Morphology and Mechanical Properties of iPP/Silica Composites Modified with (Styrene-b-ethylene-co-butylene-b-styrene) Grafted with Maleic Anhydride

The effects of different silica grades and elastomer content on interfacial properties, morphology and mechanical properties of polypropylene/silica 96/4 composites modified with added 5, 10, 15, and 20% of poly(styrene-b-ethylene-co-butylene-b-styrene) grafted with maleic anhydride (SEBS-g-MA) were investigated. The iPP/silica/SEBS-g-MA composites were designed by adding four silica fillers differing in size (nano- vs. micro-) and in surface properties (hydrophilic vs. hydrophobic) and SEBS-g-MA that was used as a proven effective impact modifier and compatibilizer simultaneously. The morphology of every composite was a spectrum of several morphologies rather than one exclusive morphology. Good concordance between observed and predicted morphology indicated that the morphology of a particular composite was controlled primarily by interfacial properties. Tensile and impact properties were influenced primarily by competitive effects of a stiff filler and tough SEBS-g-MA elastomer. Increased impact strength and strain at break caused by adding SEBS-g-MA indicated a significant overcoming of the elastomeric toughening effect in relation to the filler’s stiffening effect.     

Wollastonite‐reinforced polypropylene composites modified with novel metallocene EPR copolymers. II. Mechanical properties and adhesion

Mechanical properties and adhesion phenomena of isotactic polypropylene/wollastonite/metallocene propylene‐ethylene copolymers (iPP/W/EPR) composites were studied as a function of metallocene propylene‐based copolymers content from 0 to 20 vol%. The composites with different surface treated wollastonites and two types of EPR have shown similar behavior of most mechanical properties except elongation at break and impact strength respective of the difference in some characteristics of used EPR elastomers. The increase and the difference in elongation at break could be explained by renewed spherulitic morphology of the iPP matrix. Stronger interactions between EPR‐1 and two used types of wollastonites than between EPR‐2 and corresponding wollastonites concluded from the surface properties led to the difference in impact strength behavior. The determined mechanical properties confirm the assumption coming out of structural investigations that metallocene EPR elastomers are rather efficient impact modifiers than encapsulation compatibilizers for the iPP/wollastonite composites. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Mechanical properties of glass bead‐ and wollastonite‐filled isotactic‐polypropylene composites modified with thermoplastic elastomers

Mechanical properties of the isotactic‐polypropylene/glass bead (iPP/GB) and iPP/wollastonite (iPP/W) composites modified with thermoplastic elastomers, the poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) copolymer (SEBS) and corresponding block copolymer grafted with maleic anhydride (SEBS‐g‐MA), were investigated. An increase in toughness of iPP with the elastomers was associated with a decrease in rigidity and strength. Mechanical performance of iPP increased more with acicular W than with spherical GB due to reinforcing effect of W. Comparing the (iPP/GB)/SEBS and (iPP/W)/SEBS composites having the separate microstructure, strength and toughness values of the iPP/GB and iPP/W composites increased more with SEBS‐g‐MA at the expense of rigidity due to the core‐shell microstructure with strong interfacial adhesion. Moreover, the iPP/W composite exhibited superior mechanical performance with 2.5 and 5 vol% of SEBS‐g‐MA because of a positive synergy between the core‐shell microstructure and reinforcing effect of acicular W. The extended models revealed that the elastomer and filler particles in the (iPP/GB)/SEBS and (iPP/W)/SEBS composites acted individually due to the separate microstructure. However, the rigid GB and W particles encapsulated with the thick elastomer interlayer (R₀/R₁ = 0.91) in the (iPP/GB)/SEBS‐g‐MA and (iPP/W)/SEBS‐g‐MA composites acted like neither big elastomer particles nor like individual rigid particles, inferring more complicated failure mechanisms in the core‐shell composites. POLYM. COMPOS., 31:1285–1308, 2010. © 2010 Society of Plastics Engineers     

Polypropylene/silica micro‐ and nanocomposites modified with poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene)

The effects of different silica loadings and elastomeric content on interfacial properties, morphology and mechanical properties of polypropylene/silica 96/4 composites modified with 5, 10, 15, and 20 vol % of poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) SEBS added to total composite volume were investigated. Four silica fillers differing in size (nano‐ vs. micro‐) and in surface properties (untreated vs. treated) were chosen as fillers. Elastomer SEBS was added as impact modifier and compatibilizer at the same time. The morphology of ternary polymer composites revealed by light and scanning electron microscopies was compared with morphology predicted models based on interfacial properties. The results indicated that general morphology of composite systems was determined primarily by interfacial properties, whereas the spherulitic morphology of polypropylene matrix was a result of two competitive effects: nucleation effect of filler and solidification effect of elastomer. Tensile and impact strength properties were mainly influenced by combined competetive effects of stiff filler and tough SEBS elastomer. Spherulitic morphology of polypropylene matrix might affect some mechanical properties additionally. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41486.     

