Temperature‐insensitive strain behavior in 0.99[(1−x)Bi0.5(Na0.80K0.20)0.5TiO3−xBiFeO3]–0.01Ta lead‐free piezoelectric ceramics

Lead‐free 0.99[(1?x)Bi_0.5(Na_0.80K_0.20)_0.5TiO₃?xBiFeO₃]–0.01Ta (BNKT20–100xBF–1Ta) lead‐free piezoelectric ceramics were fabricated through conventional solid state sintering method. Results showed that change of BF content in the BNKT20–100xBF–1Ta induced a phase transition from ferroelectric to ergodic relaxor phase with a significant disruption of the long‐range ferroelectric order. A large electric‐field‐induced strain of 0.36% (at 80 kV/cm driving field, corresponding to a large signal of ~450 pm/V) which is derived from a reversible field‐induced ergodic relaxor to ferroelectric phase transformation, was obtained in the composition with x=0.01 near the ferroelectric‐ergodic relaxor phase boundary. Moreover, an attractive property for application in nonlinear actuators demanding enhanced thermal stability was obtained in this material, which showed a temperature‐insensitive strain characteristic in the temperature range from room temperature to 100°C.     

Electrical Properties and Relaxor Phase Evolution of Li‐Modified BNT‐BKT‐BT Lead‐Free Ceramics

By conventional ceramics sintering technique, the lead‐free 0.85Bi_0.5Na_0.5(1?x)Li_0.5xTiO₃‐0.11Bi_0.5K_0.5TiO₃‐0.04BaTiO₃ (x =0–0.15) piezoelectric ceramics were obtained and the effects of Li dopant on the piezoelectric, dielectric, and ferroelectric properties were studied. With increasing Li addition, the temperature‐dependent permittivity exhibited the normal ferroelectric‐to‐ergodic relaxor (FE‐to‐ER) transition temperature (T_FE‐ER, abbreviated as T_F‐R) decreasing down to room temperature. The increasing Li content also enhanced the diffuseness of the FE‐to‐ER transition behavior. For composition with x = 0.15, a large unipolar strain of 0.37% ( = S_max/E_max = 570 pm/V) was achieved under 6.5 kV/mm applied electric field at room temperature. Both unipolar and bipolar strain curves related to the temperature closely, and when the temperature reached the T_F‐R, the normalized strain achieved a maximum value (e.g., for x = 0.10, = 755 pm/V) owing to the electric‐field‐induced ER‐to‐FE state transition.     

Giant electromechanical strain response in lead‐free SrTiO3‐doped (Bi0.5Na0.5TiO3–BaTiO3)–LiNbO3 piezoelectric ceramics

Lead‐free 0.985[(0.94?x)Bi_0.5Na_0.5TiO₃–0.06BaTiO₃–xSrTiO₃]–0.015LiNbO₃ [(BNT–BT–xST)–LN, x=0‐0.05] piezoelectric ceramics were prepared using a conventional solid‐state reaction method. It was found that the long‐range ferroelectric order in the unmodified (BNT–BT)–LN ceramic was disrupted and transformed into the ergodic relaxor phase with the ST substitution, which was well demonstrated by the dramatic decrease in remnant polarization (P_r), coercive field (E_c), negative strain (S_neg) and piezoelectric coefficient (d₃₃). However, the degradation of the ferroelectric and piezoelectric properties was accompanied by a significant increase in the usable strain response. The critical composition (BNT–BT–0.03ST)–LN exhibited a maximum unipolar strain of ~0.44% and corresponding normalized strain, S_max/E_max of ~880 pm/V under a moderate field of 50 kV/cm at room temperature. This giant strain was associated with the coexistence of the ferroelectric and ergodic relaxor phases, which should be mainly attributed to the reversible electric‐field‐induced transition between the ergodic relaxor and ferroelectric phases. Furthermore, the large field‐induced strain showed relatively good temperature stability; the S_max/E_max was as high as ~490 pm/V even at 120°C. These findings indicated that the (BNT–BT–xST)–LN system would be a suitable environmental‐friendly candidate for actuator applications.     

