Monodisperse‐porous N‐methyl‐D‐glucamine functionalized poly(vinylbenzyl chloride‐co‐divinylbenzene) beads as boron selective sorbent

To generate a new sorbent with high boron adsorption capacity, we synthesized monodisperse‐porous poly(vinylbenzyl chloride‐co‐divinylbenzene), poly(VBC‐co‐DVB), beads 8.5 μm in size by a new “modified seeded polymerization” technique. By using their chloromethyl functionality, the beads were derivatized by a simple, direct reaction with a boron‐selective ligand, N‐methyl‐D ‐glucamine (NMDG). The selection of poly(VBC‐co‐DVB) beads as a starting material allowed to obtain high boron sensitive‐ligand density on the beads depending on their high chloromethyl content. In the batch adsorption runs performed using NMDG‐attached poly(VBC‐co‐DVB) beads as sorbent, boron removal was efficiently performed in a wide pH range between 4 and 11. Quantitative boron removal was observed with the sorbent concentration of 4 g/L. In the same runs, plateau value of equilibrium adsorption isotherm was obtained as 14 mg boron/g beads. Relatively higher boron adsorption was explained by high ligand density and high specific surface area of the sorbent. Boron adsorption isotherms were analyzed using Langmuir and Freundlich models. In the kinetic runs performed for boron removal, the equilibrium was attained within 10 min at a value of 98%. The fast kinetic behavior was explained by the smaller particle size and enhanced porosity of the new sorbent. Infinite solution volume model and unreacted core model were used to evaluate boron adsorption onto the NMDG‐attached poly(VBC‐co‐DVB) beads. The results indicated that the adsorption process is controlled by the particle‐diffusion step. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Characterization of polyacrylonitrile,poly(acrylonitrile‐co‐vinyl acetate), and poly(acrylonitrile‐co‐itaconic acid) based activated carbon nanofibers

In this study, three different acrylonitrile (AN)‐based polymers, including polyacrylonitrile (PAN), poly(acrylonitrile‐co‐vinyl acetate) [P(AN‐co‐VAc)], and poly(acrylonitrile‐co‐itaconic acid) [P(AN‐co‐IA)], were used as precursors to synthesize activated carbon nanofibers (ACNFs). An electrospinning method was used to produce nanofibers. Oxidative stabilization, carbonization, and finally, activation through a specific heating regimen were applied to the electrospun fibers to produce ACNFs. Stabilization, carbonization, and activation were carried out at 230, 600, and 750 °C, respectively. Scanning electron microscopy, thermogravimetric analysis (TGA), and porosimetry were used to characterize the fibers in each step. According to the fiber diameter variation measurements, the pore extension procedure overcame the shrinkage of the fibers with copolymer precursors. However, the shrinkage process dominated the scene for the PAN homopolymer, and this led to an increase in the fiber diameter. The 328 m²/g Brunauer–Emmett–Teller surface area for ACNFs with PAN precursor were augmented to 614 and 564 m²/g for P(AN‐co‐VAc) and P(AN‐co‐IA), respectively. The TGA results show that the P(AN‐co‐IA)‐based ACNFs exhibited a higher thermal durability in comparison to the fibers of PAN and P(AN‐co‐VAc). The application of these copolymers instead of AN homopolymer enhanced the thermal stability and increased the surface area of the ACNFs even in low‐temperature carbonization and activation processes. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44381.     

Enhancement of the high‐temperature utility of a polystyrene‐b‐poly(ethylene‐co‐butylene)‐b‐polystyrene block copolymer by friedel–crafts naphthoylation

A procedure was developed for the Friedel–Crafts naphthoylation of the polystyrene segments of a polystyrene‐b‐poly(ethylene‐co‐butene)‐b‐polystyrene (SEBS) triblock copolymer. It was possible to obtain up to 72% 1‐naphthoylation or 100% 2‐naphthoylation of the polystyrene segments in the copolymer. Naphthoylation could also be accomplished using trifluoromethanesulfonic acid as a catalyst. The naphthoylated products were characterized by ¹H‐NMR spectroscopy, size‐exclusion chromatography, and dynamic mechanical thermal analysis. The mechanical properties of the original and naphthoylated polymers were measured from 25 to 125°C. The results obtained indicate that naphthoylation enhances the tensile properties of the polymers at elevated temperatures. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1289–1295, 2003     