Polypropylene Blends with m-EPR Copolymers: Structure,Morphology and Thermal Properties

The effects of different contents of two metallocene propylene-based m-EPR elastomers on structure, morphology, thermal, and dynamic mechanical properties of the isotactic polypropylene/m-EPR blends were investigated. The both m-EPR copolymers have been built in isotactic polypropylene matrix as amorphous phase. However, the nucleation effect at lowest addition (2.5?vol%) and the solidification effect along with increased m-EPR’s additions have caused changes of the crystallinity degree and the size of spherulites in the isotactic polypropylene matrix. Higher degree of miscibility/compatibility of the isotactic polypropylene/m-EPR2, with lower viscosity has been observed. Homogeneous dispersion of m-EPR particles as well as their radial distribution has been observed.     

Mechanical properties and morphologies of PP/mPE/filler composites

Because of the poor impact behavior of polypropylene (PP) at low temperatures, the blending of PP with metallocene‐polymerized polyethylene (mPE) elastomers was investigated in this study. However, a reduced modulus of the overall blend was inevitable because of the addition to elastomers. To obtain a balance of the properties, we introduced rigid inorganic fillers to PP/mPE blends. The performance of the composites was characterized with tensile and Charpy notched impact tests, and the fracture morphology was examined with scanning electron microscopy. The results showed that the effects of fillers in a brittle matrix and in a ductile matrix were quantitatively different. For PP/mPE/filler ternary composites, the dependence of Young's modulus and yield strength on CaCO₃ content was not significant compared with that of PP/filler binary composites, whereas the elongation at break and tensile toughness at room temperature for PP/mPE/filler systems were more improved. The impact strength of the PP/mPE blends filled with untreated glass beads and CaCO₃ at a low temperature was lowered because of the weak interfacial bond. However, the values of the impact strength of the PP/mPE/filler composites at a low temperature remained at a high level compared with that of pure PP. In particular, a PP/mPE blend filled with surface‐treated kaolin had a higher low‐temperature impact toughness than the unfilled blend. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 3029–3035, 2002; DOI 10.1002/app.2333     

Morphology of polypropylene/silica nano‐ and microcomposites

The aim of this study was to compare the effects of different silica grades on the structure and morphology of isotactic polypropylene (iPP)/silica composites to better understand their structure–property relationships. Isotactic polypropylene composites with 2, 4, 6, 8 vol % of added silica fillers differing in particle size (micro‐ vs. nanosilica) and surface modification (untreated vs. treated surface) were prepared by nonisothermal compression molding and characterized by different methods. The addition of all silica fillers grades to the iPP matrix significantly influenced the spherulitic morphology, while phase characteristics of the iPP matrix seemed to be unaffected. Surface modification of silica fillers exhibited stronger effects on spherulite size than size of silica particles. Nonpolar silica particles, more miscible or compatible with iPP chains than polar silica particles, enabled better spherulitic growth. The spherulite sizes tended to reach equal values at 8 vol % of added silicas showing that spherulite size became independent of filler concentration and surface modification above optimum filler concentration. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effects of silica on the morphology,structure, and properties of thermoplastic cassava starch/poly(vinyl alcohol) blends

Thermoplastic cassava starch (TPS)/poly(vinyl alcohol) (PVA)/silica (SiO₂) composites were prepared by a melt‐mixing method. The effects of the content and surface properties of SiO₂ on the processing, mechanical properties, thermal stability, morphology, and structure of the TPS/PVA/SiO₂ composites were investigated. With increasing SiO₂ content, the plasticizing times of the TPS/PVA/SiO₂ composites were shortened. After the SiO₂ surface was treated with a silane coupling agent (KH550), the plasticizing times of the TPS/PVA/SiO₂ composites decreased significantly. The tensile strength, elongation at break, and Young's modulus of the TPS/PVA/SiO₂ composites increased. The mechanical properties of the TPS/PVA/SiO₂ composites containing treated SiO₂ were higher than those with untreated SiO_2. The thermal decomposition temperatures of the TPS/PVA/SiO₂ composites were improved with the addition of SiO₂. The presence of inorganic fillers was beneficial to the improvement of the thermal stability of the polymers. The reaction between the treated SiO₂ and the starch molecules was beneficial to the formation of more stable structures. The treated SiO₂ indicated good interfacial adhesion and uniform dispersion in the matrix. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44020.     