Orientation‐Dependence of Thermal Depolarization and Phase Development in Bi1/2Na1/2TiO3‐BaTiO3 Single Crystals

The direction‐dependence of pyroelectric properties of (1 ? x)Bi_1/2Na_1/2TiO₃ ? xBaTiO₃ (BNT ? 100xBT) is investigated, using single crystal samples with well‐defined orientations for x = 0.036 and x = 0.063. The results are compared with those of temperature‐dependent measurements of the ferroelectric and dielectric hysteresis. The depolarization temperature T_d of each crystal composition is found to depend on crystal orientation, a fact that is explained by differences in the stability of respective domain configurations. A rationalization is offered for the observation that T_d differs from the ferroelectric‐relaxor transition temperature, depending on orientation. The hysteresis curves of BNT ? 3.6BT are typical for a rhombohedral system with a ferroelectric‐relaxor transition, with polarization reversal close to T_d occurring in a multistep process that includes decay of ferroelectric domains into polar nanoregions and re‐formation of domains. BNT ? 6.3BT, a composition in the region of the morphotropic phase boundary, shows the same feature, but additionally is characterized by a field‐induced transition between rhombohedral and tetragonal symmetry. This combination results in an effective piezoelectric coefficient of pm/V.     

Composition‐induced structural transitions and enhanced strain response in nonstoichiometric NBT‐based ceramics

In this work, the nonstoichiometric 0.99Bi_0.505(Na_0.8K_0.2)_0.5‐xTiO₃‐0.01SrTiO₃ (BNKST(0.5‐x)) ceramics with x=0‐0.03 were synthesized by conventional solid‐state reaction method. The composition‐induced structural transitions were investigated by Raman spectra, dielectric analyses, and electrical measurements. It is found that the relaxor phase can be induced through the modulation of the (Na, K) content. The (Na, K) deficiency in BNKST(0.5‐x) ceramics favors a more disordered local structure and can result in the loss of long‐range ferroelectricity. The x=0.015 critical composition possesses relatively high positive strain S_pos of 0.42% and large signal piezoelectric constant d₃₃* of 479 pm V^?1 at 6 kV mm^?1, along with the good temperature (25‐120°C) and frequency (1‐20 Hz) stability. The recoverable large strain responses in nonstoichiometric ceramics can be attributed to the reversible relaxor‐ferroelectric phase transition, which is closely related to the complex defects (, , and ) and the local random fields. This work may be helpful for the exploration of high‐performance NBT‐based lead‐free materials by means of A‐site compositional modification.     

NaNbO3‐BaTiO3‐NaSbO3 lead and potassium‐free ceramics with thermally stable small‐signal piezoelectric properties

A new lead‐potassium‐free ceramic of (0.9‐x)NaNbO₃‐0.1BaTiO₃‐xNaSbO₃ (NN‐BT‐xNS) was successfully prepared via a solid‐state reaction method. The microstructure, phase structure, dielectric, ferroelectric, and piezoelectric properties were investigated as a function of NS content. The substitution of NS for NN was found to dramatically change the grain morphology from cube‐like grains typical for alkaline niobate‐based ceramics to conventional sphere‐like grains especially for Pb‐based perovskite ceramics. A normal to relaxor ferroelectric phase transformation was accompanied by a tetragonal (T) to rhombohedral (R) phase transition. A composition‐temperature phase diagram demonstrated a vertical morphotropic phase boundary between T and R phases in the composition range of x=0.03‐0.04, where optimum electrical properties of d₃₃=252 pC/N, k_p=36%, Q_m=168, =2063, and T_c=109°C were obtained in the x=0.035 ceramic sintered at 1260°C. Particularly, excellent temperature insensitivity of small‐signal piezoelectric properties suggested large application potentials in various actuators and sensors in comparison with other typical lead‐free materials.     

