Quantitative Analysis of Bulk Heterojunction Films Using Linear Absorption Spectroscopy and Solar Cell Performance

A fundamental understanding of the relationship between the bulk morphology and device performance is required for the further development of bulk heterojunction organic solar cells. Here, non‐optimized (chloroform cast) and nearly optimized (solvent‐annealed o‐dichlorobenzene cast) P3HT:PCBM blend films treated over a range of annealing temperatures are studied via optical and photovoltaic device measurements. Parameters related to the P3HT aggregate morphology in the blend are obtained through a recently established analytical model developed by F. C. Spano for the absorption of weakly interacting H‐aggregates. Thermally induced changes are related to the glass transition range of the blend. In the chloroform prepared devices, the improvement in device efficiency upon annealing within the glass transition range can be attributed to the growth of P3HT aggregates, an overall increase in the percentage of chain crystallinity, and a concurrent increase in the hole mobilities. Films treated above the glass transition range show an increase in efficiency and fill factor not only associated with the change in chain crystallinity, but also with a decrease in the energetic disorder. On the other hand, the properties of the P3HT phase in the solvent‐annealed o‐dichlorobenzene cast blends are almost indistinguishable from those of the corresponding pristine P3HT layer and are only weakly affected by thermal annealing. Apparently, slow drying of the blend allows the P3HT chains to crystallize into large domains with low degrees of intra‐ and interchain disorder. This morphology appears to be most favorable for the efficient generation and extraction of charges.     

Difluorobenzothiadiazole‐Based Small‐Molecule Organic Solar Cells with 8.7% Efficiency by Tuning of π‐Conjugated Spacers and Solvent Vapor Annealing

The synthesis of a series of tetrafluorine‐substituted, wide‐bandgap, small molecules consisting of various π‐conjugated spacers (furan, thiophene, selenophene) between indacenodithiophene as the electron‐donating core and the electron‐deficient difluorobenzothiadiazole unit is reported and the effect of the π‐conjugated spacers on the photovoltaic properties is investigated. The alteration of the π‐conjugated spacer enables fine‐tuning of the photophysical properties and energy levels of the small molecules, and allows the adjustment of the charge‐transport properties, the morphology of the photoactive films, as well as their photovoltaic properties. Moreover, most of these devices exhibit superior device performances after CH₂Cl₂ solvent annealing than without annealing, with a high fill factor (0.70–0.75 for all cases). Notably, the devices based on the new molecule BIT4FTh (with thiophene as the spacer) show an outstanding PCE of 8.7% (with an impressive FF of 0.75), considering its wide‐bandgap (1.81 eV), which is among the highest efficiencies reported so far for small‐molecules‐based solar cells. The morphologies of the photoactive layers with/without CH₂Cl₂ solvent annealing are characterized by atomic force microscopy, transmission electron microscopy and two‐dimensional grazing incidence X‐ray diffraction analysis. The results reported here clearly indicate that highly efficient small‐molecules‐based solar cells can be achieved through rational design of their molecular structure and optimization of the phase‐separated morphology via an adapted solvent–vapor annealing process.     

Efficiency Enhanced Hybrid Solar Cells Using a Blend of Quantum Dots and Nanorods

The cell performance of organic‐inorganic hybrid photovoltaic devices based on CdSe nanocrystals and the semiconducting polymer poly[2,6‐(4,4‐bis(2‐ethylhexyl)‐4H‐cyclopenta[2,1‐b;3,4‐b′]‐dithiophene)‐alt‐4,7‐(2,1,3‐benzothiadiazole)] (PCPDTBT) is strongly dependent on the applied polymer‐to‐nanocrystal loading ratio and the annealing temperature. It is shown here that higher temperatures for the thermal annealing step have a beneficial impact on the nanocrystal phase by forming extended agglomerates necessary for electron percolation to enhance the short‐circuit current. However, there is a concomitant reduction of the open‐circuit voltage, which arises from energy‐level alterations of the organic and the inorganic component. Based on quantum dots and PCPDTBT, we present an optimized organic–inorganic hybrid system utilizing an annealing temperature of 210 °C, which provides a maximum power conversion efficiency of 2.8%. Further improvement is obtained by blending nanocrystals of two different shapes to compose a favorable n‐type network. The blend of spherical quantum dots and elongated nanorods results in a well‐interconnected pathway for electrons within the p‐type polmer matrix, yielding maximum efficiencies of 3.6% under simulated AM 1.5 illumination.     

