Compatible and crystallization properties of poly(lactic acid)/poly(butylene adipate‐co‐terephthalate) blends

Differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD) and dynamic mechanical analysis (DMA) properties of poly(lactic acid)/ poly(butylene adipate‐co‐terephthalate) (PLA/PBAT) specimens suggest that only small amounts of poor PLA and/or PBAT crystals are present in their corresponding melt crystallized specimens. In fact, the percentage crystallinity, peak melting temperature and onset re‐crystallization temperature values of PLA/PBAT specimens reduce gradually as their PBAT contents increase. However, the glass transition temperatures of PLA molecules found by DSC and DMA analysis reduce to the minimum value as the PBAT contents of PLA_xPBAT_y specimens reach 2.5 wt %. Further morphological and DMA analysis of PLA/PBAT specimens reveal that PBAT molecules are miscible with PLA molecules at PBAT contents equal to or less than 2.5 wt %, since no distinguished phase‐separated PBAT droplets and tan δ transitions were found on fracture surfaces and tan δ curves of PLA/PBAT specimens, respectively. In contrast to PLA, the PBAT specimen exhibits highly deformable properties. After blending proper amounts of PBAT in PLA, the inherent brittle deformation behavior of PLA was successfully improved. Possible reasons accounting for these interesting crystallization, compatible and tensile properties of PLA/PBAT specimens are proposed. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Miscibility and crystallization of biodegradable poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate)/poly(vinyl phenol) blends

Miscibility and crystallization of biodegradable poly (3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) (PHBHHx)/poly(vinyl phenol) (PVPh) blends were investigated in this work. PHBHHx is miscible with PVPh over the whole composition range as evidenced by the single composition dependent glass transition temperature and the depression of equilibrium melting point of PHBHHx in the blends. The overall crystallization rates decrease with increasing crystallization temperature for both neat PHBHHx and its blends with PVPh; moreover, the overall crystallization rates are slower in the PHBHHx/PVPh blends than in neat PHBHHx at the same crystallization temperature. Blending with PVPh may change the crystallization mechanism of PHBHHx in the blends compared with that of neat PHBHHx. Both neat PHBHHx and the PHBHHx/PVPh blends exhibit a crystallization regime II to III transition. The crystal structure of PHBHHx is not modified in the PHBHHx/PVPh blends; however, the values of crystal layer thickness, amorphous layer thickness, and long period all become larger with increasing PVPh content in the blends. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

Influence of phthalic anhydride and bioxazoline on the mechanical and morphological properties of biodegradable poly(lactic acid)/poly[(butylene adipate)‐co‐terephthalate] blends

Poly(lactic acid) (PLA)/poly[(butylene adipate)‐co‐terephthalate] (PBAT) blends were fabricated by melt blending, with 2,2′‐(1,3‐phenylene)bis(2‐oxazoline) (BOZ) and phthalic anhydride (PA) used as compatibilizers. It was found that a small amount of BOZ or PA greatly increased the elongation at break of the PLA/PBAT blends without sacrificing their high tensile strength. Scanning electron microscopy results revealed that the PBAT particles became finer and were uniformly dispersed in the matrix when the compatibilizers were incorporated, which indicated that the interfacial bonding and compatibilization between PLA and PBAT were improved in the presence of the compatibilizers. Compared with PLA/PBAT blends, the molecular weight of PLA/PBAT/PA/BOZ blends was increased due to chain‐extending reactions. Differential scanning calorimetry results suggested PBAT decreased the crystallization rate and crystallinity of PLA in the blends. Moreover, the glass transition temperature of PBAT was further decreased when the compatibilizers were used. © 2013 Society of Chemical Industry     

Kinetics and crystal structure of isothermal crystallization of poly(lactic acid) plasticized with triphenyl phosphate

