Equilibrium, kinetics and mechanism of malachite green adsorption on activated carbon prepared from bamboo by K(2)CO(3) activation and subsequent gasification with CO(2)

In this work, the adsorption of malachite green (MG) was studied on activated carbon prepared from bamboo by chemical activation with K(2)CO(3) and physical activation with CO(2) (BAC). Adsorption studies were conducted in the range of 25-300 mg/L initial MG concentration and at temperature of 30 degrees C. The experimental data were analyzed by the Freundlich isotherm, the Langmuir isotherm, and the multilayer adsorption isotherm. Equilibrium data fitted well with the Langmuir model with maximum adsorption capacity of 263.58 mg/g. The rates of adsorption were found to confirm to pseudo-second-order kinetics with good correlation and the overall rate of dye uptake was found to be controlled by pore diffusion throughout the entire adsorption period. The results indicate that the BAC could be used to effectively adsorb MG from aqueous solutions.     

Batch removal of malachite green from aqueous solutions by adsorption on oil palm trunk fibre: equilibrium isotherms and kinetic studies

Oil palm trunk fibre (OPTF)--an agricultural solid waste--was used as low-cost adsorbent to remove malachite green (MG) from aqueous solutions. The operating variables studied were contact time, initial dye concentration, and solution pH. Equilibrium adsorption data were analyzed by three isotherms, namely the Freundlich isotherm, the Langmuir isotherm, and the multilayer adsorption isotherm. The best fit to the data was obtained with the multilayer adsorption. The monolayer adsorption capacity of OPTF was found to be 149.35 mg/g at 30 degrees C. Adsorption kinetic data were modeled using the Lagergren pseudo-first-order, Ho's pseudo-second-order and Elovich models. It was found that the Lagergren's model could be used for the prediction of the system's kinetics. The overall rate of dye uptake was found to be controlled by external mass transfer at the beginning of adsorption, then for initial MG concentrations of 25, 50, 100, 150, and 300 mg/L the rate-control changed to intraparticle diffusion at a later stage, but for initial MG concentrations 200 and 250 mg/L no evidence was found of intraparticle diffusion at any period of adsorption. It was found that with increasing the initial concentration of MG, the pore-diffusion coefficient increased while the film-diffusion coefficient decreased.     

Kinetics and equilibrium studies of malachite green adsorption on rice straw-derived char

In this work, the potential feasibility of rice straw-derived char (RSC) for removal of C.I. Basic Green 4 (malachite green (MG)), a cationic dye from aqueous solution was investigated. The isotherm parameters were estimated by non-linear regression analysis. The equilibrium process was described well by the Langmuir isotherm model. The maximum RSC sorption capacity was found to be 148.74 mg/L at 30 degrees C. The kinetics of MG sorption on RSC followed the Lagergren's pseudo-first-order model and the overall rate of dye uptake was found to be controlled by external mass transfer at the beginning of adsorption, while intraparticle diffusion controlled the overall rate of adsorption at a later stage. The results indicated that RSC was an attractive adsorbent for removing basic dye from aqueous solutions.     

The adsorption of Cd(II) ions on sulphuric acid-treated wheat bran

The adsorption of Cd(II) ions which is one of the most important toxic metals by using sulphuric acid-treated wheat bran (STWB) was investigated. The effects of solution pH and temperature, contact time and initial Cd(II) concentration on the adsorption yield were studied. The equilibrium time for the adsorption process was determined as 4 h. The adsorbent used in this study gave the highest adsorption capacity at around pH 5.4. At this pH, adsorption capacity for an initial Cd(II) ions concentration of 100 mg/L was found to be 43.1 mg/g at 25 degrees C for contact time of 4 h. The equilibrium data were analysed using Langmuir and Freundlich isotherm models to calculate isotherm constants. The maximum adsorption capacity (qmax) which is a Langmuir constant decreased from 101.0 to 62.5 mg/g with increasing temperature from 25 to 70 degrees C. Langmuir isotherm data were evaluated to determine the thermodynamic parameters for the adsorption process. The enthalpy change (deltaH(o)) for the process was found to be exothermic. The free energy change (deltaG(o)) showed that the process was feasible. The kinetic results indicated that the adsorption process of Cd(II) ions by STWB followed first-order rate expression and adsorption rate constant was calculated as 0.0081 l/min at 25 degrees C. It was observed that the desorption yield of Cd(II) was highly pH dependent.     

