Microwave activation of electrochemical processes: High temperature phenol and triclosan electro-oxidation at carbon and diamond electrodes

The electrochemical oxidation of phenolic compounds in aqueous media is known to be affected by the formation of electro-polymerized organic layers which lead to partial or complete electrode blocking. In this study the effect of high intensity microwave radiation applied locally at the electrode surface is investigated for the oxidation of phenol and triclosan in alkaline solution at a 500 μm diameter glassy carbon or at a 500 μm × 500 μm boron-doped diamond electrode. The temperature at the electrode surface and mass transport enhancement are determined by calibration with the Fe(CN)₆^3−/4− redox system in aqueous 0.3 M NaOH and 0.2 NaCl (pH 12) solution. The calibration shows that strong thermal and mass transport effects occur at both glassy carbon and boron-doped diamond electrodes. The average electrode temperature reaches up to 390 K and mass transport enhancements of more than 20-fold are possible. For the phenol electro-oxidation at glassy carbon electrodes and at a concentration below 2 mM a multi-electron oxidation (ca. 4 electrons) occurs in the presence of microwave radiation. For the electro-oxidation of the more hydrophobic triclosan only the one-electron oxidation occurs. Although currents are enhanced in presence of microwave radiation, rapid blocking of the electrode surface in particular at high phenol concentrations still occurs.     

Electrochemical studies of ganciclovir at boron-doped nanocrystalline diamond electrodes

The electrochemical oxidation of ganciclovir was investigated at boron-doped nanocrystalline diamond (BDND) electrodes by the use of cyclic voltammetry and differential pulse voltammetry. The optimization of the experimental variables including supporting electrolyte and pH value was studied, and the 0.04-M Britton-Robinson buffer solution (pH 2.5) was selected. The relationship of the oxidation peak potential to scan rate and pH value was also investigated, and 2 electron transfer and 2 proton participation for the oxidation process of ganciclovir at BDND electrode were obtained. Compared with boron-doped microcrystalline diamond and glassy carbon electrodes, the BDND electrode demonstrated the wider linear range of 0.5-350 μM, lower limit of detection of 0.2 μM, and higher reproducibility and stability for the determination of ganciclovir under the optimum conditions. For the analysis of ganciclovir in human serum at the BDND electrodes, precision and accuracy were checked by recovery experiments.     

Anodic voltammetry of abacavir and its determination in pharmaceuticals and biological fluids

Abacavir has an antiretroviral activity against HIV and is oxidizable at the glassy carbon electrode. Cyclic voltammetry studies showed one well-defined oxidation wave or splitted two waves depending on pH. The oxidation was irreversible and exhibited diffusion controlled process depending on pH. The mechanism of the oxidation process was discussed. According to the linear relation between the peak current and the concentration, differential pulse voltammetric (DPV) and square wave voltammetric (SWV) methods for its quantitative determination in pharmaceutical dosage forms and biological fluids were developed. These two voltammetric techniques for the determination of abacavir in Britton-Robinson buffer at pH 2.0, which allows quantitation over the 8×10⁻⁷ to 2×10⁻⁴ M range in supporting electrolyte for both methods were proposed. The linear response was obtained in Britton-Robinson buffer in the ranges of 1×10⁻⁵ to 1×10⁻⁴ M for spiked urine sample at pH 2.0 and 2×10⁻⁵ to 2×10⁻⁴ M for spiked serum samples at pH 3.0 for both techniques. The repeatability and reproducibility of the methods for all media (such as supporting electrolyte, serum and urine samples) were determined. Precision and accuracy were also checked in all media. The standard addition method was used in biological media. No electroactive interferences from the endogenous substances were found in the biological fluids.     