In this article, the spherulitic growth rate of neat and plasticized poly(lactic acid) (PLA) with triphenyl phosphate (TPP) was measured and analyzed in the temperature range of 104–142°C by polarizing optical microscopy. Neat PLA had the maximum value of 0.28 μm/s at 132°C, whereas plasticized PLA had higher value than that of neat PLA, but the temperature corresponding to the maximum value was shifted toward lower one with increasing TPP content. The isothermal crystallization kinetics of neat and plasticized PLA was also analyzed by differential scanning calorimetry and described by the Avrami equation. The results showed for neat PLA and its blends with various TPP contents, the average value of Avrami exponents n were close to around 2.5 at two crystallization temperatures of 113 and 128°C, the crystallization rate constant k was decreased, and the half‐life crystallization time t_1/2 was increased with TPP content. For neat PLA and its blend with 15 wt % TPP content, the average value of n was 2.0 and 2.3, respectively, the value of k was decreased, and the value of t_1/2 was increased with crystallization temperature (T_c). Further investigation into crystallization activation energy ΔE_a of neat PLA and its blend with 15 wt % TPP showed that ΔE_a of plasticized PLA was increased compared to neat PLA. It was verified by wide‐angle X‐ray diffraction that neat PLA and its blends containing various TPP contents crystallized isothermally in the temperature range of 113–128°C all form the α‐form crystal. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Miscibility and crystallization behaviors of biodegradable poly(butylene succinate‐co‐butylene terephthalate)/phenoxy blends

Miscibility and crystallization behaviors of biodegradable poly(butylene succinate‐co‐butylene terephthalate) (PBST)/poly(hydroxyl ether biphenyl A) (phenoxy) blends were investigated with various techniques in this work. PBST and phenoxy are completely miscible as evidenced by the single composition‐dependent glass transition temperature over the entire blend compositions. Nonisothermal melt crystallization peak temperature is higher in neat PBST than in the blends at a given cooling rate. Isothermal melt crystallization kinetics of neat and blended PBST was studied and analyzed by the Avrami equation. The overall crystallization rate of PBST decreases with increasing crystallization temperature and the phenoxy content in the PBST/phenoxy blends; however, the crystallization mechanism of PBST does not change. Moreover, blending with phenoxy does not modify the crystal structure but reduces the crystallinity degree of PBST in the PBST/phenoxy blends. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Mechanical properties and morphological changes of poly(lactic acid)/polycarbonate/poly(butylene adipate‐co‐terephthalate) blend through reactive processing

The mechanical properties and morphological changes of poly(lactic acid) (PLA), polycarbonate (PC), and poly(butylene adipate‐co‐terephthalate) (PBAT) polymer blends were investigated. Several types of blend samples were prepared by reactive processing (RP) with a twin‐screw extruder using dicumyl peroxide (DCP) as a radical initiator. Dynamic mechanical analyses (DMA) of binary polymer blends of PC/PBAT indicated that each component was miscible over a wide range of PC/PBAT mixing ratios. DMA of PLA/PBAT/PC ternary blends revealed that PBAT is miscible with PC even in the case of ternary blend system and the miscibility of PLA and PBAT can also be modified through RP. As a result, the tensile strain and impact strength of the ternary blends was increased considerably through RP, especially for PLA/PBAT/PC = 42/18/40 (wt/wt/wt) with DCP (0.3 phr). Scanning electron microscopy (SEM) analysis of the PLA/PBAT/PC blends revealed many small spherical island phases with a domain size of approximately 0.05–1 μm for RP, whereas it was approximately 10 μm without RP. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Mechanical and morphological properties of poly(butylene adipate‐co‐terephthalate) and poly(lactic acid) blended with organically modified silicate layers

Poly(butylene adipate‐co‐terephthalate) (PBAT) is a biodegradable polymer with high ultimate elongation but low modulus. This work studied the addition of a rigid bio‐based and biodegradable polymer, poly(lactic acid) (PLA), along with organically modified silicate layers as a conceivable means to improve the modulus of PBAT. Blending with PLA would also reduce both the cost of the ultimate blend and its dependence on nonrenewable resources. Compounds of PBAT with PLA and organically modified silicate layers showed significantly improved tensile and flexural strength resulting in enhanced thermomechanical performances compared to neat PBAT. The state of clay dispersion was evaluated using common analytical techniques such as transmission electron microscopy, X‐ray diffraction, and rheometry. The clay platelets were partially dispersed in a PBAT and PLA phase and a large portion of the platelets were located at the interface. The incorporation of organoclay reduced the dispersed phase domain (i.e., PLA) size significantly. The smaller PLA size however, did not translate into better elongational properties. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Formulation and characterization of compatibilized poly(lactic acid)‐based blends and their nanocomposites with silver‐loaded kaolinite

