Impact of ethylene carbonate on ion transport characteristics of PVdF-AgCF3SO3 polymer electrolyte system

The ionic transport in thin film plasticized polymer electrolytes based on polyvinylidene fluoride (PVdF) as the polymer host, silver triflate (AgCF₃SO₃) as salt and ethylene carbonate (EC) as plasticizer prepared by solution casting technique has been reported. Addition of silver triflate has resulted in an increase in the room temperature (298 K) electrical conductivity of the polymer from 10⁻⁶ to 10⁻⁵ S cm⁻¹ whereas incorporation of EC as the plasticizer has further enhanced the conductivity value by an order of magnitude to 10⁻⁴ S cm⁻¹ owing to the possible decrease in crystallinity of the polymer matrix as revealed by the detailed temperature-dependent complex impedance, silver ionic transference number, Fourier transform infrared and X-ray diffraction measurements.     

Chemical diffusion coefficient of lithium ion in Li3V2(PO4)3 cathode material

The kinetic properties of monoclinic lithium vanadium phosphate were investigated by potential step chronoamperometry (PSCA) and electrochemical impedance spectroscopy (EIS) method. The PSCA results show that there exists a linear relationship between the current and the square root of the time. The D?_Li values of lithium ion in Li_3-xV₂(PO₄)₃ under various initial potentials of 3.41, 3.67, 3.91 and 4.07 V (vs Li/Li⁺) obtained from PSCA are 1.26 × 10^− 9, 2.38 × 10^− 9, 2.27 × 10^− 9 and 2.22 × 10^− 9 cm²·s^− 1, respectively. Over the measuring temperature range 15-65 °C, the diffusion coefficient increased from 2.67 × 10^− 8 cm²·s^− 1 (at 15 °C) to 1.80 × 10^− 7 cm²·s^− 1 (at 65 °C) as the measuring temperature increased.     

Ionic conductivity of a gel polymer electrolyte based on Mg(ClO4)2 and polyacrylonitrile (PAN)

Magnesium ion containing gel polymer electrolytes based on polyacrylonitrile (PAN) have been synthesized and characterized using ac impedance measurements. The electrolyte composition having the highest room temperature conductivity was found by varying the ratios propylene carbonate/ethylene carbonate (PC/EC) and PAN/Mg(ClO₄)₂. The corresponding composition was 18 mol% PAN:64 mol% EC:14 mol% PC:4 mol% Mg(ClO₄)₂. The ac conductivity measurements were carried out from room temperature upto 70 °C with blocking (stainless steel) electrodes. The room temperature conductivity is 3.2×10⁻³ S cm⁻¹ and the activation energy is 0.24 eV over the temperature range used. The high conductivity and the low activation energy of the material could possibly be due to the liquid electrolyte, Mg(ClO₄)₂ in EC/PC trapped in a matrix of PAN, as suggested by previous workers. According to dc polarization measurements, the gel electrolyte appears to be predominantly an anionic conductor.     

Electrochemical insertion of Sr ions onto nano δ-MnO2 particles

Manganese dioxide is known to be an important electroactive material for supercapacitors. Generally, δ-MnO₂ is subjected to electrochemical characterization studies in aqueous electrolytes of Na₂SO₄. It exhibits capacitance behaviour in the potential range between 0 and 1.0 V vs. SCE (saturated calomel electrode). In the present study, it is shown that δ-MnO₂ exhibits capacitance behaviour in Sr(NO₃)₂ electrolytes also. The suitable potential range in this electrolyte is also found to be 0-1.0 V. Specific capacitance measured in Sr(NO₃)₂ electrolyte is 192 F g^− 1. X-ray photoelectron spectroscopy data confirm that Sr²⁺ ions get inserted onto δ-MnO₂ nanoparticles.     