Effect of BiMeO3 on the Phase Structure,Ferroelectric Stability,and Properties of Lead‐Free Bi0.5(Na0.80K0.20)0.5TiO3 Ceramics

The effects of BiMeO₃ (Me = Fe, Sc, Mn, Al) addition on the phase transition and electrical properties of Bi_0.5(Na_0.80K_0.20)_0.5TiO₃ (BNKT20) lead‐free piezoceramics were systematically investigated. Results showed that addition of BiFeO₃ into BNKT20 induces a phase transition from tetragonal–rhombohedral coexisted phases to a tetragonal phase with the observation of enhanced piezoelectric properties (d₃₃ = 150 pC/N for 0.02BiFeO₃). BiScO₃, BiMnO₃, and BiAlO₃ substitutions into BNKT20 induce a phase transition from coexistence of ferroelectric tetragonal and rhombohedral to a relaxor pseudocubic with a significant disruption of the long‐range ferroelectric order, and correspondingly adjusts the ferroelectric–relaxor transition point T_F–R to room temperature. Accordingly, large accompanying normalized strains of 0.34%–0.36% are obtained near the ferroelectric–relaxor phase boundary, and the mergence of large strain response can be ascribed to a reversible field‐induced ergodic relaxor‐to‐ferroelectric phase transformation. Moreover, our study also revealed that the composition located at the ferroelectric–relaxor phase boundary where the strain response is consistently derivable shifts to a BNKT20‐rich composition as the tolerance factor t of the end‐member BiMeO₃ increases, and this relationship is expected to provide a guideline for designing high‐performance (Bi_0.5Na_0.5)TiO₃‐based materials by searching the ferroelectric–relaxor phase boundary.     

Composition‐ and Temperature‐Dependent Large Strain in (1−x)(0.8Bi0.5Na0.5TiO3–0.2Bi0.5K0.5TiO3)– xNaNbO3 Ceramics

Ternary solid solutions of (1 ? x)(0.8Bi_0.5Na_0.5TiO₃–0.2Bi_0.5K_0.5TiO₃)– xNaNbO₃ (BNKT–xNN) lead‐free piezoceramics were fabricated using a conventional solid‐state reaction method. Pure BNKT composition exhibited an electric‐field‐induced irreversible structural transition from pseudocubic to ferroelectric rhombohedral phase at room temperature. Accompanied with the ferroelectric‐to‐relaxor temperature T_F‐R shifted down below room temperature as the substitution of NN, a compositionally induced nonergodic‐to‐ergodic relaxor transition was presented, which featured the pinched‐shape polarization and sprout‐shape strain hysteresis loops. A strain value of ~0.445% (under a driving field of 55 kV/cm) with large normalized strain of ~810 pm/V was obtained for the composition of BNKT–0.04NN, and the large strain was attributed to the reversible electric‐field‐induced transition between ergodic relaxor and ferroelectric phase.     

Large Strain Response and Fatigue‐Resistant Behavior in Ternary Bi0.5Na0.5TiO3–BaTiO3–Bi(Zn0.5Ti0.5)O3 Solid Solutions

A ternary solid solution (1 ? x)(0.88Bi_0.5Na_0.5TiO₃–0.12BaTiO₃)‐xBi(Zn_0.5Ti_0.5)O₃ (BNBZT, BNBZTx) was designed and fabricated using the traditional solid‐state reaction method. The temperature and composition dependence of dielectric, ferroelectric, piezoelectric, and fatigue properties were systematically investigated and a schematic phase diagram was proposed. The substitution with Bi(Zn_0.5Ti_0.5)O₃ was found to shift the phase transition (ferroelectric tetragonal to relaxor pseudocubic phase) to lower temperatures. At a critical composition x of 0.05, large electric‐field‐induced strain response with normalized strain S_max/E_max as high as 526 pm/V was obtained under a moderate field of 4 kV/mm around room temperature. The strain exhibited good temperature stability within the temperature range of 25°C–120°C. In addition, excellent fatigue‐resistant behavior was observed in the proposed BNBZT solid solution after 10⁶ bipolar cycles. These give the BNBZT system great potential as environmental friendly solid‐state actuator.     