Compatibilization of PP/elastomer/microsilica composites with functionalized polyolefins: Effect on microstructure and mechanical properties

The morphology and mechanical properties of polypropylene/elastomer/silica composites were investigated with the aim of improving stiffness and impact resistance. Two different types of silica were tested: Precipitated silica and polymer grade microsilica (silica fume). The composites were compatibilized with commercial polypropylene and polyethylene containing maleic anhydride functionality as a means of controlling their microstructure and ultimately their mechanical properties. Comparisons were made with surface coated silica and hydroxyl-functionalized copolymers prepared with metallocene catalysts. The effect of adding the polymeric compatibilizers was assessed by morphology studies, thermal analysis and mechanical testing. Significant improvements in impact strength were obtained by tailoring the microstructure of polypropylene/elastomer/microsilica composites. With introduction of PP-g-MAH as compatibilizer, stiffness was enhanced simultaneously with impact strength. DSC curves of crystallization provided evidence to support the formation of different microstructures.     

Investigation on the mechanical performances of ternary nylon 6/SEBS elastomer/nano‐SiO2 hybrid composites with controlled morphology

The distribution of maleated styrene‐hydrogenated butadiene‐styrene (mSEBS) elastomer and nano‐SiO₂ in nylon 6 matrix was controlled by varying the blending procedure. Nano‐SiO₂ particles with different surface properties (hydrophilic versus hydrophobic) were adopted to adjust their interactions with other components. Two different structures, separate dispersion of nano‐SiO₂ and elastomer particles as well as encapsulation of nano‐SiO₂ fillers by the elastomer, were obtained. The structures were confirmed through scanning electron microscope (SEM) investigation. The mechanical measurement results showed that the microstructure and the interactions among the components had dramatic influences on the final mechanical properties, especially Izod fracture toughness, for the ternary nanocomposites. The nanocomposites containing hydrophilic nano‐SiO₂ had better mechanical performances compared with the composites filled with hydrophobic SiO₂ when they were in the same microstructure. The nanocomposites with separate dispersion structure showed higher stiffness compared with those of encapsulation type. However, the separately dispersed nano‐SiO₂ particles restricted the cavitation of elastomer phases that led to low toughening effectiveness. The difference of cavitation intensity for elastomer phase was revealed by SEM investigation on the facture surfaces for the nanocomposites with the two different microstructures. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Mechanical,dielectric, and thermal properties of fluorosilicone rubber composites filled with silica/multiwall carbon nanotube hybrid fillers

In this work, hybrid fillers consist of modified silica (SiO₂) and multiwalled carbon nanotube (MWCNT) were used to improve the mechanical, dielectric, and thermal properties of fluorosilicone (FSR) composites via a direct mechanical mixing method. With the increase of CNT loading in SiO₂/CNT hybrid loading ratio, the tensile properties, dielectric constant, electrical conductivity, and thermal properties all increase without a sharp sacrifice of flexibility. The dielectric constant of FSR-S15/C5 achieved 7,370 @1 kHz, which is about four orders of the FSR-S20, and the dielectric loss remains as low as 0.676 @1 kHz. Therefore, the linkage of SiO₂ and FSR chains not only enhances the interfacial interaction between the fillers and FSR matrix but also decreases the agglomeration of the fillers in matrix. What is more, modified SiO₂ and CNT were designed as the effective hybrid filler to improve the performance of the polymeric matrix through synergic effect.     

