Combined effect of strength & sheet thickness on fatigue behaviour of resistance spot welded joint

Fatigue performance of spot welded lap shear joint is primarily dependent on weld nugget size, sheet thickness and corresponding joint stiffness. Two automotive steel sheets having higher strength lower thickness and lower strength higher thickness are resistance spot welded with established optimum welding condition. The tensile‐shear strength and fatigue strength of lap shear joint of the two automotive steel sheets are determined and compared. Experimental fatigue life of spot welded lap shear joint of each steel are compared with predicted fatigue lives using different stress intensity factor solutions for kinked crack and spot weld available in literature. Micrographs of fatigue fractured surfaces are examined to understand fracture micro‐mechanisms.     

Stress intensity factor solutions for estimation of fatigue lives of laser welds in lap-shear specimens

Fatigue behavior of laser welds in lap-shear specimens of high strength low alloy (HSLA) steel is investigated based on experimental observations and two fatigue life estimation models. Fatigue experiments of laser welded lap-shear specimens are first reviewed. Analytical stress intensity factor solutions for laser welded lap-shear specimens based on the beam bending theory are derived and compared with the analytical solutions for two semi-infinite solids with connection. Finite element analyses of laser welded lap-shear specimens with different weld widths were also conducted to obtain the stress intensity factor solutions. Approximate closed-form stress intensity factor solutions based on the results of the finite element analyses in combination with the analytical solutions based on the beam bending theory and Westergaard stress function for a full range of the normalized weld widths are developed for future engineering applications. Next, finite element analyses for laser welded lap-shear specimens with three weld widths were conducted to obtain the local stress intensity factor solutions for kinked cracks as functions of the kink length. The computational results indicate that the kinked cracks are under dominant mode I loading conditions and the normalized local stress intensity factor solutions can be used in combination with the global stress intensity factor solutions to estimate fatigue lives of laser welds with the weld width as small as the sheet thickness. The global stress intensity factor solutions and the local stress intensity factor solutions for vanishing and finite kinked cracks are then adopted in a fatigue crack growth model to estimate the fatigue lives of the laser welds. Also, a structural stress model based on the beam bending theory is adopted to estimate the fatigue lives of the welds. The fatigue life estimations based on the kinked fatigue crack growth model agree well with the experimental results whereas the fatigue life estimations based on the structural stress model agree with the experimental results under larger load ranges but are higher than the experimental results under smaller load ranges.     

TIG与FSW焊接工艺下2219铝合金疲劳裂纹扩展性能研究

目的 研究钨极惰性气体保护焊（TIG）和搅拌摩擦焊（FSW）对2219铝合金焊接接头疲劳性能的影响,并探究这2种不同焊接技术条件下焊接接头疲劳裂纹的产生与裂纹扩展原理,了解2种焊接接头的抗裂纹扩展能力,为工程实践应用提供数据参考。方法 采用疲劳裂纹扩展试验方法,测试上述2种焊接工艺条件下焊缝金属和热影响区组织的疲劳裂纹扩展速率da/d N和阈值,使用光学显微镜和扫描电子显微镜观察并分析金相组织和疲劳断口形貌特征。结果 疲劳裂纹倾向于沿裂纹处萌生,裂纹的存在成为主要的裂纹扩展源头,有利于加速裂纹向前延伸。热影响区由于组织结构不均匀,不同位置的晶粒尺寸存在明显差异,疲劳裂纹扩展路径倾向于沿靠近焊缝一侧向靠近母材区域扩展。TIG焊接工艺下焊缝金属和热影响区的裂纹扩展速率明显低于FSW焊接工艺下的焊缝金属和热影响区,与此同时,TIG焊接接头表现出优良的抗疲劳裂纹扩展性能。结论 通过此研究,建议2219铝合金焊接接头采用TIG焊接工艺,抗疲劳裂纹扩展效果更佳。     

Fatigue behaviour of dissimilar Al 5052 and Mg AZ31 resistance spot welds with Sn‐coated steel interlayer

The fatigue property of dissimilar spot welds between an aluminium alloy (AA5052) and a magnesium alloy (AZ31) was studied in this research. The AA5052 and AZ31 coupons were resistance spot welded together by using an interlayer of Sn‐coated steel between the two coupons. The fatigue test results revealed that the Mg/Al joints had the same level of fatigue strength as Mg/Mg resistance spot welds. It was found that within the life range of N_f < 10⁵ cycles, Mg/Al welds degraded faster than Mg/Mg joints. This was attributed to the larger bending moment on the plane of fatigue failure in the Mg/Al welds. Three failure modes were observed under different cyclic loading regimes: Al/steel interfacial failure, Mg coupon failure and Al coupon failure. Fatigue fracture surface of Mg/Al welds consisted of two distinct regions: crack propagation region with brittle morphology and final rupture with ductile morphology.     

