Behavior of the monophosphate tungsten bronzes (PO2)4(WO3)2m (m = 7 and 8) in the course of electrochemical lithium insertion

The electrochemical lithium insertion process has been studied in the family of monophosphate tungsten bronzes (PO₂)₄(WO₃)_2m, where m = 7 and 8. Structural changes in the pristine oxides were followed as lithium insertion proceeded. Through potentiostatic intermittent technique the different processes which take place in the cathode during the discharge of the cell were analyzed. The nature of the bronzes Li_x(PO₂)₄(WO₃)_2m formed was determined by in situ X-ray diffraction experiments. These results have allowed establishing a correlation with the reversible/irreversible processes detected during the electrochemical lithium insertion.     

MnO2 cathode in an aqueous Li2SO4 solution for battery applications

A manganese dioxide (MnO₂) cathode with zinc (Zn) as the anode has been investigated using lithium sulphate (Li₂SO₄) as an electrolyte. Previously we demonstrated that cells comprising MnO₂ and lithium hydroxide (LiOH) as an electrolyte can be made rechargeable to over one-electron capacity with a discharge capacity of 150 mAh g⁻¹. Here we have extended our work to assess Li₂SO₄ as an electrolyte and have found that the battery is not rechargeable. Based on the electrochemical (discharge/charge) performance and the products formed following discharge and charge, the mechanism proposed for the sulphate-based media is one of proton insertion into the MnO₂ cathode, rather than the lithium ion insertion observed for the LiOH electrolyte. The addition of bismuth species to the Li₂SO₄-based cell results in a transition to rechargeable behaviour. This is believed to be due to the influence of Bi ions on the formation of soluble Mn³⁺ soluble intermediates. However, the coulombic efficiency of the cell diminishes rapidly with repeated charge/discharge cycles. This confirms that the nature of the Li-containing electrolyte has a marked influence on the electrochemistry of the cell.     

Unique CNTs-chained Li4Ti5O12 nanoparticles as excellent high rate anode materials for Li-ion capacitors

Composite anode materials with a unique architecture of carbon nanotubes (CNTs)-chained spinel lithium titanate (Li₄Ti₅O₁₂, LTO) nanoparticles are prepared for lithium ion capacitors (LICs). The CNTs networks derived from commercial conductive slurry not only bring out a steric hindrance effect to restrict the growth of Li₄Ti₅O₁₂ particles but greatly enhance the electronic conductivity of the CNTs/LTO composites, both have contributed to the excellent rate capability and cycle stability. The capacity retention at 30 C (1 C = 175 mA g^?1) is as high as 89.7% of that at 0.2 C with a CNTs content of 11 wt%. Meanwhile, there is not any capacity degradation after 500 cycles at 5 C. The LIC assembled with activated carbon (AC) cathode and such a CNTs/LTO composite anode displays excellent energy storage properties, including a high energy density of 35 Wh kg^?1 at 7434 W kg^?1, and a high capacity retention of 87.8% after 2200 cycles at 1 A g^?1. These electrochemical performances outperform the reported data achieved on other LTO anode-based LICs. Considering the facile and scalable preparation process proposed herein, the CNTs/LTO composites can be very potential anode materials for hybrid capacitors towards high power-energy outputs.     

Hydrothermal synthesis of Co3O4 microspheres as anode material for lithium-ion batteries

Co₃O₄ microspheres were synthesized in mass production by a simple hydrothermal treatment. One micrometer-sized spherical particles with well-crystallization could be obtained by XRD and SEM. Higher specific surface area (93.4 m² g⁻¹) and larger pore volume (78.4 cm³ g⁻¹) by BET measurements offered more interfacial bondings for extra sites of Li⁺ insertion, which resulted in the anomalous large initial irreversible capacity and capacity cycling loss due to SEI film formation. The capacity retention of Co₃O₄ microspheres involved first forming acted as Li-ion anode material is almost above 90% from 12th cycle and it retain lithium storage capacity of 550.2 mAh g⁻¹ after 25 cycles, which show good long-life stability. The electrochemical impedance spectroscopy (EIS) tests before and after cyclic voltammetry measurements and charge-discharge experiments were carried out and the corresponding D_Li values were also calculated. The relationship of the ac impedance spectra and the cycling behaviors was discussed. It is found that the decrease of capacity results from the larger Li⁺ charge-transfer impedance and the lower lithium-diffusion processes on cycling, which is in very good agreement with the electrochemical behaviors of Co₃O₄ electrode.     

