硼硫共掺杂金刚石薄膜的研究

利用微波等离子体化学气相沉积(MPCVD)技术,以丙酮为碳源．用二甲基二硫和三氧化二硼作掺杂源．在硅衬底上制备了硼与硫共掺杂的金刚石薄膜。用俄歇谱分析金刚石薄膜中硫的含量．用傅里叶红外光谱(FTIR)分析了薄膜表面键结构．用扫描电子显微镜(SEM)观测薄膜的表面形貌．X射线衍射(XRD)和喇曼(Raman)光谱表征膜层的结构。结果表明：微量硼的加入促进硫在金刚石中的固溶度,使硫在金刚石中的掺杂率提高了近50％;随着薄膜中硫含量的增加．薄膜的导电性增加,当薄膜中硫含量达到0．15％(原子分数)时其导电激活能为0.39eV。     

沉积参数对化学气相沉积纳米金刚石薄膜的影响

用强电流直流伸展电弧化学气相沉积金刚石薄膜装置,在CH4-Ar和CH4-H2-Ar气氛中沉积了纳米金刚石薄膜,研究了沉积气氛中H2加入量和沉积压力对金刚石薄膜显微组织和生长机制的影响.沉积气氛中H2含量对金刚石薄膜的表面形貌、晶粒尺寸和生长速度有显著影响,随着H2含量增加,金刚石晶粒尺寸增大,薄膜生长速度提高.在1%CH4-Ar气氛中沉积的纳米金刚石薄膜,晶粒尺寸细小,薄膜表面形貌光滑平整.在1%CH4-少量H2-Ar气氛中沉积的金刚石薄膜,晶粒尺寸小于100nm,薄膜表面形貌较平整.随着沉积压力提高,金刚石薄膜的生长速度增大.用激光Ram an对金刚石薄膜进行了表征.     

Spectroscopic studies of hydrogen related defects in CVD diamond

Thin diamond films prepared by the hot filament chemical vapour deposition (HFCVD) method at various deposition pressures have been characterized using a variety of spectroscopic techniques. Interpretation of the spectral details have provided useful information about the nature of the films. Deposition pressure appears to affect the quality of the diamond films which is reflected in terms of the position and width of the characteristic Raman peak of diamond. Raman spectra of the films prepared at low deposition pressures showed the presence of a sharp peak at ∼1332 cm⁻¹ characteristic of theT _2g mode of diamond. The study of the effect of deposition pressure on the diamond growth, shows that in the range between 20 torr and 60 torr, there is little effect on the width and the shift of the 1332 cm⁻¹ Raman peak. However, at higher pressures the peak showed a blue shift and was considerably broadened. These studies indicate the development of strain in the lattice due to the introduction of unetched hydride layer, at higher deposition pressures, as well as distortions in the lattice leading to partial lifting of the degeneracy of theT _2g mode. A broad band corresponding to the non-diamond phase (which exists at the grain boundaries, interface or as inclusions inside the grain), which can be attributed to the effect of hydrogen impurity creeping into the lattice at higher deposition pressures is also observed. SEM and XRD patterns have confirmed the dominance of diamond phase in these films.     

CVD金刚石膜的场发射机制

利用热灯丝化学气相沉积方法在光滑的钼上沉积了金刚石膜,用扫描电子显微镜和Raman谱对金刚石膜进行了分析。结果表明金刚石膜是由许多金刚石晶粒组成,晶粒间界主要是石墨相,并且在膜内有许多缺陷。金刚石膜的场发射结果表明高浓度CH4形成的金刚石膜场发射阈位电场较低浓度CH4形成的金刚石为低。这意味着杂质（如石墨）和缺陷（悬挂键）极大地影响了膜的场发射性能。根据以上结果,提出了一种CVD金刚石膜的场发射机制即膜内的缺陷增强膜内的电场,石墨增大电子的隧穿系数以增强CVD金刚石膜的场发射。     

Surface and bioproperties of nanocrystalline diamond/amorphous carbon nanocomposite films