Biodegradable polymer nanocomposites have been developed in this study as materials for use in the packaging of moisture‐sensitive products. Poly(lactic acid) (PLA) was the main component of the nanocomposites with poly(butylene adipate‐co‐terephthalate) (PBAT) as flexibility enhancer. Tetrabutyl titanate was also added as a compatibilizer to enhance the interfacial affinity between PLA and PBAT by inducing the formation of some PLA/PBAT via transesterification during the melt blending process, thereby improving the mechanical properties of the blends. Silver‐loaded kaolinite synthesized via chemical reduction was also incorporated into the compatibilized blends for further property improvement. Herein, we report a novel biodegradable quaternary nanocomposite system with intercalated‐exfoliated clay dispersion that was uniquely achieved by increasing the interlamellar space between kaolinite layers through silver nanoparticle insertion. The resultant nanocomposites containing as little as 4 phr modified clay reduced the elongation at break from 213.0 ± 5.85% to 53.8 ± 1.81%, enhanced thermal stability (initial decomposition temperature increased from 378 °C to 399 °C) and exhibited a water vapor permeability reduction of 41.85%. On the basis of these properties, the developed nanocomposites are considered to be promising candidates for use in bio‐packaging applications to replace non‐biodegradable and petro‐based plastics. © 2014 Society of Chemical Industry     

Facile fabrication of highly flexible poly(lactic acid) film using alternate multilayers of poly[(butylene adipate)‐co‐terephthalate]

Poly(lactic acid) (PLA) and poly[(butylene adipate)‐co‐terephthalate] (PBAT) are both commonly used biodegradable polymers. In this study, co‐extrusion of PLA and PBAT was used to create alternately multilayered films in order to obtain high‐flexibility PLA film. The incorporation of PBAT provides enhanced flexibility to PLA and the effect is more distinct in the PLA/PBAT multilayer film as the number of layers increases. Through differential scanning calorimetric and wide‐angle X‐ray scattering analyses, the crystallinity of PLA is shown to decrease more in the multilayer film than in the blended film. Transparency is also enhanced in the multilayer film. The fabrication of alternate multilayered film by co‐extrusion of PLA and PBAT shows a new method of preparing a flexible, transparent and fully biodegradable film, which is impossible through a blending process. © 2014 Society of Chemical Industry     

Effect of plasticizer on the crystallization behavior of poly(lactic acid)

In this article, the spherulitic morphology and growth rate of the neat and plasticized poly(lactic acid) (PLA) with triphenyl phosphate (TPP) were compared and analyzed by polarizing optical microscopy with hot stage at a temperature range of 100?142°C. The spherulitic morphology of the neat PLA underwent a series of changes such as the typical Maltese Cross at less than 132°C, the disappearance of the Maltese Cross at 133°C, the irregular and distorted spherulites at higher than 134 and 142°C, respectively. For plasticized PLA, the spherulitic morphology exhibited the same changes as neat PLA, but these changes were shifted to lower temperature when compared with neat PLA. In the case of the spherulitic growth, neat PLA had the maximum value of 0.28 μm/s at 132°C, and plasticized PLA had higher values than that of neat PLA. Further analysis based on the Lauritzen–Hoffman theory was presented and results showed that the values of nucleation parameter K_g increased with TPP content. The crystallization behavior of PLA was analyzed by differential scanning calorimetry and wide‐angle X‐ray diffraction. The results showed that the degree of crystallinity of plasticized PLA markedly increased when compared with neat PLA sharply with the incorporation of plasticizer. The crystallization kinetics for the neat and plasticized PLA under isothermal crystallization at 114°C was described by the Avrami equation and the Avrami exponent is close to 2, implying that the crystallization mechanism did not change. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Thermal properties and non‐isothermal crystallization behavior of poly(trimethylene terephthalate)/poly(lactic acid) blends