Fatigue life assessment of improved joints welded with alternative welding techniques

In this study, the fatigue life improvement by adopting the toe weaving technique on non-load carrying cruciform welded joints has been investigated. Fatigue testing was conducted on two batches of specimens welded using double-pass manual welding. One batch had a straight second pass and the other was weaved. The influence of different weaving shape parameters was analyzed by performing crack growth analyses. The fatigue testing shows a slightly improved fatigue life for the two different batches compared to as-welded joints; the improvement is similar for both batches. The crack growth analysis concludes that the batch with the straight second pass should provide slightly higher fatigue life compared to the toe weaved batch. Measurements show a presence of undercuts in the vicinity of the crack initiation site. Nonetheless, an increased fatigue life is obtained, due to the low flank angle created during welding of the second pass, which reduces the stress concentration in the weld toe, prolonging the fatigue life.     

The Prediction of Fatigue Crack Initiation Life in Spot Welds

Abstract: In this paper, strain‐based fatigue life prediction method has been used to estimate the fatigue crack initiation life of spot‐welded joints of Mild Steel JSC270D and Ultra‐High Strength Steel JSC980Y. To do so, the joints were simulated using three‐dimensional finite‐element (FE) models, and then nonlinear FE analysis was performed to obtain the local stress and strain ranges and finally, the Morrow equation was applied to estimate the crack initiation lives. The results have been compared with those obtained from experimental crack growth morphology. In addition, the difference between fatigue limits for smooth specimens and spot‐welded joints for mentioned materials has been briefly discussed. It has been shown that mean stress values in the Ultra‐High Strength Steel can significantly decrease the fatigue limit of spot‐welded joint because even at very low load level the stresses exceed the yield point at the root of nugget of spot‐welded joint, while the amount of mean stress in the Mild Steel for the same load level is much less than that of Ultra‐High Strength Steel. The comparison between numerical results of fatigue crack initiation lives and experimental data provided good agreement between numerical predictions and crack growth morphology observations. The results also shows that in some cases, depending on the joint type, the life spent in the nucleation phase can be an important part of the final failure lifetime.     

Probabilistic fatigue crack growth analysis of spot‐welded joints

This paper presents a probabilistic fatigue crack growth life prediction methodology for spot‐welded joints under variable amplitude loading history. The loading is multi‐axial and is obtained from transient response analysis of a vehicle model using finite‐element analysis. A three‐dimensional (3D) finite element model of a simplified joint with four spot welds is developed, and the static stress analysis of this joint is performed. Then the fatigue crack inside the base material sheet is modelled as a surface crack. Probabilistic crack growth model is combined with the stress analysis result to develop a probabilistic fatigue crack growth life prediction methodology for spot welds. This new method is implemented with MSC/NASTRAN and MSC/FATIGUE and is useful for the reliability assessment of spot‐welded joints against fatigue crack growth.     

Fatigue life prediction based on crack closure for 6156 Al-alloy laser welded joints under variable amplitude loading

A fatigue prediction approach is proposed using fracture mechanics for laser beam welded Al-alloy joints under stationary variable amplitude loading. The proposed approach was based on the constant crack open stress intensity factor in each loading block for stationary variable amplitude loading. The influence of welding residual stress on fatigue life under stationary variable amplitude was taken into account by the change of crack open stress intensity factor in each loading block. The residual stress relaxation coefficient β = 0.5 was proposed to consider the residual stress relaxation for the laser beam welded Al-alloy joints during the fatigue crack growth process. Fatigue life prediction results showed that a very good agreement between experimental and estimated results was obtained.     

SUS304不锈钢点焊与胶焊接头的疲劳强度分析

通过拉剪实验测定1.5mm厚SUS304不锈钢点焊接头、胶焊接头的抗拉强度,并开展疲劳实验,获得不同应力水平下两种接头的疲劳寿命,得到两种接头的载荷-寿命曲线;借助扫描电镜分析接头疲劳失效过程。结果表明:当焊接电流为10.0kA、焊接时间为80ms、电极压力为0.5 MPa时,能获得较好的胶焊接头。在此焊接参数下,点焊接头、未固化胶焊接头和固化胶焊接头的平均失效载荷分别为12 825.5N、10 345.6N、10 022.9N;在疲劳实验载荷-寿命曲线的有限寿命区内,SUS304不锈钢胶焊接头的疲劳强度均大于点焊接头;点焊接头和胶焊接头的疲劳失效形式主要由母材眉状裂纹失效和界面撕裂失效两种形式组成;胶焊接头的疲劳失效过程中,首先是胶层粘接失效,随后疲劳裂纹从板间内表面热影响区边缘萌生,沿板厚与板宽方向扩展直至发生疲劳失效。     

