Synthesis of acrylamide/acrylic acid‐based aluminum flocculant for dye reduction and textile wastewater treatment

Aluminum hydroxide‐poly[acrylamide‐co‐(acrylic acid)], AHAMAA, was synthesized with a redox initiator by solution polymerization in which the effects of reactant contents were optimized. The effects of pH, temperature, and initial dye concentration on Congo red reduction were investigated. A mixture of Congo red and direct blue 71, and the composite textile dye wastewater were investigated. Adsorptions of both dyes were more effective in the nonbuffered solution than those in the buffered solution, and Congo red adsorbed more than direct blue 71 at all pHs. The adsorption of Congo red increased with increasing temperature and its initial concentration. Both dyes obeyed the Freundlich adsorption isotherm. The maximum adsorptions in 100 mg dm^?3 solution were 109 ± 0.5 mg g^?1 and 62 ± 6.6 mg g^?1 for Congo red and direct blue 71, respectively. At 150 mg dm^?3 of the mixed Congo red and direct blue 71, the adsorption was 142 ± 2 mg g^?1 by 643 ± 3 mg dm^?3 AHAMAA. The 40 mg g^?1 dyes of the textile effluent wastewater were adsorbed by 500 mg dm^?3 AHAMAA. AHAMAA could decrease turbidity of the composite wastewater containing a mixture of reactive and direct dyes from 405 to 23 NTU. POLYM. ENG. SCI., 50:1535–1546, 2010. © 2010 Society of Plastics Engineers     

Multifunctional amphoteric resin to remove both anionic and cationic dyes from aqueous solution

This study reports the synthesis and characterization of a new amphoteric resin, which can be used for the removal of both cationic, methylene blue (MB) and anionic dyes, reactive red-120 (RR-120). The amphoteric resin was characterized by ATR-FTIR, SEM–EDX, TGA/DTA, DLS, BET analysis and also its surface pHpzc was determined. The prepared resin has micro porous structure and its particle size was at the nano level. The prepared amphoteric resin showed high removal affinity for MB in both acidic and basic medium, while for RR-120 high removal affinity in acidic medium. Moreover, it was observed that the amphoteric resin has exhibited almost 100% dye removal up to 600 ppm for MB and up to 300 ppm for RR-120, respectively. The adsorption behavior of both dyes on the amphoteric resin is in agreement with the Langmuir isotherm and the pseudo-second order kinetic model and also electrostatic interaction is dominant in adsorption. Its capacity was slightly low for the MB than that of the commercial activated carbon, but higher for the RR-120. Furthermore, it was observed that the amphoteric resin almost did not lose its high removal efficiency in the concentrated matrix environment for both dyes. After five repeated adsorption–desorption cycles, the high removal efficiency of the resin for the MB (almost 100%) unchanged, but for the RR-120 decreased to 83%.     

SYNTHESIS AND CHARACTERIZATION OF CADMIUM SULFIDE NANOPARTICLE–LOADED ACTIVATED CARBON AS A NOVEL ADSORBENT FOR EFFICIENT REMOVAL OF REACTIVE ORANGE 12

The objective of this study was to evaluate the adsorption potential of cadmium sulfide nanoparticle–loaded activated carbon (CdSN-AC) for removal of reactive orange 12 (RO-12) dyestuffs from aqueous solutions. The characterization of CdSN-AC was performed by X-ray diffraction (XRD), transmission electron microscopy (TEM), and field emission scanning electron microscopy (FESEM) techniques. The effects of experimental parameters such as initial solution pH, contact time, initial RO-12 concentration, amount of CdSN-AC, and temperature on the adsorption process were evaluated in detail. The kinetic studies indicated that the adsorption process was best described by the pseudo-second-order kinetics model. The experimental data were analyzed by the Langmuir, Freundlich, and Tempkin isotherm models, and the monolayer adsorption capacity of CdSN-AC was found to be 150.0 mg g^?1 by using the Langmuir isotherm model. The thermodynamic parameters indicated that the adsorption of RO-12 onto CdSN-AC was feasible, spontaneous, and endothermic in nature.     