DNA Langmuir-Blodgett modified glassy carbon electrode as voltammetric sensor for determinate of methotrexate

A highly sensitive electrochemical biosensor for the detection of trace amounts of methotrexate has been designed. Double stranded (ds)DNA molecules are immobilized onto a pretreated glassy carbon electrode (GCE(ox)) surface with Langmuir-Blodgett (LB) technique. The adsorptive voltammetric behaviors of methotrexate on DNA-modified electrode were explored by means of cyclic voltammetry (CV) and square wave voltammetry (SWV). The oxidation mechanism was proposed and discussed in this work. In addition, the optimum experimental conditions for the detection of methotrexate were explored, and the currents measured by SWV presented a good linear property as a function of the concentrations of methotrexate in the range of 2.0 × 10⁻⁸ to 4.0 × 10⁻⁶ mol L⁻¹, with an LOD of 5.0 × 10⁻⁹ mol L⁻¹. The method proposed was applied for the determination of methotrexate in pharmaceutical dosage and diluted human urine with wonderful satisfactory successfully.     

Electrochemical study on cobalt film modified glassy carbon electrode and its application

A novel electroactive material for ascorbic acid (AA) determination was successfully prepared by plating/potential cycling method. The cobalt film was first deposited on the surface of glassy carbon electrode (GCE) in CoSO₄ solution by potential cycling, and then a cobalt film on the surface of GCE was activated by potential cycling in 0.1 mol L⁻¹ NaOH. The electrochemical performance of the resulted film (Co/GCE) and factors affecting its electrochemical activity were investigated by cyclic voltammetry and amperometry. This film electrode exhibited good electrocatalytic activity to the oxidation of AA. This biosensor had a fast response of AA less than 3 s and excellent linear relationships were obtained in the concentration range of 3 × 10⁻⁷ to 1 × 10⁻⁴ mol L⁻¹ with a detection limit of 2 × 10⁻⁷ mol L⁻¹ (S/N = 3) under the optimum conditions. Moreover, the selectivity, stability and reproducibility of this biosensor were evaluated with satisfactory results.     

Investigations of electrochemical oxygen transfer reaction on boron-doped diamond electrodes

In this paper, the electrochemical oxygen transfer reaction (EOTR) is studied on boron-doped diamond electrodes using simple C₁ organic compounds (methanol and formic acid). The kinetics of both oxygen evolution (side reaction) and organics oxidation (main reaction) has been investigated using boron-doped diamond microelectrodes-array (BDD MEA). Oxygen evolution, in the high-potential region, takes place with a Tafel slope of 120 mV dec⁻¹ and zero reaction order with respect to H⁺. In the presence of organics, a shift of the polarization curves to lower potentials is observed while the Tafel slopes remain close to 120 mV dec⁻¹. A simplified model of C₁ organics oxidation is proposed. Both water discharge and organics oxidation are assumed to be fast reactions. The slowest step of the studied EOTR is the anodic discharge of hydroxyl radicals to oxygen. Further in this work, electrolysis of formic acid on boron-doped diamond macroelectrode is presented. In order to achieve 100% current efficiency, electrolysis was carried out under programmed current, in which the current density was adjusted to the limiting value.     

Anodic behaviour of fulvestrant and its voltammetric determination in pharmaceuticals and human serum on highly boron-doped diamond electrode using differential pulse adsorptive stripping voltammetry

The electrochemical oxidation of fulvestrant was made on highly boron-doped diamond electrode using differential pulse adsorptive stripping voltammetry. The highest current intensities were obtained by applying +1.10 V during 150 s for boron-doped diamond electrode. For boron-doped diamond electrode, linear responses were obtained for the concentrations between 1 × 10⁻⁶ and 8 × 10⁻⁵ M in standard samples and between 1 × 10⁻⁶ and 4 × 10⁻⁵ M in serum samples. The repeatability of the method was 0.55 RSD% for differential pulse adsorptive stripping voltammetry. The analytical values of the method are demonstrated by quantitative determination of fulvestrant in pharmaceutical formulations and human serum, without the need for separation or complex sample preparation, since there was no interference from the excipients and endogenous substances. Selectivity, reproducibility, and accuracy of the developed methods were demonstrated by recovery studies.     