Formation of Well‐Ordered Heterojunctions in Polymer:PCBM Photovoltaic Devices

The nanoscale morphology in polymer:PCBM based photovoltaic devices is a major contributor to overall device performance. The disordered nature of the phase‐separated structure, in combination with the small length scales involved and the inherent difficulty of reproducing the exact morphologies when spin‐coating and annealing thin blend films, have greatly hampered the development of a detailed understanding of how morphology impacts photo­voltaic device functioning. In this paper we demonstrate a double nano­imprinting process that allows the formation of nanostructured polymer:PCBM heterojunctions of composition and morphology that can be selected independently. We fabricated photovoltaic (PV) devices with extremely high densities (10¹⁴ mm^?2) of interpenetrating nanoscale columnar features (as small as 25 nm; at or below the exciton diffusion length) in the active layer. By comparing device results of different feature sizes and two different polymer:PCBM combinations, we demonstrate how double imprinting can be a powerful tool to systematically study different parameters in polymer photovoltaic devices.     

Investigating Morphology and Stability of Fac‐tris (2‐phenylpyridyl)iridium(III) Films for OLEDs

Stable film morphology is critical for long‐term high performance organic light‐emitting diodes (OLEDs). Neutron reflectometry (NR) is used to study the out‐of‐plane structure of blended thin films and multilayer structures comprising evaporated small molecules. It is found that as‐prepared blended films of fac‐tris(2‐phenylpyridyl)iridium(III) [Ir(ppy)₃] in 4,4′‐bis(N‐carbazolyl)biphenyl (CBP) are uniformly mixed, but the occurrence of phase separation upon thermal annealing is dependent on the blend ratio. Films comprised of the ratio of 6 wt% of Ir(ppy)₃ in CBP typically used in OLEDs are found to phase separate with moderate heating while a higher weight percent mixture (12 wt%) is found to be stable. Furthermore, it is found that thermal annealing of a multilayer film comprised of typical layers found in efficient devices ([tris(4‐carbazoyl‐9‐ylphenyl)amine (TCTA)/Ir(ppy)₃:CBP/bathocuproine (BCP)]) causes the BCP layer to become mixed with the emissive blend layer, whereas the TCTA interface remains unchanged. This significant structural change causes no appreciable difference in the photo­luminescence of the stack although such a change would have a dramatic effect on the charge transport through the device, leading to changes in performance. These results demonstrate the effect of thermal stress on the delicate interplay between the chemical composition and morphology of OLED films.     

Correlating the Molecular Structure of A-DA′D-A Type Non-Fullerene Acceptors to Its Heat Transfer and Charge Transport Properties in Organic Solar Cells

Efficient heat transfer is beneficial to heat dissipation and the thermal durability of organic solar cell (OSCs). In this regard, heat transfer properties of organic semiconductors within OSCs should play important roles, but their thermal properties are rarely explored. Here, heat diffusion properties of Y-series non-fullerene acceptors processing different DA′D framework, named BZ4F-5, BZ4F-6, and BZ4F-7 are probed; it is found that backbone rings extension from five- to six- and seven-membered-fused rings trigger longer phonon mean free path and higher thermal diffusivities (D) in their pristine solid films and bulk heterojunction blends. Particularly, the correlation between the thermal transport properties in Y-series acceptors and their backbone geometry, molecule stacking, and thin-film crystallinity is demonstrated. More importantly, both organic thin-film transistors and OSCs confirm that thermal durability of organic semiconductor devices correlated with the thermal properties of their active layer. Although BZ5F-6 and BZ4F-7 based devices possess similar device performance at room temperature, superior heat dissipation in BZ4F-7 molecule endows it with enhanced device lifetime. These results contribute to critical design criteria for future molecular optimization in photovoltaic and optoelectronic devices.     