Preparation by melt mixing and characterization of isotactic polypropylene/SiO2 nanocomposites containing untreated and surface‐treated nanoparticles

In the present study two series of isotactic polypropylene (iPP)/SiO₂ nanocomposites containing 1, 2.5, 5, 7.5, and 10 wt % SiO₂ nanoparticles were prepared by melt‐mixing on a twin‐screw corotating extruder. In the first series untreated fumed silica nanoparticles were used, whereas in the second nanoparticles were surface‐treated with dimethyldichlorosilane. In both cases, the average size of the primary nanoparticles was 12 nm. Tensile and impact strength were found to increase and to be affected mainly by the type and content of silica nanoparticles. A maximum was observed, corresponding to samples containing 2.5 wt % SiO₂. These findings are discussed in light of the SEM and TEM observations. By increasing the amount of nanoparticles, large aggregates of fumed silica could be formed, which may explain the reduction of mechanical properties with higher concentrations of SiO₂. However, it was found that surface‐treated nanoparticles produced larger aggregates than did those derived from untreated nanoparticles, despite the increased adhesion of the iPP matrix, as was postulated from yield strength. This behavior negatively affected mechanical properties. In addition, an effort was made to determine if toughening theories, mainly the critical interparticle distance for rubber toughening or composites, also might be applicable in nanocomposites. From DSC measurements it was demonstrated that silica nanoparticles acted as effective nucleating agents, increasing the crystallization rate and the degree of crystallinity of iPP. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2684–2696, 2006     

Effect of different fillers on physical,mechanical, and optical properties of styrenic‐based thermoplastic elastomers

The effects of different fillers on physical, mechanical, and optical properties of styrenic‐based thermoplastic elastomers were investigated by experimental study. Poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] block copolymer (SEBS)‐based thermoplastic elastomer composites were prepared in a co‐rotating intermeshing twin‐screw extruder, using silica and calcite as filler materials with three different particle sizes. The loading ratios in the composites were varied. Hardness, density, tensile strength, tear strength, compression set, wear resistance, transmittance, and haze measurements were performed. Thermal properties and morphological structure were investigated by differential scanning calorimeter (DSC) and scanning electron microscopy (SEM), respectively. The results show that, an interaction between silica and the polymer matrix exists, whereas calcite does not show any interaction with the polymer. Therefore, it is concluded that, calcium carbonate can be used in the composite as filler for cost efficiency, whereas silica can be used as reinforcing material in SEBS‐based thermoplastic elastomer composites, when optical properties are also concerned. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers     

Microstructural characteristics of glass bead‐ and wollastonite‐filled isotactic‐polypropylene composites modified with thermoplastic elastomers

Microstructural characteristics of isotactic‐polypropylene/glass bead (iPP/GB) and iPP/wollastonite (iPP/W) composites modified with thermoplastic elastomers, poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) copolymer (SEBS) and corresponding block copolymer grafted with maleic anhydride (SEBS‐g‐MA), were investigated. Scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and dynamic mechanical analyses (DMA) showed that the iPP/SEBS and iPP/SEBS‐g‐MA blends were partially compatible two‐phase systems. Well‐dispersed spherical GB and acicular W particles without evidence of interfacial adhesion were observed in the iPP/GB and iPP/W binary composites respectively. Contrary to the blends, melt flow rates of the iPP/GB and PP/W composites decreased more with SEBS‐g‐MA than with SEBS because of enhanced interfacial adhesion with SEBS‐g‐MA elastomer. The SEM analyses showed that the ternary composites containing SEBS exhibited separate dispersion of the rigid filler and elastomer particles (i.e., separate microstructure). However, SEBS‐g‐MA elastomer not only encapsulated the spherical GB and acicular W particles completely with strong interfacial adhesion (i.e., core‐shell microstructure) but also dispersed separately throughout iPP matrix. In accordance with the SEM observations, the DSC and DMA revealed quantitatively that the rigid filler and SEBS particles in iPP matrix acted individually, whereas the rigid filler particles in the ternary composites containing SEBS‐g‐MA acted like elastomer particles because of the thick elastomer interlayer around the filler particles. The Fourier transform infrared analyses revealed an esterification reaction inducing the strong interfacial adhesion between the SEBS‐g‐MA phase and the filler particles. POLYM. COMPOS., 31:1265–1284, 2010. © 2009 Society of Plastics Engineers     

Modification of polyethylene–octene elastomer by silica through a sol–gel process