Synthesis and properties of poly(acrylonitrile‐co‐p‐trimethylsilylstyrene) and poly(acrylonitrile‐co‐p‐trimethylsilylstyrene‐co‐styrene)

Copolymerization of acrylonitrile (AN) with p‐trimethylsilylstyrene (TMSS) was carried out at 60°C in bulk and in solution in the presence of 2,2′‐azobisisobutyronitrile (AIBN). The reactivity ratios of AN (M₁) and TMSS (M₂) were determined to be r₁ = 0.068 and r₂ = 0.309. The effects of the AIBN concentration and that of the chain transfer agent CCl₄ on the molecular weights (MWs) of the copolymers were investigated. An increase in the concentrations of AIBN or CCl₄ in solution led to a decrease in MW. Poly(AN‐co‐TMSS‐co‐St) was synthesized in solution using AIBN as the initiator. The molar fraction of AN was 0.415, while the molar ratio of TMSS/St varied from 1 : 1 to 1 : 9. The transition temperatures and thermal and thermooxidative stabilities of poly(AN‐co‐TMSS) and poly(AN‐co‐TMSS‐co‐St) were investigated. The differential scanning calorimeter technique was used to determine the compatibility of the poly(AN‐co‐TMSS) and poly(AN‐co‐TMSS‐co‐St) with commercial poly(AN‐co‐St). All the blends show a single glass transition temperature, which indicates the compatibility of the blend components. The surface film morphology of the blends mentioned above was examined by X‐ray photoelectron spectroscopy. The data obtained indicate that the silicon‐containing copolymer is concentrated in the surface layer. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1920–1928, 2000     

Hypercrosslinked silole‐containing microporous organic polymers with N‐functionalized pore surfaces for gas storage and separation

Novel hypercrosslinked microporous organic polymers (MOPs) derived from N‐functionalized siloles as basic building units have been designed and synthesized via Friedel–Crafts alkylation reaction. The resulting N‐functional silole‐containing polymer networks exhibit high thermal stabilities and moderate Brunauer–Emmett–Teller surface area ranging from 666 to 1137 m² g^?1. The incorporation of carbazole or triphenylamine moieties into the polymer skeleton increases the number of electron donating basic nitrogen sites in the porous frameworks. Thus, the corresponding polymer PDMCzS shows enhanced CO₂ adsorption capacities of 3.23 mmol g^?1 at 273 K and 1.13 bar, and higher CO₂/N₂ selectivity (43.99) at 273 K than the analogous silole‐containing polymers P1–P3. These results demonstrated that the N‐functionalized silole‐containing polymer network is a very promising candidate for potential applications in post‐combustion CO₂ capture and sequestration. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45907.     

Influences of co‐monomers and electrolyte acidity on morphological structure of copper‐in‐copolymer gradient film

In this paper, the influences of composition of copolymers and acidity of electrolyte in an electrochemical reactor on morphological structure of copper‐in‐polymer gradient composite film were investigated. For binary copolymers, poly(acrylonitrile‐co‐methyl acrylate) [P(AN‐co‐MA)] and poly(acrylonitrile‐co‐sodium allyl sulfonate) [P(AN‐co‐SAS)], the charged group ? SO in P(AN‐co‐SAS) improves the swelling of the copolymer phase and copper reduction to form gradient morphology; the carboxylic ester group in P(AN‐co‐MA) is not effective because of its poor hydrophilicity, but it is a cooperating component with P(AN‐co‐SAS) to avoid excess of counterion (i.e., Na⁺) in SCF, which might severely interrupt Cu²⁺ coexistence. The swelling of the polymer phase is helpful to decrease the energy of the transfer ions in SCF and to enhance copper deposition and gradient formation. The increase of surface energy because of cluster growth raises the surface energy level of deposited Cu⁰ clusters. The conteraction between these two energy factors allows the size of clusters to be 50–100 nm. The appropriate H⁺ concentration improves active Cu²⁺ reduction and thus deposited gradient copper phase in the copolymer matrix. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 373–380, 2004     

Preparation of bi‐continuous poly(acrylonitrile‐co‐methyl acrylate) microporous membranes by a thermally induced phase separation method

