Photobiodegradation of low‐density polyethylene/banana starch films

The effects of the starch content, photosensitizer content, and compatibilizer on the photobiodegradability of low‐density polyethylene (LDPE) and banana starch polymer blend films were investigated. The compatibilizer and photosensitizer used in the films were PE‐graft‐maleic anhydride (PE‐g‐MA) and benzophenone, respectively. Dried banana starch at 0–20% (w/w) of LDPE, benzophenone at 0–1% (w/w) of LDPE, and PE‐g‐MA at 10% (w/w) of banana starch were added to LDPE. The photodegradation of the blend films was performed with outdoor exposure. The progress of the photodegradation was followed by determining the carbonyl index derived from Fourier transform IR measurements and the changes in tensile properties. Biodegradation of the blend films was investigated by a soil burial test. The biodegradation process was followed by measuring the changes in the physical appearance, weight loss, and tensile properties of the films. The results showed that both photo‐ and biodegradation rates increased with increasing amounts of banana starch, whereas the tensile properties of the films decreased. The blends with higher amounts of benzophenone showed higher rates of photodegradation, although their biodegradation rates were reduced with an increase in benzophenone content. The addition of PE‐g‐MA into polymer blends led to an increase in the tensile properties whereas the photobiodegradation was slightly decreased compared to the films without PE‐g‐MA. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2725–2736, 2006     

Modification of recycled high‐density polyethylene by low‐density and linear‐low‐density polyethylenes

The present study investigated mixed polyolefin compositions with the major component being a post‐consumer, milk bottle grade high‐density polyethylene (HDPE) for use in large‐scale injection moldings. Both rheological and mechanical properties of the developed blends are benchmarked against those shown by a currently used HDPE injection molding grade, in order to find a potential composition for its replacement. Possibility of such replacement via modification of recycled high‐density polyethylene (reHDPE) by low‐density polyethylene (LDPE) and linear‐low‐density polyethylene (LLDPE) is discussed. Overall, mechanical and rheological data showed that LDPE is a better modifier for reHDPE than LLDPE. Mechanical properties of reHDPE/LLDPE blends were lower than additive, thus demonstrating the lack of compatibility between the blend components in the solid state. Mechanical properties of reHDPE/LDPE blends were either equal to or higher than calculated from linear additivity. Capillary rheological measurements showed that values of apparent viscosity for LLDPE blends were very similar to those of the more viscous parent in the blend, whereas apparent viscosities of reHDPE/LDPE blends depended neither on concentration nor on type (viscosity) of LDPE. Further rheological and thermal studies on reHDPE/LDPE blends indicated that the blend constituents were partially miscible in the melt and cocrystallized in the solid state.     

Low‐density polyethylene/plasticized tapioca starch blends with the low‐density polyethylene functionalized with maleate ester: Mechanical and thermal properties

In this study, the mechanical and thermal properties of low‐density polyethylene (LDPE)/thermoplastic tapioca starch blends were determined with LDPE‐g‐dibutyl maleate as the compatibilizer. Mechanical testing for the evaluation of the impact strength and tensile properties was carried our as per standard ASTM methods. Thermogravimetric analysis and differential scanning calorimetry were also used to assess the thermal degradation of the blends. Scanning electron micrographs were used to analyze fracture and blend morphologies. The results show significant improvement in the mechanical properties due to the addition of the compatibilizer, which effectively linked the two immiscible blend components. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1109–1120, 2006     

Morphology and rheological properties of compatibilized low‐density polyethylene/linear low‐density polyethylene/thermoplastic starch blends

Morphology and rheological properties of low‐density polyethylene/linear low‐density polyethylene/thermoplastic starch (LDPE/LLDPE/TPS) blends are experimentally investigated and theoretically analyzed using rheological models. Blending of LDPE/LLDPE (70/30 wt/wt) with 5–20 wt % of TPS and 3 wt % of PE‐grafted maleic anhydride (PE‐g‐MA) as a compatibilizer is performed in a twin‐screw extruder. Scanning electron micrographs show a fairly good dispersion of TPS in PE matrices in the presence of PE‐g‐MA. However, as the TPS content increases, the starch particle size increases. X‐ray diffraction patterns exhibit that with increase in TPS content, the intensity of the crystallization peaks slightly decreases and consequently crystal sizes of the blends decrease. The rheological analyses indicate that TPS can increase the elasticity and viscosity of the blends. With increasing the amount of TPS, starch particles interactions intensify and as a result the blend interface become weaker which are confirmed by relaxation time spectra and the prediction results of emulsion Palierne and Gramespacher‐Meissner models. It is demonstrated that there is a better agreement between experimental rheological data and Coran model than the emulsion models. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44719.     