Electrochemical lithium insertion in (PO2)4(WO3)2m (2 ≤ m ≤ 10): Relation among the electrochemical insertion process and structural features

In this work it is presented a review of the main results obtained during the electrochemical lithium insertion in the family of monophosphate tungsten bronzes (PO₂)₄(WO₃)_2m (2 ≤ m ≤ 10). This family of oxides is a good system in order to study the relation among the electrochemical processes observed in the course of lithium insertion and the changes of bronzes structures. By means of X-ray diffraction experiments, the nature of Li_x(PO₂)₄(WO₃)_2m phases has been elucidated and a correlation with the reversible/irreversible processes observed during the electrochemical insertion has been established. The electrical properties of the inserted Li_x(PO₂)₄(WO₃)_2m phases were measured and a relation with the amount of lithium inserted and m was also found.     

All solid-state lithium polymer secondary batteries using spinel Li4/3Ti5/3O4 as an active material

Present paper describes electrochemical performance of the all solid-state lithium polymer battery (LBP) using spinel-type Li_4/3Ti_5/3O₄ which has been known as the potential candidate of anode materials.The assembled LPB with Li|solid polymer electrolyte(SPE)|Li_4/3Ti_5/3O₄ construction showed stable charge-discharge cycles more than 300 times at 1 C condition. On the other hand, strong charge-discharge rate dependence for the specific capacity and initial capacity loss was indicated. Such a poor rate performance stemmed from low diffusivity of Li⁺ ion in the by-products produced by the decomposition of SPE components at the SPE|Li_4/3Ti_5/3O₄ interface.     

Improvement of cycle performance of lithium ion cell LiMn2O4/LixV2O5 with aqueous solution electrolyte by polypyrrole coating on anode

The reasons of capacity fading during cycling process of LiMn₂O₄/Li_xV₂O₅ lithium ion cell with 5 M LiNO₃ aqueous solution as electrolyte were investigated. XRD and ICP results showed that the properties of the anode have more impact on the cycle life of the cell. In an attempt to improve the cycle performance of the as-assembled cell, coating with an ionic conductive polypyrrole (PPy) on the surface of the anode was proposed via in situ polymerization method. Cycling tests revealed that the stability of the lithium ion cell with surface coated anode has been greatly improved. Moreover, the capability of the cell with coated anode was also enhanced compared with the cell with bare anode.     

Improved electrochemical properties of Li1+x(Ni0.3Co0.4Mn0.3)O2−δ (x = 0, 0.03 and 0.06) with lithium excess composition prepared by a spray drying method

Layered Li_1+x(Ni_0.3Co_0.4Mn_0.3)O_2−δ (x = 0, 0.03 and 0.06) materials were synthesized through the different calcination times using the spray-dried precursor with the molar ratio of Li/Me = 1.25 (Me = transition metals). The physical and electrochemical properties of the lithium excess and the stoichiometric materials were examined using XRD, AAS, BET and galvanostatic electrochemical method. As results, the lithium excess Li_1.06(Ni_0.3Co_0.4Mn_0.3)O_2−δ could show better electrochemical properties, such as discharge capacity, capacity retention and C rate ability, than those of the stoichiometric Li_1.00(Ni_0.3Co_0.4Mn_0.3)O_2−δ. In this paper, the effect of excess lithium on the electrochemical properties of Li_1+x(Ni_0.3Co_0.4Mn_0.3)O_2−δ materials will be discussed based on the experimental results of ex situ X-ray diffraction, transmission electron microscopy (TEM) and galvanostatic intermittent titration technique (GITT)     

Synthesis of LiFePO4/C cathode material from ferric oxide and organic lithium salts

LiFePO₄/C cathode material has been simply synthesized via a modified in situ solid-state reaction route using the raw materials of Fe₂O₃, NH₄H₂PO₄, Li₂C₂O₄ and lithium polyacrylate (PAALi). The sintering temperature of LiFePO₄/C precursor is studied by thermo-gravimetric (TG)/differential thermal analysis (DTA). The physical properties of LiFePO₄/C are then investigated through analysis using by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscope (TEM) and the electrochemical properties are investigated by electrochemical impedance spectra (EIS), cyclic voltammogram (CV) and constant current charge/discharge test. The LiFePO₄/C composite with the particle size of ∼200 nm shows better discharge capacity (156.4 mAh g⁻¹) than bare LiFePO₄ (52.3 mAh g⁻¹) at 0.2 C due to the improved electronic conductivity which is demonstrated by EIS. The as-prepared LiFePO₄/C through this method also shows excellent high-rate characteristic and cycle performance. The initial discharge capacity of the sample is 120.5 mAh g⁻¹ and the capacity retention rate is 100.6% after 50 cycles at 5 C rate. The results prove that the using of organic lithium salts can obtain a high performance LiFePO₄/C composite.     