Cobalt hydroxide film deposited on glassy carbon electrode for electrocatalytic oxidation of hydroquinone

The electrodeposition of cobalt hydroxide film on glassy carbon electrode was prepared by electrochemical method in an alkaline aqueous solution. The electrochemical behavior of hydroquinone on cobalt hydroxide film electrode has been investigated by using cyclic voltammetry and linear sweep voltammetry. The results showed that the film electrode has good electrocatalytic ability for the oxidation of hydroquinone to p-quinone. The recovery of hydroquinone from sample ranged from 94.7% to 102.9% and a rectilinear analytical curve for hydroquinone concentration from 5.0 × 10⁻⁶ to 1.25 × 10⁻⁴ mol/L was obtained. The detection limit was 5.0 × 10⁻⁷ mol/L and the relative standard deviation was 2.63%. Various factors affecting the electrocatalytic activity of cobalt hydroxide film were investigated.     

Synthesis and characterization of electroactive polyamide with amine-capped aniline pentamer and ferrocene in the main chain by oxidative coupling polymerization

A novel electroactive polymer, polyamide with well-defined oligoaniline and ferrocene in the main chain, has been successfully synthesized through a novel oxidative coupling polymerization. The polymerization characteristics and structure of the copolymer were systematically studied by gel permeation chromatographic (GPC), Fourier-transform infrared (FTIR) spectra, ¹H NMR and X-ray powder diffraction (XRD). And its spectroscopic properties and electrochemical behavior were studied by UV-vis spectra and cyclic voltammetry (CV). It was found that the obtained polyamide bearing amine-capped aniline pentamer and ferrocene segments had a reversible electrochemical property in the cyclic voltammetry, but showed four distinct oxidation states, which is different from polyaniline. Moreover, its electrical conductivity is about 7.6×10⁻⁷ S cm⁻¹ at room temperature upon preliminarily protonic-doped experiment.     

Hybridization biosensor using sodium tanshinone IIA sulfonate as electrochemical indicator for detection of short DNA species of chronic myelogenous leukemia

Cyclic voltammetry (CV) was used to investigate electrochemical behavior of sodium tanshinone IIA sulfonate (STS) and the interaction between STS and salmon sperm DNA. STS had excellent electrochemical activity on the glassy carbon electrode (GCE) with a couple reversible redox peaks. In pH 4.0 phosphate buffer solution (PBS), the binding ratio between STS and salmon sperm DNA was calculated to be 1:1 and the binding constant was 1.67 × 10⁴ L/mol. A chronic myelogenous leukemia (CML, Type b3a2) DNA biosensor was developed by immobilizing covalently single-stranded CML DNA fragment to a modified GCE. The surface hybridization of the immobilized single-stranded CML DNA fragment with its complementary DNA fragment was evidenced by electrochemical methods using STS as a novel electrochemical indicator, with a detection limit of 6.7 × 10⁻⁹ M and a linear range from 2.0 × 10⁻⁸ M to 2.0 × 10⁻⁷ M. Selective determination of complementary ssDNA was achieved using differential pulse voltammetry (DPV).     

Simultaneous voltammetric determination of acetaminophen, aspirin and caffeine using an in situ surfactant-modified multiwalled carbon nanotube paste electrode