Effect of propylation of starch with different degrees of substitution on the properties and characteristics of starch‐low density polyethylene blend films

Corn starch was modified by propylation and degree of substitution (DS) of four starch modifications were 0.61, 1.56, 2.27, and 2.51. Different films were prepared by blending native and propylated starch with low‐density polyethylene (LDPE). The mechanical properties, thermal properties, water absorption capacity, and biodegradability of the blend films varied with the quantity of starch as well as DS. Tensile strength, elongation, and melt flow index of propylated starch blend films were higher compared to the corresponding native starch blend film. These properties improved with increase in DS from 1.56 to 2.51. Propylated starch blend films were found thermally stable than native starch blend films. There was a decrease in water absorption capacity for the films containing propylated starch at high DS. Enzymatic and soil burial degradation results showed that biodegradability of starch‐LDPE films increased with the increase in the starch concentration but it decreased with increase in the DS. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Biodegradation of low‐density polyethylene/thermoplastic starch foams before and after electron beam irradiation

Foamy low‐density polyethylene/plasticized starch (LDPE/PLST) blends at different compositions were produced in the presence of azodicarbonamide (ACA) compound as foaming agent. The LDPE/PLST blends before and after electron beam irradiation were investigated in terms of mechanical properties, bulk density, and structure morphology. Moreover, the biodegradability of these materials was evaluated by the soil burial test for 2 months, in which the buried sheets were also examined by scanning electron microscopy (SEM). The results showed that the increase of PLST content from 24 to 30% was accompanied by a decrease in the yield and break stresses of 10 and 20% for the unirradiated blends without the foaming agent, respectively. Further decrease in these mechanical parameters was observed after the foaming process. The bulk density, void fraction, cell size measurements as well as the examination by SEM illustrate clearly the cell growth of the foam structure. The soil burial test and SEM micrographs indicate the growth of microorganisms overall the blend sheets and that the blend was completely damaged after two months of burying. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Transparent low‐density polyethylene/starch nanocomposite films

Low‐density polyethylene (LDPE)/starch nanocomposite films were prepared by melt extrusion process. The first step includes the preparation of starch–clay nanocomposite by solution intercalation method. The resultant product was then melt mixed with the main matrix, which is LDPE. Maleic anhydride‐grafted polyethylene (MAgPE), produced by reactive extrusion, was used as a compatibilizer between starch and LDPE phases. The effects of using compatibilizer, clay, and plasticizers on physico‐mechanical properties were investigated. The results indicated that the initial intercalation reaction of clay layers with starch molecules, the conversion of starch into thermoplastic starch (TPS) by plasticizers, and using MAgPE as a compatibilizer provided uniform distribution of both starch particles and clay layers, without any need of alkyl ammonium treatment, in LDPE matrix. The nanocomposite films exhibited better tensile properties compared to clay‐free ones. In addition, the transparency of LDPE film did not significantly change in the presence of TPS and clay particles. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation and characterization of low‐density polyethylene/banana starch films containing compatibilizer and photosensitizer