Poly(acrylonitrile‐co‐methyl acrylate) [P(AN‐MA)] flat microfiltration membranes were successfully prepared via the thermally induced phase separation (TIPS) method, by using low polar caprolactam (CPL) and methoxypolyethylene glycol 550 (MPEG 550) as the mixed diluent. In this work, P(AN‐MA) membranes exhibit bi‐continuous networks, porous surfaces, high porosity, and big pore size, when membrane fabricated from a high MPEG 550 content, low P(AN‐MA) concentration, and small cooling rate, it can be dry state preservation and do not need to be impregnated by any solvent. When the ternary system was composed of 15 wt % P(AN‐MA), 12.5 wt % CPL, and 87.5 wt % MPEG 550, formed at 25 °C air bath, membrane has the highest water flux of 4420 L m^?2 h^?1. The obtained P(AN‐AN) membrane displays a high carbonic black ink rejection ranging from 83.7 to 98.5 wt %. Moreover, P(AN‐MA) polymer not only retains the advantages of PAN but also reduces the polar component from 16.2 to 10.77 MPa^0.5. It can be used membrane matrix to obtain pore structure and excellent mechanical property membrane via TIPS. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46173.     

Synthesis and characterization of novel swelling tunable oligomeric poly(styrene‐co‐acrylamide) modified clays

The oligomeric poly(styrene‐acrylamide‐vinylbenzylchloride) (P(St‐AM‐VBC)) quaternary ammonium salts have been prepared from the reactions of trimethylamine with the corresponding P(St‐AM‐VBC)s, which were synthesized by free‐radical polymerization of a mixture of styrene, acrylamide, and vinylbenzylchloride. Then the swelling tunable oligomeric poly(styrene‐co‐acrylamide) modified clays have been prepared through cation exchange of the sodium ions in the clay with the corresponding P(St‐AM‐VBC) quaternary ammonium salts. The P(St‐AM‐VBC) and its modified clays have been characterized by infrared spectra (IR), gel permeation chromatography (GPC), thermogravimetric analysis (TGA), proton nuclear magnetic resonance (¹H NMR), X‐ray diffraction (XRD), and transmission electron microscopy (TEM). The solvent‐swelling capacity of poly(styrene‐co‐acrylamide) modified clays have also been tested, and the experimental results have indicated that these clays are novel swelling tunable organic clays. XRD and TEM studies have shown that these novel swelling tunable clays are well‐intercalated or exfoliated. Furthermore, TGA analysis shows that these polymerically modified clays have high thermal stability for nanocomposites by melt blending. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Hypercross‐Linked Fiber and its Adsorption of Cyclohexane Vapor

A novel hypercross‐linked fiber which has an excellent adsorption capacity for cyclohexane vapor was prepared by cross‐linking PP‐ST‐DVB fibers with p‐xylylenedichloride according to the Friedel‐Crafts reaction. The effects of several important factors on the Friedel‐Crafts reaction, including reaction temperature, reaction time, catalyst type, and material ratio were investigated in detail and the optimal synthesis conditions of hypercross‐linked fiber were obtained. The adsorption equilibrium for cyclohexane vapor on hypercross‐linked fiber was measured by a static volumetric technique. The equilibrium measurements were performed at 298, 323 and 348 K and pressures of up to 6.04 kPa. The results can be well fitted by the Freundlich model. The isosteric heat curve was derived from the equilibrium data, and indicates that the hypercross‐linked fiber has an energetically heterogeneous surface.     

Preparation of poly(divinylbenzene‐co‐N‐isopropylacrylamide) microspheres and their hydrogen‐bonding assembly behavior for raspberry‐like core‐corona polymer composite

Narrowdisperse poly(divinylbenzene‐co‐N‐isopropylacrylamide) (poly(DVB‐co‐NIPAM)) functional microspheres with the diameter in the range of 630 nm and 2.58 μm were prepared by distillation–precipitation polymerization in neat acetonitrile in the absence of any stabilizer. The effect of N‐isopropylacrylamide (NIPAM) ratio in the comonomer feed on the morphology of the resultant polymer particles was investigated in detail with divinylbenzene (DVB) as crosslinker and 2,2′‐azobisisobutyronitrile (AIBN) as initiator. The monodisperse poly(DVB‐co‐NIPAM) microspheres with NIPAM fraction of 20 wt % were selected for the preparation of raspberry‐like core‐corona polymer composite by the hydrogen‐bonding self‐assembly heterocoagulation with poly(ethyleneglycol dimethacrylate‐co‐acrylic acid) [poly(EGDMA‐co‐AA)] nanospheres. Both of the functional poly(DVB‐co‐NIPAM) microspheres and the core‐corona particles were characterized with scanning electron microscopy (SEM), Fourier transform infrared spectra (FTIR), and elemental analysis (EA). © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1350–1357, 2007     

