Improvement of mechanical properties of stainless maraging steel laser weldments by post-weld ageing treatments

The response of stainless maraging steel weldments to post-weld ageing treatment has been investigated. Post-weld ageing was performed at five different temperatures, viz., 420 °C, 460 °C, 500 °C, 540 °C, and 580 °C. Metallographic characterization of weldment revealed three zones, namely fusion zone, heat-affected zone (HAZ) and unaffected parent metal zone. Hardness and tensile properties were evaluated after ageing at different temperatures. Hardness in HAZ and fusion zone varied with ageing temperature differently from that of the parent metal; it became higher in HAZ and fusion zone than in parent metal zone above 420 °C. Among the applied ageing treatments, ageing at 460 °C achieved the highest tensile strength. A graph was constructed for determination of fracture location and post-weld heat treatment efficiency based on experimental results, using hardness ratio of HAZ to the treated parent material and hardness ratio of HAZ to the as-received parent material.     

Effect of heat treatment on the tribological properties of Al–Cu–Mg/nanoSiC composites

In this study, the effect of heat treatment on the tribological properties of Al–Cu–Mg alloy reinforced with 4 wt.% SiC particles with 650 nm average particle size has been investigated. The age hardening process consists of solution treatment at 540 °C for 6 h, followed by water quenching and ageing at different temperatures of 175, 200 and 225 °C with soaking times of 3, 6 and 9 h. Hardness measurements were applied to monitor the precipitation effect and the aged samples were then subjected to wear tests under dry sliding conditions against steel and alumina counterfaces. The results showed that the reinforced material exhibits an enhanced ageing response compared to the unreinforced material in the same heat treatment conditions. The rate of ageing increases with increasing temperature; however, ageing at 200 and 225 °C for more than 6 h resulted in over-ageing. The best combinations for the enhanced tribological properties for the composite material were selected as 6 h ageing at 225 °C. The precipitation effect for this alloy can be enhanced by the small addition of SiC nanoparticles. Having a small amount of nanoSiC particles with fine precipitates inside the matrix further increases the hardness and wear properties.     

Effect of porosity and density on the mechanical and microstructural properties of sintered 316L stainless steel implant materials

In this study, the microstructure and mechanical properties of sintered AISI 316L stainless steel implant materials produced by powder metallurgy (P/M) method were investigated as a function of porosity amount. AISI 316L stainless steel powders were cold-pressed with 800 MPa pressure and sintered at 1200 °C, 1250 °C and 1300 °C for 30 min in a nitrogen atmosphere. The mechanical properties of the 316L implant samples were determined by tensile, fatigue and microhardness tests. Metallographic studies such as pore formation, and fractured surface analyses were performed by Scanning Electron Microscopy (SEM) and Light Optical Microscopy (LOM). The results of this study indicate that, irregular pore formation tendencies increase with an increase in porosity (%). Furthermore, an increase in porosity was shown to decrease the mechanical properties of sintered AISI 316L stainless steel. Sintering temperature is important parameter in decreasing the porosity of P/M materials.     

Dependence of dynamic strain ageing on strain amplitudes during the low-cycle fatigue of TP347H austenitic stainless steel at 550 °C

Low-cycle fatigue (LCF) tests are carried out on TP347H stainless steel at a strain rate of 8 × 10⁻³ s⁻¹ with total strain amplitudes (Δε_t/2) of ±0.4% and ±1.0%, at room temperature (RT) and 550 °C. It is found that the stress responses and dislocation structures under cyclic loading strongly depend on the value of strain amplitude at 550 °C. Compared with those at the same strain amplitude at RT, the material shows a rapid strain softening, and finally attains a stabilized state at Δε_t/2 = ±0.4% and 550 °C, but the one presents an anomalous behavior, i.e., first a rapid hardening to the maximum stress, followed by a reducing softening at Δε_t/2 = ±1.0% and 550 °C. More cells resulting from dislocation cross-slip and planar structures due to dynamic strain ageing (DSA) restricting cross-slip develop at low strain amplitude of ±0.4% at the first cycle. However, there are more complicated dislocation structures, such as cells, elongated cells, walls/channels and planar structures at Δε_t/2 = ±1.0%. The observations of scanning electron microscopy (SEM) and transmission electron microscopy (TEM) exclude the effects of martensitic transformation, creep, oxidation, and precipitations on these stress responses and microstructure evolutions, which result from DSA appearing at 550 °C.     

