Self-assembled monolayers (SAMs) of cobalt tetracarboxylic acidchloride phthalocyanine covalently attached onto a preformed mercaptoethanol SAM: A novel method

A feasible method of fabricating phthalocyanine sensor was developed by covalent attachment of cobalt tetracarboxylic acidchloride phthalocyanine (CoTCACIPc) onto a preformed 2-mercaptoethanol (2-ME) self-assembled monolayer (SAM) modified gold electrode (designated as CoTCACIPc-2-ME-SAM). The surface concentration of the CoTCACIPc was found to be 4.58 × 10⁻¹⁰ mol/cm². The sensor gave a linear response to l-cysteine over the concentration range 0.28-20 μM with a detection limit of 5 × 10⁻⁷ M and best response time of 2 s.     

An unusual H2O2 electrochemical sensor based on Ni(OH)2 nanoplates grown on Cu substrate

In this work, Ni(OH)₂ nanoplates grown on the Cu substrate were synthesized and characterized by scanning electron microscopy (SEM), X-ray powder diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Then a novel Cu-Ni(OH)₂ modified glass carbon electrode (Cu-Ni(OH)₂/GCE) was fabricated and evaluated by electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), and typical amperometric response (i-t) method. Exhilaratingly, the Cu-Ni(OH)₂/GCE shows significant electrocatalytic activity toward the reduction of H₂O₂. At an applied potential of −0.1 V, the sensor produces an ultrahigh sensitivity of 408.1 μA mM⁻¹ with a low detection limit of 1.5 μM (S/N = 3). The response time of the proposed electrode was less than 5 s. What's more, the proposed sensor displays excellent selectivity, good stability, and satisfying repeatability.     

Fabrication of graphene/prussian blue composite nanosheets and their electrocatalytic reduction of H2O2

In this work, graphene/prussian blue (PB) composite nanosheets with good dispersibility in aqueous solutions have been synthesized by mixing ferric-(III) chloride and potassium ferricyanide in the presence of graphene under ambient conditions. Transmission electron microscopy (TEM) shows that the average size of the as-synthesized PB nanoparticles on the surface of graphene nanosheets is about 20 nm. Fourier-transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD) patterns have been used to characterize the chemical composition of the obtained graphene/PB composite nanosheets. The graphene/PB composite nanosheets exhibit good electrocatalytic behavior to detection of H₂O₂ at an applied potential of −0.05 V. The sensor shows a good linear dependence on H₂O₂ concentration in the range of 0.02-0.2 mM with a sensitivity of 196.6 μA mM⁻¹ cm⁻². The detection limit is 1.9 μM at the signal-to-noise ratio of 3. Furthermore, the graphene/PB modified electrode exhibits freedom of interference from other co-existing electroactive species. This work provides a new kind of composite modified electrode for amperometric biosensors.     

Novel amperometric glucose biosensor based on an ether-linked cobalt(II) phthalocyanine-cobalt(II) tetraphenylporphyrin pentamer as a redox mediator

The development of cobalt(II) phthalocyanine-cobalt(II) tetra(5-phenoxy-10,15,20-triphenylporphyrin), (CoPc-(CoTPP)₄) pentamer as a novel redox mediator for amperometric enzyme electrode sensitive to glucose is described. A glassy carbon electrode (GCE) was first modified with the pentamer, then followed by the immobilization onto the GCE-CoPc-(CoTPP)₄ with glucose oxidase (GOx) through cross-linking with glutaraldehyde in the presence of bovine serum albumin (BSA) and Nafion^® cation-exchange polymer. The proposed biosensor displayed good amperometric respose charateristics to glucose in pH 7.0 PBS solution; such as low overpotentials (+400 mV versus Ag|AgCl), very fast amperometric response time (∼5 s), linear concentration range extended up to 11 mM, with 10 μM detection limit. The biosensor exhibited electrochemical Michaelis-Menten kinetics and showed an average apparent Michaelis-Menten constant (K^′M) of 14.91 ± 0.46 mM over a storage period of 2 weeks.     