Synthesis,characterization and photoluminescence properties of (Gd1−x,Eux)2O2SO4 sub-microphosphors by homogeneous precipitation method

(Gd_1−x,Eu_x)₂O₂SO₄ sub-microphosphors were synthesized by homogeneous precipitation method from commercially available Gd₂O₃, Eu₂O₃, H₂SO₄ and (NH₂)₂CO (urea) starting materials. Fourier transform infrared spectra show that the precursors with different molar ratios of (NH₂)₂CO to Gd₂(SO₄)₃ (the m value) are mostly composed of gadolinium hydroxyl, carbonate and sulfate groups with some crystal water. X-ray diffraction indicated that the precursor (m = 5) can be transformed into pure Gd₂O₂SO₄ phase after heat treated at 900 °C for 2 h in air. Field emission scanning electron microscope micrographs illustrate that the Gd₂O₂SO₄ phosphor particles (m = 5) are quasi-spherical in shape and well dispersed, with a mean particle size of about 300–500 nm. Photoluminescence spectroscopy reveals that the strongest emission peak for (Gd_1−x,Eu_x)₂O₂SO₄ sub-microphosphors is located at 618 nm under 270 nm light excitation, which corresponds to the ⁵D₀ → ⁷F₂ transition of Eu³⁺ ions. The quenching concentration of Eu³⁺ ions is 5 mol% and the concentration quenching mechanism is due to the electric dipole–dipole interaction. Decay study reveals that the ⁵D₀ → ⁷F₂ transition of Eu³⁺ ions fits with a mono exponential function.     

Synthesis and optical properties of (Gd1−x,Eux)2O2SO4 nano-phosphors by a novel co-precipitation method

(Gd_1−x,Eu_x)₂O₂SO₄ nano-phosphors were synthesized by a novel co-precipitation method from commercially available Gd₂O₃, Eu₂O₃, H₂SO₄ and NaOH starting materials. Composition of the precursor is greatly influenced by the molar ratio of NaOH to (Gd_1−x,Eu_x)₂(SO₄)₃ (the m value), and the optimal m value was found to be 4. Fourier transform infrared spectrum (FT-IR) and thermal analysis show that the precursor (m = 4) can be transformed into pure (Gd_1−x,Eu_x)₂O₂SO₄ nano-phosphor by calcining at 900 °C for 2 h in air. Transmission electron microscope (TEM) observation shows that the Gd₂O₂SO₄ phosphor particles (m = 4) are quasi-spherical in shape and well dispersed, with a mean particle size of about 30-50 nm. Photoluminescence (PL) spectroscopy reveals that the strongest emission peak is located at 617 nm under 271 nm light excitation, which corresponds to the ⁵D₀ → ⁷F₂ transition of Eu³⁺ ions. The quenching concentration of Eu³⁺ ions is 10 mol% and the concentration quenching mechanism is exchange interaction among the Eu³⁺ ions. Decay study reveals that the ⁵D₀ → ⁷F₂ transition of Eu³⁺ ions has a single exponential decay behavior.     

Physical properties of flash evaporated In2O3 films prepared at different substrate temperatures

Indium oxide (In₂O₃) thin films were prepared by flash evaporated technique under various substrate temperatures in the range of 303-673 K and systematically studied the structural, electrical and optical properties of the deposited films. The films formed at substrate temperatures of < 373 K were amorphous while those deposited at higher substrate temperatures (≥ 373 K) were polycrystalline in nature. The optical band gap of the films decreased from 3.71 eV to 2.86 eV with the increase of substrate temperature from 303 K to 673 K. Figure of merit of the films increased from 2.8 × 10³ Ω^− 1 cm^− 1 to 4.2 × 10³ Ω^− 1 cm^− 1 with increasing substrate temperature from 303 K to 573 K, thereafter decreased to 2.2 × 10³ Ω^− 1 cm^− 1 at higher temperature of 673 K.     