A carbon nanotube paste electrode modified in situ with Triton X 100 was developed for the individual and simultaneous determination of acetaminophen (ACOP), aspirin (ASA) and caffeine (CF). The electrochemical behavior of these three molecules was investigated employing cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), chronocoulometry (CC) and adsorptive stripping differential pulse voltammetry (AdSDPV). Kramers-Kronig transformation implied that the resulting impedance data were validated and were of very good quality. These studies revealed that the oxidation of ACOP, ASA and CF is facilitated at an in situ surfactant-modified multiwalled carbon nanotube paste electrode (ISSM-CNT-PE). After optimization of analytical conditions employing this electrode at pH 7.0 in phosphate buffer (0.1 M), the peak currents for the three molecules were found to vary linearly with their concentrations in the range of 2.91 × 10⁻⁷-6.27 × 10⁻⁵ M with detection limits of 2.58 × 10⁻⁸, 8.47 × 10⁻⁸ and 8.83 × 10⁻⁸ M for ACOP, ASA and CF respectively using AdSDPV. The prepared modified electrode showed several advantages, such as a simple preparation method, high sensitivity, very low detection limits and excellent reproducibility. Furthermore, the proposed method was employed for the simultaneous determination of ACOP, ASA and CF in pharmaceutical formulations, urine and blood serum samples and the obtained results were found to be satisfactory.     

Electrochemical determination of bisphenol A at Mg-Al-CO3 layered double hydroxide modified glassy carbon electrode

The electrochemical behavior of bisphenol A (BPA) was investigated on Mg-Al layered double hydroxide (LDH) modified glassy carbon electrode (GCE) by cyclic voltammetry (CV), differential pulse voltammetry (DPV), linear sweep voltammetry (LSV) and chronocoulometry (CC). The cyclic voltammogram of BPA on the modified electrode exhibited a well defined anodic peak at 0.454 V in 0.1 M pH 8.0 phosphate buffer solution (PBS). The experimental parameters were optimized and the kinetic parameters were investigated. The probable oxidation mechanism was proposed. Under the optimized conditions, the oxidation peak current was proportional to BPA concentration in the range from 1 × 10⁻⁸ to 1.05 × 10⁻⁶ M with the correlation coefficient of 0.9959. The detection limit was 5.0 × 10⁻⁹ M (S/N = 3). The fabricated electrode showed good reproducibility, stability and anti-interference. The proposed method was successfully applied to determine BPA in plastic products and the results were satisfactory.     

Voltammetric determination of ascorbic acid and dopamine in the same sample at the surface of a carbon paste electrode modified with polypyrrole/ferrocyanide films

Functionalized polypyrrole film were prepared by incorporation of [Fe(CN)₆]⁴⁻ as a doping anion, during the electropolymerization of pyrrole onto a carbon paste electrode in an aqueous solution by potentiostatic method. The electrochemical behavior of dopamine (DA) and ascorbic acid (AA) in one solution was studied at the surface of bare and modified carbon paste electrodes using cyclic voltammetry (CV), linear sweep voltammetry (LSV) and differntial pulse voltammetry (DPV) methods. The well separated anodic peaks for oxidation of DA and AA were observed at the surface of the modified carbon paste electrode under optimum condition (pH 6.00), which can be used for determination of these species simultaneously in mixture by LSV and DPV methods. The linear analytical curves were obtained in the ranges of 0.10-1.00 mM and 0.10-0.95 mM for ascorbic acid and 0.10-1.20 mM and 0.20-0.95 mM for dopamine concentrations using LSV and DPV methods, respectively. The detection limits (2σ) were determined as 3.38 × 10⁻⁵ M and 1.34 × 10⁻⁵ M of ascorbic acid and 3.86 × 10⁻⁵ M and 1.51 × 10⁻⁵ M of dopamine by CV and DPV methods.     

Electroanalytical application of modified diamond electrodes

Metal-modified diamond electrodes were fabricated by using ion implantation method for electroanalytical applications. Nickel and copper ion were implanted at a different film of boron-doped diamond (BDD) with a dose of 5×10¹⁴ cm⁻² for each type of ion. The electrochemical behavior has been studied for glucose oxidation in alkaline media by using cyclic voltammetry and flow injection analysis. Those electrodes exhibited high catalytic activity and excellent electrochemical stability with low background current even after strong ultrasonication in the cleaning process. The results indicate that metal-implanted method could be a promising method for controlling the electrochemical properties of diamond electrodes.     