Nanocrystalline diamond/amorphous carbon (NCD/a-C) nanocomposite films have been deposited by microwave plasma chemical vapour deposition from CH₄/N₂ mixtures. In order to investigate their suitability as templates for the immobilization of biomolecules, e.g. for applications in biosensors, four differently prepared surfaces, namely as-grown, hydrogen plasma treated, oxygen plasma treated, and chemically treated with aqua regia, have been thoroughly characterized by methods such as XPS, TOF-SIMS, AFM, and contact angle measurements. In addition, in order to investigate the affinity of these surface to non-specific bonding of biomolecules, they have been exposed to bovine serum albumin (BSA). It turned out that already the as-grown surface is hydrogen terminated; the degree of the termination is even slightly improved by the hydrogen plasma treatment. Reaction with aqua regia, on the other hand, led to a partial destruction of the H-termination. The oxygen plasma treatment, finally, causes a termination by O and OH, rather than by carboxylic acid groups. In addition, an increase of sp² bonded carbon is observed. All surfaces were found to be susceptible to attachment of BSA proteins, but the coverage of the hydrogen terminated was lower than that of the O-terminated film. The highest BSA concentrations were found for the aqua regia sample where the H-termination has been removed partially. Finally, our results show that even minor surface contaminations have a great influence on the BSA coverage.     

器件级同质外延CVD金刚石膜上的具有高击穿电压的铝肖特基二极管

用微波等离子体化学气相沉积方法合成高品质同质外延金刚石膜,并且用扫描电镜和阴极荧光分析法评价。为了得到高薄膜生长速率,把甲烷浓度设定在4%。薄膜上的生长丘的数量和大小依赖于生长条件。在本工作的样品中,未发现任何非外延晶粒。室温下的阴极荧光分光结果表明这种金刚石薄膜具有与自由励起子相关的谱峰。氢终端的膜表面制作的铝电极显示了P型整流特性。击穿电压高于380V。实验结果表明,阴极荧光分析法观测到的缺陷和电性能密切相关,并且可以在有室温边发射的金刚石表面上制作具有高击穿电压的整流电极。     

晶粒尺寸对CVD金刚石膜电学特性的影响

通过改变生长参数,采用热丝化学气相沉积(HFCVD)法制备了从10μm到90nm四种晶粒尺寸的金刚石膜,并制作了三明治结构的光电导探测器.采用原子力显微镜和拉曼光谱仪研究了薄膜的结构和表面形貌:表面粗糙度从423nm变化到15nm;晶粒越大,金刚石膜的质量越好.I-V特性测试结果表明随着晶粒尺寸的减小,金刚石膜的电阻率从1011Ω·cm减小到106Ω·cm.在5.9 keV的55Fe X射线辐照下,随着晶粒尺寸的减小,探测器的信噪比(SNR)呈减小趋势.     

采用MPCVD法在硅衬底上选择性生长金刚石膜

采用微波等离子体化学气相沉积（MPCVD）法在附有SiO2掩摸的硅衬底上选择性沉积出了金刚石膜。采用扫描电子显微镜（SEM）和Raman光谱仪对金刚石膜的表面形貌和结构进行了表征。并讨论了衬底温度对金刚石薄膜选择性沉积的影响。得出了较佳的沉积条件。     

热灯丝CVD金刚石膜的微结构和形貌对其电子性质的影响

利用热灯丝CVD法在硅衬底上合成出了金刚石膜。金刚石膜的质量和电子性质由扫描电子显微镜、拉曼谱、阴极发光及霍尔系数测量来表征。实验结果表明,沉积条件对金刚石膜电子性质和质量有重要影响。载流子迁移率随甲烷浓度增加而减少,但场发射随其增加而增强。压阻效应随微缺陷增多而降低。异质外延金刚石膜压阻因子在室温下100微形变时为1200,但含有大量缺陷的多晶金刚石膜压阻因子低于200,这是由于薄膜中缺陷态密度增加,并依赖于膜结构的变化。     