Adsorptions of high concentration malachite green by two activated carbons having different porous structures

The adsorption of malachite green (MG) from aqueous solution by two different adsorbents (CZn5, PETNa8) were studied. Adsorbents were prepared from pine sawdust and polyethyleneterephatalate (PET) by chemical activation with ZnCl(2) and NaOH, respectively. The adsorption was carried out in a batch system as a function of dye concentration, pH and contact time. Both adsorbents were found to be very effective in removing the dye at high concentration with adsorption percentage in the order of CZn5 > PETNa8. The pH of dye solution in the range of 6-10, was found favorable for the removal of malachite green by using the two adsorbents at high concentrations. Equilibrium times were 120 and 90 min for CZN5 and PETNa8, respectively. Kinetics of removal MG was studied using Lagergren equation and diffusion phenomena was analyzed using Weber and Morris intraparticle diffusion plots. It was also showed that the adsorption isotherm followed Langmuir model.     

Removal of malachite green by using an invasive marine alga Caulerpa racemosa var. cylindracea

The biosorption of a cationic dye, malachite green oxalate (MG) from aqueous solution onto an invasive marine alga Caulerpa racemosa var. cylindracea (CRC) was investigated at different temperatures (298, 308 and 318 K). The dye adsorption onto CRC was confirmed by FTIR analysis. Equilibrium data were analyzed using Freundlich, Langmuir and Dubinin-Radushkevich (DR) equations. All of the isotherm parameters were calculated. The Freundlich model gave a better conformity than Langmuir equation. The mean free energy values (E) from DR isotherm were also estimated. In order to clarify the sorption kinetic, the fit of pseudo-first-order kinetic model, second-order kinetic model and intraparticle diffusion model were investigated. It was obtained that the biosorption process followed the pseudo-second-order rate kinetics. From thermodynamic studies the free energy changes were found to be -7.078, -9.848 and -10.864 kJ mol(-1) for 298, 308 and 318 K, respectively. This implied the spontaneous nature of biosorption and the type of adsorption as physisorption. Activation energy value for MG sorption (E(a)) was found to be 37.14 kJ mol(-1). It could be also derived that this result supported physisorption as a type of adsorption.     

Removal of Acid Violet 17 from aqueous solutions by adsorption onto activated carbon prepared from sunflower seed hull

The adsorption of Acid Violet 17 (AV17) was carried out using various activated carbons prepared from sunflower seed hull (SSH), an agricultural solid waste by-product. The effect of parameters such as agitation time, initial dye concentration, adsorbent dosage, pH and temperature were studied. The Langmuir and Freundlich isotherm models were applied and the Langmuir model was found to best report the equilibrium isotherm data. Langmuir adsorption capacity was found to be 116.27 mg/g. Kinetic data followed pseudo-second-order kinetics. Maximum colour removal was observed at pH 2.0. It was observed that the rate of adsorption improves with increasing temperature and the process is endothermic. The adsorbent surface was analysed with a scanning electron microscope. The results indicate that activated sunflower seed hull could be an attractive option for colour removal from dilute industrial effluents.     

Adsorption of malachite green from aqueous solution onto carbon prepared from Arundo donax root

Arundo donax root carbon (ADRC), a new adsorbent, was prepared from Arundo donax root by carbonization. The surface area of the adsorbent was determined 158 m²/g by N₂ adsorption isotherm. Batch adsorption experiments were carried out for the removal of malachite green (MG) from aqueous solution using ADRC as adsorbent. The effects of various parameters such as solution pH (3–10), carbon dose (0.15–1.0 g/100 ml) and initial MG concentration (10–100 mg/l) on the adsorption system were investigated. The effective pH was 5–7 and the optimum adsorbent dose was found to be 0.6 g/100 ml. Equilibrium experimental data at 293, 303 and 313 K were better represented by Langmuir isotherm than Freundlich isotherm using linear and non-linear methods. Thermodynamic parameters such as ΔG, ΔH and ΔS were also calculated. The negative Gibbs free energy change and the positive enthalpy change indicated the spontaneous and endothermic nature of the adsorption. The adsorption equilibrium time was 180 min. Adsorption kinetics was determined using pseudo-first-order model, pseudo-second-order model and intraparticle diffusion model. The results showed that the adsorption of MG onto ADRC followed pseudo-second-order model.     