Thermal properties and non‐isothermal melt‐crystallization behavior of poly(trimethylene terephthalate) (PTT)/poly(lactic acid) (PLA) blends were investigated using differential scanning calorimetry and thermogravimetric analysis. The blends exhibit single and composition‐dependent glass transition temperature, cold crystallization temperature (T_cc) and melt crystallization peak temperature (T_mc) over the entire composition range, implying miscibility between the PLA and PTT components. The T_cc values of PTT/PLA blends increase, while the T_mc values decrease with increasing PLA content, suggesting that the cold crystallization and melt crystallization of PTT are retarded by the addition of PLA. The modified Avrami model is satisfactory in describing the non‐isothermal melt crystallization of the blends, whereas the Ozawa method is not applicable to the blends. The estimated Avrami exponent of the PTT/PLA blends ranges from 3.25 to 4.11, implying that the non‐isothermal crystallization follows a spherulitic‐like crystal growth combined with a complicated growth form. The PTT/PLA blends generally exhibit inferior crystallization rate and superior activation energy compared to pure PTT at the same cooling rate. The greater the PLA content in the PTT/PLA blends, the lower the crystallization rate and the higher the activation energy. Moreover, the introduction of PTT into PLA leads to an increase in the thermal stability behavior of the resulting PTT/PLA blends. Copyright © 2011 Society of Chemical Industry     

Improvement in toughness and crystallization of poly(L‐lactic acid) by melt blending with poly(epichlorohydrin‐co‐ethylene oxide)

Melt blending of poly(lactic acid) (PLA) and poly(epichlorohydrin‐co‐ethylene oxide) copolymers (ECO) was performed to improve the toughness and crystallization of PLA. Thermal and scanning electron microscopy analysis indicated that PLA and ECO were not thermodynamically miscible but compatible to some extent. The addition of a small amount of ECO accelerated the crystallization rate and increased the final crystallinity of PLA in the blends. Significant enhancement in toughness and flexibility of PLA were achieved by the incorporation of the ECO elastomer. When 20 wt% ECO added, the impact strength increased from 5 kJ/m² of neat PLA to 63.9 kJ/m², and the elongation at break increased from 5% to above 160%. The failure mode changed from brittle fracture of neat PLA to ductile fracture of the blend. Rheological measurement showed that the melt elasticity and viscosity of the blend increased with the concentration of ECO. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers.     

Crystallization of poly(3‐hydroxybutyrate) with stereocomplexed polylactide as biodegradable nucleation agent

Crystallization kinetics behavior and morphology of poly(3‐hydroxybutyrate) (PHB) blended with of 2–10 wt% loadings of poly(L ‐ and D ‐lactic acid) (PLLA and PDLA) stereocomplex crystallites, as biodegradable nucleating agents, were studied using differential scanning calorimetry, polarizing‐light optical microscopy (POM), and wide‐angle X‐ray diffraction (WAXD). Blending PLLA with PDLA at 1:1 weight ratio led to formation of stereocomplexed PLA (sc‐PLA), which was incorporated as small crystalline nuclei into PHB for investigating melt‐crystallization kinetics. The Avrami equation was used to analyze the isothermal crystallization of PHB. The stereocomplexed crystallites acted as nucleation sites in blends and accelerated the crystallization rates of PHB by increasing the crystallization rate constant k and decreasing the half‐time (t_1/2). The PHB crystallization was nucleated most effectively with 10 wt% stereocomplexed crystallites, as evidenced byPOM results. The sc‐PLA complexes (nucleated PHB crystals) exhibit much small spherulite sizes but possess the same crystal cell morphology as that of neat PHB based on the WAXD result. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Reactive modification and compatibilization of poly(lactide) and poly(butylene adipate‐co‐terephthalate) blends with epoxy functionalized‐poly(lactide) for blown film applications