The Role of Morphology in Optically Switchable Transistors Based on a Photochromic Molecule/p‐Type Polymer Semiconductor Blend

The correlation between morphology and optoelectronic performance in organic thin‐film transistors based on blends of photochromic diarylethenes (DAE) and poly(3‐hexylthiophene) (P3HT) is investigated by varying molecular weight (M_w = 20–100 kDa) and regioregularity of the conjugated polymer as well as the temperature of thermal annealing (rt‐160 °C) in thin films. Semicrystalline architectures of P3HT/DAE blends comprise crystalline domains, ensuring efficient charge transport, and less aggregated regions, where DAEs are located as a result of their spontaneous expulsion from the crystalline domains during the self‐assembly. The best compromise between field‐effect mobility (μ) and switching capabilities is observed in blends containing P3HT with M_w = 50 kDa, exhibiting μ as high as 1 × 10^?3 cm² V^?1 s^?1 combined with a >50% photoswitching ratio. Higher or lower M_w than 50 kDa are found to be detrimental for field‐effect mobility and to lead to reduced device current switchability. The microstructure of the regioregular P3HT blend is found to be sensitive to the thermal annealing temperature, with an increase in μ and a decrease in current modulation being observed as a response to the light‐stimulus likely due to an increased P3HT‐DAE segregation, partially hindering DAE photoisomerization. The findings demonstrate the paramount importance of fine tuning the structure and morphology of bicomponent films for leveraging the multifunctional nature of optoelectronic devices.     

Monitoring the Formation of a CH3NH3PbI3–xClx Perovskite during Thermal Annealing Using X‐Ray Scattering

Grazing incidence wide and small angle X‐ray scattering (GIWAXS and GISAXS) measurements have been used to study the crystallization kinetics of the organolead halide perovskite CH₃NH₃PbI_3–xCl_x during thermal annealing. In situ GIWAXS measurements recorded during annealing are used to characterize and quantify the transition from a crystalline precursor to the perovskite structure. In situ GISAXS measurements indicate an evolution of crystallite sizes during annealing, with the number of crystallites having sizes between 30 and 400 nm increasing through the annealing process. Using ex situ scanning electron microscopy, this evolution in length scales is confirmed and a concurrent increase in film surface coverage is observed, a parameter crucial for efficient solar cell performance. A series of photovoltaic devices are then fabricated in which perovskite films have been annealed for different times, and variations in device performance are explained on the basis of X‐ray scattering measurements.     

Solvent‐Induced Morphology in Polymer‐Based Systems for Organic Photovoltaics

Studies on the influence of four different solvents on the morphology and photovoltaic performance of bulk‐heterojunction films made of poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C₆₁ butyric acid methyl ester (PCBM) via spin‐coating for photovoltaic applications are reported. Solvent‐dependent PCBM cluster formation and P3HT crystallization during thermal annealing are investigated with optical microscopy and grazing‐incidence wide‐angle X‐ray scattering (GIWAXS) and are found to be insufficient to explain the differences in device performance. A combination of atomic force microscopy (AFM), X‐ray reflectivity (XRR), and grazing‐incidence small‐angle X‐ray scattering (GISAXS) investigations results in detailed knowledge of the inner film morphology of P3HT:PCBM films. Vertical and lateral phase separation occurs during spin‐coating and annealing, depending on the solvent used. The findings are summarized in schematics and compared with the IV characteristics. The main influence on the photovoltaic performance arises from the vertical material composition and the existence of lateral phase separation fitting to the exciton diffusion length. Absorption and photoluminescence measurements complement the structural analysis.     