Direct electrochemistry of glucose oxidase assembled on graphene and application to glucose detection

The direct electrochemistry of glucose oxidase (GOx) integrated with graphene was investigated. The voltammetric results indicated that GOx assembled on graphene retained its native structure and bioactivity, exhibited a surface-confined process, and underwent effective direct electron transfer (DET) reaction with an apparent rate constant (k_s) of 2.68 s⁻¹. This work also developed a novel approach for glucose detection based on the electrocatalytic reduction of oxygen at the GOx-graphene/GC electrode. The assembled GOx could electrocatalyze the reduction of dissolved oxygen. Upon the addition of glucose, the reduction current decreased, which could be used for glucose detection with a high sensitivity (ca. 110 ± 3 μA mM⁻¹ cm⁻²), a wide linear range (0.1-10 mM), and a low detection limit (10 ± 2 μM). The developed approach can efficiently exclude the interference of commonly coexisting electroactive species due to the use of a low detection potential (−470 mV, versus SCE). Therefore, this study has not only successfully achieved DET reaction of GOx assembled on graphene, but also established a novel approach for glucose detection and provided a general route for fabricating graphene-based biosensing platform via assembling enzymes/proteins on graphene surface.     

Gold nanoparticles mediate the assembly of manganese dioxide nanoparticles for H2O2 amperometric sensing

Aggregates of gold nanoparticles (AuNPs) that mediate the assembly of manganese dioxide nanoparticles (nano-MnO₂) for hydrogen peroxide (H₂O₂) amperometric sensing have been developed. The aggregates were prepared by directly mixing citric-capped AuNPs and poly(allylamine hydrochloride) (PAH)-capped nano-MnO₂ using an electrostatic self-assembly strategy. The prepared sensor exhibited excellent electrochemical behaviors and a wide linear range from 7.80 × 10⁻⁷ to 8.36 × 10⁻⁴ M with a detection limit of 4.68 × 10⁻⁸ M (S/N = 3) because of the synergistic influence of excellent catalytic ability of MnO₂ and good electrical conductivity of AuNPs. In addition, its applicability to practical samples for measuring H₂O₂ in toothpastes has obtained a satisfactory result. Due to the ease of preparation and excellent properties of the sensor, indicating the MnO₂-AuNP material may be a potential H₂O₂ sensor.     

A new amperometric glucose biosensor based on platinum nanoparticles/polymerized ionic liquid-carbon nanotubes nanocomposites

A new amperometric glucose biosensor has been developed based on platinum (Pt) nanoparticles/polymerized ionic liquid-carbon nanotubes (CNTs) nanocomposites (PtNPs/PIL-CNTs). The CNTs was functionalized with polymerized ionic liquid (PIL) through directly polymerization of the ionic liquid, 1-vinyl-3-ethylimidazolium tetrafluoroborate ([VEIM]BF₄), on carbon nanotubes and then used as the support for the highly dispersed Pt nanoparticles. The electrochemical performance of the PtNPs/PIL-CNTs modified glassy carbon (PtNPs/PIL-CNTs/GC) electrode has been investigated by typical electrochemical methods. The PtNPs/PIL-CNTs/GC electrode shows high electrocatalytic activity towards the oxidation of hydrogen peroxide. Taking glucose oxidase (GOD) as the model, the resulting amperometric glucose biosensor shows good analytical characteristics, such as a high sensitivity (28.28 μA mM⁻¹ cm⁻²), wide linear range (up to 12 mM) and low detection limit (10 μM).     