Dye removal from colored‐textile wastewater using chitosan‐PPI dendrimer hybrid as a biopolymer: Optimization,kinetic, and isotherm studies

Preparation of a biopolymer chitosan‐polypropylene imine (CS‐PPI) as a biocompatible adsorbent and its reactive textile dyes removal potential were performed. Chemical specifications of CS‐PPI were determined using Fourier transform infrared, ¹H‐NMR, and ¹³C‐NMR. The surface morphology of the CS‐PPI surface was characterized by scanning electron microscopy. Results confirmed that the linkages between the NH₂ groups of PPI dendrimer and carboxylic groups of modified Chitosan were accomplished chemically. Two textile reactive dyes, reactive black 5 (RB5) and reactive red 198 (RR198), were used as model compounds. A response surface methodology was applied to estimate the simple and combined effects of the operating variables, including pH, dye concentration, time contact, and temperature. Under the optimal values of process parameters, the dye removal performance of 97 and 99% was achieved for RB5 and RR198, respectively. Furthermore, the isotherm and kinetic models of dyes adsorption were performed. Adsorption data represented that both examined dye followed the Langmuir isotherm. The adsorption kinetics of both reactive dyes were satisfied by pseudo‐second order equation. Based on this study, CS‐PPI due to having high adsorption capacity (6250 mg/g for RB5 and 5882.35 mg/g for RR198), biocompatibility and ecofriendly properties might be a suitable adsorbent for removal of reactive dyes from colored solutions. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Sodic and Acidic Crystalline Lamellar Magadiite Adsorbents for the Removal of Methylene Blue from Aqueous Solutions: Kinetic and Equilibrium Studies

The present study reports the feasibility of two synthetic crystalline lamellar nano-silicates, sodic magadiite (Na-mag) and its converted acidic form (H-mag), as alternative adsorbents for the removal of the dye methylene blue (MB) from aqueous solutions. The ability of these adsorbents for removing the dye was explored through the batch adsorption procedure. Effects such as the pH and the adsorbent dosage on the adsorption capacities were explored. Four kinetic models were applied, the adsorption being best fitted to a fractionary-order kinetic model. The kinetic data were also adjusted to an intra-particle diffusion model to give two linear regions, indicating that the kinetics of adsorption follows multiple sorption rates. The equilibrium data were fitted to Langmuir, Freundlich, Sips, and Redlich-Peterson isotherm models. The maxima adsorption capacities for MB of Na-mag and H-mag were 331 and 173 mg g^?1, respectively.     

Equilibrium Isotherms,Thermodynamics, and Kinetic Studies for the Adsorption of Food Azo Dyes onto Chitosan Films

The adsorption of FD&C red 2 and FD&C yellow 5 onto chitosan films (CFs) was evaluated by equilibrium isotherms, thermodynamics, and kinetic studies. The effects of temperature (298–328 K), initial dye concentration (50–300 mg L^?1), stirring rate (50–350 rpm), and contact time (0–120 min) were investigated at pH of 2.0 and 100 mg L^?1 of CFs. The dye concentration was determined by spectrophotometry. Freundlich and Langmuir models were used to represent the equilibrium data. The Langmuir model was the more adequate to represent the equilibrium data (R² > 0.99 and average relative error <2.50%) and the maximum adsorption capacities were 494.13 and 480.00 mg g^?1 for FD&C red 2 and FD&C yellow 5, respectively, obtained at 298 K. The R_L values ranged from 0.044 to 0.145. The adsorption was exothermic, spontaneous, and favorable. For the FD&C red 2, 90% of saturation was attained at 120 min and the Elovich model was the more appropriate. For the FD&C yellow 5, 95% of saturation was attained at 20 min and the pseudo first-order model was the more adequate to fit the kinetic data. CFs were easily separated from the liquid phase after the adsorption process, providing benefits for industrial applications, and its application range can be extended for azo dyes.     