Competitive Absorption and Inefficient Exciton Harvesting: Lessons Learned from Bulk Heterojunction Organic Photovoltaics Utilizing the Polymer Acceptor P(NDI2OD‐T2)

Organic solar cells utilizing the small molecule donor 7,7′‐(4,4‐bis(2‐ethylhexyl)‐4H‐silolo[3,2‐b:4,5‐b′]dithiophene‐2,6‐diyl)bis(6‐fluoro‐4‐(5′‐hexyl‐[2,2′‐bithiophen]‐5‐yl)benzo[c][1,2,5] thiadiazole) (p‐DTS(FBTTh₂)₂ and the polymer acceptor poly{[N,N′‐bis(2‐octyldodecyl)‐1,4,5,8‐naphthalenedicarboximide‐2,6‐diyl]‐alt‐5,5′‐(2,2′‐bithiophene)}(P(NDI2OD‐T2)) are investigated and a power conversion efficiency of 2.1% is achieved. By systematic study of bulk heterojunction (BHJ) organic photovoltaic (OPV) quantum efficiency, film morphology, charge transport and extraction and exciton diffusion, the loss processes in this blend is revealed compared to the blend of [6,6]‐phenyl‐C71‐butyric acid methyl ester (PC₇₁BM) and the same donor. An exciton diffussion study using Förster resonant energy transfer (FRET) shows the upper limit of the P(NDI2OD‐T2) exciton diffusion length to be only 1.1 nm. The extremely low exciton diffusion length of P(NDI2OD‐T2), in combination with the overlap in donor and acceptor absorption, is then found to significantly limit device performance. These results suggest that BHJ OPV devices utilizing P(NDI2OD‐T2) as an acceptor material will likely be limited by its low exciton diffusion length compared to devices utilizing functionalized fullerene acceptors, especially when P(NDI2OD‐T2) significantly competes with the donor molecule for photon absorption.     

Measuring Domain Sizes and Compositional Heterogeneities in P3HT‐PCBM Bulk Heterojunction Thin Films with 1H Spin Diffusion NMR Spectroscopy

The application of ¹H spin diffusion nuclear magnetic resonance (NMR) is expanded to polymer‐fullerene blends for bulk heterojunction (BHJ) organic photovoltaics (OPV) by developing a new experimental methodology for measuring the thin films used in poly‐3‐hexylthiophene–phenyl C61‐butyric acid methyl ester (P3HT‐PCBM) OPV devices and by creating an analysis framework for estimating domain size distributions. It is shown that variations in common P3HT‐PCBM BHJ processing parameters such as spin‐coating speed and thermal annealing can significantly affect domain size distributions, which in turn affect power conversion efficiency. ¹H spin diffusion NMR analysis reveals that films spin‐cast at fast speeds in dichlorobenzene are primarily composed of small (<10 nm) domains of each component; these devices exhibit low power conversion efficiencies (η = 0.4%). Fast‐cast films improve substantially by thermal annealing, which causes nanometer‐scale coarsening leading to higher efficiency (η = 2.2%). Films spin‐cast at slow speeds and then slowly dried exhibit larger domains and even higher efficiencies (η = 2.6%), but do not benefit from thermal annealing. The ¹H spin diffusion NMR results show that a significant population of domains tens of nanometers in size is a common characteristic of samples with higher efficiencies.     

Correlating Emissive Non‐Geminate Charge Recombination with Photocurrent Generation Efficiency in Polymer/Perylene Diimide Organic Photovoltaic Blend Films

Evidence for a correlation between the dynamics of emissive non‐geminate charge recombination within organic photovoltaic (OPV) blend films and the photocurrent generation efficiency of the corresponding blend‐based solar cells is presented. Two model OPV systems that consist of binary blends of electron acceptor N′‐bis(1‐ethylpropyl)‐3,4,9,10‐perylene tetracarboxy diimide (PDI) with either poly(9,9‐dioctylfluorene‐co‐benzothiadiazole) (F8BT) or poly(9,9‐dioctylindenofluorene‐co‐benzothiadiazole) (PIF8BT) as electron donor are studied. For the F8BT:PDI and PIF8BT:PDI devices photocurrent generation efficiency is shown to be related to the PDI crystallinity. In contrast to the F8BT:PDI system, thermal annealing of the PIF8BT:PDI layer at 90 °C has a positive impact on the photocurrent generation efficiency and yields a corresponding increase in PL quenching. The devices of both blends have a strongly reduced photocurrent on higher temperature annealing at 120 °C. Delayed luminescence spectroscopy suggests that the improved efficiency of photocurrent generation for the 90 °C annealed PIF8BT:PDI layer is a result of optimized transport of the photogenerated charge‐carriers as well as of enhanced PL quenching due to the maintenance of optimized polymer/PDI interfaces. The studies propose that charge transport in the blend films can be indirectly monitored from the recombination dynamics of free carriers that cause the delayed luminescence. For the F8BT:PDI and PIF8BT:PDI blend films these dynamics are best described by a power‐law decay function and are found to be temperature dependent.     