Modification of glassy carbon electrode with multi-walled carbon nanotubes and iron(III)-porphyrin film: Application to chlorate, bromate and iodate detection

In this study, multi-wall carbon nanotubes (MWCTs) is evaluated as a transducer, stabilizer and immobilization matrix for the construction of amperometric sensor based on iron-porphyrin. 5,10,15,20-Tetraphenyl-21H,23H-porphine iron(III) chloride (Fe(III)P) adsorbed on MWCNTs immobilized on the surface of glassy carbon electrode. Cyclic voltammograms of the Fe(III)P-incorporated-MWCNTs indicate a pair of well-defined and nearly reversible redox couple with surface confined characteristics at wide pH range (2-12). The surface coverage (Γ) and charge transfer rate constant (k_s) of Fe(III)P immobilized on MWCNTs were 7.68 × 10⁻⁹ mol cm⁻² and 1.8 s⁻¹, respectively, indicating high loading ability of MWCNTs for Fe(III)P and great facilitation of the electron transfer between Fe(III)P and carbon nanotubes immobilized on the electrode surface. Modified electrodes exhibit excellent electrocatalytic activity toward reduction of ClO₃⁻, IO₃⁻ and BrO₃⁻ in acidic solutions. The catalytic rate constants for catalytic reduction of bromate, chlorate and iodate were 6.8 × 10³, 7.4 × 10³ and 4.8 × 10² M⁻¹ s⁻¹, respectively. The hydrodynamic amperometry of rotating-modified electrode at constant potential versus reference electrode was used for detection of bromate, chlorate and iodate. The detection limit, linear calibration range and sensitivity for chlorate, bromate and iodate detections were 0.5 μM, 2 μM to 1 mM, 8.4 nA/μM, 0.6 μM, 2 μM to 0.15 mM, 11 nA/μM, and 2.5 μM, 10 μM to 4 mM and 1.5 nA/μM, respectively. Excellent electrochemical reversibility of the redox couple, good reproducibility, high stability, low detection limit, long life time, fast amperometric response time, wide linear concentration range, technical simplicity and possibility of rapid preparation are great advantages of this sensor. The obtained results show promising practical application of the Fe(III)P-MWCNTs-modified electrode as an amperometric sensor for chlorate, iodate and bromate detections.     

Electrochemical synthesis of WO3/PANI composite for electrocatalytic reduction of iodate

Composite film of polyaniline (PANI) and tungsten oxide (WO₃) was electrodeposited by cyclic voltammetric technique from a solution of aniline and tungstic acid. The obtained WO₃/PANI film displayed a significant enhancement of electrocatalytic activity for iodate reduction and a better stability than that of pure WO₃ and PANI films. Result of amperometric experiment revealed a good linear relationship with concentration of IO₃⁻ from 20 to 500 μM, with a high sensitivity of 0.54 μA/μM and a detection limit of 2.7 μM for the determination of iodate. This composite film was also successfully applied in determination of iodate in commercial table salt.     

Iron-enriched natural zeolite modified carbon paste electrode for H2O2 detection

This work demonstrates that iron-enriched natural zeolitic volcanic tuff (Paglisa deposit, Cluj county, Transilvania, Romania) resulting from a previous use as adsorbent in wastewater treatment can be recycled into effective electrode modifier applied to the electrocatalytic detection of hydrogen peroxide. After physico-chemical characterization of tuff samples using various techniques such as chemical analysis, X-ray diffraction, scanning electron microscopy, infrared spectroscopy, BET analysis and X-ray photoelectron spectroscopy, the electrochemical response of the iron-enriched zeolites was studied on the basis of solid carbon paste electrodes modified with these samples. The results indicate that iron centers in the zeolite are electroactive and that they act as electrocatalysts in the voltammetric and amperometric detection of H₂O₂. Best performance was achieved in phosphate buffer at pH 7, showing a sensitivity of 0.57 mA M⁻¹ cm⁻², a detection limit down to 60 μM, and a linear domain up to 100 mM H₂O₂.     