Composite films containing various percentages of banana starch and low‐density polyethylene (LDPE) were prepared. The effects of the compatibilizer, banana starch content, and photosensitizer content on the thermal and tensile properties of these films were investigated. The banana starch content was varied from 5 to 20 wt % of LDPE, whereas benzophenone was added as a photosensitizer in three different amounts (0.25, 0.5, and 1 wt %) based on LDPE. In these films PE‐graft‐maleic anhydride (PE‐g‐MA) was used as a compatibilizer at 10 wt % banana starch. It was found that the thermal stability of the composite films remained unchanged with respect to the amount of banana starch and benzophenone content. The addition of banana starch had no effect on the melting temperature and degree of crystallinity of the films. Similarly, PE‐g‐MA had no effect on the melting temperature but decreased the degree of crystallinity of the LDPE phase. Benzophenone caused an increase in the melting temperature but decreased the degree of crystallinity of LDPE in the films. Increasing the amount of banana starch decreased the tensile properties of the composite films. The addition of PE‐g‐MA as a compatibilizer increased the tensile properties compared with the uncompatibilized films. However, benzophenone had no effect on the tensile properties of the blend films. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2717–2724, 2006     

Effect of blending high‐pressure low‐density polyethylene on the crystallization kinetics of linear low‐density polyethylene

It is well known that the addition of a small amount of high‐pressure low‐density polyethylene (HP‐LDPE) to linear low‐density polyethylene (LLDPE) can improve the optical properties of LLDPE, and LLDPE/HP‐LDPE blend is widely applied to various uses in the field of film. The optical haziness of polyethylene blown films, as a result of surface irregularities, is thought to be as a consequence of the different crystallization mechanisms. However, not much effort has been directed toward understanding the effect of HP‐LDPE blending on the overall crystallization kinetics (k) of LLDPE including nucleation rate (n) and crystal lateral growth rate (v). In this study, we investigated the effect of blending 20% HP‐LDPE on the crystallization kinetics of LLDPE polymerized by Ziegler‐Natta catalyst with comonomer of 1‐butene. Furthermore, by combining depolarized light intensity measurement (DLIM) and small‐angle laser light scattering (SALLS), we have established a methodology to estimate the lateral growth rate at lower crystallization temperatures, in which direct measurement of lateral growth by polarized optical microscopy (POM) is impossible due to the formation of extremely small spherulites. This investigation revealed that HP‐LDPE blending leads to enhanced nucleation rate, reduced crystal lateral growth rate, and a slight increase in the overall crystallization kinetics of pure LLDPE. From the estimated crystal lateral growth rate, it was found that the suppression in v from HP‐LDPE blending is larger at lower temperatures than at higher temperatures. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Thermogravimetric analysis of blends of low‐density polyethylene and poly(dimethyl siloxane) rubber: The effects of compatibilizers

The thermal stability of vulcanizates of low‐density polyethylene (LDPE), poly(dimethyl siloxane) (PDMS) rubber, and their blends was studied by nonisothermal thermogravimetry. Four ethylene copolymers [ethylene methyl acrylate (EMA), ethylene vinyl acetate, ethylene acrylic acid, and a zinc‐salt‐based ionomer (Lotek 4200)] were used as compatibilizers for the blend systems. The thermograms and derivatograms of the blends showed that thermal degradation took place in two stages, whereas those for the base polymers showed single‐stage degradation. Kinetic studies of the blends and pure components showed that the degradation followed first‐order reaction kinetics. The activation energy at 10% degradation was determined with the Freeman–Carroll method and was at a maximum (42.34 kcal/mol) for the 25:75 LDPE/PDMS rubber blend. The half‐life at 200°C was evaluated by the Flynn–Wall method and was at a maximum (812.5 days) for the same blend. Out of four compatibilizers, EMA showed the maximum activation energy (34.25 kcal/mol) for degradation and a maximum half‐life (695.3 days), indicating that EMA was the best compatibilizer for the blend system. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 635–642, 2003     

Thermal and mechanical properties of linear low‐density polyethylene/low‐density polyethylene/wax ternary blends

The thermal and mechanical properties of uncrosslinked three‐component blends of linear low‐density polyethylene (LLDPE), low‐density polyethylene (LDPE), and a hard, paraffinic Fischer–Tropsch wax were investigated. A decrease in the total crystallinity with an increase in both LDPE and wax contents was observed. It was also observed that experimental enthalpy values of LLDPE in the blends were generally higher than the theoretically expected values, whereas in the case of LDPE the theoretically expected values were higher than the experimental values. In the presence of higher wax content there was a good correlation between experimental and theoretically expected enthalpy values. The DSC results showed changes in peak temperature of melting, as well as peak width, with changing blend composition. Most of these changes are explained in terms of the preferred cocrystallization of wax with LLDPE. Young's modulus, yield stress, and stress at break decreased with increasing LDPE content, whereas elongation at yield increased. This is in line with the decreasing crystallinity and increasing amorphous content expected with increasing LDPE content. Deviations from this behavior for samples containing 10% wax and relatively low LDPE contents are explained in terms of lower tie chain fractions. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1748–1755, 2005     