Palladium,silver, and zinc oxide nanoparticles loaded on activated carbon as adsorbent for removal of bromophenol red from aqueous solution

The adsorption of bromophenol red (BPR) onto three adsorbents including palladium, silver and zinc oxide nanoparticles loaded on activated carbon (Pd-NP-AC, Ag-NP-AC and ZnO-NP-AC) in a batch system has been studied and the influence of various parameters has been optimized. The influence of time on removal of BPR on all adsorbent was investigated and experimental data were analyzed by four kinetic models including pseudo first and second-order, Elovich and the intraparticle diffusion equations. Following fitting the experimental data to these models, the respective parameters of each model such as rate constants, equilibrium adsorption capacities and correlation coefficients for each model were investigated and based on well known criterion their applicability was judged. It was seen that the adsorption of BPR onto all adsorbents sufficiently described by the pseudo second-order equation in addition to interparticle diffusion model. The adsorption of BPR on all adsorbent was investigated at various concentration of dye and the experimental equilibrium data were analyzed and fitted to the Langmuir, Freundlich, Tempkin, Dubinin, and Radushkevich equations. A single stage in batch process was efficient and suitable for all adsorbents using the Langmuir isotherm with maximum adsorption of 143 mg g^?1 for Pd-NP-AC, 250 mg g^?1 for Ag-NP-AC and 200 mg g^?1 for ZnO-NR-AC. Thermodynamic parameters such as ΔG°, ΔH°, and ΔS° for Pd-NP-AC adsorbent were calculated.     

Adsorption of anionic dye on eco-friendly synthesised reduced graphene oxide anchored with lanthanum aluminate: Isotherms,kinetics and statistical error analysis

In the present study we made an effort to deploy eco-friendly synthesized reduced graphene oxide/Lanthanum Alluminate nanocomposites (RGO-LaAlO₃) and Lanthanum Alluminate (LaAlO₃) as adsorbents to remove dye from the synthetic media. XRD, SEM, BET surface area and EDX have been used to characterize the above-mentioned adsorbents. The impacts of different factors like adsorbent dosage, the concentration of adsorbate and PH on adsorption were studied. The best fit linear and nonlinear equations for the adsorption isotherms and kinetic models had been examined. The sum of the normalized errors and the coefficient of determination were used to determine the best fit model. The experimental data were more aptly fitted for nonlinear forms of isotherms and kinetic equations. Pseudo-second-order and Freundlich isotherm model fits the equilibrium data satisfactorily. Methyl orange (MO) has been used as model dye pollutant and maximum adsorption capacity was found to be 469.7 and 702.2 mg g^?1 for LaAlO₃ and RGO-LaAlO₃, respectively.     

Removal of Reactive Blue 21 onto magnetic chitosan microparticles functionalized with polyamidoamine dendrimers

Chitosan/poly(amidoamine) (MCS/PAMAM) microparticles were prepared as magnetic adsorbents for removal of Reactive Blue 21 (RB 21) dye from aqueous solution. Characterization of these particles was carried out using scanning electron microscopy, Fourier transform-infrared spectroscopy, X-ray diffractometry and vibrating sample magnetometry. The results indicate that the magnetic chitosan microparticles (MCS) were functionalized with PAMAM dendrimers and maintained its intrinsic magnetic properties. The effects of initial pH, adsorbent dose, initial concentration, contact time and temperature on adsorption were investigated. Kinetic studies showed that the dye adsorption process followed a pseudo-second-order kinetic model but that the adsorption rate was also influenced by intraparticle diffusion. Equilibrium adsorption isotherm data indicated a good fit to the Langmuir isotherm. The maximum adsorption capacities obtained from the Langmuir model were 555.56, 588.24, 625.00 and 666.67 mg g⁻¹ at 303, 313, 323 and 333 K, respectively. The thermodynamic parameters revealed the feasibility, spontaneity and endothermic nature of the adsorption. Recycling experiments confirmed the relative reusability of the adsorbent.     