In this study, tetraethoxysilane (TEOS) and a metallocene polyethylene–octene elastomer (POE) were chosen as the ceramic precursor and the continuous phase, respectively, for the preparation of new hybrids by an in situ sol–gel process. To obtain a better hybrid, a maleic anhydride‐grafted polyethylene–octene elastomer (POE‐g‐MAH), used as the continuous phase, was also investigated. Characterizations of POE‐g‐MAH/SiO₂ and POE/SiO₂ hybrids were performed by Fourier transform infrared (FTIR) and ²⁹Si solid‐state nuclear magnetic resonance (NMR) spectrometers, a differential scanning calorimeter (DSC), a thermogravimetry analyzer, and an Instron mechanical tester. The results showed that the POE‐g‐MAH/SiO₂ hybrid could improve the properties of the POE/SiO₂ hybrid because the interfacial force between the polymer matrix and the silica network was changed from hydrogen bonds into covalent Si? O? C bonds through dehydration of hydroxy groups in POE‐g‐MAH with residual silanol groups in the silica network. The existence of covalent Si? O? C bonds was proved by FTIR spectra. For the POE/SiO₂ and POE‐g‐MAH/SiO₂ hybrids, maximum values of the tensile strength and the glass transition temperature were found at 9 wt % SiO₂ since a limited content of silica might be linked with the polymer chains through the covalent bond. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 966–972, 2003     

Silicone rubbers for dielectric elastomers with improved dielectric and mechanical properties as a result of substituting silica with titanium dioxide

One prominent method of modifying the properties of dielectric elastomers (DEs) is by adding suitable metal oxide fillers. However, almost all commercially available silicone elastomers are already heavily filled with silica to reinforce the otherwise rather weak silicone network and the resulting metal oxide filled elastomer may contain too much filler. We therefore explore the replacement of silica with titanium dioxide to ensure a relatively low concentration of filler. Liquid silicone rubber (LSR) has relatively low viscosity, which is favorable for loading inorganic fillers. In the present study, four commercial LSRs with varying loadings of silica and one benchmark room-temperature vulcanizable rubber (RTV) were investigated. The resulting elastomers were evaluated with respect to their dielectric permittivity, tear and tensile strengths, electrical breakdown, thermal stability and dynamic viscosity. Filled silicone elastomers with high loadings of nano-sized titanium dioxide (TiO₂) particles were also studied. The best overall performing formulation had 35 wt.% TiO₂ nanoparticles in the POWERSIL® XLR LSR, where the excellent ensemble of relative dielectric permittivity of 4.9 at 0.1 Hz, breakdown strength of 160 V µm^?1, tear strength of 5.3 MPa, elongation at break of 190%, a Young’s modulus of 0.85 MPa and a 10% strain response (simple tension) in a 50 V μm^?1 electric field was obtained.     

Rheological behaviors of glass bead‐ and wollastonite‐filled polypropylene composites modified with thermoplastic elastomers

Steady‐ and oscillatory‐shear rheological behaviors of polypropylene/glass bead (PP/GB) and PP/wollastonite (PP/W) melts modified with thermoplastic elastomers, poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) copolymer (SEBS) and the corresponding block copolymer grafted with maleic anhydride (SEBS‐g‐MA), were examined by means of a parallel‐plate rheometer. With adding the elastomers (SEBS and SEBS‐g‐MA) and fillers (spherical GB and acicular W) to PP, viscosity especially at low shear rates and shear‐thinning flow behavior at high shear rates were pronounced as evidenced quantitatively by Carreau–Yasuda (CY) parameters, but Cox–Merz analogy became weakened. Besides, melt‐elasticity in terminal region and relaxation time (t_c) in crossing point increased, indicating an enhancement in quasi‐solid behavior of molten PP. Comparing with the elastomers, rheological behaviors of molten PP were more influenced with adding the rigid fillers, especially with W due to distinct acicular shape of W particles. SEBS‐g‐MA elastomer more affected rheological behaviors of the ternary composites than SEBS elastomer, implying that SEBS elastomer and the filler particles behaved individually (i.e., development of separate microstructure) in (PP/GB)/SEBS and (PP/W)/SEBS ternary composites, but core‐shell microstructure developed with strong interfacial adhesion by adding SEBS‐g‐MA elastomer, and the filler particles encapsulated with the thick SEBS‐g‐MA elastomer interlayer (i.e., core‐shell particles) acted like neither big elastomer particles nor like individual rigid particles in melt‐state. Moreover, effects of SEBS‐g‐MA elastomer reached a maximum on rheological behaviors of (PP/W)/SEBS‐g‐MA ternary composite, indicating a synergy between core‐shell microstructure and acicular W particles. Correlations between oscillatory‐shear flow properties and microstructures of the blends and composites were evaluated using Cole–Cole (CC), Han–Chuang (HC), and van Gurp–Palmen (vGP) plots. COMPOS., 2012. © 2012 Society of Plastics     