Novel Cu-bearing economical 21Cr duplex stainless steels

A new family of 21Cr–2 Ni–1.0Mo–0.2 N–xCu (x = 0.5, 1.0, 1.5) economical duplex stainless steels have been developed by examining the effect of Cu on the microstructure and properties of solution-treated specimens. The results have shown that these alloys have a balanced ferrite–austenite duplex structure. The ferrite content increases with the solution treatment temperature, but decreases with an increase in Cu. Some precipitates such as sigma phase, ε-Cu and Cr₂N were found when solution-treated at 780 °C for 30 min. The yield strength, tensile strength and fracture elongation values of experimental alloys solution-treated at 1020 °C for 30 min were about 540 MPa, 1000 MPa, and 35%, respectively. The pitting corrosion potentials of the solution-treated alloys were all above 500 mV in 1 mol/L NaCl solution at room temperature and the pitting corrosions always occur in ferrite phase. The mechanical properties and corrosion resistance of the designed alloys with lower production cost are better than those of AISI 316L austenitic stainless steel.     

Elevated temperature low cycle fatigue of grey cast iron used for automotive brake discs

This paper evaluates the fatigue life properties of low carbon grey cast iron (EN-GJL-250), which is widely used for automotive brake discs. Although several authors have examined mechanical and fatigue properties at room temperatures, there has been a lack of such data regarding brake discs operating temperatures. The tension, compression and low cycle fatigue properties were examined at room temperature (RT) and at brake discs’ working temperatures: 500 °C, 600 °C and 700 °C. The microstructure of the material was documented and analysed. Tensile stress–strain curves, cyclic hardening/softening curves, stress–strain hysteresis loops, and fatigue life curves were obtained for all the above-mentioned temperatures. It was concluded, that Young’s modulus is comparable with both tension and compression, but yield its strength and ultimate strength are approximately twice as great in compression than in tension. All the mechanical properties remained quite stable until 500 °C, where at 700 °C all deteriorated drastically. During fatigue testing, the samples endured at 500 °C on average at around 50% of cycles at room temperature. Similar to other materials’ properties, the cycles to failure have dropped significantly at 700 °C.     

Effects of microstructure changes on the superplasticity of 2205 duplex stainless steel

The high temperature deformation behavior of 2205 duplex stainless steel under different conditions had been studied by tensile tests. The whole tensile test was conducted at a constant temperature 950 °C with an initial strain rate 1.5 × 10⁻³/s. Some tests were interrupted purposely and then the samples were quenched using water. Elongations of the fractured specimens were calculated. Microstructure changes just before and during the deformation were observed. Phase ratio of σ precipitate was analyzed. The results showed that the superplasticity of 2205 duplex stainless steel was directly affected by the microstructure before the deformation. The recrystallization phenomenon was distinct along with the homogenizing time and the grains became equiaxed and stable. Meanwhile, the quantity of σ phase increased when prolonged the homogenizing time. After homogenized for 7 min before the tensile test, the σ phase ratio was about 4.8% and the grain size was about 998 nm, the maximum elongation value 1260% was obtained. During the deformation progress, dynamic recrystallization was observed and quantity of σ phase increased with the increasing of deformation strain. The σ phase restricted the grain growth and kept the equiaxed duplex structure stable with a grain size of about 1 μm.     