ADSORPTION,KINETICS, AND EQUILIBRIUM STUDIES ON REMOVAL OF 4,4-DDT FROM AQUEOUS SOLUTIONS USING LOW-COST ADSORBENTS

The removal of a chlorinated pesticide (4,4-DDT) from aqueous solutions by a batch adsorption technique using different low-cost adsorbents was investigated. Two adsorbents, wood sawdust (A) and cork wastes (B), were used to determine adsorption efficiency. The influence of the adsorbent particle size and the organic matter of water (humic acids) on the removal process was studied. The obtained results were compared to those obtained with a commercial powdered activated carbon (PAC, F400, Chemviron) (C). Kinetic studies were performed to understand the mechanistic steps of the adsorption process. The rate of the adsorption kinetics of 4,4-DDT on the low-cost adsorbents was found best fitted with a pseudo-second-order kinetic model. This is in contrast to the rate of the adsorption kinetics of the PAC F400, which was best fitted with the Lagergren model. The application of the Morris-Weber equation showed that the adsorption process of 4,4-DDT on these adsorbents was complex. Both the adsorption on the surface and the intraparticle diffusion were the rate-controlling mechanisms. Langmuir and Freundlich adsorption isotherms were applicable to the adsorption process and their constants were evaluated. The adsorption capacity (q_m) calculated from the Langmuir isotherm (69.44 mg·g^?1, 19.08 mg·g^?1, and 163.90 mg·g^?1, respectively, for A, B, and C) showed that the process is highly particle size dependent, that the organic matter influenced the adsorption process negatively, and that wood sawdust is the most effective adsorbent for the removal of 4,4-DDT from aqueous solutions. The adsorbents studied exhibited a possible application in water decontamination, as well as in treatment of industrial and agricultural waste waters.     

Equilibrium,kinetic and thermodynamic study of removal of reactive orange 12 on platinum nanoparticle loaded on activated carbon as novel adsorbent

The proposed research describes the synthesis and characterization of platinum nanoparticles loaded on activated carbon (Pt-NP-AC) and its efficient application as novel adsorbent for efficient removal of reactive orange 12 (RO-12). The influences of effective parameters following the optimization of variables on removal percentages, their value was set as 0.015 g Pt-NP-AC, pH 1, contact time of 13 min. At optimum values of all variables at 25 and 50 mgL⁻¹ of RO-12 enthalpy (ΔH⁰) and entropy (ΔS⁰) changes was found to be 59.89 and 225.076, respectively, which negative value of ΔG⁰ shows a spontaneous nature, and the positive values of ΔH⁰ and ΔS⁰ indicate the endothermic nature and adsorption organized of dye molecule on the adsorbent surface. Experimental data was fitted to different kinetic models including first-order, pseudo-second-order, Elovich and intra-particle diffusion models, and it was seen that the adsorption process follows pseudo-second-order model in consideration to intra-particle diffusion mechanism. At optimum values of all variables, the adsorption process follows the second-order kinetic and Langmuir isotherm model with adsorption capacity 285.143 mg g⁻¹ at room temperature.     

Adsorption behavior of methylene blue on amine-functionalized ordered mesoporous alumina

Amine-functionalized ordered mesoporous alumina (NH₂-OMA) was synthesized through a facile and reproducible method. Its organic dyes adsorption characteristics, including adsorption isotherms, adsorption kinetics, the stability and reusability of the adsorbents were investigated. This material exhibited strong affinity to methylene blue and extremely high adsorption capacity. The maximum adsorption capacity value reached 657.89 mg g^?1. Adsorption kinetics was best described by the pseudo-second-order model. Equilibrium data were well fitted to the Langmuir isotherm model.     

Removal of Orange II from Aqueous Solutions Using N-Vinyl Imidazole-based Hydrogels as Adsorbents

Poly(N-vinyl imidazole) hydrogel (p-VIm) and its partially quaternized analogue (p-VIm-Ar) were prepared and used for the removal of Orange II (OII). A fourier transform infrared spectrophotometer, scanning electron microscope with an energy dispersive X-ray spectrometer attached, thermogravimetric analyzer, zeta potential analyzer, and a drop shape analyzer were used for the characterization of the hydrogels. The influence of some experimental parameters, such as pH of the OII solution, contact time, and initial OII concentration on the adsorption process, was examined, and the obtained data were used to calculate the isotherm and kinetic parameters. Adsorption processes of OII onto adsorbents were coherent with the Langmuir isotherm and pseudo-second-order kinetic models. The quaternized analogue exhibited remarkable adsorption performance in the pH range of 2–12, while the effective adsorption with p-VIm occurred only at pH 2.0. The maximum adsorption capacity values of adsorbents were determined as 2331 (for p-VIm) and 1327 mg g^?1 (for p-VIm-Ar) at pH 2.0 and 132 (for p-VIm) and 1357 mg g^?1 (for p-VIm-Ar) at pH 6.0.     