All-solid-state cells based on solid electrolyte systems Cu1−xAgxI-Ag2O-Y, where x = 0.05-0.25; Y = MoO3, B2O3, SeO2, V2O5 and CrO3

All-solid-state cells of the configuration (−)Ag + SE//SE//I₂-phenothiazine + C(+) using the best conducting compositions of the solid electrolyte systems, namely, Cu_1−xAg_xI-Ag₂O-Y where x = 0.05, 0.1, 0.15, 0.2 and 0.25, Y = MoO₃, B₂O₃, SeO₂, V₂O₅ and CrO₃, as the electrolytes were fabricated. Discharge, polarization and power characteristics of these cells were also evaluated. The open circuit voltage values of these cells were in the range 620-635 mV. The stability of these cells has been indicated by the constancy of their OCV over a period of 6 months. The polarization and discharge studies on these cells have shown that typical cells based on the electrolytes with Y = B₂O₃, SeO₂ and V₂O₅ would possess discharge capacities of 12.84, 3.76 and 5.05 mA h and specific energy of 6.55, 1.81 and 2.77 W h kg⁻¹, respectively. The solid electrolytes have good electrochemical stability and compatibility with the Ag/Phenothiazine-I₂ electrode couple thus offering their suitability of application in microwatt power sources.     

Study on properties of CaO-SiO2-B2O3 system glass-ceramic

Low temperature co-fired ceramic (LTCC) is prepared by sintering a glass selected from CaO-SiO₂-B₂O₃ system, and its sintered bodies are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). It is found that the optimal sintering temperature for this glass-ceramic is 820 °C for 15 min, and the major phases of this material are CaSiO₃, CaB₂O₄ and SiO₂. The glass-ceramic possesses excellent dielectric properties: ?_r = 6.5, tan δ < 2 × 10⁻³ at 10 MHz, temperature coefficient of dielectric constant about −51 × 10⁻⁶ °C⁻¹ and coefficient of thermal expansion about 8 × 10⁻⁶ °C⁻¹ at 20-400 °C. Thus, this material is supposed to be suitable for the tape casting process and be compatible with Ag electrode, which could be used as the LTCC materials for the application in wireless communications.     

Optimization of thermoelectric properties on Bi2Te3 thin films deposited by thermal co-evaporation

The optimization of the thermal co-evaporation deposition process for n-type bismuth telluride (Bi₂Te₃) thin films deposited onto polyimide substrates and intended for thermoelectric applications is reported. The influence of deposition parameters (evaporation rate and substrate temperature) on film composition and thermoelectric properties was studied for optimal thermoelectric performance. Energy-dispersive X-ray spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy and Raman spectroscopy confirmed the formation of Bi₂Te₃ thin films. Seebeck coefficient (up to 250 μV K^− 1), in-plane electrical resistivity (≈10 μΩ m), carrier concentration (3×10¹⁹-20×10¹⁹ cm^− 3) and Hall mobility (80-170 cm² V⁻¹ s^− 1) were measured at room temperature for selected Bi₂Te₃ samples.     

Transport characteristics of ZrO2 dispersed mixed (BaCl2)1−x-(KCl)x solid electrolytes

Composite solid electrolytes in the system [(BaCl₂)_1−x:(KCl)_x]_1−y:(ZrO₂)_y were prepared following the conventional ceramic powder processing route. In the mixed matrix system prepared by melt quench technique, a nominal increase in conductivity (σ) was found in (BaCl₂)_0.9:(KCl)_0.1. On ZrO₂ particle dispersion in this mixed matrix, the maximum conductivity (∼90 times that of base matrix value) was found to occur with 50 m/o of ZrO₂. Conductivity increases monotonically over the temperature range from 100 to 300 °C studied and attains the value of 10 × 10⁻⁶ S cm⁻¹ at 300 °C. The mobility (μ) of the charge carriers at room temperature was found to be 18.5 × 10⁻² cm² V⁻¹ s⁻¹ and the increase in μ with temperature was not very significant. The transference ionic number determination showed that the electrical conductivity of the electrolyte is predominantly due to ions. This study indicates that the conductivity is governed by mobile ion concentration.     

Thermal co-evaporation of Sb2Te3 thin-films optimized for thermoelectric applications

Antimony telluride (Sb₂Te₃) is a chalcogenide material used in thermoelectric applications. The deposition of thin films of Sb₂Te₃ requires a precisely controlled process to achieve a desirable high thermoelectric figure-of-merit. The optimization of the thermal co-evaporation process for p-type Sb₂Te₃ thin-film onto plastic substrates (Kapton© polyimide) for thermoelectric applications is reported. The influence of deposition parameters and composition on thermoelectric properties was studied, seeking optimal thermoelectric performance. Energy-dispersive X-ray spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy and Raman spectroscopy all confirmed the formation of Sb₂Te₃ thin films. Seebeck coefficient (up to 190 μVK⁻¹), in-plane electrical resistivity (8-15 μΩm), carrier concentration (1 × 10¹⁹-7 × 10¹⁹ cm⁻³) and Hall mobility (120-180 cm²V⁻¹s⁻¹) were measured at room temperature for the best Sb₂Te₃ thin-films.     