Rational Design of Small Molecular Donor for Solution‐Processed Organic Photovoltaics with 8.1% Efficiency and High Fill Factor via Multiple Fluorine Substituents and Thiophene Bridge

A series of tetrafluorine‐substituted small molecules with a D₁‐A‐D₂‐A‐D₁ linear framework based on indacenodithiophene and difluorobenzothiadiazole is designed and synthesized for application as donor materials in solution‐processed small‐molecule organic solar cells. The impacts of thiophene π‐bridge and multiple fluorinated modules on the photophysical properties, the energy levels of the highest occupied molecular orbitals (HOMO) and lowest unoccupied molecular orbitals (LUMO), charge carrier mobility, the morphologies of blend films, and their photovoltaic properties as electron donor material in the photoactive layer are investigated. By incorporating multiple fluorine substituents of benzothiadiazole and inserting two thiophene spacers, the fill factor (FF), open‐circuit voltage, and short‐circuit current density are dramatically improved in comparison with fluorinated‐free materials. With the solvent vapor annealing treatment, further enhancement in charge carrier mobility and power conversion efficiency (PCE) are achieved. Finally, a high PCE of 8.1% with very‐high FF of 0.76 for BIT‐4F‐ T/PC₇₁BM is achieved without additional additive, which is among one of the highest reported for small‐molecules‐based solar cells with PCE over 8%. The results reported here clearly indicate that high PCE in solar cells based small molecules can be significantly increased through careful engineering of the molecular structure and optimization on the morphology of blend films by solvent vapor annealing.     

Tuning the Morphology and Performance of Low Bandgap Polymer:Fullerene Heterojunctions via Solvent Annealing in Selective Solvents

Low bandgap polymer (LBG):fullerene mixtures are some of the most promising organic photovoltaic active layers. Unfortunately, there are no post‐deposition treatments available to rationally improve the morphology and performance of as‐cast LBG:fullerene OPV active layers, where thermal annealing usually fails. Therefore, there is a glaring need to develop post‐deposition methods to guide the morphology of LBG:fullerene bulk heterojunctions towards targeted structures and performance. In this paper, the structural evolution of PCPDTBT:PCBM mixtures with solvent annealing (SA) is examined, focusing on the effect of solvent quality of the fullerene and polymer in the annealing vapor on morphological evolution and device performance. The results indicate that exposure of this active layer to the solvent vapor controls the ordering of PCPDTBT and PCBM phase separation very effectively, presumably by inducing component mobility as the solvent plasticizes the mixture. These results also unexpectedly indicate that solvent annealing in a selective solvent provides a method to invert the morphology of the LBG:fullerene mixture from a polymer aggregate dispersed in a polymer:fullerene matrix to fullerene aggregates dispersed in a polymer:fullerene matrix. The judicious choice of solvent vapor, therefore, provides a unique method to exquisitely control and optimize the morphology of LBG conjugated polymer/fullerene mixtures.     