金刚石厚膜的晶界对耐磨性的影响

用直流辉光等离子体化学气相沉积制备金刚石厚膜,用氢的微波等离子体对其抛光截面进行刻蚀,研究了晶界对金刚石厚膜耐磨性的影响.结果表明：在金刚石膜的生长过程中,随着甲烷流量的增加,金刚石膜的晶界从纵向排列为主过渡到网状结构,晶粒内部缺陷逐渐增加,杂质、空洞主要分布于晶界处．金刚石膜的磨耗比随着晶界密度、宽度、杂质含量及晶粒内部缺陷的增加而下降．晶界是杂质、空洞主要富集区,是影响金刚石厚膜耐磨性的主要因素．     

A review of crystallographic textures in chemical vapor-deposited diamond films

Diamond is one of the most important functional materials for film applications due to its extreme physical and mechanical properties, many of which depend on the crystallographic texture. The influence of various deposition parameters matters to the texture formation and evolution during chemical vapor deposition (CVD) of diamond films. In this overview, the texture evolutions are presented in terms of both simulations and experimental observations. The crystallographic textures in diamond are simulated based on the van der Drift growth selection mechanism. The film morphology and textures associated with the growth parameters α (proportional to the ratio of the growth rate along the〈100〉direction to that along the 〈111〉direction) are presented and determined by applying the fastest growth directions. Thick films with variations in substrate temperature, methane concentration, film thickness, and nitrogen addition were analyzed using high-resolution electron back-scattering diffraction (HR-EBSD) as well as X-ray diffraction (XRD), and the fraction variations of fiber textures with these deposition parameters were explained. In conjunction with the focused ion beam (FIB) technique for specimen preparation, the grain orientations in the beginning nucleation zones were studied using HR-EBSD (50nm step size) in another two sets of thin films deposited with variations in methane concentration and substrate material. The microstructures, textures, and grain boundary character were characterized. Based on the combination of an FIB unit for serial sectioning and HR-EBSD, diamond growth dynamics was observed using a 3D EBSD technique, with which individual diamond grains were investigated in 3D. Microscopic defects were observed in the vicinity of the high-angle grain boundaries by using the transmission electron microscopy (TEM) technique, and the advances of TEM orientation microscopy make it possible to identify the grain orientations in nano-crystalline diamond.     

热丝CVD方法中气体状态参数的二维模拟计算

使用在连续介质中建立的二维流场数学模型，模拟计算了在用HFCVD方法生长金刚石薄膜过程中影响气体温度分布的多个沉积工艺参数，研究了气体的速度和体密度的空间分布．结果表明，在优化工艺参数条件下，高温热丝的热阻塞作用导致气体状态参数的不均匀空间分布；在热丝附近气体的速度大而靠近反应腔体侧壁处小；热丝附近处气体体密度减小而靠近冷反应腔体侧壁处增加，采用绝热或高等温边界的反应腔管道壁可以消除气体的热绕流现象，有利于大面积金刚石薄膜的快速均匀生长．     

Field emission studies of CVD diamond thin films: effect of acid treatment

Field emission from CVD diamond thin films deposited on silicon substrate has been studied. The diamond films were synthesized using hot filament chemical vapor deposition technique. Field emission studies of as-deposited and acid-treated films were carried out using ‘diode’ configuration in an all metal UHV chamber. Upon acid treatment, the field emission current is found to decrease by two orders of magnitude with increase in the turn-on voltage by 30%. This has been attributed to the removal of sp² content present in the film due to acid etching. Raman spectra of both the as-deposited and acid-treated films exhibit identical spectral features, a well-defined peak at 1333 cm⁻¹ and a broad hump around 1550 cm⁻¹, signatures of diamond (sp³ phase) and graphite (sp² phase), respectively. However upon acid treatment, the ratio (I_d/I_g) is observed to decrease which supports the speculation of removal of sp² content from the film. The surface roughness was studied using atomic force microscopy (AFM). The AFM images indicate increase in the number of protrusions with slight enhancement in overall surface roughness after acid etching. The degradation of field emission current despite an increase in film surface roughness upon acid treatment implies that the sp² content plays significant role in field emission characteristics of CVD diamond films.     