Recycled milk pouch and virgin low‐density polyethylene/linear low‐density polyethylene based coir fiber composites

The viability of the thermomechanical recycling of postconsumer milk pouches [a 50 : 50 low‐density polyethylene/linear low‐density polyethylene (LDPE–LLDPE) blend] and their use as polymeric matrices for coir‐fiber‐reinforced composites were investigated. The mechanical, thermal, morphological, and water absorption properties of recycled milk pouch polymer/coir fiber composites with different treated and untreated fiber contents were evaluated and compared with those of virgin LDPE–LLDPE/coir fiber composites. The water absorption of the composites measured at three different temperatures (25, 45, and 75°C) was found to follow Fickian diffusion. The mechanical properties of the composites significantly deteriorated after water absorption. The recycled polymer/coir fiber composites showed inferior mechanical performances and thermooxidative stability (oxidation induction time and oxidation temperature) in comparison with those observed for virgin polymer/fiber composites. However, a small quantity of a coupling agent (2 wt %) significantly improved all the mechanical, thermal, and moisture‐resistance properties of both types of composites. The overall mechanical performances of the composites containing recycled and virgin polymer matrices were correlated by the phase morphology, as observed with scanning electron microscopy. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Improving low‐density polyethylene/poly(ethylene terephthalate) blends with graft copolymers

Blends of low‐density polyethylene (LDPE) and poly(ethylene terephthalate) (PET) were prepared with different weight compositions with a plasticorder at 240°C at a rotor speed of 64 rpm for 10 min. The physicomechanical properties of the prepared blends were investigated with special reference to the effects of the blend ratio. Graft copolymers, that is, LDPE‐grafted acrylic acid and LDPE‐grafted acrylonitrile, were prepared with γ‐irradiation. The copolymers were melt‐mixed in various contents (i.e., 3, 5, 7, and 9 phr) with a LDPE/PET blend with a weight ratio of 75/25 and used as compatibilizers. The effect of the compatibilizer contents on the physicomechanical properties and equilibrium swelling of the binary blend was investigated. With an increase in the compatibilizer content up to 7 phr, the blend showed an improvement in the physicomechanical properties and reduced equilibrium swelling in comparison with the uncompatibilized one. The addition of a compatibilizer beyond 7 phr did not improve the blend properties any further. The efficiency of the compatibilizers (7 phr) was also evaluated by studies of the phase morphology (scanning electron microscopy) and thermal properties (differential scanning calorimetry and thermogravimetric analysis). © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Degradation of polyethylene during extrusion. II. Degradation of low‐density polyethylene,linear low‐density polyethylene,and high‐density polyethylene in film extrusion

The degradation of different polyethylenes—low‐density polyethylene (LDPE), linear low‐density polyethylene (LLDPE), and high‐density polyethylene (HDPE)—with and without antioxidants and at different oxygen concentrations in the polymer granulates, have been studied in extrusion coating processing. The degradation was followed by online rheometry, size exclusion chromatography, surface oxidation index measurements, and gas chromatography–mass spectrometry. The degradations start in the extruder where primary radicals are formed, which are subject to the auto‐oxidation when oxygen is present. In the extruder, crosslinking or chain scissions reactions are dominating at low and high melt temperatures, respectively, for LDPE, and chain scission is overall dominating for the more linear LLDPE and HDPE resins. Additives such as antioxidants react with primary radicals formed in the melt. Degradation taking place in the film between the die orifice, and the quenching point is mainly related to the exposure time to air oxygen. Melt temperatures above 280°C give a dominating surface oxidation, which increases with the exposure time to air between die orifice and quenching too. A number of degradation products were identified—for example, aldehydes and organic acids—which were present in homologous series. The total amount of aldehydes and acids for each number of chain carbon atoms were appeared in the order of C5>C4>C6>C7?C2 for LDPE, C5>C6>C4>C7?C2 for LLDPE, and C5>C6>C7>C4?C2 for HDPE. The total amounts of oxidized compounds presented in the films were related to the processing conditions. Polymer melts exposed to oxygen at the highest temperatures and longest times showed the presence dialdehydes, in addition to the aldehydes and acids. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1525–1537, 2004     