Effect of post weld heat treatment on the microstructure and mechanical properties of ITER-grade 316LN austenitic stainless steel weldments

The effect of postweld heat treatment (PWHT) on the microstructure and mechanical properties of ITER-grade 316LN austenitic stainless steel joints with ER316LMn filler material was investigated. PWHT aging was performed for 1 h at four different temperatures of 600 °C, 760 °C, 870 °C and 920 °C, respectively. The microstructure revealed the sigma phase precipitation occurred in the weld metals heat-treated at the temperature of 870 °C and 920 °C. The PWHT temperatures have the less effect on the tensile strength, and the maximum tensile strength of the joints is about 630 MPa, reaching the 95% of the base metal, whereas the elongation is enhanced with the rise of PWHT temperatures. Meanwhile, the sigma phase precipitation in the weld metals reduces the impact toughness.     

Processing of a new high strength high toughness steel with duplex microstructure (Ferrite + Austenite)

In this investigation a new third generation advanced high strength steel (AHSS) has been developed. This steel was synthesized by austempering of a low carbon and low alloy steel with high silicon content. The influence of austempering temperature on the microstructure and the mechanical properties including the fracture toughness of this steel was also examined. Compact tension and cylindrical tensile specimens were prepared from a low carbon low alloy steel and were initially austenitized at 927 °C for 2 h and then austempered in the temperature range between 371 °C and 399 °C to produce different microstructures. The microstructures were characterized by X-ray diffraction, scanning electron microscopy and optical metallography. Test results show that the austempering heat treatment has resulted in a microstructure consisting of very fine scale bainitic ferrite and austenite. A combination of very high tensile strength of 1388 MPa and fracture toughness of 105 MPa √m was obtained after austempering at 371 °C.     

Investigation on the solution treated behavior of economical 19Cr duplex stainless steels by Mn addition

Effect of Mn on microstructure, mechanical property and pitting corrosion of 19% Cr economical duplex stainless steels with solution temperatures ranging from 1040 to1220 °C has been investigated. The austenite content increases with more Mn addition, but decreases by increasing solution temperature, which can be inferred by trend of partition coefficient K_Mn with solution temperature. Meanwhile, a balanced austenite-ferrite duplex structure of solution-treated specimens was obtained with Mn addition. The impact energy at 20 °C increased with decreasing solution temperature from 1220 °C to 1040 and 1120 °C, and improved by more Mn addition due to more ductile austenite phase formation. These toughness variations were consistent with fracture morphology characteristic changing. The effect of more Mn addition and solution treatment of 1120°Con decreasing of tensile strength and 0.2% offset yield strength were slight. However, the elongation to fracture (%) fell greatly with Mn addition up to 8.1 wt.% for as-rolled and solution treated specimens due to larger deformation strains of austenite than that of ferrite. The decreasing trend of pitting corrosion potential became slower with Mn addition from 3.6 to 8.1 wt.%. The pitting corrosion resistance was lowered by increasing solution temperature due to more weakened repassivation ferrite phase formation.     

Hot workability of 00Cr13Ni5Mo2 supermartensitic stainless steel

The hot workability of 00Cr13Ni5Mo2 supermartensitic stainless steel was investigated by hot compression and hot tension tests conducted over the temperature range of 950–1200 °C and strain rates varying between 0.1 and 50 s^?1. The processing map technique was applied on the basis of dynamic materials model and Prasad instability criterion. Microstructure evolutions, Zener–Hollomon parameter as well as hot tensile ductility were examined. The results show that, as for the hot working of 00Cr13Ni5Mo2 supermartensitic stainless steel in the industrial production, the large strain deformation should be carried out in the temperature range 1140–1200 °C and strain rate range 0.1–50 s^?1, where the corresponding Zener–Hollomon parameters exhibit low values. Moreover, when deformed under high strain rate range (above 15 s^?1), the deformation temperature can be reduced reasonably.     