Ferroelectric,piezoelectric and electrostrictive properties of Sn4+‐modified Ba0.7Ca0.3TiO3 lead‐free electroceramics

Lead‐free Ba_0.7Ca_0.3Ti_1?xSn_xO₃ (x=0.00, 0.025, 0.050, 0.075, and 0.1, abbreviated as BCST) electroceramic system was prepared by the solid‐state reaction method and its ferroelectric, piezoelectric, and electrostrictive properties were investigated. X‐ray diffraction shows that the compositions with x≤0.05 exhibit a tetragonal crystal structure having P4mm symmetry; while the compositions x=0.075 and 0.1 exhibit a mixed P4mm+Amm2 phase coexistence of tetragonal and orthorhombic and P4mm+Pmm pseudo‐cubic lattice symmetries, respectively, at room temperature. The dense microstructure having relative density ~90%‐92% and average grain size in the range ~2.36 μm to 8.56 μm was observed for BCST ceramics. Temperature‐dependent dielectric measurements support the presence of phase coexistence and show the decrease in Curie temperature (T_C) with Sn⁴⁺ substitution. The dielectric loss (tan δ) values in the temperature range (?100°C to 150°C) was observed to be <4%, for all BCST ceramics. The BCST compositions exhibit typical polarization‐electric field (P‐E) hysteresis and electric field induced strain (S‐E) butterfly loop, which confirms the ferroelectric and piezoelectric character. The compositions x=0.025, 0.05 and 0.075 show the peaking behavior of displacement current density () to an applied electric field () (J‐E) which implies the saturation state of polarization. The maximum electrostrictive coefficient (Q₃₃) value of 0.0667 m⁴/C² was observed for x=0.075 and it is higher than some of the significant lead‐based electrostrictive materials. The compositions x=0.05 and 0.075 exhibit the notable electrostrictive properties that may be useful for piezoelectric Ac device applications. The observed results are discussed and correlated with the structure‐property‐composition.     

Reduced Dielectric Loss and Strain Hysteresis in Fe and Mn Comodified High‐Temperature BiScO3–PbTiO3 Ceramics

There is a growing requirement for high‐temperature piezoelectric materials in the petrochemical, automotive, and aerospace industries. Here, the piezoelectric materials of Fe and Mn comodified 0.36BiScO₃–0.64PbTiO₃ (BS‐PTFMn) ceramics with high Curie temperature (T_c), large mechanical quality factor (Q_m), and reduced strain hysteresis were presented. XRD results revealed that all the BS‐PTFMn ceramics have a pure perovskite structure with tetragonal symmetry, and the ratio of c/a is insensitive to the contents of Fe. With the modifications of Fe, the dielectric loss tanδ and strain hysteresis decrease clearly, while the mechanical quality factor improves significantly. The Curie temperature, piezoelectric constant, planar electromechanical coupling factor, dielectric loss, and mechanical quality factor of the BS‐PTFMn with 3% Fe content are 492°C, 235 pC/N, 0.38, 0.6%, and 280, respectively. BS‐PTFMn ceramics show 50°C higher T_c than BS‐PT morphotropic phase boundary composition. The figure of merit (product of Q_m, and k_ij) of BS‐PTFMn ceramics is about five times than that of pure BS‐PT ceramics. Furthermore, for the BS‐PTFMn ceramics with Fe content of 3 mol%, the high field strain coefficient value calculated from the electric‐field‐induced strain curves (S_max/E_max) is 320 pm/V, while the strain hysteresis (under 40 kV/cm) is reduced to one fifth that of unmodified BS‐PT ceramics. Moreover, the temperature‐dependent electromechanical coupling coefficient and dielectric constant are very stable in the temperature range from room temperature (RT) to 450°C. These results indicated that BS‐PTFMn ceramics are promising for high‐temperature piezoelectric applications.     