Fabrication of CeO2 nanoparticles modified glassy carbon electrode and its application for electrochemical determination of UA and AA simultaneously

A glassy carbon electrode modified with CeO₂ nanoparticles was constructed and was characterized by electrochemical impedance spectrum (EIS) and cyclic voltammetry (CV). The resulting CeO₂ nanoparticles modified glassy carbon electrode (CeO₂ NP/GC electrode) was used to detect uric acid (UA) and ascorbic acid (AA) simultaneously in mixture. This modified electrode exhibits potent and persistent electron-mediating behavior followed by well-separated oxidation peaks towards UA and AA with activation overpotential. For UA and AA in mixture, one can well separate from the other with a potential difference of 273 mV, which was large enough to allow the determination of one in presence of the other. The DPV peak currents obtained in mixture increased linearly on the UA and AA in the range of 5.0 × 10⁻⁶ to 1.0 × 10⁻³ mol/L and 1.0 × 10⁻⁶ to 5.0 × 10⁻⁴ mol/L, with the detection limit (signal-to-noise ratio was 3) for UA and AA were 2.0 × 10⁻⁷ and 5.0 × 10⁻⁶ mol/L, respectively. The proposed method showed excellent selectivity and stability, and the determination of UA and AA simultaneously in serum was satisfactory.     

Electrochemical detection of l-cysteine using a boron-doped carbon nanotube-modified electrode

A boron-doped carbon nanotube (BCNT)-modified glassy carbon (GC) electrode was constructed for the detection of l-cysteine (L-CySH). The electrochemical behavior of BCNTs in response to l-cysteine oxidation was investigated. The response current of L-CySH oxidation at the BCNT/GC electrode was obviously higher than that at the bare GC electrode or the CNT/GC electrode. This finding may be ascribed to the excellent electrochemical properties of the BCNT/GC electrode. Moreover, on the basis of this finding, a determination of L-CySH at the BCNT/GC electrode was carried out. The effects of pH, scan rate and interferents on the response of L-CySH oxidation were investigated. Under the optimum experimental conditions, the detection response for L-CySH on the BCNT/GC electrode was fast (within 7 s). It was found to be linear from 7.8 × 10⁻⁷ to 2 × 10⁻⁴ M (r = 0.998), with a high sensitivity of 25.3 ± 1.2 nA mM⁻¹ and a low detection limit of 0.26 ± 0.01 μM. The BCNT/GC electrode exhibited high stability and good resistance against interference by other oxidizable amino acids (tryptophan and tyrosine).     

Electrochemical incineration of chloranilic acid using Ti/IrO2, Pb/PbO2 and Si/BDD electrodes

The electrochemical oxidation of chloranilic acid (CAA) has been studied in acidic media at Pb/PbO₂, boron-doped diamond (Si/BDD) and Ti/IrO₂ electrodes by bulk electrolysis experiments under galvanostatic control. The obtained results have clearly shown that the electrode material is an important parameter for the optimization of such processes, deciding of their mechanism and of the oxidation products. It has been observed that the oxidation of CAA generates several intermediates eventually leading to its complete mineralization. Different current efficiencies were obtained at Pb/PbO₂ and BDD, depending on the applied current density in the range from 6.3 to 50 mA cm⁻². Also the effect of the temperature on Pb/PbO₂ and BDD electrodes was studied.UV spectrometric measurements were carried out at all anodic materials, with applied current density of 25 and 50 mA cm⁻². These results showed a faster CAA elimination at the BDD electrode. Finally, a mechanism for the electrochemical oxidation of CAA has been proposed according to the results obtained with the HPLC technique.     