Removal of rhodamine B from aqueous solution by adsorption onto sodium montmorillonite

The adsorption of rhodamine B dye was carried out using sodium montmorillonite clay. The effect of parameters such as pH, adsorbent dosage and initial dye concentration was studied. The Langmuir and Freundlich isotherm models were applied and the Langmuir model was found to best fit the equilibrium isotherm data. Langmuir adsorption capacity was found to be 42.19 mg/g. Kinetic data followed pseudo-second-order kinetics. Maximum color removal was observed at pH 7.0. The ΔG° value was found to be negative, the adsorption process was feasible. The results indicate that sodium montmorillonite clay can be used for the removal of basic dyes from aqueous solutions.     

Adsorptive removal of acrylonitrile by commercial grade activated carbon: kinetics, equilibrium and thermodynamics

The potential of activated carbons--powdered (PAC) and granular (GAC), for the adsorption of acrylonitrile (AN) at different initial AN concentrations (50相似文献   

Biosorption of copper(II) by nonliving lichen biomass of Cladonia rangiformis hoffm

Biosorption of heavy metals can be an effective process for the removal of heavy metal ions from aqueous solutions. In this study, the adsorption properties of lichen biomass of Cladonia rangiformis hoffm. for copper(II) were investigated by using batch adsorption techniques. The effects of initial metal ion concentration, initial pH, biosorbent concentration, stirring speed and contact time on biosorption efficiency were studied. In the experiments the optimum pH value was found out 5.0 which was the native pH value of solution. The experimental adsorption data were fitted to the Langmuir adsorption model. The highest metal uptake was calculated from Langmuir isotherm and found to be 7.6923 mg Cu(II)/g inactivated lichen at 15 degrees C. The results indicated that the biomass of C. rangiformis is a suitable biosorbent for removing Cu(II) from aqueous solutions.     

Adsorption removal of cadmium and copper from aqueous solution by areca: a food waste

Areca waste (AW) has been investigated as metal biosorbent for cadmium and copper from aqueous solution for its availability as food waste and also for its cellulosic matrix rich of potential metal binding active sites. The effect of various parameters on adsorption process such as contact time, solution pH, amount of AW and initial concentration of metal ions was studied at room temperature to optimize the conditions for maximum adsorption. Maximum metal sorption was found to occur at pH 5.6. Adsorption process revealed that the initial uptake was rapid and equilibrium was established about in 1h for cadmium and copper. The equilibrium sorption data for single metal systems at pH 5.6 were described by the Langmuir, Freundlich and D-R isotherm models. The adsorption isotherm studies clearly indicated that the adsorptive behaviour of metal ions on AW not only the Langmuir assumptions but also the Freundlich and the D-R assumptions. The highest value of Langmuir maximum uptake, (b), was found for cadmium (1.12 mg/g) and copper (2.84 mg/g). Similar Freundlich empirical constants, K, were obtained for cadmium (1.086) and copper (1.119). Ion-exchange and surface adsorption might be involved in the adsorption process of cadmium and copper. Desorption studies revealed that cadmium and copper can be easily removed from AW by altering the pH values of the solution using HNO(3), indicating that AW are a promising adsorbent for wastewater treatment.     

Adsorption of copper ions onto microwave stabilized heavy metal sludge

Microwave stabilized heavy metal sludge was used as an adsorbent to remove the copper ions from aqueous solution. The adsorption characteristics of copper on the stabilized-sludge were studied by various models, such as Freundlich and Langmuir isotherm equation. Results show that the pH(zpc) of stabilized-sludge was at 9.2-9.5. Moreover, the adsorption of copper ions onto the stabilized-sludge surface was mainly on account of the heterogeneous surface of the stabilized-sludge. In the dynamic study, the experimental data was fitted to the intraparticle diffusion model, pseudo-first order model and pseudo-second order model. However, the experimental data was only well correlated with pseudo-second order model with the correlation coefficient>0.995. Furthermore, both Freundlich and Langmuir isotherm equations were found to represent the measured adsorption data well. From the Langmuir equation, the adsorption capacity increased from 18 to 28 mg/g as the temperature rose from 15 to 55 degrees C, since this adsorption process was an endothermic reaction. After this adsorption process, copper ions can be concentrated on and in a small bead and recovery efficiently.     