Microstructure and mechanical properties of 12 wt.% Cr ferritic stainless steel with Ti and Nb dual stabilization

TCS stainless steel is a 12 wt.% Cr ferritic stainless steel with 0.040 wt.% Ti and 0.096 wt.% Nb dual stabilization. This paper investigated the microstructures and mechanical properties of TCS stainless steel heated at 600–1300 °C for 10 min and followed water quenching. Results show the increasing of both tensile strength and hardness meanwhile the ductility and toughness have experienced the decreasing due to formation of martensitic phase and grain coarsening. In the unheated and heated TCS stainless steel, there are mainly two kinds of particles: Ti-rich particles in size of 2–5 μm; Nb-rich particles in size of 20–50 nm.     

Effects of inter-critical temperatures on martensite morphology,volume fraction and mechanical properties of dual-phase steels obtained from direct and continuous annealing cycles

Homogenizing and normalizing heat treatments were performed on low carbon–manganese steel. Then, direct and continuous annealing heat treatments were carried out at 800 °C, 770 °C, 750 °C and 725 °C. Finally; dual phase ferrite–martensite steel was obtained. Thereafter, hardness and tensile tests were applied at ambient temperature, and impact tests for the initial sample and the dual-phase steels obtained from continuous and direct annealing heat treatment in the temperature ranges of (−67 to +70), (−70 to +60), (−70 to +29), respectively, were accomplished. The ductile–brittle transition temperature (DBTT) and the fracture modes of the samples were obtained, and the fracture surface of the steel was observed through scanning electron microscopy (SEM). The results revealed that the best mechanical properties in dual-phase steels, like impact toughness and flexibility, appear at the inter-critical temperature of 725 °C for both continuous and direct annealing cycles. The (DBTT) for the specimens obtained from direct and continuous annealing and the initial sample were −49 °C, −6 °C, and −34 °C, respectively. The dual-phase specimen achieved through the direct annealing method had better toughness and impact properties than the initial specimen or the one obtained through continuous annealing.     

Effect of aging on the corrosion resistance of 2101 lean duplex stainless steel

The microstructure and localized corrosion behavior of a 2101 lean duplex stainless steel aged at 700 °C were investigated. The results showed that changes in the microstructure of the duplex stainless steel, due to the formation of precipitates, affected its pitting corrosion resistance. The values of the pitting potential and the critical pitting temperature dropped drastically before aging time up to 30 min. The potentiostatic pitting corrosion measurement indicated more sensitive to the small amount of precipitates compared to the potentiodynamic test. Pitting nucleated mainly in the ferrite phase for the solution-annealed specimen, while the initiation of pitting corrosion for the aged specimen took place at Cr-depletion area around the precipitates, i.e. in the newly formed secondary austenite phase.     

Study of decomposition of ferrite in a duplex stainless steel cold worked and aged at 450–500 °C

The influence of cold-deformation on ferrite decomposition in duplex stainless steel during heat treatment at 450–500 °C was investigated using micro-hardness measurements and transmission electron microscopy. It was found that cold-deformation can change the mechanism of the α → α + α′ phase separation in the ferrite from nucleation and growth to spinodal decomposition. This finding is discussed in terms of the influence of an increased dislocation density on coherency strains.     

Design of a new Ni-free austenitic stainless steel with unique ultrahigh strength-high ductility synergy

A conceptual approach was used to design a new Ni-free austenitic stainless steel with a unique combination of ultrahigh strength and ductility. The concept was based on the alloying of the 0.05C–18Cr–12Mn (wt.%) steel by 0.39%N and heavy warm rolling (84% reduction) at 1173 K (900 °C) to achieve the yield strength of minimum 1 GPa and high tensile strength and elongation due to a proper stability of the austenite as a result of the optimized stacking fault energy (SFE). The yield strength of 1010 MPa, tensile strength of 1150 MPa and high fracture strain of 70% were measured for the steel designed. Dislocation and solid solution hardening mechanisms are introduced as the main contributors for the ultrahigh yield strength of the steel. The strain hardening is gradual and the hardening rate reaches a high level of ∼2400 MPa at a high true strain of 40% due to slow α′-martensitic transformation and mechanical twinning. Consequently, the ductility of the designed steel is excellent.     