Simultaneous radiation grafting of vinylbenzyl chloride onto poly(tetrafluoroethylene‐co‐hexafluoropropylene) films

In this study, we demonstrated that vinylbenzyl chloride (VBC), a versatile monomer with reactive a chloromethyl group could be grafted onto a poly(tetrafluoroethylene‐co‐hexafluoropropylene) (FEP) film without a degradation of the chloromethyl group during a simultaneous irradiation process. The effects of various irradiation conditions such as the total dose, dose rate, solvent, and VBC concentration on the degree of grafting of VBC onto a FEP film were also investigated. The prepared PVBC‐grafted films were characterized using FTIR, TGA, and SEM EDX. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

A new approach to the preparation of large surface area poly(styrene-co-divinylbenzene) monoliths via knitting of loose chains using external crosslinkers and application of these monolithic columns for separation of small molecules

Poly(styrene-divinylbenzene) monoliths have been hypercrosslinked using a Fe³⁺ catalyzed Friedel–Crafts reaction involving three external crosslinkers (1) 4,4′-bis(chloromethyl)-1,1′-biphenyl, (2) α,α′-dichloro-p-xylene, and (3) formaldehyde dimethyl acetal. The first crosslinker was found to produce monoliths with the best chromatographic performance. The effects of a number of variables affecting the hypercrosslinking reaction were studied in detail. These variables included: (i) the temperature and time used for polymerization of the precursor monoliths, (ii) the amount and loading procedure of the external crosslinker and catalyst, and, (iii) the temperature and reaction time of the Friedel–Crafts alkylation. Polymers with extremely large surface areas reaching up to 900 m²/g were obtained using a precursor monolith polymerized for only 2.5 h, and hypercrosslinked with 4,4’-bis(chloromethyl)-1,1′-biphenyl. The increased performance of monoliths modified using this new procedure is comparable to the performance obtained with monolithic polymers containing chloromethylstyrene. However, the preparation of the poly(styrene-divinylbenzene) precursor is simpler than that of conterparts containing chloromethylstyrene. The hypercrosslinked monoliths in capillary columns were tested in an isocratic reversed phase liquid chromatography separation using a mixture comprised of acetone and six alkylbenzenes. Column efficiencies for retained analytes exceeded 70,000 plates/m.     

Lewis acid–base property of P(VDF‐co‐HFP) measured by inverse gas chromatography

Poly (vinylidene fluoride‐co‐hexafluoropropylene) P(VDF‐co‐HFP) is an excellent material for polymer electrolytes of lithium ion battery. To enhance the lithium ion transference number, some metal oxides were often embedded into P(VDF‐co‐HFP). The promising mechanism for the increase in lithium ionic conductivity was Lewis acid‐base theory. In this experiment, the Lewis acid–base properties of P(VDF‐co‐HFP) were measured by inverse gas chromatography (IGC). The Lewis acid constant K_a of P(VDF‐co‐HFP) is 0.254, and the base constant K_b is 1.199. Compared with other polymers characterized by IGC, P(VDF‐co‐HFP) is the strongest Lewis basic polymers. Except aluminum ion, lithium ion is the strongest Lewis acidic ion according to their η value of Lewis acids. Therefore, a strong Lewis acid–base interaction will exist between lithium ion and P(VDF‐co‐HFP). This will restrict the transference of lithium ion in P(VDF‐co‐HFP). To enhance the lithium ion transference by blending other metal ions into P(VDF‐co‐HFP), it is suggested that the preferential ions should be Al³⁺, Mg²⁺, Na⁺, and Ca²⁺ because these metal ions have relative large η values. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Free‐standing hybrid anion‐exchange membranes for application in fuel cells