Voltammetric studies of a cobalt(II)-4-methylsalophen modified carbon-paste electrode and its application for the simultaneous determination of cysteine and ascorbic acid

A carbon-paste electrode (CPE) chemically modified with the cobalt(II)-4-methylsalophen (CoMSal) as a Schiff base complex was used as a highly sensitive and fairly selective electrochemical sensor for simultaneous determination of minor mounts of ascorbic acid (AA) and cysteine. This modified electrode shows very efficient electrocatalytic activity for anodic oxidation of both AA and cysteine via substantially decreasing of anodic overpotentials for both compounds. The mechanism of electrochemical oxidation of both AA and cysteine using CoMSal-modified electrode was thoroughly investigated by cyclic voltammetry and polarization studies. Results of cyclic voltammetry (CV) and differential pulse voltammetry (DPV) using this modified electrode show two well-resolved anodic waves for the oxidation of AA and cysteine, which makes it possible for simultaneous determination of both compounds. A linear range of 1 × 10⁻⁴ to 5 × 10⁻⁷ M for cysteine in a constant concentration of 1 × 10⁻⁴ M AA in buffered solution (as a background electrolyte) was obtained from DPV measurements using this electrode. The linear range, which is obtained for AA in the presence of 1 × 10⁻⁴ M cysteine, was in the range of 1 × 10⁻⁴ to 1 × 10⁻⁶ M. The modified electrode has good reproducibility (RSD ≤ 2.5%), low detection limit (sub-micromolar) and high sensitivity for the detection of both AA and cysteine with a very high stability in its voltammetric response. Differential pulse voltammetry using the modified electrode exhibited a reasonable recovery for a relatively wide concentration range of cysteine spiked to a synthetic human serum sample.     

Electrocatalytic hydrazine oxidation on quinizarine modified glassy carbon electrode

The electrocatalytic oxidation of hydrazine has been studied on glassy carbon modified by electrodeposition of quinizarine, using cyclic voltammetry and chronoamperometry techniques. It has been shown that the oxidation of hydrazine to nitrogen occurs at a potential where oxidation is not observed at the bare glassy carbon electrode. The apparent charge transfer rate constant and transfer coefficient for electron transfer between the electrode surface and immobilized quinizarine were calculated as 4.44 s⁻¹ and 0.66, respectively. The heterogenous rate constant for oxidation of hydrazine at the quinizarine modified electrode surface was also determined and found to be about 4.83 × 10³ M⁻¹ s⁻¹. The diffusion coefficient of hydrazine was also estimated as 1.1 × 10⁻⁶ cm² s⁻¹ for the experimental conditions, using chronoamperometry.     

Adsorptive stripping differential pulse voltammetric determination of venlafaxine and desvenlafaxine employing Nafion–carbon nanotube composite glassy carbon electrode

A Nafion-carbon nanotube-modified glassy carbon electrode (NAF-CNT-GCE) was developed for the determination of venlafaxine (VF) and desvenlafaxine (DVF). The electrochemical behavior of both these molecules was investigated employing cyclic voltammetry (CV), chronocoulometry (CC), electrochemical impedance spectroscopy (EIS) and adsorptive stripping differential pulse voltammetry (AdSDPV). The surface morphology of the electrodes has been studied by means of scanning electron microscopy (SEM). These studies revealed that the oxidation of VF and DVF is facilitated at NAF-CNT-GCE. After optimization of analytical conditions employing this electrode at pH 7.0 in Britton–Robinson buffer (0.05 M) for VF and pH 5.0 in acetate buffer (0.1 M) for DVF, the peak currents for both the molecules were found to vary linearly with their concentrations in the range of 3.81 × 10⁻⁸–6.22 × 10⁻⁵ M for VF and 5.33 × 10⁻⁸–3.58 × 10⁻⁵ M for DVF. The detection limits (S/N = 3) of 1.24 × 10⁻⁸ and 2.11 × 10⁻⁸ M were obtained for VF and DVF, respectively, using AdSDPV. The prepared modified electrode showed several advantages, such as simple preparation method, high sensitivity, very low detection limits and excellent reproducibility. The proposed method was employed for the determination of VF and DVF in pharmaceutical formulations, urine and blood serum samples.