Improved dispersion and interfacial interaction of SiO2@polydopamine fillers in polytetrafluoroethylene composites for reduced thermal expansion and suppressed dielectric deterioration

Copper-clad laminate (CCL) comprised of copper foil and polytetrafluoroethylene (PTFE) faces severe thermal expansion mismatch due to the discrepancy in coefficient of thermal expansion (CTE) between the two components. Incorporating inorganic fillers with low CTE into PTFE has been proved to be a promising way to achieve the goal. However, it is a challenge to achieve homogeneous distribution and good interfacial interaction of fillers in PTFE composites owing to the characteristics of PTFE emulsion. In this work, core@shell structured SiO₂@polydopamine fillers (SiO₂@PDA) were synthesized and incorporated into PTFE matrix to form SiO₂@PDA/PTFE composites. Due to the presence of PDA shell, SiO₂@PDA exhibited improved dispersion and interfacial interaction, contributing to the reduced CTE and suppressed dielectric deterioration of SiO₂@PDA/PTFE composites. With 40 vol% of filler, the CTE of SiO₂@PDA/PTFE composite was efficiently reduced (50%), coupled with a limited sacrifice of only 2% and 40% of increments for dielectric constant (D_k, 2.3) and dielectric loss (D_f, 2.4 × 10⁻³), respectively (@40 GHz), as compared with that of the corresponding SiO₂/PTFE composite. The fillers and composites were comprehensively characterized to verify the mechanism of CTE and dielectric properties of the composites.     

Enhanced interfacial strength and mechanical properties of carbon fiber composites by introducing functionalized silica nanoparticles into the interface

Introducing nanoparticles onto the surface of carbon fibers (CFs) is a useful method for enhancing the quality of fiber-matrix interface. In this work, a liquid sizing agent containing functionalized silica nanoparticles (SiO₂) was well prepared to improve interfacial strength and mechanical properties of composites. In order to enhance the dispersion of SiO₂ nanoparticles in sizing agent, SiO₂ nanoparticles were chemically grafted with 3-aminopropyltriethoxysilane (APS), and then silanized silica (SiO₂-APS) was introduced into the interphase by a conventional sizing process as well. Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and thermogravimetric analysis (TGA) confirmed the successful preparation of SiO₂-APS. Scanning electron microscopy (SEM) showed that a uniform distribution of SiO₂-APS on the fiber surface and the increased surface roughness. The sized fibers (CF/SiO₂-APS) exhibited a high surface free energy and good wettability based on a dynamic contact angle testing. Interfacial microstructure and mechanical properties of untreated and sized CFs composites were investigated. Simultaneous enhancements of interlaminar shear strength (ILSS) and impact toughness of CF/SiO₂-APS composites were achieved, increasing 44.79% in ILSS and 31.53% in impact toughness compared to those of untreated composites. Moreover, flexural strength and modulus of composites increased by 32.22 and 50.0% according to flexural test. In addition, the hydrothermal aging resistance of CF/SiO₂-APS composites has been improved significantly owing to the introduced Si-O-Si bonds at the interface.     

Novel approach to fibrillation of LCP in an LCP/PP blend

A novel concept of improving shear‐induced fibrillation of liquid crystalline polymer (LCP) in LCP/thermoplastic blend systems was introduced. Silica fillers (SiO₂) were added to an LCP/polypropylene (PP) system to serve as a viscosity thickening agent and to improve the fibrillation of the LCP phase. The formation of LCP fibrils was found to enhance with the incorporation of 5–15 wt % of fillers. The presence of LCP fibrils improved the flow properties of the LCP/PP/SiO₂ composites. It was evident from the rheological and morphological studies that the addition of silica led to an increase of the aspect ratio of the LCP fibrils, which, in turn, should improve their effectiveness as reinforcements and/or toughening agents. Substantial improvement in LCP aspect ratio was achieved by the introduction of hydrophobic SiO₂ fillers in the PP/LCP blends. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2070–2078, 2002