A series of free‐standing hybrid anion‐exchange membranes were prepared by blending brominated poly(2,6‐dimethyl‐1,4‐phenylene oxide) (BPPO) with poly(vinylbenzyl chloride‐co‐γ‐methacryloxypropyl trimethoxy silane) (poly(VBC‐co‐γ‐MPS)). Apart from a good compatibility between organic and inorganic phases, the hybrid membranes had a water uptake of 32.4–51.8%, tensile strength around 30 MPa, and T_d temperature at 5% weight loss around 243–261°C. As compared with the membrane prepared from poly (VBC‐co‐γ‐MPS), the hybrid membranes exhibited much better flexibility, and larger ion‐exchange capacity (2.19–2.27 mmol g^?1) and hydroxyl (OH^?) conductivity (0.0067–0.012 S cm^?1). In particular, the hybrid membranes with 60–75 wt % BPPO had the optimum water uptake, miscibility between components, and OH^? conductivity, and were promising for application in fuel cells. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and characterization of N‐ and O‐alkylated poly[aniline‐co‐N‐(2‐hydroxyethyl) aniline]

Poly[aniline‐co‐N‐(2‐hydroxyethyl) aniline] was synthesized in an aqueous hydrochloric acid medium with a determined feed ratio by chemical oxidative polymerization. This polymer was used as a functional conducting polymer intermediate because of its side‐group reactivity. To synthesize the alkyl‐substituted copolymer, the initial copolymer was reacted with NaH to obtain the N‐ and O‐anionic copolymer after the reaction with octadecyl bromide to prepare the octadecyl‐substituted polymer. The microstructure of the obtained polymers was characterized by Fourier transform infrared spectroscopy, ¹H‐NMR, and X‐ray diffraction. The thermal behavior of the polymers was investigated by thermogravimetric analysis and differential scanning calorimetry. The morphology of obtained copolymers was studied by scanning electron microscopy. The cyclic voltammetry investigation showed the electroactivity of poly [aniline‐co‐N‐(2‐hydroxyethyl) aniline] and N and O‐alkylated poly[aniline‐co‐N‐(2‐hydroxyethyl) aniline]. The conductivities of the polymers were 5 × 10^?5 S/cm for poly[aniline‐co‐N‐(2‐hydroxyethyl) aniline] and 5 ×10^?7 S/cm for the octadecyl‐substituted copolymer. The conductivity measurements were performed with a four‐point probe method. The solubility of the initial copolymer in common organic solvents such as N‐methyl‐2‐pyrrolidone and dimethylformamide was greater than polyaniline. The alkylated copolymer was mainly soluble in nonpolar solvents such as n‐hexane and cyclohexane. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and antitumor activity of poly(3,4‐dihydro‐2H‐pyran‐co‐maleic anhydride‐co‐vinyl acetate)

The radical‐initiated terpolymerization of 3,4‐dihydro‐2H‐pyran (DHP), maleic anhydride (MA), and vinyl acetate (VA), which were used as a donor–acceptor–donor system, was carried out in methyl ethyl ketone in the presence of 2,2′‐azobisisobutyronitrile as an initiator at 65°C in a nitrogen atmosphere. The synthesis and characterization of binary and ternary copolymers, some kinetic parameters of terpolymerization, the terpolymer‐composition/thermal‐behavior relationship, and the antitumor activity of the synthesized polymers were examined. The polymerization of the DHP–MA–VA monomer system predominantly proceeded by the alternating terpolymerization mechanism. The in vitro cytotoxicities of poly(3,4‐dihydro‐2H‐pyran‐alt‐maleic anhydride) [poly(DHP‐alt‐MA)] and poly(3,4‐dihydro‐2H‐pyran‐co‐maleic anhydride‐co‐vinyl acetate) [poly(DHP‐co‐MA‐co‐VA)] were evaluated with Raji cells (human Burkitt lymphoma cell line). The antitumor activity of the prepared anion‐active poly(DHP‐alt‐MA) and poly(DHP‐co‐MA‐co‐VA) polymers were studied with methyl–thiazol–tetrazolium testing, and the 50% cytotoxic dose was calculated. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2352–2359, 2005     

Copolyesters of hydroxyphenylalkanoic acids: synthesis and thermal properties of poly{(4‐oxybenzoate)‐co‐[8‐(3‐oxyphenyl)octanoate]} and poly{(3‐bromo‐4‐oxybenzoate)‐co‐[8‐(3‐oxyphenyl)octanoate]}