Mechanical properties of normal strength mild steel and high strength steel S690 in low temperature relevant to Arctic environment

The development of Arctic oil and gas fields requires low temperature high strength steel materials that can resist critical loads in extreme environments. This paper investigates the mechanical properties such as stress–strain curves, elastic modulus, yield strength, ultimate tensile strength, and fracture strain of normal mild steel and high strength S690 steel to be used in low temperatures relevant to arctic environment. Tensile tests are carried out on steel coupons at different temperatures ranging from −80 °C to +30 °C in a cooling chamber. The influences of the low temperatures on the mechanical properties of mild steel and high strength steel are compared and their differences are discussed. Regression analyses are also carried out on the test data to develop empirical formulae to predict the elastic modulus, yield strength, and ultimate strength of the steels at ambient low temperatures. Finally, design formulae are recommended and their accuracies are further confirmed by the test data including those from the literature.     

Heat treatment effect on thermo-mechanical fatigue and low cycle fatigue behaviors of A356.0 aluminum alloy

In the present paper, the heat treatment effect on A356.0, a cast aluminum alloy which has been widely used in diesel engine cylinder heads, is investigated under out-of-phase thermo-mechanical fatigue and low cycle fatigue (at different temperatures) loadings. A typical heat treatment is applied to the material including 8 h solution at 535 °C, water quench and 3 h ageing at 180 °C. The experimental fatigue results show that the heat treatment process has considerable influence on mechanical and low cycle fatigue behaviors, especially at room temperature, but its effect on thermo-mechanical fatigue lifetime is not significant. The improvement in the strength can be explained by the dislocation theory. Under thermo-mechanical fatigue loadings, the difference between the fatigue lifetime of A356.0 alloy and A356.0-T6 alloy decreases when the temperature range increases. In this condition, plastic strain increases severely during the fatigue cycles in A356.0-T6 alloy due to over-ageing phenomenon and therefore, the amount of cyclic softening in heat treated alloy is more.     

Film condensation heat transfer characteristics of R134a on horizontal stainless steel integral-fin tubes at low heat transfer rate

Condensation heat transfer characteristics of R134a on the integral-fin tubes are experimentally investigated. The test tubes are made of stainless steel, and the root diameter of the tubes is 13.27 mm. The height of fin is 1.19 mm, and the densities of the integral fin are 19 fpi and 26 fpi. The present tests were conducted at the saturation temperatures of 20 °C and 30 °C. The condensation heat transfer coefficients of the tubes having 19 fpi and 26 fpi at the saturation temperature of 20 °C are higher than that of the plain tube by 4.4 and 3.1 times, respectively. When the temperature difference across the condensate film is less than 0.7 °C, the enhancement of the tube of 19 fpi is much larger than that of the tube of 26 fpi. The Honda and Nozu model shows the smallest mean deviation between the estimated values and experimental results among the existing models.     

Effect of heat treatment and Fe content on the microstructure and mechanical properties of die-cast Al–Si–Cu alloys

The effect of solution and ageing heat treatment on the microstructure and mechanical properties of the die-cast Al–9 wt.%Si–3.5 wt.%Cu alloys containing 0.1–1.0 wt.% Fe was investigated. The results showed that the dendritic primary α-Al phase was varied from 20 to 100 μm in size and the globular α-Al grains were smaller than 10 μm in size. The Fe-rich intermetallics exhibited coarse compact or star-like shapes with the sizes from 10 to 20 μm and the fine compact particles at an average size of 0.75 μm. The solution treatment of the alloys could be achieved in a short period of time, typically 30 min at 510 °C, which dissolved the Cu-rich intermetallics into the primary α-Al phase and spheroidised the eutectic Si phase. During the subsequent ageing treatment, numerous fine precipitates of θ′ and Q′ phases were formed to provide effective strengthening to the α-Al phase, significantly improving the mechanical properties. Therefore, Fe content in the die-cast Al–Si–Cu alloys needs to be controlled at a low level in order to obtain the improved ductility and strength under solution and aged condition.