with regard to their tribological fracture behaviour

Thin hard coatings on components and tools are used increasingly due to the rapid development in deposition techniques, tribological performance and application skills. The residual stresses in a coated surface are crucial for its tribological performance. Compressive residual stresses in PVD deposited TiN and DLC coatings were measured to be in the range of 0.03-4 GPa on steel substrate and 0.1-1.3 GPa on silicon. MoS₂ coatings had tensional stresses in the range of 0.8-1.3 on steel and 0.16 GPa compressive stresses on silicon. The fracture pattern of coatings deposited on steel substrate were analysed both in bend testing and scratch testing. A micro-scale finite element method (FEM) modelling and stress simulation of a 2 μm TiN-coated steel surface was carried out and showed a reduction of the generated tensile buckling stresses in front of the sliding tip when compressive residual stresses of 1 GPa were included in the model. However, this reduction is not similarly observed in the scratch groove behind the tip, possibly due to sliding contact-induced stress relaxation. Scratch and bending tests allowed calculation of the fracture toughness of the three coated surfaces, based on both empirical crack pattern observations and FEM stress calculation, which resulted in highest values for TiN coating followed by MoS₂ and DLC coatings, being K_C = 4-11, about 2, and 1-2 MPa m^1/2, respectively. Higher compressive residual stresses in the coating and higher elastic modulus of the coating correlated to increased fracture toughness of the coated surface.     

Performance of coated and uncoated mixed ceramic tools in hard turning process

The present contribution deals with the study of the effects of cutting speed, feed rate and depth of cut on the performance of machining which traditionally named “machinability”. The focus is made on the effect of the pre-cited cutting parameters on the evolution of surface roughness and cutting force components during hard turning of AISI D3 cold work tool steel with CC6050 and CC650 ceramic inserts. Also, for both ceramics a comparison of their wear evolution with time and its impact on the surface equality was proposed. The planning of experiments was based on Taguchi’s L₁₆ orthogonal array. The analysis of variance (ANOVA), the signal-to-noise ratio and response surface methodology (RSM) were adopted. Consequently, the validity of proposed linear regression model was checked and the most important parameter affecting the surface roughness and cutting force components were determined. Furthermore, in order to determine the levels of the cutting regime that lead to minimum surface roughness and minimum machining force the relationship between cutting factors was analyzed. The results revealed that the surface quality obtained with the coated CC6050 ceramic insert is 1.6 times better than the one obtained with uncoated CC650 ceramic insert. However, the uncoated ceramic insert was useful in reducing the machining force.     

Performance of Uncoated and Coated Carbide Tools in the Ultra-Precision Machining of Stainless Steel

Ultra-precision machines are widely used to turn aspherical or spherical profiles on mould inserts for the injection moulding of optical lenses. During the turning of a profile on a stainless steel mould insert, the cutting speed reduces significantly to 0 as the cutting tool is fed towards the centre of the machined profile. This paper reports experiments carried out to study the wear of uncoated and PVD-coated carbide tools (carbide tool coated with 2000 alternate layers of AlN and TiN, each layer 1.5 nm and carbide tool coated with 0.5 m TiN, 5.5 m TiCN and 0.5 m TiN) in the ultra-precision machining of STAVAX (modified AISI 420 stainless steel) at low speeds with and without lubricant. A sprayed mixture of compressed air, liquid paraffin oil and cyclomethicone was used as lubricant. Examination of the wear at the rake face of the tool suggests that during machining of the alloy with a hardness of 55 HRC without lubricant, the cutting edge is subjected to high compressive stress, resulting in fracture. Reducing the hardness of the alloy would therefore result in a lower stress acting on the cutting edge, thus rendering the tool less susceptible to fracture. Both the rake and the flank faces of the coated tools exhibited lower wear than the uncoated tools. This was due to the former tools possessing higher fracture resistance owing to the presence of the coating. The lubricant was effective in improving surface finish, preventing surface fracture and reducing flank wear.     

Multi response optimisation of CNC turning parameters via Taguchi method-based response surface analysis

This study presents a new method to determine multi-objective optimal cutting conditions and mathematic models for surface roughness (Ra and Rz) on a CNC turning. Firstly, cutting parameters namely, cutting speed, depth of cut, and feed rate are designed using the Taguchi method. The AISI 304 austenitic stainless workpiece is machined by a coated carbide insert under dry conditions. The influence of cutting speed, feed rate and depth of cut on the surface roughness is examined. Secondly, the model for the surface roughness, as a function of cutting parameters, is obtained using the response surface methodology (RSM). Finally, the adequacy of the developed mathematical model is proved by ANOVA. The results indicate that the feed rate is the dominant factor affecting surface roughness, which is minimized when the feed rate and depth of cut are set to the lowest level, while the cutting speed is set to the highest level. The percentages of error all fall within 1%, between the predicted values and the experimental values. This reveals that the prediction system established in this study produces satisfactory results, which are improved performance over other models in the literature. The enhanced method can be readily applied to different metal cutting processes with greater confidence.