High-rate synthesis of microcrystalline silicon films using high-density SiH4/H2 microwave plasma

A high electron density (> 10¹¹ cm^− 3) and low electron temperature (1-2 eV) plasma is produced by using a microwave plasma source utilizing a spoke antenna, and is applied for the high-rate synthesis of high quality microcrystalline silicon (μc-Si) films. A very fast deposition rate of ∼ 65 Å/s is achieved at a substrate temperature of 150 °C with a high Raman crystallinity and a low defect density of (1-2) × 10¹⁶ cm^− 3. Optical emission spectroscopy measurements reveal that emission intensity of SiH and intensity ratio of H_α/SiH are good monitors for film deposition rate and film crystallinity, respectively. A high flux of film deposition precursor and atomic hydrogen under a moderate substrate temperature condition is effective for the fast deposition of highly crystallized μc-Si films without creating additional defects as well as for the improvement of film homogeneity.     

Growth and characterization of Ba(Cd1/3Ta2/3)O3 thin films

We have synthesized stoichiometric Ba(Cd_1/3Ta_2/3)O₃ [BCT] (100) dielectric thin films on MgO (100) substrates using Pulsed Laser Deposition. Over 99% of the BCT film was found to be epitaxial [BCT (100) || MgO (100) and BCT (010) || MgO (010)] when grown with an elevated substrate temperature of 635 °C, an enhanced oxygen pressure of 53 Pa and a Cd-enriched BCT target with a 1 mol BCT: 1.5 mol CdO composition. A dielectric constant of 32 was inferred from low-frequency capacitance measurements of a planar interdigital metal pattern. Analysis of ultra violet optical absorption results indicates that BCT has a bandgap of 4.9 eV; while the interference pattern in the visible range is consistent with a refractive index of 2.1. Temperature-dependent electrical measurements indicate that the BCT films have a room temperature conductivity of 3 × 10^− 12 Ω^− 1 cm^− 1 with a thermal activation energy of 0.7 eV. A mean particle size of ~ 100 nm and a root mean square surface roughness of 5 to 6 nm were measured using Atomic Force Microscopy.     

Surface characteristics of parylene-C films in an inductively coupled O2/CF4 gas plasma

In this article, we report the results obtained from a study carried out on the inductively coupled plasma (ICP) etching of poly-monochloro-para-xylylene (parylene-C) thin films using an O₂/CF₄ gas mixture. The effects of adding CF₄ to the O₂ plasma on the etch rates were investigated. As the CF₄ gas fraction increases up to approximately 16%, the polymer etch rate increases in the range of 277-373 nm/min. In this work, the atomic force microscopy (AFM) analysis indicated that the surface roughness was reduced by the addition of CF₄ to the O₂ plasma. Contact angle measurements showed that the surface energy decreases with increasing CF₄ fraction. At the same time, X-ray photoelectron spectroscopy (XPS) demonstrated the increase in the relative F atomic content on the surface.     

Enhanced thermoelectric properties of NaCo2O4 by adding ZnO

The primary phase present in the as-sintered Na(Co_1 − xZn_x)₂O₄ (0 ≤ x ≤ 0.1) bodies was the solid solution of the constituent oxides with a bronze-type layered structure. The electrical conductivity of the Na(Co_1 − xZn_x)₂O₄ samples significantly increased with an increase in ZnO content. The sign of the Seebeck coefficient for all samples was positive over the whole temperature range (723-1073 K), i.e., p-type conduction. The power factor of Na(Co_0.95Zn_0.05)₂O₄ showed an outstanding power factor (1.7 × 10^− 3Wm^− 1 K^− 2) at 1073 K. The power factor was above four times superior to that of ZnO-free NaCo₂O₄ (0.4 × 10^− 3Wm^− 1 K^− 2). This originates from an unusually large Seebeck coefficient (415 μVK^− 1) accompanied with high conductivity (127Ω^− 1 cm^− 1) at 1073 K.     