Multiple shape memory effects of trans‐1,4‐polyisoprene and low‐density polyethylene blends

A novel series of shape memory blends of trans‐1,4‐polyisoprene (TPI) and low‐density polyethylene (LDPE) were prepared using a simple physical blending method. The mechanical, thermal and shape memory properties of the blends were studied and schemes proposed to explain their dual and triple shape memory behaviors. It was found that the microstructures played an important role in the shape memory process. In TPI/LDPE blends, both the TPI crosslinking network and LDPE crystalline regions could work as fixed domains, while crystalline regions of LDPE or TPI could act as reversible domains. The shape memory behaviors were determined by the components of the fixed and reversible domains. When the blend ratio of TPI/LDPE was 50/50, the blends showed excellent dual and triple shape memory properties with both high shape fixity ratio and shape recovery ratio. © 2017 Society of Chemical Industry     

Compatibilizer in waste tire powder and low‐density polyethylene blends and the blends modified asphalt

With the increasing ratio of waste tire powder (WTP) to low‐density polyethylene (LDPE), the hardness and tensile strength of the WTP/LDPE blends decreased while the elongation at break increased. Five kinds of compatibilizers, such as maleic anhydride‐grafted polyethylene (PE‐g‐MA), maleic anhydride‐grafted ethylene‐octene copolymer (POE‐g‐MA), maleic anhydride‐grafted linear LDPE, maleic anhydride‐grafted ethylene vinyl‐acetate copolymer, and maleic anhydride‐grafted styrene‐ethylene‐butylene‐styrene, were incorporated to prepare WTP/LDPE blends, respectively. PE‐g‐MA and POE‐g‐MA reinforced the tensile stress and toughness of the blends. The toughness value of POE‐g‐MA incorporating blends was the highest, reached to 2032.3 MJ/m³, while that of the control was only 1402.9 MJ/m³. Therefore, POE‐g‐MA was selected as asphalt modifier. The toughness value reached to the highest level when the content of POE‐g‐MA was about 8%. Besides that the softening point of the modified asphalt would be higher than 60°C, whereas the content of WTP/LDPE blend was more than 5%, and the blends were mixed by stirring under the shearing speed of 3000 rpm for 20 min. Especially, when the blend content was 8.5%, the softening point arrived at 82°C, contributing to asphalt strength and elastic properties in a wide range of temperature. In addition, the swelling property of POE‐g‐MA/WTP/LDPE blend was better than that of the other compalibitizers, which indicated that POE‐g‐MA /WTP/LDPE blend was much compatible with asphalt. Also, the excellent compatibility would result in the good mechanical and processing properties of the modified asphalt. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Interfacial adhesion evaluation in (low‐density polyethylene)/elastomer blends

Low‐density polyethylene (LDPE) with different elastomers at a ratio of 50/50 wt% blends was prepared by using a co‐rotating twin‐screw extruder. Three kinds of elastomers were used: ground tire rubber (GTR), partially crosslinked butyl rubber (Kalar^®), and styrene‐butadiene‐rubber block copolymer (SBS; Kraton^®). For better characterization of interaction between polyethylene and elastomer, influence of the type of elastomer on the properties of compositions LDPE/elastomer was determined. In the studies, two types of partially crosslinked butyl rubber (differing over filler content and Mooney viscosity) and two types of SBS (differing over structure: linear/branched) were used. The influence of kind and type of elastomer on static mechanical properties (tensile strength, elongation at break, hardness), dynamic mechanical properties, thermal properties, and morphology of obtained compositions were characterized. LDPE/linear SBS copolymer blend had the best mechanical properties, as a result of better compatibility in comparison with other investigated blends. The reason for improved compatibility was an increase of mobility of chain segments in the amorphous phase of polyethylene associated with their partial plasticization by flexible polybutadiene blocks present in SBS copolymer. J. VINYL ADDIT. TECHNOL., 22:492–500, 2016. © 2015 Society of Plastics Engineers     