Layered lithium transition metal nitrides as novel anodes for lithium secondary batteries

We report the approach to overcome the deterrents of the hexagonal Li_2.6Co_0.4N as potential insertion anode for lithium ion batteries: the rapid capacity fading upon long cycles and the fully Li-rich state before cycling. Research reveals that the appropriate amount of Co substituted by Cu can greatly improve the cycling performance of Li_2.6Co_0.4N. It is attributed to the enhanced electrochemical stability and interfacial comparability. However, doped Cu leads to a slightly decreased capacity. High energy mechanical milling (HEMM) was found to effectively improve the reversible capacity associated with the electrochemical kinetics by modifying the active hosts’ morphology characteristics. Moreover, the composite based on mesocarbon microbead (MCMB) and Li_2.6Co_0.4N was developed under HEMM. The composite demonstrates a high first cycle efficiency at 100% and a large reversible capacity of ca. 450 mAh g⁻¹, as well as a stable cycling performance. This work may contribute to a development of the lithium transition metal nitrides as novel anodes for lithium ion batteries.     

The influence of carbon content on the lithium diffusion and electrochemical properties of lithium vanadium phosphate

The influence of carbon content and porosity of lithium vanadium phosphate, Li₃V₂(PO₄)₃, on its diffusion properties and electrochemical performance was examined by GITT and galvanostatic charge/discharge experiments. The diffusion coefficient of Li₃V₂(PO₄)₃, as determined by GITT measurements, appears relatively high, thus making this material interesting also for high power application. Moreover, the results of this study clearly show that the porosity and the carbon content of the electrode materials is an important factor affecting the diffusion as well as the electrochemical performance of Li₃V₂(PO₄)₃. It was demonstrated that excessive carbon coating may lead to kinetic hindrances but may also contribute specific capacity in anode materials in voltage regions below 1.0 V versus Li/Li⁺.     

Preparation and evaluation of α-Al2O3 supported lithium ion sieve membranes for Li+ extraction

Spinel lithium manganese oxide ion-sieves have been considered the most promising adsorbents to extract Li⁺ from brines and sea water. Here, we report a lithium ion-sieve which was successfully loaded onto tubular α-Al₂O₃ ceramic substrates by dipping crystallization and post-calcination method. The lithium manganese oxide Li₄Mn₅O₁₂ was first synthesized onto tubular α-Al₂O₃ ceramic substrates as the ion-sieve precursor (i.e. L-AA), and the corresponding lithium ion-sieve (i.e. H-AA) was obtained after acid pickling. The chemical and morphological properties of the ion-sieve were confirmed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Both L-AA and H-AA showed characteristic peaks of α-Al₂O₃ and cubic phase Li₄Mn₅O₁₂, and the peaks representing cubic phase could still exist after pickling. The lithium manganese oxide Li₄Mn₅O₁₂ could be uniformly loaded not only on the surface of α-Al₂O₃ substrates but also inside the pores. Moreover, we found that the equilibrium adsorption capacity of H-AA was 22.9 mg·g⁻¹. After 12 h adsorption, the adsorption balance was reached. After 5 cycles of adsorption, the adsorption capacity of H-AA was 60.88% of the initial adsorption capacity. The process of H-AA adsorption for Li⁺ correlated with pseudo-second order kinetic model and Langmuir model. Adsorption thermodynamic parameters regarding enthalpy (∆ H), Gibbs free energy (∆ G) and entropy (∆ S) were calculated. For the dynamic adsorption–desorption process of H-AA, the H-AA exhibited excellent adsorption performance to Li⁺ with the Li⁺ dynamic adsorption capacity of 9.74 mg·g⁻¹ and the Mn²⁺ dissolution loss rate of 0.99%. After 3 dynamic adsorption–desorption cycles, 80% of the initial dynamic adsorption capacity was still kept.     