Characterizations of strontium(II) and barium(II) adsorption from aqueous solutions using dolomite powder

In this research, adsorption technique was applied for strontium and barium removal from aqueous solution using dolomite powder. The process has been investigated as a function of pH, contact time, temperature and adsorbate concentration. The experimental data was analyzed using equilibrium isotherm, kinetic and thermodynamic models. The isotherm data was well described by Langmuir isotherm model. The maximum adsorption capacity was found to be 1.172 and 3.958 mg/g for Sr(II) and Ba(II) from the Langmuir isotherm model at 293 K, respectively. The kinetic data was tested using first and pseudo-second order models. The results indicated that adsorption fitted well with the pseudo-second order kinetic model. The thermodynamic parameters (ΔG°, ΔH°, and ΔS°) were also determined using the equilibrium constant value obtained at different temperatures. The results showed that the adsorption for both ions was feasible and exothermic.     

Immobilization of 2,2'-dipyridyl onto bentonite and its adsorption behavior of copper(II) ions

In this study, the immobilization of 2,2'-dipyridyl onto bentonite was firstly carried out and it was then used for the adsorption of copper(II) ions from aqueous solutions. The variation of the parameters of pH, contact time, initial copper(II) concentration and temperature were investigated in the adsorption experiments. The XRD, FTIR, elemental and thermal analyses were performed to observe the immobilization of 2,2'-dipyridyl onto natural bentonite. The adsorption data obtained were well described by the Langmuir adsorption isotherm model at all studied temperatures. The results indicated that the maximum adsorption capacity was 54.07 mg g(-1) from the Langmuir isotherm model at 50 degrees C. The thermodynamic parameters indicated that the adsorption process is spontaneous, endothermic and chemical in nature. The kinetic parameters of the adsorption were calculated from the experimental data. According to these parameters, the best-fit was obtained by the pseudo-second-order kinetic model. The results showed that 2,2'-dipyridyl-immobilized bentonite can be used as the effective adsorbent for the removal of heavy metal contaminants.     

Chromium(VI) adsorption from aqueous solution by Hevea Brasilinesis sawdust activated carbon

Adsorption capacity of Cr(VI) onto Hevea Brasilinesis (Rubber wood) sawdust activated carbon was investigated in a batch system by considering the effects of various parameters like contact time, initial concentration, pH and temperature. Cr(VI) removal is pH dependent and found to be maximum at pH 2.0. Increases in adsorption capacity with increase in temperature indicate that the adsorption reaction is endothermic. Based on this study, the thermodynamic parameters like standard Gibb's free energy (DeltaG degrees ), standard enthalpy (DeltaH degrees ) and standard entropy (DeltaS degrees ) were evaluated. Adsorption kinetics of Cr(VI) ions onto rubber wood sawdust activated carbon were analyzed by pseudo first-order and pseudo second-order models. Pseudo second-order model was found to explain the kinetics of Cr(VI) adsorption most effectively. Intraparticle diffusion studies at different temperatures show that the mechanism of adsorption is mainly dependent on diffusion. The rate of intraparticle diffusion, film diffusion coefficient and pore diffusion coefficient at various temperatures were evaluated. The Langmuir, Freundlich and Temkin isotherm were used to describe the adsorption equilibrium studies of rubber wood sawdust activated carbon at different temperatures. Langmuir isotherm shows better fit than Freundlich and Temkin isotherm in the temperature range studied. The result shows that the rubber wood sawdust activated carbon can be efficiently used for the treatment of wastewaters containing chromium as a low cost alternative compared to commercial activated carbon and other adsorbents reported.     

Comparison of the efficiency of palladium and silver nanoparticles loaded on activated carbon and zinc oxide nanorods loaded on activated carbon as new adsorbents for removal of Congo red from aqueous solution: Kinetic and isotherm study

The adsorption of Congo red (CR) into three new adsorbents including Palladium and silver nanoparticles loaded on activated carbon (Pd NPs-AC, Ag NPs-AC) and zinc oxide nanorods loaded on activated carbon (ZnO-NRs-AC) in a batch method has been studied following the optimization of effective variables including pH, amount of adsorbents and time. The experimental data was fitted to conventional kinetic models including the pseudo first-order and second-order Elovich and intraparticle diffusion model and based on calculated respective parameters such as rate constants, equilibrium adsorption capacities and correlation coefficients. It was found that for all adsorbents the removal process follows the pseudo second other kinetic model with involvement of interparticle diffusion model. The experimental isotherm data were analyzed using the Langmuir, Freundlich, Tempkin and Dubinin and Radushkevich equations and it was found for all adsorbents that the removal process followed the Langmuir isotherm.     