Ferroelectric‐quasiferroelectric‐ergodic relaxor transition and multifunctional electrical properties in Bi0.5Na0.5TiO3‐based ceramics

A‐site substituted 0.88(Bi_0.5Na_0.5)_1?x(Li_0.5Nd_0.5)_xTiO₃–0.12BaTiO₃ (BNTLNx–BT12) ceramics were synthesized using a conventional solid‐state reaction route. The structural transformation and miscellaneous electrical properties were systematically investigated. The A‐site modification induced two sequence transitions from ferroelectric tetragonal (T) to quasi‐ferroelectric pseudocubic (PC) phase, followed closely by the second transition from non‐ergodic to ergodic relaxor (NR‐ER), and finally to dynamic polar nanoregions (PNRs). The significant enhancement in piezoelectric activity, strain response, broad plateau‐like maximum dielectric permittivity over a large temperature range and energy‐storage level at different compositions may be attributed to the compositionally‐induced T‐PC to NR‐ER transition and the alignment of dynamically‐fluctuating PNRs, respectively. The evolution of multifunctional electrical properties, associated with the variations in structure/microstructure, might provide a new insight to investigate the underlying mechanism of structure‐electrical properties relationship in ferroelectric solid solutions.     

Sodium Excess Ta‐Modified (K0.5Na0.5)NbO3 Ceramics Prepared by Reactive Template Grain Growth Method

Lead‐free sodium excess Ta‐modified (K_0.470Na_0.545)(Nb_0.55Ta_0.45)O₃ (KNNT) ceramics were synthesized by a conventional and reactive templated grain growth methods, and their degree of grain orientation, microstructure, dielectric, ferroelectric, and field‐induced strain properties were systematically investigated. A high degree of grain orientation (Lotgering factor F = 80%) was obtained in textured KNNT ceramics. Results showed that textured KNNT ceramics exhibit high grain orientation, dielectric constant, and field‐induced strain as compared to nontextured samples of the same composition. Room temperature unipolar field‐induced strain of K_0.5Na_0.5NbO₃ (KNN) ceramics was enhanced from 0.080% for nontextured sample to 0.115% for textured sample, and their corresponding dynamic piezoelectric coefficients () were improved from 320 pm/V to 460 pm/V, respectively.     

Quantitative analyses of electric field–induced phase transition in (Na,K)0.5Bi0.5TiO3:Eu ceramics by photoluminescence

Most reported results about phase transition probed by the photoluminescence (PL) spectra of Eu³⁺ ions are qualitative, but the quantitative analyses of phase transition were presented in this work. We fabricated (Na_0.8, K_0.2)_0.5Bi_0.497Eu_0.003TiO₃ (NKBT20:Eu) ferroelectric ceramics and investigated the phase structures and the PL spectra of NKBT20:Eu ceramics before and after poling at different electric fields. The PL spectra indicate a phase transition from tetragonal phase (T phase) to rhombohedral phase (R phase) within NKBT20:Eu ceramics after poling, consistent with the analyses by X-ray diffraction (XRD). Moreover, the emission intensity ratios of the “hypersensitive” transition to the magnetic dipole transition could be used to calculate the fractions of the phase transition quantitatively, which were further confirmed by XRD Rietveld refinements. This study provides a different perspective to investigate the phase transition induced by electric field for NKBT20:Eu ceramics, qualitatively and quantitatively, and the method is expected to be useful in more cases of phase analyses.     

High‐Performance Small‐Amount Fe2O3‐Doped (K,Na)NbO3‐Based Lead‐Free Piezoceramics with Irregular Phase Evolution

[(K_0.43Na_0.57)_0.94Li_0.06][(Nb_0.94Sb_0.06)_0.95Ta_0.05]O₃ + x mol% Fe₂O₃ (KNLNST + x Fe, x = 0~0.60) lead‐free piezoelectric ceramics were prepared by conventional solid‐state reaction processing. The effects of small‐amount Fe₂O₃ doping on the microstructure and electrical properties of the KNLNST ceramics were systematically investigated. With increasing Fe³⁺ content, the orthorhombic‐tetragonal polymorphic phase transition temperature (T_O‐T) of KNLNST + x Fe ceramics presented an obvious “V” type variation trend, and T_O‐T was successfully shifted to near room temperature without changing T_C (T_C = 315°C) via doping Fe₂O₃ around 0.25 mol%. Electrical properties were significantly enhanced due to the coexistence of both orthorhombic and tetragonal ferroelectric phases at room temperature. The ceramics doped with 0.20 mol% Fe₂O₃ possessed optimal piezoelectric and dielectric properties of d₃₃ = 306 pC/N, k_p = 47.0%, = 1483 and tan δ = 0.023. It was revealed that the strong internal stress in the KNLNST + x Fe ceramics with higher Fe³⁺ contents (x = 0.40, 0.60) stabilized the orthorhombic phase, leading to the irregular “V” type rather than the usually observed monotonic phase transition with composition change in the ceramics.     