Synthesis and characterization of carbon-coated Li3V2(PO4)3 cathode materials with different carbon sources

The carbon-coated monoclinic Li₃V₂(PO₄)₃ (LVP) cathode materials were synthesized by a solid-state reaction process under the same conditions using citric acid, glucose, PVDF and starch, respectively, as both reduction agents and carbon coating sources. The carbon coating can enhance the conductivity of the composite materials and hinder the growth of Li₃V₂(PO₄)₃ particles. Their structures and physicochemical properties were investigated using X-ray diffraction (XRD), thermogravimetric (TG), scanning electron microscopy (SEM) and electrochemical methods. In the voltage region of 3.0-4.3 V, the electrochemical cycling of these LVP/C electrodes all presents good rate capability and excellent cycle stability. It is found that the citric acid-derived LVP owns the largest reversible capacity of 118 mAh g⁻¹ with no capacity fading during 100 cycles at the rate of 0.2C, and the PVDF-derived LVP possesses a capacity of 95 mAh g⁻¹ even at the rate of 5C. While in the voltage region of 3.0-4.8 V, all samples exhibit a slightly poorer cycle performance with the capacity retention of about 86% after 50 cycles at the rate of 0.2C. The reasons for electrochemical performance of the carbon coated Li₃V₂(PO₄)₃ composites are also discussed. The solid-state reaction is feasible for the preparation of the carbon coated Li₃V₂(PO₄)₃ composites which can offer favorable properties for commercial applications.     

A promising sol-gel route based on citric acid to synthesize Li3V2(PO4)3/carbon composite material for lithium ion batteries

Li₃V₂(PO₄)₃/carbon composite material was synthesized by a promising sol-gel route based on citric acid using V₂O₅ powder as a vanadium source. Citric acid acts not only as a chelating reagent but also as a carbon source, which enhance the conductivity of the composite material and hinder the growth of Li₃V₂(PO₄)₃ particles. The structure and morphology of the sample were characterized by TG, XRD and TEM measurements. XRD results reveal that Li₃V₂(PO₄)₃/carbon was successfully synthesized and has a monoclinic structure with space group P2₁/n. TEM images show Li₃V₂(PO₄)₃ particles are about 45 nm in diameter embeded in carbon networks. Galvanostatic charge/discharge and cyclic voltammetry measurements were used to study its electrochemical behaviors which indicate the reversibility of the lithium extraction/insertion processes. Li₃V₂(PO₄)₃/carbon performed in a voltage window (3.0-4.8 V) exhibits higher discharge capacity, better cycling stability and its discharge capacity maintains about 167.6 mAh/g at a current density of 28 mA/g after 50 cycles.     

Long-term cyclability and high-rate capability of Li3V2(PO4)3/C cathode material using PVA as carbon source

The Li₃V₂(PO₄)₃/C composite cathode material is synthesized via a simple carbothermal reduction reaction route using polyvinyl alcohol (PVA) as both reduction agent and carbon source. The XRD pattern shows that the as-prepared Li₃V₂(PO₄)₃/C composite has a monoclinic structure with space group P2₁/n. The result of XPS shows the oxidation state of V in the Li₃V₂(PO₄)₃/C composite is +3. The Raman spectrum reveals that the coating carbon has a good structure with a low I_D/I_G ratio. The high-quality carbon can not only enhance the electronic conductivity of the Li₃V₂(PO₄)₃/C composite but also prevent the growth of the particle size. The electrochemical performance, which is especially notable for its high-rate performance, is excellent. It delivers an initial discharge capacity of 105.3 mAh/g at 5 C, which is retained as high as 90% after 2000 cycles. No capacity loss can be observed up to 300 cycles under 20 C rate condition. Our experimental results suggest that this compound can be a candidate as cathode materials for the power batteries of hybrid electric vehicles (HEVs) and electric vehicles (EVs) in the future.     

Facile high yield synthesis of MgCo2O4 and investigation of its role as anode material for lithium ion batteries

In this article, we have reported a one-step scalable synthesis of MgCo₂O₄ nanostructures as efficient anode material for Li-ion batteries and investigated the role of post-synthesis calcination temperature (400, 600 and 800 °C) on its physiochemical properties and electrochemical performances. The XRD pattern of the calcinated sample at 400 °C (MC 400) indicates a pure phase of MgCo₂O₄. However, on increasing the calcination temperature to 600 °C (MC 600), an additional phase corresponding to MgO was detected and the corresponding XRD peak intensity further increased on increasing the calcination temperature to 800 °C (MC 800 °C). This was accompanied by a morphological transformation from flake and rod-like nanostructures, to an agglomerated dense flake-like morphology. Electrochemical studies revealed that the calcination temperature plays an important role in determining the electrochemical performance of the MgCo₂O₄ as anode material. In a half cell, the MC 600 showed the best electrochemical performance with high discharge capacity of 980 mA h g⁻¹ (2nd discharge at 60 mA g⁻¹) and a reversible discharge capacity of 886 mA h g⁻¹ at the end of 50 cycles with high coulombic efficiency of 98%. Long term stability was carried out at 0.5C which showed a capacity retention of 358 mA h g⁻¹ at the end of 500 cycles. The superior electrochemical performance of the MC600 can be attributed to the presence of the small amount of MgO, which is believed to provide the anode materials better structural stability during cycling. The claim was further supported by ex-situ TEM analysis of the anode material of a cycled cell (50 cycles).     