Application of Aqai Stalks as Biosorbents for the Removal of the Dye Procion Blue MX-R from Aqueous Solution

The aqai palm stalk (Euterpe oleracea) is a food residue used in its natural form (AS) and also protonated (AAS) as biosorbents for the removal of the textile dye Procion Blue MX-R from aqueous solutions. This biosorbent was characterized by infrared spectroscopy, scanning electron microscopy, and nitrogen adsorption-desorption curves. The effects of pH, biosorbent dosages, and shaking time on the biosorption capacities were studied. In the acidic pH region (pH 2.0) the biosorption of the dye was favorable. The minimum contact time to obtain the equilibrium was 8 hours for AS and AAS biosorbents. The general order kinetic model provided the best fit to the experimental data compared with the pseudo-first order and pseudo-second order kinetic adsorption models. The equilibrium data were fitted to the Langmuir, Freundlich, and Sips isotherm models. For both dyes the equilibrium data were best fitted to the Sips isotherm model. The enthalpy and entropy of adsorption of PB were obtained from adsorption equilibrium experiments ranging from 298 to 323 K. Simulated dyehouse effluent was used to check the applicability of the proposed adsorbents for effluent treatment.     

Adsorption of different dyes from aqueous solution using Si-MCM-41 having very high surface area

Adsorption characteristics of four different dyes Safranin O (cationic), Neutral Red (neutral), Congo Red (anionic) and Reactive Red 2 (anionic) on Si-MCM-41 material having very high surface area are reported. The surface morphology of Si-MCM-41 material before and after adsorbing dye molecules are characterised by FTIR, HRXRD, nitrogen adsorption–desorption isotherms, FESEM, and HRTEM. The adsorption capacities of Si-MCM-41 for the dyes followed a decreasing order of NR > SF > CR > RR2. The adsorption kinetics, isotherm and thermodynamic parameters are investigated in detail for these dyes using calcined Si-MCM-41. The kinetics and isotherm data showed that both SF and NR adsorb more rapidly than CR and RR2, in accordance with pseudo-second-order kinetics model as well as intraparticle diffusion kinetics model and Langmuir adsorption isotherm model respectively. The thermodynamic data suggest that the dye uptake process is spontaneous. The high adsorption capacities of dyes on Si-MCM-41 (q_m = 275.5 mg g^?1 for SF, q_m = 288.2 mg g^?1 for NR) is explained on the basis of electrostatic interactions as well as H-bonding interactions between adsorbent and adsorbate molecules. Good regeneration capacity is another important aspect of the material that makes it potent for the uptake of dyes from aqueous solution.     

Preparation of poly (acrylic acid) containing core‐shell type resin for removal of basic dyes

BACKGROUND: A core‐shell type carboxylic acid modified resin was prepared and dye sorption characteristics of the resin were investigated. The resulting grafted resin material has been shown to be an efficient sorbent for removal of basic dyes from water as a result of the carboxylic acid group's affinity towards basic dye molecules. RESULTS: The resin was characterized using Fourier transform infrared spectroscopy (FT‐IR) and titrimetric methods. The basic dyes (methylene blue and crystal violet) were removed by contacting the swollen resin with aqueous dye solutions at room temperature. The adsorption capacities of resin were determined by colorimetric analysis of the residual dye content in the adsorption medium, which gave capacities for methylene blue and crystal violet of 300 and 250 mg g^?1 resin, respectively. The prepared resin is also able to remove basic dyes completely from dilute aqueous dye solutions. Batch kinetic sorption experiments determined that a pseudo‐second‐order rate kinetic model was applicable. CONCLUSION: Flexibility of the polymer side chains is expected to provide pseudo‐homogeneous reaction conditions and easy accessibility of the functional groups involved. The adsorbents are expected to have the advantage of mobility of the grafted chains in the removal of basic dyes from aqueous mixtures. The resin has potential as an adsorbent for removal of basic dyes for use over a wide pH range. Copyright © 2011 Society of Chemical Industry     

Poly(PEI-catechol-tetraethylenepentamine) was prepared by “one-pot method” for removing Reactive Red 195