Functionalized carbon nanotube-bienzyme biocomposite for amperometric sensing

An approach to design a biocomposite bienzyme biosensor with the aim of evaluating its suitability as an amperometric sensor using functionalized multiwalled carbon nanotubes (MWCNTs) is presented. The biosensor is based on a bienzyme-channelling configuration, employing the enzymes glucose oxidase (GOx) and horseradish peroxidase (HRP), which were immobilized with toluidine blue (TB) functionalized MWCNTs. The proposed method demonstrates an easy electron transfer between the immobilized enzymes and the electrode via functionalized MWCNTs in a Nafion matrix. Co-immobilization of GOx and HRP was employed to establish the feasibility of fabricating highly effective bienzyme-based biosensors for low-level glucose determination. Bienzyme immobilized TB functionalized MWCNTs were attached to a glassy carbon electrode, and the electrochemical behavior of the sensor was studied using electrochemical impedance spectroscopy, cyclic voltammetry and chronoamperometry. The excellent electrocatalytic activity of the biocomposite film resulted in the detection of glucose under reduced over potential with a wider range of determination from 1.5 × 10⁻⁸ M to 1.8 × 10⁻³ M and with a detection limit of 3 × 10⁻⁹ M. The sensor showed a short response time (within 2 s), good stability and anti-interferant ability. The proposed biosensor exhibits good analytical performance in terms of repeatability, reproducibility and shelf-life stability.     

A sensitive amperometric bromate sensor based on multi-walled carbon nanotubes/phosphomolybdic acid composite film

An amperometric sensor for bromate was developed based on multi-walled carbon nanotubes (MWNTs)/phosphomolybdic acid (PMo₁₂) composite film coated on a pyrolytic graphite (PG) electrode. MWNTs are dispersed in PMo₁₂ aqueous solution through spontaneous and strong chemisorption between carbon and polyoxometalate, which results in a homogeneous MWNTs/PMo₁₂ composite. Due to the unique electronic and electrocatalytic properties of MWNTs and PMo₁₂, the combination of MWNTs and PMo₁₂ results in a remarkable synergistic augmentation on the response current. The bromate sensor based on the PG/MWNTs/PMo₁₂ electrode has excellent characteristics, such as a detection limit of 0.5 μM, a sensitivity of 760.9 μA mM⁻¹ cm⁻², a response time less than 2 s and a linear range from 5 μM to 15 mM.     

Electrochemical tolazoline sensor based on gold nanoparticles and imprinted poly-o-aminothiophenol film

Amperometric detection of tolazoline (TL) was carried out on a gold nanoparticles (AuNPs)/poly-o-aminothiophenol (PoAT)-modified electrode by a molecular imprinting technique and electropolymerization method. The modification procedure was characterized via electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The recognition between the imprinted sensor and target molecule was observed by measuring the variation of amperometric response of the oxidation-reduction probe, K₃Fe(CN)₆ on electrode. Under the optimal experimental conditions, the peak currents were proportional to the concentrations of tolazoline in two ranges of 0.05-5.0 μg mL⁻¹ and 5.0-240 μg mL⁻¹ with the detection limit of 0.016 μg mL⁻¹. Meanwhile the prepared sensor showed sensitive and selective binding sites for tolazoline. The enhancement of sensitivity was attributed to the presence of AuNPs which decreased the electron-transfer impedance.     

Towards the conception of an amperometric sensor of l-tyrosine based on Hemin/PAMAM/MWCNT modified glassy carbon electrode

A novel amperometric sensor was fabricated based on the immobilization of hemin onto the poly (amidoamine)/multi-walled carbon nanotube (PAMAM/MWCNT) nanocomposite film modified glassy carbon electrode (GCE). Electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) and ultraviolet visible (UV-vis) adsorption spectroscopy were used to investigate the possible state and electrochemical activity of the immobilized hemin. In the Hemin/PAMAM/MWCNT nanocomposite film, MWCNT layer possessed excellent inherent conductivity to enhance the electron transfer rate, while the layer of PAMAM greatly enlarged the surface average concentration of hemin (Γ) on the modified electrode. Therefore, the nanocomposite film showed enhanced electrocatalytical activity towards the oxidation of l-tyrosine. The kinetic parameters of the modified electrode were investigated. In pH 7.0 phosphate buffer solution (PBS), the sensor exhibits a wide linear range from 0.1 μM to 28.8 μM l-tyrosine with a detection limit of 0.01 μM and a high sensitivity of 0.31 μA μM⁻¹ cm⁻². In addition, the response time of the l-tyrosine sensor is less than 5 s. The excellent performance of the sensor is largely attributed to the electro-generated high reactive oxoiron (IV) porphyrin (O = Fe^IV-P) which effectively catalyzed the oxidation of l-tyrosine. A mechanism was herein proposed for the catalytic oxidation of l-tyrosine by oxoiron (IV) porphyrin complexes.     