Biodegradable blown films comprising of poly(lactide) (PLA) and poly(butylene adipate‐co‐terephthalate) (PBAT) were produced using epoxy functionalized‐poly(lactide) (EF‐PLA) reactive modifiers for rheological enhancement and compatibilization. The epoxy groups on the EF‐PLA modifiers react with PBAT forming an in situ copolymer that localizes at the blend interphase resulting in compatibilization of the polymer blend components. The EF‐PLA modified polymer blends have improved melt strength and the resultant films showed better processability as seen by increased bubbled stability. This allowed for blown films with higher PLA content (70%) compared to the unmodified control films (40%). The static charge build‐up typically experienced with PLA film blowing was decreased with the inclusion of EF‐PLA yielding films with better slip and softness. The compatibilization effect of the EF‐PLA modifiers resulted in significant improvement in mechanical properties. For example, dart test performance was up to four times higher than the control, especially at higher PLA concentrations. Therefore, the rheological enhancement and compatibilization effects of the EF‐PLA reactive modifiers make them ideally suited to create high PLA content films. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43310.     

Effects of poly(butylene adipate‐co‐terephthalate) and ultrafined wollastonite on the physical properties and crystallization of recycled poly(ethylene terephthalate)

Recycled poly(ethylene terephthalate) (rPET), obtained mainly from postconsumer bottles, was melt‐mixed with either poly(butylene adipate‐co‐terephthalate) (PBAT) or PBAT plus ultrafine wollastonite (～5 μm) at different weight ratios on a twin‐screw extruder and then injection‐molded. Among the five rPET/PBAT blends (10–50 wt% PBAT) evaluated, the 80/20 wt% rPET/PBAT blend exhibited the highest tensile strength and degree of crystallinity, a slight increase in the tensile strain, and a remarkable increase in the melt flow index, but a lower tensile modulus and thermal stability with respect to the neat rPET. This blend was subsequently filled with four loading levels of wollastonite (10–40 wt%), where the tensile properties (modulus, strain at break, and strength) and thermal stability of the blend were all improved by the addition of wollastonite in a dose‐dependent manner. Based on differential scanning calorimetry analysis, the crystallinity of rPET in the rPET/PBAT/wollastonite composites decreased in the presence of wollastonite, accompanied with a noticeable increase in the glass transition, cold crystallization, and crystallization temperatures, but only a slight change in the melting temperature was noted compared with those of the neat 80/20 wt% blend. Moreover, the addition of wollastonite at 30 wt% or higher showed a strong reduction in the melt dripping of the composites during combustion. J. VINYL ADDIT. TECHNOL., 23:106–116, 2017. © 2015 Society of Plastics Engineers     

Toward environment‐friendly composites of poly(ε‐caprolactone) reinforced with stereocomplex‐type poly(l‐lactide)/poly(d‐lactide)

In this work, stereocomplex‐poly(l ‐ and d ‐lactide) (sc‐PLA) was incorporated into poly(ε‐caprolactone) (PCL) to fabricate a novel biodegradable polymer composite. PCL/sc‐PLA composites were prepared by solution casting at sc‐PLA loadings of 5–30 wt %. Differential scanning calorimetry (DSC) and wide‐angle X‐ray diffraction (WAXD) demonstrated the formation of the stereocomplex in the blends. DSC and WAXD curves also indicated that the addition of sc‐PLA did not alter the crystal structure of PCL. Rheology and mechanical properties of neat PCL and the PCL/sc‐PLA composites were investigated in detail. Rheological measurements indicated that the composites exhibited evident solid‐like response in the low frequency region as the sc‐PLA loadings reached up to 20 wt %. Moreover, the long‐range motion of PCL chains was highly restrained. Dynamic mechanical analysis showed that the storage modulus (E′) of PCL in the composites was improved and the glass transition temperature values were hardly changed after the addition of sc‐PLA. Tensile tests showed that the Young's modulus, and yield strength of the composites were enhanced by the addition of sc‐PLA while the tensile strength and elongation at break were reduced. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40208.     