Equilibrium and kinetic mechanism for Reactive Black 5 sorption onto high lime Soma fly ash

Batch adsorption studies were carried out for the sorption of C.I. Reactive Black 5, a reactive dye, onto high lime fly ash, obtained from Soma Thermal Power Plant (Turkey), to be low cost adsorbent. The effect of various experimental parameters such as contact time, adsorbent dose and initial dye concentration were investigated. Determination of the adsorption equilibrium concentrations was determined by UV-vis spectrophotometry analytical method. Equilibrium data were fitted to the Freundlich and Langmuir isotherm equations and the equilibrium data were found to be well represented by the Freundlich isotherm equation. The adsorption kinetics of C.I. Reactive Black 5 onto high lime fly ash were also studied to characterize of the surface complexation reaction. A pseudo-second-order mechanism has been developed to predict the rate constant of the adsorption, the equilibrium capacity and initial adsorption rate with the effect of initial concentration. A single-stage batch adsorber design of the adsorption of C.I. Reactive Black 5 onto high lime fly ash has been studied based on the Freundlich isotherm equation.     

Equilibrium studies for trimethoprim adsorption on montmorillonite KSF

In this study, the adsorption of trimethoprim (TMP) on montmorillonite KSF was studied under different conditions (pH, ionic strength, temperature). The results indicate that a pH value of 5.04 is optimum value for the adsorption of TMP on KSF. The adsorption kinetics was interpreted using pseudo-first-order kinetic model, pseudo-second-order kinetic model and intraparticle diffusion model. The pseudo-second-order model provides the best correlation with the experimental data of KSF adsorption. The adsorption data could be fitted with Freundlich, Langmuir and Dubinin-Radushkevich equation to find the characteristic parameters of each model. It was found that linear form of Langmuir isotherm seems to produce a better model than linear form of Freundlich equation. From the Langmuir and Freundlich equation, the adsorption capacity values raised as the solution temperature decreased. From DR isotherm, it was also determined that the type of adsorption can be considered as ion-exchange mechanism. Determination of the thermodynamic parameters DeltaH(0), DeltaS(0) and DeltaG(0) showed that adsorption was spontaneous and exothermic in nature. It was also added that adsorption of TMP by KSF may involve physical adsorption.     

Removal of Pb(II) ions from aqueous solutions by sulphuric acid-treated wheat bran

Sulphuric acid-treated wheat bran (STWB) was used as an adsorbent to remove Pb(II) ions from aqueous solution. It was observed that the adsorption yield of Pb(II) ions was found to be pH dependent. The equilibrium time for the process was determined as 2h. STWB gave the highest adsorption yield at around pH 6.0. At this pH, adsorption percentage for an initial Pb(II) ions concentration of 100mg/L was found to be 82.8 at 25 degrees C for contact time of 2h. The equilibrium data obtained at different temperatures fitted to the non-linear form of Langmuir, Freundlich and Redlich-Peterson and linear form of Langmuir and Freundlich models. Isotherm constants were calculated and compared for the models used. The maximum adsorption capacity (q(max)) which was obtained linear form of Langmuir model increased from 55.56 to 79.37mg/g with increasing temperature from 25 to 60 degrees C. Similar trend was observed for other isotherm constants related to the adsorption capacity. Linear form of Langmuir isotherm data was evaluated to determine the thermodynamic parameters for the process. Thermodynamic parameters show that adsorption process of Pb(II) ions is an endothermic and more effective process at high temperatures. The pseudo nth order kinetic model was successfully applied to the kinetic data and the order (n) of adsorption reaction was calculated at the range from 1.711 to 1.929. The values of k(ad) were found to be 5.82x10(-4) and 21.81x10(-4)(min(-1))(mg/g)(1-n) at 25 and 60 degrees C, respectively. Activation energy was determined as 29.65kJ/mol for the process. This suggest that the adsorption Pb(II) ions by STWB is chemically controlled.