Utilizing intermixing of conjugated polymer and fullerene from sequential solution processing for efficient polymer solar cells

Efficient polymer solar cells based on poly[2, 6-(4, 4-bis-(2-ethylhexyl)-4H-cyclopenta[2,1-b;3,4-b′]dithiophene)-alt-4,7-(2,1,3-fluorobenzothiadiazole)] (PCPDTFBT) and [6,6]-phenyl-C₇₁-butyric acid methyl ester (PC₇₁BM) are successfully fabricated by a sequential processing (SqP). With appropriate orthogonal solvent and thermal treatment, the SqP film can form an inter-diffused layer, and the SqP devices show efficient photovoltaic performance in both conventional and inverted layouts. The SqP inverted device was firstly demonstrated and the highest power conversion efficiency (PCE) of 5.84% with the enhanced J_sc of 16.4 mA cm⁻² was able to be achieved with the high internal quantum efficiency (IQE). Photoluminescence quenching shows the SqP films can provide efficient exciton quenching. X-ray photoemission spectroscopy (XPS) and ellipsometry analysis shows a polymer-rich surface in SqP films after thermal annealing. The charge mobilities in the SqP films were significantly enhanced as measured by space-charge-limited-current (SCLC) method. All these contribute to the improved photovoltaic performance in the inverted SqP device. We believe that these results inspire a new way of forming the active layer with controllable morphology, efficient charge separation and collection in polymer solar cells.     

Efficient Conjugated‐Polymer Optoelectronic Devices Fabricated by Thin‐Film Transfer‐Printing Technique

The fabrication of functional multilayered conjugated‐polymer structures with well‐defined organic‐organic interfaces for optoelectronic‐device applications is constrained by the common solubility of many polymers in most organic solvents. Here, we report a simple, low‐cost, large‐area transfer‐printing technique for the deposition and patterning of conjugated‐polymer thin films. This method utilises a planar poly(dimethylsiloxane) (PDMS) stamp, along with a water‐soluble sacrificial layer, to pick up an organic thin film (～20 nm to 1 µm) from a substrate and subsequently deliver this film to a target substrate. We demonstrate the versatility of this transfer‐printing technique and its applicability to optoelectronic devices by fabricating bilayer structures of poly(9,9‐di‐n‐octylfluorene‐alt‐(1,4‐phenylene‐((4‐sec‐butylphenyl)imino)‐1,4‐phenylene))/poly(9,9‐di‐n‐octylfluorene‐alt‐benzothiadiazole) (TFB/F8BT) and poly(3‐hexylthiophene)/methanofullerene([6,6]‐phenyl C₆₁ butyric acid methyl ester) (P3HT/PCBM), and incorporating them into light‐emitting diodes (LEDs) and photovoltaic (PV) cells, respectively. For both types of device, bilayer devices fabricated with this transfer‐printing technique show equal, if not superior, performance to either blend devices or bilayer devices fabricated by other techniques. This indicates well‐controlled organic‐organic interfaces achieved by the transfer‐printing technique. Furthermore, this transfer‐printing technique allows us to study the nature of the excited states and the transport of charge carriers across well‐defined organic interfaces, which are of great importance to organic electronics.     

Tuning Conversion Efficiency in Metallo Endohedral Fullerene‐Based Organic Photovoltaic Devices

Here the influence that 1‐(3‐hexoxycarbonyl)propyl‐1‐phenyl‐[6,6]‐Lu₃N@C₈₁, Lu₃N@C₈₀–PCBH, a novel acceptor material, has on active layer morphology and the performance of organic photovoltaic (OPV) devices using this material is reported. Polymer/fullerene blend films with poly(3‐hexylthiophene), P3HT, donor material and Lu₃N@C₈₀–PCBH acceptor material are studied using absorption spectroscopy, grazing incident X‐ray diffraction and photocurrent spectra of photovoltaic devices. Due to a smaller molecular orbital offset the OPV devices built with Lu₃N@C₈₀–PCBH display increased open circuit voltage over empty cage fullerene acceptors. The photovoltaic performance of these metallo endohedral fullerene blend films is found to be highly impacted by the fullerene loading. The results indicate that the optimized blend ratio in a P3HT matrix differs from a molecular equivalent of an optimized P3HT/[6,6]‐phenyl‐C₆₁‐butyric methyl ester, C₆₀–PCBM, active layer, and this is related to the physical differences of the C₈₀ fullerene. The influence that active layer annealing has on the OPV performance is further evaluated. Through properly matching the film processing and the donor/acceptor ratio, devices with power conversion efficiency greater than 4% are demonstrated.     