Isothermal crystallization kinetics of biodegradable poly(lactic acid)/poly(ε‐caprolactone) blends compatibilized with low‐molecular weight block copolymers

The isothermal crystallization kinetics of biodegradable blends made of poly(lactic acid) (PLA) and poly(ε‐caprolactone) (PCL) compatibilized with two different low molecular weight block copolymers, that is, ε‐caprolactone/tetramethylene ether glycol and ε‐caprolactone/aliphatic polycarbonate (CB), was done. Blends were prepared by melt mixing in an extruder, while isothermal crystallization kinetics and morphologies were investigated by thermal (differential scanning calorimetry) and thermo‐optical (quantitative polarized light optical microscopy [qPLOM]) quantitative methods. Data were analyzed using the Avrami equation, revealing 2D and 3D growth and simultaneous heterogeneous nucleation. The presence of low molecular weight compatibilizers, that is, 2,000 g mol^?1, accelerated the PLA crystallization rate by two to threefold when compared with neat PLA, with high degrees of crystallinity (40–43%) as confirmed by PLOM images. The activation energy (E_a) showed that PCL inhibits PLA crystallization; however, the addition of block copolymers used as compatibilizers of the blends reduced E_a values, increasing the chain mobility of PLA and thus increasing the crystallization rate. POLYM. ENG. SCI., 59:E161–E169, 2019. © 2018 Society of Plastics Engineers     

Thermal,mechanical, and rheological properties of polylactide/poly(1,2‐propylene glycol adipate)

Polylactide (PLA) was melt blended with poly(1,2‐propylene glycol adipate) (PPA) in a Thermo‐Haake mixer. Thermal, mechanical, and rheological properties of the blends were investigated by means of differential scanning calorimetry, dynamic mechanical analysis, tensile test, and small amplitude oscillatory shear rheometry. PPA lowered the glass transition temperature and increased the ability of PLA to cold crystallization. With the increase in PPA content (5–25 wt%), the blends showed decreased tensile strength and Young's modulus; however, impact strength and elongation‐at‐break along were dramatically increased due to the plastic deformation. Morphological results of PLA/PPA blends showed that PPA was good compatible with PLA. The plasticization effect of PPA was also manifested by the lowering of dynamic storage modulus and viscosity in the melt state of the blends compared with neat PLA. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Blends of polylactide and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) with low content of hydroxyvalerate unit: Morphology,structure, and property

The Polylactide (PLA)/poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) blends with four different weight ratios were prepared by melt mixing. PLA and PHBV in PLA/PHBV blends were immiscible while the weak interaction between PLA and PHBV existed. The PHBV domains below 2 μm were dispersed in PLA matrix uniformly. The addition of PHBV made the crystallization of PLA easier due to PHBV acting as nucleating agent. PLA spherulites in PLA/PHBV blends presented various banded structures. In addition, the crystallinity of neat PLA was lower than those of PLA/PHBV blends. With the increase of PHBV content in PLA/PHBV blends, the crystallinity of PLA/PHBV blends increased. PHBV could enhance significantly the toughness of PLA. However, with the increase of PHBV content, the yield stress (σ_y), tensile modulus (E), and the yield strain (ε_y) of PLA/PHBV blends decreased gradually. In addition, incorporation of PHBV to PLA caused a transformation from an optical transparent to an opaque system. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42689.     

Preparation,crystallization, and properties of biodegradable poly(butylene adipate‐co‐terephthalate)/organomodified montmorillonite nanocomposites

Intercalated and exfoliated nanocomposites of biodegradable poly(butylene adipate‐co‐terephthalate) (PBAT) and Cloisite 30B (C30B) were fabricated by a solution‐casting method to study the effects of the clay loading on the crystallization behavior, thermal stability, and dynamic mechanical properties of PBAT in PBAT/C30B nanocomposites. X‐ray diffraction and transmission electron microscopy results indicated the formation of exfoliated nanocomposites at low clay loadings (<5 wt %) and a mixture of exfoliated and intercalated nanocomposites with a clay content of 8 wt % throughout the PBAT matrix. Nonisothermal melt crystallization studies indicated that C30B enhanced the crystallization of PBAT, apparently because of a heterogeneous nucleation effect. Moreover, an attempt was made to quantitatively study the influence of the presence of C30B and its contents on the nucleation activity of PBAT in the PBAT/C30B nanocomposites. The thermal stability of PBAT decreased slightly in the nanocomposites. However, the storage modulus of PBAT apparently increased with the C30B loading increasing in the PBAT/C30B nanocomposites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011