Influence of spray pyrolysis deposition parameters on the optoelectronic properties of WO3 thin films

The electrochromic (EC) properties of tungsten oxide (WO₃), such as coloration efficiency, cyclic durability and reversibility strongly depend on the structural and morphological properties, which are influenced by the deposition method and parameters.This paper presents the steps for optimizing the deposition parameters (substrate temperature, air flow pressure and precursor solution molarity) for improving the optical and electrical properties of WO₃ thin films for EC applications. WO₃ thin films were deposited by spray pyrolysis using tungsten hexachloride (WCl₆) dissolved in ethanol as precursor solution. The EC properties of optimized films were tested in two different electrolytes (H₂SO₄ 1 M and acetic acid/sodium acetate buffer with pH = 4) and changes in structure, composition and morphology of the films after coloration/bleaching cycles were discussed.The deposition temperature, carrier gas pressure and solution molarity were optimized at 250 °C, 120 kPa and 0.14 M respectively. Under these condition a dense, uniform film, with homogenous distribution of particles, good adhesion to the substrate, low roughness (9.02 nm), high transparency (> 70% in the 500-1100 nm range) and conductivity was obtained. Transmission modulation is higher for the sample cycled in H₂SO₄ 1 M (64% at 630 nm) compared to that cycled in the buffer (21% at 630 nm), whereas opposite results were obtained for coloration efficiencies 28 cm² C^− 1 (at 630 nm) and 35 cm² C^− 1 (at 630 nm), respectively. Changes in surface chemistry and morphology of the optimized sample were observed after cycling in H₂SO₄.     

Thermal properties and infrared spectra analysis of monoclinic RbGd(WO4)2 single crystals

Monoclinic rubidium gadolinium bis(tungstate) single crystals, RbGd(WO₄)₂ (RGW), have been grown by the spontaneous nucleation from high-temperature solutions. The thermal properties were firstly studied by measuring DSC, TG and specific heat. The melting point was determined to be 1089 °C. The measured specific heat ranges from 0.141 J g^− 1 K^− 1 to 0.564 J g^− 1 K^− 1 in the temperature range from 60 °C to 700 °C, a value that is slightly smaller than that of KGd(WO₄)₂. An infrared spectrum of the crystal was recorded in the frequency range of 50 to 1000 cm^− 1 and all vibration frequency peaks were assigned.     

Determination of the chemical diffusion coefficient of lithium in Li3V2(PO4)3

The chemical diffusion of lithium ion in Li₃V₂(PO₄)₃ were investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) methods. The CV results show that there exists a linear relationship between the peak current (i_p) and the square root of the scan rate (ν^1/2). The impedance spectrum exhibits a single semicircle and a straight line in a very low frequency region. A linear behavior was observed for every curve of the real resistance as a function of the inverse square root of the angular frequency in a very low frequency region. The obtained chemical diffusion coefficient from EIS measurements varies within 10^− 9 to 10^− 8 cm²·s^− 1, in good agreement with those from CV results.     

Synthesis and spectroscopic investigations of Mn3O4 nanoparticles

Trimanganese tetraoxide (Mn₃O₄) nanoparticles have been synthesized via hydrothermal process. Nevertheless, homogeneous nanoparticles of Mn₃O₄ with platelet lozange shape were obtained. The crystallite size ranged from 40 to 70 nm. The Mn₃O₄ product was investigated by X-ray diffraction, transmission electron microscopy (MET), and impedance spectroscopy. Electrical conductivity measurements showed that the as-synthesized Mn₃O₄ nanomaterial has a conductivity value which goes from 1.8 10⁻⁷ Ω⁻¹ cm⁻¹ at 298 K, to 23 10⁻⁵ Ω⁻¹ cm⁻¹ at 493 K. The temperature dependence of the conductivity between 298 and 493 K obeys to Arrhenius law with an activation energy of 0.48 eV.