Hydrothermal synthesis of Li4Ti5O12 microsphere with high capacity as anode material for lithium ion batteries

Lithium titanate (Li₄Ti₅O₁₂) microsphere has been successfully synthesized by a hydrothermal method. X-ray diffraction (XRD) and scanning electron microscope (SEM) are used to characterize the structure and morphology of the prepared Li₄Ti₅O₁₂ crystallites. The results show that the as-synthesized powders exhibit outstanding rate capacities and excellent cycling performance. The first discharge capacity at 0.1 C is 172.5 mAh g⁻¹, which is close to the theoretical capacity of 175 mAh/g. After 50 cycles, the efficiency of the synthesized Li₄Ti₅O₁₂ still retains up to 92.8% at 0.1 C and 95.2% at 0.5 C of its initial value, which present a promising applications as anode materials for lithium ion batteries in hybrid and plug-in hybrid electric vehicles.     

Carbon nanotube capsules encapsulating SnO2 nanoparticles as an anode material for lithium ion batteries

Carbon nanotubes capsules (CNCs) with compact, stout walls and tunable sizes were fabricated by using self-assembly of acid modified carbon nanotubes in a water-in-oil emulsion system. The effect of ultrasonic power on the formation and size of CNCs were investigated. On the basis of fabrication of CNCs, CNCs encapsulating SnO₂ nanoparticles were prepared as anode material for lithium ion batteries. The morphologies, structural characteristics and electrochemical performances of CNCs and CNCs encapsulating SnO₂ nanoparticles were systemically investigated by FE-SEM, TEM, XRD and a series of electrochemical testing techniques. The results showed that the encapsulation amount of SnO₂ in CNCs had a great influence on the reversible capacity and cycle performance of the composites. The composite with appropriate amount of SnO₂ exhibited a high reversible capacity of 383 mAh g⁻¹ and an excellent cyclability with only 0.4% capacity loss/cycle in that CNCs not only could provide high electric conductivity for composites but also effectively accommodate the volume change of SnO₂ during the cycling processes.     

Fabrication of NiO-ZnO/RGO composite as an anode material for lithium-ion batteries

NiO-ZnO/RGO composite was obtained by the annealing of an Ni (OH)₂-Zn (OH)₂/RGO precursor, which has been fabricated by in situ ultrasonic agitation. Moreover, the NiO-ZnO nanoflakes are evenly distributed on the RGO sheets based on the scanning electron microscope (SEM) and transmission electron microscope (TEM) characterization results. When the NiO-ZnO/RGO composite was used as an anode material in lithium-ion batteries (LIBs), the electrodes exhibited a high reversible capacity of 1017 mA h/g at a current density of 100 mA/g after 200 cycles and a specific capacity of 458 mA h/g at 500 mA/g even after 400 cycles. The electrode even reached a capacity of 185 mA h/g at a current density of 2000 mA/g. The excellent electrochemical properties of the NiO-ZnO/RGO composite might be attributable to the NiO-ZnO nanoflakes offering rich electrochemical reaction sites and shortening the diffusion length for lithium ion (Li⁺), as well as the RGO sheets improving the transfer rates of Li⁺ and electron during the charge-discharge process.     

Characterization of structure and electrochemical properties of lithium manganese oxides for lithium secondary batteries hydrothermally synthesized from δ-KxMnO2

Lithium manganese oxides have attracted much attention as cathode materials for lithium secondary batteries in view of their high capacity and low toxicity. In this study, layered manganese oxide (δ-K_xMnO₂) has been synthesized by thermal decomposition of KMnO₄, and four lithium manganese oxide phases have been synthesized for the first time by mild hydrothermal reactions of this material with different lithium compounds. The lithium manganese oxides were characterized by powder X-ray diffraction (XRD), inductively coupled plasma emission (ICPE) spectroscopy, and chemical redox titration. The four materials obtained are rock salt structure Li₂MnO₃, hollandite (BaMn₈O₁₆) structure α-MnO₂, spinel structure LiMn₂O₄, and birnessite structure Li_xMnO₂. Their electrochemical properties used as cathode material for secondary lithium batteries have been investigated. Of the four lithium manganese oxides, birnessite structure Li_xMnO₂ demonstrated the most stable cycling behavior with high Coulombic efficiency. Its reversible capacity reaches 155 mAh g⁻¹, indicating that it is a viable cathode material for lithium secondary batteries.