Dielectric Relaxor Evolution and Frequency‐Insensitive Giant Strains in (Bi0.5Na0.5)TiO3‐Modified Bi(Mg0.5Ti0.5)O3–PbTiO3 Ferroelectric Ceramics

The 0.45Bi(Mg_0.5Ti_0.5)O₃–(0.55 ? x)PbTiO₃–x(Bi_0.5Na_0.5)TiO₃ (BMT–PT–xBNT) ternary solid solution ceramics were prepared via a conventional solid‐state reaction method; the evolution of dielectric relaxor behavior and the electrostrain features were investigated. The XRD and dielectric measurements showed that all studied compositions own a single pseudocubic perovskite structure and undergo a diffuse‐to‐relaxor phase transition owing to the evolution of the domain from a frozen state to a dynamic state. The formation of the above dielectric relaxor behavior was further confirmed by a couple of measurements such as polarization loops, polarization current density curves, as well as bipolar strain loops. A large strain value of ~0.41% at a driving field of 7 kV/mm (normalized strain d₃₃* of ~590 pm/V) was obtained at room temperature for the composition with x = 0.32, which is located near the boundary between ergodic and nonergodic relaxor. Moreover, this electric field‐induced large strain was found to own a frequency‐insensitive characteristic.     

Re-entrant ferroelectric relaxor phenomena in the (1 − x)[Bi1/2(Na1/2K1/2)1/2TiO3]-xPbZrO3 system

The solid solution (1 − x)[Bi_1/2(Na_1/2K_1/2)_1/2TiO₃]-xPbZrO₃, (0.00 ≤ x ≤ 0.12) was investigated to examine the phase equilibria, dielectric and electromechanical properties. The composition corresponding to x = 0.00 exhibits tetragonal symmetry with the expected classical ferroelectric (FE) behavior. The system exhibited FE to relaxor crossover with the addition of lead zirconate at the composition x = 0.05. This is indicated by typical relaxor characteristics such as a transition to the global pseudocubic phase, a constriction in the FE hysteresis loop, and a sudden decrease in the negative strain accompanied by an increase in maximum strain. Most notably, with a further increase in x (>0.05), there is evidence for a return to a FE phase that exhibits classical FE characteristics. The combined results demonstrate that there exists a narrow FE-relaxor boundary near x = 0.05, where FE and relaxor phases coexist. At the critical composition, enhancement in the piezoelectric properties, including an increase in the effective (350 pm/V) was observed. This transition in the electromechanical properties is consistent with changes observed in the phase equilibria for this solid solution. The crystal structure transitions from tetragonal symmetry for x = 0.00, to pseudocubic symmetry for the relaxor compositions (x = 0.05), and finally to a lower symmetry perovskite phase for the re-entrant FE phase (x> 0.05). This composition-induced transition from FE to relaxor to a re-entrant FE state in the (1 − x)[Bi_1/2(Na_1/2K_1/2)_1/2TiO₃]-xPbZrO₃ system is unusual among relaxor FE systems and thus is of great scientific and technological interest.     