Copolyesters of 8‐(3‐hydroxyphenyl)octanoic acid (HPOA), a monomer with kink and flexible segment derived from cardanol, and 4‐hydroxybenzoic acid (HBA) or its brominated derivative, 3‐bromo‐4‐hydroxybenzoic acid (BrHBA), were synthesized by acidolysis melt polycondensation of the in situ generated acetoxyderivative in the presence of magnesium acetate as catalyst by a one‐pot method and characterized. The formation of the copolyester was confirmed by elemental analysis, FTIR and ¹H NMR spectroscopy. These polymers were highly insoluble in most solvents except highly polar solvents, such as trifluoroacetic acid. The inherent viscosities of the soluble polymers were in the range of 0.8–1.1 dlg^?1. The thermal and phase behaviour of the copolyesters were studied by DSC and polarized light microscopy. Poly{(4‐oxybenzoate)‐co‐[8‐(3‐oxyphenyl)octanoate]} with 50 mole% of HPOA showed a birefringent melt with opalescence and a worm‐like texture of a nematic phase. The effect of bromine substitution in the analogue poly{(3‐bromo‐4‐oxybenzoate)‐co‐[8‐(3‐oxyphenyl)octanoate]} was evident when it showed a lower transition with minimum 45% Br‐HBA at 225 °C showing enhanced melt processability. These copolymers, with hydrolytically degradable aliphatic carbonyl group and better crystallinity compared to poly(hydroxyalkanoate)s, are interesting in possible biomedical applications. © 2002 Society of Chemical Industry     

Synthesis,characterization, and comparison of self‐doped,doped, and undoped forms of polyaniline,poly(o‐anisidine), and poly[aniline‐co‐(o‐anisidine)]

Polyaniline (PANI), poly(o‐anisidine), and poly[aniline‐co‐(o‐anisidine)] were synthesized by chemical oxidative polymerization with ammonium persulfate as an oxidizing reagent in an HCl medium. The viscosities, electrical conductivity, and crystallinity of the resulting polymers (self‐doped forms) were compared with those of the doped and undoped forms. The self‐doped, doped, and undoped forms of these polymers were characterized with infrared spectroscopy, ultraviolet–visible spectroscopy, and a four‐point‐probe conductivity method. X‐ray diffraction characterization revealed the crystalline nature of the polymers. The observed decrease in the conductivity of the copolymer and poly(o‐anisidine) with respect to PANI was attributed to the incorporation of the methoxy moieties into the PANI chain. The homopolymers attained conductivity in the range of 3.97 × 10^?3 to 7.8 S/cm after doping with HCl. The conductivity of the undoped forms of the poly[aniline‐co‐(o‐anisidine)] and poly(o‐anisidine) was observed to be lower than 10^?5 J/S cm^?1. The conductivity of the studied polymer forms decreased by the doping process in the following order: self‐doped → doped → undoped. The conductivity of the studied polymers decreased by the monomer species in the following order: PANI → poly[aniline‐co‐(o‐anisidine)] → poly(o‐anisidine). All the polymer samples were largely amorphous, but with the attachment of the pendant groups of anisidine to the polymer system, the crystallinity region increased. The undoped form of poly[aniline‐co‐(o‐anisidine)] had good solubility in common organic solvents, whereas doped poly[aniline‐co‐(o‐anisidine)] was moderately crystalline and exhibited higher conductivity than the anisidine homopolymer. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Multilayer composite surfaces prepared by an electrostatic self‐assembly technique with quaternary ammonium salt and poly(acrylic acid) on poly(acrylonitrile‐co‐acrylic acid) membranes

An electrostatic self‐assembly technique was applied to prepare ion complex polymer layers on polyacrylonitrile with acrylic acid segments {poly(acrylonitrile‐co‐acrylic acid) [P(AN‐co‐AA)]}. For the ionic complex layers, quaternary ammonium salts, such as cetyl trimethyl ammonium chloride (CTAC) and tetramethyl ammonium chloride (TMAC), were used as cationic species, and also, poly(acrylic acid) (PAA) was used as an anionic species. These cationic and anionic species were self‐assembled alternately on the surface of the P(AN‐co‐AA) membrane. Fourier transform infrared spectroscopy, AFM, and water contact angle measurements of the membrane surface were used to confirm the formation of the multilayer composites on the P(AN‐co‐AA). The permeabilities of water and macromolecules of different molecular weights were evaluated by a membrane filtration technique. The values of permeability strongly depended on the formation layer by layer of these ion composites on the base P(AN‐co‐AA). Through the measurement of the values of the contact angle of water, it was clear that surface nature of the base membrane treated by CTAC or TMAC and PAA dramatically changed. We concluded that such an electrostatic self‐assembly technique is useful for the preparation of multicomposite layers to modify the surface of base P(AN‐co‐AA) membranes. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008