A comparative study of fatigue estimation methods for single‐spot and multispot welds

Fatigue life and load data of spot‐welded samples were obtained by performing tensile‐shear fatigue tests on single‐spot‐welded samples, and by collecting published data on tensile‐shear fatigue tests of multispot‐welded samples. Finite element models of the spot‐welded samples were then constructed, and their accuracy was validated by comparing their results with those of static loading tests. Methods to estimate fatigue in spot‐welded joints proposed by Sheppard, Rupp, and Swellam were used to predict the fatigue life of each sample, and their results were compared. The sensitivity of each method to spot‐welding parameters, as well as the arrangement and number of welded spots, was analyzed to obtain their scope of applicability. Finally, the Sheppard and Rupp methods were used to obtain fitted fatigue curves of each spot‐welded sample, and the equivalent life method was used to generate P‐S‐N curves of the single‐spot‐ and multispot‐welded samples. This method can serve as a useful reference for fatigue reliability analyses of mechanical parts with spot‐welded joints.     

An experimental investigation of fatigue behavior and deformation of double spot friction welded joints

Fatigue behavior of double spot friction welded joints in aluminum alloy 7075-T6 plates is investigated by conducting monotonic tensile and fatigue tests. The spot friction welding procedures are carried out by a milling machine with a designed fixture at the best preliminary welding parameter set. The fatigue tests are performed in a constant amplitude load control servo-hydraulic fatigue testing machine with a load ratio of (R = P_min/P_max) 0.1 at room temperature. It is observed that the failure mode in cyclic loading (low-cycle and high-cycle) resembles that of the quasi-static loading conditions i.e. pure shearing. Primary fatigue crack is initiated in the vicinity of the original notch tip and then propagated along the circumference of the weld’s nugget.     

Fatigue crack propagation rates and threshold stress intensity factors for welded joints of HT80 steel at several stress ratios

Fatigue crack propagation rates and threshold stress intensity factors were measured for welded joints and base metal by using 200 mm wide centre-cracked specimens. The fatigue crack propagation properties of welded joints were similar in spite of the different zones in which the cracks propagated (ie, in the heat-affected zone and in the weld metal) and the different welding process used (submerged arc welding and gas metal arc welding). They were, however, inferior to those of the base metal. It was revealed by observation of the crack closure that the fatigue cracks were fully open during the whole range of loading, due to the tensile residual stress distribution in the middle part of the welded joints. This observation also explains the lack of a stress ratio effect on the fatigue crack propagation properties of welded joints, and their inferiority to those of the base metal.     

Analysis of fatigue crack behaviour based on dynamic response simulations and experiments for tensile-shear spot-welded joints

Fatigue crack initiation and propagation behaviours were studied based on the dynamic response simulation by the three‐dimensional finite‐element analysis (FEA) and dynamic response experiments for tensile‐shear spot‐welded joints. The entire fatigue propagation behaviour from the surface elliptical cracks at the initiation stage to the through thickness cracks at the final stage was taken into consideration during the three‐dimensional FEA dynamic response simulations. The results of the simulations and experiments found that the fatigue cracks of spot‐welded joint from initial detectable crack sizes to crack propagation behaviour could be described by three stages. Approximately one‐half of the total fatigue life was taken in stage I, which includes micro‐crack nucleation and the small crack growth process; 20% of the total fatigue life in stage II, in which the existing surface crack propagates through the thickness of sheet and 30% of the total fatigue life in stage III, during which the through thickness crack propagates along the direction of plate width to the final failure. According to the relationship between the crack length and depth and the dynamic response frequency during the simulated fatigue damage process, the definition of fatigue crack initiation and propagation stages was proposed. The analysis will provide some information for the fatigue life prediction of the spot‐welded structures.     

Failure mode and fatigue behavior of weld-bonded lap-shear specimens of magnesium and steel sheets

Failure modes and fatigue behaviors of ultrasonic spot welds in lap-shear specimens of magnesium AZ31B-H24 and hot-dipped-galvanized mild steel sheets with and without adhesive were investigated. The spot welded specimens failed from the kinked crack growth mode. The adhesive-bonded specimens failed from the cohesive failure through the adhesive and the kinked crack growth through the magnesium sheet. The weld-bonded specimens failed from the cohesive failure through the adhesive, the interfacial failure through the spot weld, and the kinked crack growth through the magnesium sheet. The estimated fatigue lives for the adhesive-bonded and weld-bonded specimens failed from the kinked crack growth mode are lower than the experimental results.     