Wastewater containing dyes is frequently discharged by industrial processes and needs separation and recycling. To solve this problem, it is important to research and develop environmentally friendly, efficient adsorbent materials for pollutant separation and recovery. In this study, a poly(PEI-catechol-tetraethylenepentamine) (PPCT) adsorbent was synthesized using a simple catecholamine reaction. This adsorbent exhibited high adsorption capacity and excellent removal efficiency for Reactive Red 195 (RR-195) in wastewater. The material was characterized using SEM, FT-IR, TGA, EA, and XPS. Its performance was optimized by varying the type of polyethyleneimine and the amount added during the preparation process. The effects of temperature, pH, contact time, and salt concentration on the adsorption were systematically investigated. Additionally, the experimental data showed consistency with both the Langmuir and pseudo-second-order kinetic models, simultaneously. The maximum adsorption capacity can reach 1754 mg g⁻¹ at 303 K, with a retention rate of 86.6% after two cycles. The removal rate exceeds 98% at a concentration of 400 mg g⁻¹ or lower. Additionally, the protonated amine group in PPCT carries a positive charge under acidic conditions, enabling selective adsorption of the anionic dye RR-195. Consequently, PPCT exhibits an excellent adsorption effect on RR-195 and holds promising applications in pollutant removal.     

Removal of methylene blue from aqueous solution by adsorption onto zeolite synthesized from coal fly ash and its thermal regeneration

BACKGROUND: The removal of cationic dyes from wastewater is of great importance. Three zeolites synthesized from coal fly ashes (ZFAs) were investigated as adsorbents to remove methylene blue (MB), a cationic dye, from aqueous solutions. Experiments were conducted using the batch adsorption technique under different conditions of initial dye concentration, adsorbent dose, solution pH, and salt concentration. RESULTS: The adsorption isotherm data of MB on ZFAs were fitted well to the Langmuir model. The maximum adsorption capacities of MB by the three ZFAs, calculated using the Langmuir equation, ranged from 23.70 to 50.51 mg g^?1. The adsorption of MB by ZFA was essentially due to electrostatic forces. The measurement of zeta potential indicated that ZFA had a lower surface charge at alkaline pH, resulting in enhanced removal of MB with increasing pH. MB was highly competitive compared with Na⁺, leading to only a < 6% reduction in adsorption in the presence of NaCl up to 1.0 mol L^?1. Regeneration of used ZFA was achieved by thermal treatment. In this study, 90–105% adsorption capacity of fresh ZFA was recovered by heating at 450 °C for 2 h. CONCLUSION: The experimental results suggest that ZFA could be employed as an adsorbent in the removal of cationic dyes from wastewater, and the adsorptive ability of used ZFA can be recovered by thermal treatment. Copyright © 2010 Society of Chemical Industry     

Efficient removal of organic dye pollutants using covalent organic frameworks

A rational design and synthesis of covalent organic frameworks (COFs) displaying efficient adsorption of surrogates for common organic pollutants is demonstrated herein. Significantly, the top performing mesoporous triazine‐functionalized polyimide COF exhibits superior adsorption of the small dye molecule methylene blue, achieving a maximum adsorption capacity of ～1691 mg g^?1 (～169 wt %), surpassing the performance of all previously reported nanoporous adsorbents. The experimental results and accompanying in silico simulations suggest that both the size of the organic dye molecules and the intrinsic pore‐size effect of the COF material should be taken into account simultaneously for the construction of COF‐based adsorbents with efficient dyes adsorption capacities. The structural diversity of COF materials along with the understanding of the encapsulation of organic dyes on COFs holds great promise for developing novel COF adsorbents for the efficient removal of organic pollutants from wastewater. © 2017 American Institute of Chemical Engineers AIChE J, 63: 3470–3478, 2017     

Modeling of Adsorptive Filtration of a Leather Dye in a Fixed Bed Column

Abstract

Activated carbons offer an efficient option for the removal of organic and inorganic contaminants from water. However, due to its high costs and difficulty in the regeneration, other low cost adsorbents have been used. In this work, the adsorption capacity of an adsorbent carbon with high iron oxides concentration was compared with that of a commercial activated carbon in the removal of a leather dye from an aqueous solution. The adsorbents were characterized using SEM/EDAX analysis and BET surface area. The capacity of adsorption of the adsorbents was evaluated through the static method at 25°C. The results showed that the color removal was due to the adsorption and precipitation of the dye on the surface of the solids. The adsorption equilibrium was described according to the linear model for the adsorbent carbon and the equilibrium constant was 0.02 L g^?1. The equilibrium of adsorption on activated carbon exhibited a behavior typical of the Langmuir isotherm and the monolayer coverage was 24.33 mg g^?1. A mathematical model was proposed to describe the dynamics of the color removal using a fixed bed considering that the color removal is due to the adsorption and the precipitation of the dye on the adsorbent.