Quantifying Interfacial Electric Fields and Local Crystallinity in Polymer–Fullerene Bulk‐Heterojunction Solar Cells

The challenges of experimentally probing the physical and electronic structures of the highly intermixed organic semiconductor blends that comprise active layers in high‐performance organic photovoltaic (OPV) cells ultimately limit the fundamental understanding of the device performance. We use Fourier‐transform IR (FTIR)‐absorption spectroscopy to quantitatively determine the interfacial electric field in blended poly(3‐hexylthiophene) (P3HT):phenyl‐ C61‐butyric acid methyl ester (PCBM) thin films. The interfacial electric field is ≈0.2 V nm^?1 in the as‐spun film and blends annealing at temperatures as high as 150 °C, which is the optimal annealing temperature in terms of OPV performance. The field decreases to a negligible value upon further annealing to 170 °C, at which temperature PCBM changes from amorphous to crystalline and the open‐circuit voltage of the solar cell decreases from 0.62 to 0.4 V. In addition, our measurements also allow determination of the absolute degree of crystallinity within the acceptor material. The roles of interfacial field and local crystallinity in OPV device performance are discussed.     

Effects of Annealing on the Nanomorphology and Performance of Poly(alkylthiophene):Fullerene Bulk‐Heterojunction Solar Cells

The evolution of nanomorphology within thin solid‐state films of poly(3‐alkylthiophene):[6,6]‐phenyl‐C₆₁ butyric acid methyl ester (P3AT:PCBM) blends during the film formation and subsequent thermal annealing is reported. In detail, the influence of the P3AT's alkyl side chain length on the polymer/fullerene phase separation is discussed. Butyl, hexyl, octyl, decyl, and dodecyl side groups are investigated. All of the P3ATs used were regioregular. To elucidate the nanomorphology, atomic force microscopy (AFM), X‐ray diffraction, and optical spectroscopy are applied. Furthermore, photovoltaic devices of each of the different P3ATs have been constructed, characterized, and correlated with the nanostructure of the blends. It is proposed that the thermal‐annealing step, commonly applied to these P3AT:PCBM blend films, controls two main issues at the same time: a) the crystallization of P3AT and b) the phase separation and diffusion of PCBM. The results show that PCBM diffusion is the main limiting process for reaching high device performances.     

A Thiophene‐Based Anchoring Ligand and Its Heteroleptic Ru(II)‐Complex for Efficient Thin‐Film Dye‐Sensitized Solar Cells

A novel heteroleptic Ru^II complex (BTC‐2) employing 5,5′‐(2,2′‐bipyridine‐4,4′‐diyl)‐bis(thiophene‐2‐carboxylic acid) (BTC) as the anchoring group and 4,4′‐ dinonyl‐2,2′‐bipiridyl and two thiocyanates as ligands is prepared. The photovoltaic performance and device stability achieved with this sensitizer are compared to those of the Z‐907 dye, which lacks the thiophene moieties. For thin mesoporous TiO₂ films, the devices with BTC‐2 achieve higher power conversion efficiencies than those of Z‐907 but with a double‐layer thicker film the device performance is similar. Using a volatile electrolyte and a double layer 7 + 5 μm mesoporous TiO₂ film, BTC‐2 achieves a solar‐to‐electricity conversion efficiency of 9.1% under standard global AM 1.5 sunlight. Using this sensitizer in combination with a low volatile electrolyte, a photovoltaic efficiency of 8.3% is obtained under standard global AM 1.5 sunlight. These devices show excellent stability when subjected to light soaking at 60 °C for 1000 h. Electrochemical impedance spectroscopy and transient photovoltage decay measurements are performed to help understand the changes in the photovoltaic parameters during the aging process. In solid state dye‐sensitized solar cells (DSSCs) using an organic hole‐transporting material (spiro‐MeOTAD, 2,2′,7,7′‐tetrakis‐(N,N‐di‐p‐methoxyphenylamine)‐9,9′‐spirobifluorene), the BTC‐2 sensitizer exhibits an overall power conversion efficiency of 3.6% under AM 1.5 solar (100 mW cm^?2) irradiation.