Flow injection amperometric determination of pyridoxine at a Prussian blue nanoparticle-modified carbon ceramic electrode

This work describes the electrocatalytic properties of a carbon composite electrode (CCE) modified with Prussian blue (PB) nanoparticles (NPs) for the electrocatalytic oxidation of pyridoxine (PN). The morphology of the PBNP-modified CCE was characterized by scanning electron microscopy (SEM). The mechanism and kinetics of the catalytic oxidation reaction of PN were monitored by cyclic voltammetry and chronoamperometry. The rate-limiting step of the charge transfer reaction was found to be a one-electron abstraction. The value of α, k, and D were calculated as 0.66, 6.7 × 10⁴ M⁻¹ s⁻¹, and 1.88 × 10⁻⁵ cm² s⁻¹, respectively. The modified electrode showed electrocatalytic activity toward the oxidation of PN and was used as an amperometric sensor. The sensor exhibited good linear response for PN over the concentration ranges 5-69 and 1-80 μM with detection limits of 0.51 and 0.87 μM, and sensitivities of 0.97 and 0.673 A M⁻¹ cm⁻² in batch and flow conditions, respectively. Some important advantages such as simple preparation, fast response, good stability, and reproducibility of the sensor for the amperometric determination of PN were achieved.     

Direct electron-transfer and electrochemical catalysis of hemoglobin immobilized on mesoporous Al2O3

The direct electrochemistry of hemoglobin (Hb) has been achieved by immobilizing Hb on mesoporous Al₂O₃ (meso-Al₂O₃) film modified glassy carbon (GC) electrode. Meso-Al₂O₃ shows significant promotion to the direct electron-transfer of Hb, thus it exhibits a pair of well defined and quasi-reversible peaks with a formal potential of −0.345 V (vs. SCE). The electron-transfer rate constant (k_s) is estimated to be 3.17 s⁻¹. The immobilized Hb retains its biological activity well and shows high catalytic activity to the reduction of hydrogen peroxide (H₂O₂) and nitrite (NO₂⁻). Under the optimized experimental conditions, the catalytic currents are linear to the concentrations of H₂O₂ and NO₂⁻ in the ranges of 0.195-20.5 μM and 0.2-10 mM, respectively. The corresponding detection limits are 1.95 × 10⁻⁸ M and 3 × 10⁻⁵ M (S/N = 3). The resulting protein electrode has high thermal stability and good reproducibility due to the protection effect of meso-Al₂O₃. Ultraviolet visible (UV-vis) absorption spectra and reflection-absorption infrared (RAIR) spectra display that Hb keeps almost natural structure in the meso-Al₂O₃ film. The N₂ adsorption-desorption experiments show that the pore size of meso-Al₂O₃ is about 14.4 nm, suiting for the encapsulation of Hb (average size: 5.5 nm) well. Therefore, meso-Al₂O₃ is an alternative matrix for protein immobilization and biosensor preparation.     