Establishing criteria for root and toe cracking of load carrying cruciform joints of pressure vessel grade steel

In this investigation an attempt has been made to establish a criterion to forecast the possible crack initiation region (toe or root) in double fillet welded load carrying cruciform joints and also to know the probable failure mode. Cruciform joints were fabricated from pressure vessel grade (ASTM 517 ‘F’ grade) steel using shielded metal arc welding (SMAW) and flux cored arc welding (FCAW) processes. Fatigue crack growth experiments were carried out in a mechanical resonance vertical pulsator (SCHENCK 200 kN capacity) with a frequency of 30 Hz under constant amplitude loading (R=0). It was found that the fatigue crack initiation lives (root crack or toe crack) were relatively lower in the joints fabricated by FCAW process than the joints fabricated by SMAW process.     

A comprehensive investigation on the effects of laser and shot peening on fatigue crack growth in friction stir welded AA 2195 joints

The effects of various surface treatment techniques on the fatigue crack growth performance of friction stir welded 2195 aluminum alloy were investigated. The objective was to reduce fatigue crack growth rates and enhance the fatigue life of welded joints. The crack growth rates were assessed and characterized for different peening conditions at a stress ratio (R) of 0.1, and 0.7. The surface and through-thickness residual stress distribution were also investigated and presented for the various regions in the weld. Tensile residual stresses introduced during the welding process were found to become significantly compressive, particularly after laser peening. The effect of the compressive stresses was deemed responsible for increasing the resistance to fatigue crack growth of the welds. The results indicate a significant reduction in fatigue crack growth rates using laser peening compared to shot peening and native welded specimens. This reduced fatigue crack growth rate was comparable to the base unwelded material.     

Comparison of fatigue properties between friction stir welds and TIG welds

对比分析了搅拌摩擦和氩弧焊两种工艺方法对铝合金焊接接头疲劳性能的影响,建立了焊接接头的S-N曲线,结果表明：在相同的载荷条件下,搅拌磨擦焊接接头的疲劳性能优于氩弧焊接头。搅拌摩擦焊接头疲劳寿命N=106次的疲劳强度值约为59~65MPa之间。对焊接接头显微组织的分析表明：搅拌摩擦焊接接头具有比氩弧焊接头更为细小的晶粒和狭窄的焊接热影响区,阻碍了滑移带的形成和裂纹的扩展,从而提高了接头的疲劳性能。TIG焊接接头疲劳端口分析显示,焊接缺陷是主要的疲劳裂纹源。     

Fatigue Life Behaviour of Spot Friction Welded Al 5083‐O in Single Cover Butt Joints

In this study, the fatigue behaviour of spot friction welded joints of Al 5083‐O was investigated using experimental and numerical approaches. In the experimental part, a single cover butt joint of aluminium sheets with a thickness of 2 mm was fatigue tested under constant amplitude cyclic loadings. The sheets were connected using a spot friction welding technique with constant welding parameters of tool rotational speed, holding time, travelling speed, and shoulder plunge depth. Fatigue cracks were initiated in the vicinity of the weld notch and then propagated along the circumference of the weld's nugget. In the numerical part, a three‐dimensional finite element model was developed to determine stress and strain distributions in the spot friction welded joint and to predict the fatigue life using three approaches of Morrow, modified Morrow, and Smith–Watson–Topper. The results showed a good agreement between the fatigue life predictions and experimental data.     

Fatigue reliability analysis of kiln welded shell

This paper presents a probabilistic reliability method for the welded shell during crack growth. The crack growth model incorporated with a failure assessment diagram, which provides a better estimation of the critical crack depth, is developed to describe fatigue failure. All variables used of particular welded joints are studied. The stress variables are based on resultant stress calculated by using the finite element (FE) code ANSYS. Fatigue reliability analysis of the welded shell is performed by using the Monte Carlo simulation method. It is demonstrated that fatigue reliability analysis is significantly useful for the repair schedule of shell cracks.     

Effect of Notch Location on Fatigue Life Prediction of Strength Mismatched HSLA Steel Weldments

Welding of high strength low alloy steels (HSLA) involves usage of low, even and high strength filler materials (electrodes) than the parent material depending on the application of the welded structures and the availability of the filler material. In the present investigation, the fatigue crack growth behaviour of weld metal (WM) and heat affected zone (HAZ) regions of under matched (UM), equal matched (EM) and over matched (OM) joints has been studied. The base material used in this investigation is HSLA-80 steel of weldable grade. Shielded metal arc welding (SMAW) process has been used to fabricate the butt joints. Centre cracked tension (CCT) specimen has been used to evaluate the fatigue crack growth behaviour of the welded joints. Fatigue crack growth experiments have been conducted using servo hydraulic controlled fatigue testing machine at constant amplitude loading (R=0). A method has been proposed to predict the fatigue life of HSLA steel welds using fracture mechanics approach by incorporatin