氢稀释对纳米晶硅薄膜微结构的影响

采用电感耦合等离子体化学气相沉积技术制备了氮化纳米硅薄膜,利用Raman散射、x射线衍射、红外吸收等技术对不同氮稀释条件下薄膜的微观结构和键合特性变化进行了研究.结果表明,较高的氢稀释比导致薄膜从非晶硅到纳米晶硅的结构转化,随着氮稀释比的增加,所沉积薄膜的晶化度及纳米晶硅的晶粒尺寸单调增加,纳米硅颗粒呈现在(110)方...     

金刚石膜的磁阻效应和压阻效应

介绍了p型异质外延金刚石膜磁阻效应和压阻效应的特性及应用展望，阐述了目前理论和实验的研究状况，提出了今后有待进一步研究的问题。     

A 3D tomographic EBSD analysis of a CVD diamond thin film

We have studied the nucleation and growth processes in a chemical vapor deposition (CVD) diamond film using a tomographic electron backscattering diffraction method (3D EBSD). The approach is based on the combination of a focused ion beam (FIB) unit for serial sectioning in conjunction with high-resolution EBSD. Individual diamond grains were investigated in 3-dimensions particularly with regard to the role of twinning.     

A 3D tomographic EBSD analysis of a CVD diamond thin film

Abstract

We have studied the nucleation and growth processes in a chemical vapor deposition (CVD) diamond film using a tomographic electron backscattering diffraction method (3D EBSD). The approach is based on the combination of a focused ion beam (FIB) unit for serial sectioning in conjunction with high-resolution EBSD. Individual diamond grains were investigated in 3-dimensions particularly with regard to the role of twinning.     

Processing of nanocrystalline diamond thin films for thermal management of wide-bandgap semiconductor power electronics

High current densities in wide-bandgap semiconductor electronics operating at high power levels results in significant self-heating of devices, which necessitates the development thermal management technologies to effectively dissipate the generated heat. This paper lays the foundation for the development of such technology by ascertaining process conditions for depositing nanocrystalline diamond (NCD) on AlGaN/GaN High Electron Mobility Transistors (HEMTs) with no visible damage to device metallization. NCD deposition is carried out on Si and GaN HEMTs with Au/Ni metallization. Raman spectroscopy, optical and scanning electron microscopy are used to evaluate the quality of the deposited NCD films. Si device metallization is used as a test bed for developing process conditions for NCD deposition on AlGaN/GaN HEMTs. Results indicate that no visible damage occurs to the device metallization for deposition conditions below 290 °C for Si devices and below 320 °C for the AlGaN/GaN HEMTs. Possible mechanisms for metallization damage above the deposition temperature are enumerated. Electrical testing of the AlGaN/GaN HEMTs indicates that it is indeed possible to deposit NCD on GaN-based devices with no significant degradation in device performance.     

Correlation between resistivity and oxygen vacancy of hydrogen-doped indium tin oxide thin films

Thin films of indium tin oxide (ITO) sputter-deposited by dc-plasma containing deuterium on glass substrate without any heat treatments exhibited gradual lowering in electrical resistivity with increasing the deuterium content [D₂] in plasma gas by 1% and then demonstrated a jump in resistivity by further increase of [D₂] than 1%. X-ray photoelectron spectroscopy revealed that hydroxyl-bonded oxygen in ITO grew continuingly with [D₂]. Deuterium positioned at the interstitial site increased almost quantitatively with increasing [D₂]. Rutherford backscattering spectroscopy showed gradual reduction in the oxygen content of ITO with increasing [D₂] by 1% and then demonstrated an abrupt increase of the oxygen content with the increase of [D₂] than 1%. The films with [D₂] < 1% were oxygen deficient, but those with [D₂] > 1% were excess of oxygen. The most oxygen deficient film of [D₂] = 1% was the most conductive. Behavior in the resistivity with [D₂] looks parallel to that in the oxygen content. A lower resistivity of the films corresponded well to oxygen vacancy rather than hydrogen interstitial.