Glucose biosensor based on multiwalled carbon nanotubes grown directly on Si

An amperometric biosensor based on covalent immobilization of glucose oxidase (GOx) on multiwalled carbon nanotubes (MWCNTs) with potassium ferricyanide as the redox mediator was developed. The MWCNTs were grown directly on a layered structure of Co/Ti/Cr on a SiO₂/Si substrate by microwave-heated chemical vapor deposition. The mediator helps to shuttle the electrons between the immobilized GOx and the MWCNT electrode, therefore operating at a potential of 0.25 V vs. the saturated calomel electrode. This potential precludes the interfering compounds from oxidization. The sensitivity of biosensors to glucose was found to depend on the acid pretreatment and GOx reaction times. The steady-state response of the optimized biosensor exhibits a sensitivity of 20.6 μA mM⁻¹ cm⁻², a linear range of up to 8 mM, and a response time of <5 s.     

Neodymium (III) hexacyanoferrate (II) nanoparticles induced by enzymatic reaction and their use in biosensing of glucose

The formation of neodymium (III) hexacyanoferrate (II) (NdHCF) nanoparticles (NPs) on the surface of carbon-paste electrode induced by enzymatic reaction was described and characterized. The conditions for biosensing of glucose were optimized through various experiments. Results showed that the optimized condition of the glucose oxidase (GOx)-induced NdHCF NPs for the biosensing of glucose were 2.0 mM Nd³⁺, 40.0 mM Fe(CN)₆³⁻ and 20 μg/mL GOx. The biocatalyzed generation of NdHCF NPs in the presence of O₂/glucose and GOx enabled the development of an electrochemical biosensor for glucose. Furthermore, this system avoids the interferences from other species for the biosensing of glucose.     

Surface chemistry and electrocatalytic behaviour of tetra-carboxy substituted iron, cobalt and manganese phthalocyanine monolayers on gold electrode

Surface chemistry and electrocatalytic properties of self-assembled monolayers of metal tetra-carboxylic acid phthalocyanine complexes with cobalt (Co), iron (Fe) and manganese (Mn) as central metal ions have been studied. These phthalocyanine molecules are immobilized on gold electrode via the coupling reaction between the ring substituents and pre-formed mercaptoethanol self-assembled monolayer (Au-ME SAM). X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy confirmed chemisorption of mercaptoethanol via sulfur group on gold electrode and also coupling reaction between phthalocyanines and Au-ME SAM. Electrochemical parameters of the immobilized molecules show that these molecules are densely packed with a perpendicular orientation. The potential applications of the gold modified electrodes were investigated towards l-cysteine detection and the analysis at phthalocyanine SAMs. Cobalt and iron tetra-carboxylic acid phthalocyanine monolayers showed good oxidation peak for l-cysteine at potentials where metal oxidation (M^III/M^II) takes place and this metal oxidation mediates the catalytic oxidation of l-cysteine. Manganese tetra-carboxylic acid phthalocyanine monolayer also exhibited a good catalytic oxidation peak towards l-cysteine at potentials where Mn^IV/Mn^III redox peak occurs and this redox peak mediates l-cysteine oxidation. The analysis of cysteine at phthalocyanine monolayers displayed good analytical parameters with good detection limits of the orders of 10⁻⁷ mol L⁻¹ and good linearity for a studied concentration range up to 60 μmol L⁻¹.     

Facile direct electron transfer in glucose oxidase modified electrodes

Glucose oxidase (GOx) is widely used in the glucose biosensor industry. However, mediatorless direct electron transfer (DET) from GOx to electrode surfaces is very slow. Recently, mediatorless DET has been reported via the incorporation of nanomaterials such as carbon nanotubes and nanoparticles in the modification of electrodes. Here we report GOx electrodes showing DET without the need for any nanomaterials. The enzyme after immobilization with poly-l-lysine (PLL) and Nafion^® retains the biocatalytic activities and oxidizes glucose efficiently. The amperometric response of Nafion-PLL-GOx modified electrode is linearly proportional to the concentration of glucose up to 10 mM with a sensitivity of 0.75 μA/mM at a low detection potential (−0.460 V vs. Ag/AgCl). The methodology developed in this study will have impact on glucose biosensors and biofuel cells and may potentially simplify enzyme immobilization in other biosensing systems.