Defect‐driven evolution of piezoelectric and ferroelectric properties in CuSb2O6‐doped K0.5Na0.5NbO3 lead‐free ceramics

Defect greatly affects the microscopic structure and electrical properties of perovskite piezoelectric ceramics, but the microscopic mechanism of defect‐driven macroscopic properties in the materials is not still completely comprehended. In this work, K_0.5Na_0.5NbO₃+x mol CuSb₂O₆ lead‐free piezoelectric ceramics were fabricated by a solid‐state reaction method and the defect‐driven evolution of piezoelectric and ferroelectric properties was studied. The addition of CuSb₂O₆ induces the formation of dimeric (DC1) and trimeric (DC2) defect dipoles. At low doping concentration of CuSb₂O₆ (0.5‐1.0 mol%), DC1 and DC2 coexist in the ceramics and harden the ceramics, inducing a constricted double P‐E loop and high Q_m of 895 at x=0.01. However, DC2 becomes more dominant in the ceramics with high concentration of CuSb₂O₆ (≥1.5 mol%) and thus leads to softening behavior of piezoelectricity and ferroelectricity as compared to the ceramic with x=0.01, giving a single slanted P‐E loop and relatively low Q_m of 206 at x=0.025. All ceramics exhibit relatively high d₃₃ of 106‐126 pC/N. Our study shows that the piezoelectricity and ferroelectricity of K_0.5Na_0.5NbO₃ ceramics can be tailored by controlling defect structure of the materials.     

Electric‐field induced phase transition and fatigue behaviors of (Bi0.5+x/2Na0.5‐x/2)0.94Ba0.06Ti1‐xFexO3 ferroelectrics

The dielectric, piezoelectric properties, and fatigue behaviors of stoichiometric (Bi_0.5+x/2Na_0.5‐x/2)_0.94Ba_0.06Ti_1‐xFe_xO₃ (BNBT‐xFe) ferroelectrics are investigated. Fe substitution leads to the downward shift of the ferroelectric‐relaxor transition temperature (T_F‐R) and increase in strain. Meanwhile, fatigue behaviors of the modified ceramics are significantly enhanced. Ex situ X‐ray diffraction and transmission electron microscopy reveal microscopic mechanism for polarization fatigue on different compositions. The fatigue‐free behavior of ferroelectric BNBT‐0.03Fe is not only attributed to a mechanism involving the formation of defect dipoles, which reduces the pinning effect of migratory oxygen vacancies on domain walls, but is also connected to the decrease in easily suppressed field‐induced ferroelectric tetragonal phase. While for ergodic relaxor BNBT‐0.09Fe, the absence of domain wall contributes to the good fatigue resistance behavior. Interestingly, electric cycling results in an increased fraction of relaxor phase, accompanying by the increase in the total strain and decrease in remnant polarizations.     

Effect of the (Ba + Sr)/Ti ratio on the microwave‐tunable properties of Ba0.6Sr0.4TiO3 ceramics

The impact of the (Ba + Sr)/Ti (A/B) ratio on the microwave‐tunable characteristics of diffuse phase transition (DPT) ferroelectric Ba_0.6Sr_0.4TiO₃ (0.6‐BST) ceramics was investigated. The reduction in the lattice constant with increasing nonstoichiometry was attributed to introduced partial Schottky defects, i.e., and . The magnitude of the dielectric constant, ε′, at room temperature in the absence of an applied electric field was governed by the shift in the dielectric maximum temperature, T_m, because T_m was close to room temperature for the 0.6‐BST. The dielectric loss, tanδ, diminished as the ε′ decreased for 0.98≤A/B≤1.05, while the tanδ was much higher for A/B=0.95 having the greatest A‐site vacancy loading. The negatively charged and were mainly compensated by oxygen vacancies and likely partly compensated by holes, h^?, which contributed to the electrical conduction. The tunability, T, at 100 MHz was almost constant at 20%–25% for A/B≥1.00 despite the reduction of the ε′, whereas T decreased for A/B<1.00 to ca. 10% for A/B=0.95 having the greatest A‐site vacancy loading. The results implied that the for larger A/B values was more efficient in generating nucleation sites in the polar nanoregions (PNRs) than the for smaller A/B values, thereby providing greater dipole polarization. Consequently, the figure of merit, FOM, reached its maximum of 250 at A/B=0.9875, which was ca. 155% higher than that of the stoichiometric BST.