Blends of low‐density polyethylene and liquid crystalline polymer

Blends of low‐density polyethylene (LDPE) and a glass‐filled thermotropic liquid crystalline polymer (LCP‐g) have been prepared by melt mixing techniques. The thermal transitions, dynamic behavior, morphology and crystalline properties of the blends have been measured by DSC, DMTA, SEM and XRD respectively. The crystallinity decreased with increase in LCP‐g content in the blends. At higher levels of LCP‐g, crystal growth is favored in the PE phase. From DSC, it is found that the thermal stability of the blends increased with the LCP‐g content. The variation of storage modulus, loss modulus and stiffness as a function of blend ratio suggested the phase inversion at the 40–50% level of LCP‐g in the blend. SEM studies revealed that with the increase in LCP‐g content, the flow of the matrix was restricted.     

Rheology of low‐density polyethylene + Boehmite composites

Polyethylene is already one of the most commonly used polymers due to its solvent resistance and easy processing. Low‐density polyethylene (LDPE) also has excellent flexibility and resilience. However, the mechanical properties of LDPE are often poor. We added the inexpensive ceramic filler Boehmite to LDPE, simultaneously improving mechanical properties and reducing production cost—as Boehmite is cheap and abundant while the filler reduces the amount of petroleum‐derived polymer per unit weights of product. Additionally, less environmental contamination results at the end of service life since the Boehmite need not undergo degradation as the LDPE does. To aid adhesion between the matrix and filler, we introduced silane coupling agents (SCAs) to bond the hydrophobic LDPE to the hydrophilic Boehmite. Furthermore, since fillers ordinarily increase viscosity, it was essential to maintain a low viscosity for easy processability. We evaluated by rheometry the effect of the Boehmite on the melt viscosity of the LDPE + Boehmite composites and determined that the addition of any type of Boehmite decreases the viscosity compared to that of neat LDPE. The effects were explained by fiber formation and enhanced rigidity while the allowance for a lower processing temperature results in further energy and therefore cost savings. We also show that high‐temperature exposure of Boehmite during any part of the sample processing results in a decrease in the coupling efficiency of the matrix to filler and in a higher melt viscosity; yet the viscosity is still lower than for neat LDPE. POLYM. COMPOS., 31:1909–1913, 2010. © 2010 Society of Plastics Engineers.     

Processing characteristics of low‐density polyethylene filled with calcium carbonate of different size distributions

Low‐density polyethylene (LDPE) was filled with blends of different proportions of two sizes of calcium carbonate (CaCO₃; 600 and 2500 mesh). The torque of the LDPE/CaCO₃ samples was measured with a torque rheometer. The results showed that the process torque values of the LDPE/CaCO₃ samples obviously decreased when LDPE was filled with a blend of two sizes of CaCO₃ (600‐ and 2500‐mesh CaCO₃ blend) in comparison with samples filled with CaCO₃ of a single size (600 or 2500 mesh). When the ratio of 600‐mesh CaCO₃ to the total CaCO₃ was in the range of 40–60 wt %, the lowest torque value of the LDPE/CaCO₃ samples was achieved. When the content of CaCO₃ in a sample was 30 wt %, LDPE filled with CaCO₃ of different size distributions showed the largest decrease in the torque ratio in comparison with the samples filled with CaCO₃ of a single size. The torques of LDPE samples filled with CaCO₃ of a single size and those filled with CaCO₃ of different size distributions at different temperatures were also studied. The results showed that the flow activation energy and flow activation entropy of LDPE samples filled with CaCO₃ of different size distributions increased obviously. The increase in the flow activation entropy was used to explain the phenomenon of the process torque decreasing for LDPE samples filled with CaCO₃ of different size distributions. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010