Electrospun Poly(l‐Lactic Acid) Nanofibers for Nanogenerator and Diagnostic Sensor Applications

This paper presents for the first time that poly(l ‐lactic acid) (PLLA) nanofibers can show the piezoelectricity along the fiber direction (d₃₃) by using an electrospinning method. First, the electrospun fiber bundles are characterized by scanning electron microscope, X‐ray, and piezoelectric coefficient measurements. The data show that the supercritical CO₂ treatment can greatly enhance the piezoelectricity of electrospun PLLA fibers, which can be resulting from the increased crystallinity of the fibers. Later, it is found that the electrospun PLLA fiber can generate a current of 8 pA and a voltage of 20 mV by a simple push–release process. Further, a single PLLA fiber‐based blood pulse sensor is also fabricated and tested and shows around a 2 pA output for blood pulse. Due to easy fabrication and relatively simple structure, this device enables a broad range of promising future applications in the medical sensor area.

     

Uranium(VI) Removal from Aqueous Solution by Poly(Amic Acid)-Modified Marine Fungus

Fusarium sp. #ZZF51, marine-derived mangrove endophytic fungus, was chemically modified by poly(amic acid) to enhance its potential of uranium(VI) biosorption in aqueous solution. Compared with uranium(VI) removal of the pristine biomass, the maximum uranium(VI) adsorption capacity of the modified biomass increased 9.5-fold under the optimal condition of pH 5.0, S/L 0.4, and equilibrium time 180 min. Kinetic study showed that the process follows the pseudo-second-order kinetic model, which indicates that chemical reaction controls the adsorption rate. The thermodynamic experimental data fit well with Langumir, Freundlich, and Temkin isotherms, and their R ² values are 0.954, 0.963, and 0.986, respectively. FTIR spectroscopic analysis of the native, modified, and uranium-loaded biomass demonstrated the involvement of carboxyl, amide, and hydroxyl groups on the surface of fungus Fusarium sp. #ZZF51 cell wall in the adsorption of uranium(VI).     

Effect of Processing Variables on the Morphology of Electrospun Poly[(lactic acid)‐co‐(glycolic acid)] Nanofibers

A systematic study of the effects of , flow rate, voltage, and composition on the morphology of electrospun PLGA nanofibers is reported. It is shown that changes of voltage and flow rate do not appreciably affect the morphology. However, the of PLGA predominantly determines the formation of bead structures. Uniform electrospun PLGA nanofibers with controllable diameters can be formed through optimization. Further, multi‐walled carbon nanotubes can be incorporated into the PLGA nanofibers, significantly enhancing their tensile strength and elasticity without compromising the uniform morphology. The variable size, porosity, and composition of the nanofibers are essential for their applications in regenerative medicine.

     

Improving Mechanical Properties of Carbon/Epoxy Composite by Incorporating Functionalized Electrospun Polyacrylonitrile Nanofibers

Electrospun functionalized polyacrylonitrile grafted glycidyl methacrylate (PAN‐g‐GMA) nanofibers are incorporated between the plies of a conventional carbon fiber/epoxy composite to improve the composite's mechanical performance. Glycidyl methacrylate (GMA) is successfully grafted onto polyacrylonitrile (PAN) polymer powder via a free radical mechanism. Characterization of the electrospun PAN and PAN‐g‐GMA nanofibers indicates that the grafting of GMA does not significantly alter the tensile properties of the PAN nanofibers but results in an increase in the diameter of nanofibers. Statistical analysis of the mechanical characterization studies on PAN‐carbon/epoxy hybrid composites conclusively shows that the composite reinforced with functionalized PAN nanofibers has greater mechanical properties than that of both the neat PAN nanofiber enriched hybrid composite and control composite (without nanofibers). The improved performance is attributed to the grafted glycidyl groups on PAN, leading to stronger interactions between the nanofibers and the epoxy matrix. PAN‐g‐GMA nanofiber reinforced composite outperforms their neat PAN counterparts in tensile strength, short beam shear strength, flexural strength, and Izod impact energy absorption by 8%, 9%, 6%, and 8%, respectively. Compared to the control composite, the improvements resulting from the PAN‐g‐GMA nanofiber incorporation are even more pronounced at 28%, 41%, 32%, and 21% in the corresponding tests, respectively.

     

Biodegradable Electrospun Poly(lactic acid) Nanofibers for Effective PM 2.5 Removal

In addition to the rapid urbanization and industrialization around the world, air pollution due to particulate matter is a substantial threat to human health. A considerable research effort has been devoted to the development of electrospun polymer nanofibers for air filter applications. Among these new technologies, electrostatic charge‐assisted air filtration is a promising technology for removing small particulate matter (PM). In this investigation, biodegradable electrospun poly(l ‐lactic acid) (PLLA) polymer nanofibers are employed for air filter applications. Electrostatic charges generated from the PLLA nanofiber can significantly enhance air filter applications. Compared with a 3M commercial respirator filter, electrospun PLLA fibrous filters exhibit a high efficiency of 99.3%. Even after 6 h of filtration time, the PLLA filtration membrane still exhibits a 15% improvement in quality factor for PM 2.5 particles than the 3M respirator. This is mainly attributed to the electrostatic force generated from the electrospun PLLA nanofibers, which significantly benefit submicron particle absorption. Due to their biodegradability, ease of fabrication, and relatively high efficiency, electrospun PLLA nanofibers show great promise in applications such as air cleaning systems and personal air purifier applications.     

Synthesis and Substrate-Aided Alignment of Porphyrinated Poly(ethylene oxide) (PEO) Electrospun Nanofibers

Aligned and unaligned vanadium (IV) oxide meso-tetraphenyl porphine (VMP)/polyethylene oxide (PEO) hybrid nanofibers have been successfully synthesized by electrospinning technique. The nanofibers were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), atomic force microscopy (AFM), optical microscopy and scanning electron microscopy (SEM). The SEM and AFM analyses of the morphology showed that the nanofibers are cylindrical with diameters ranging from 400–700 nm. The AFM analysis also confirmed that the aligned nanofibers deposited on a small metallic spring are smoother than the unaligned ones deposited on FTO. FTIR analysis showed that the polar environment provided by the phenyl groups of VMP molecules modified the chemical configuration of PEO molecules, and XRD studies indicated that the VMP molecules were homogeneously distributed within the PEO matrix.     

哌嗪基单丁酰胺酸钙/锌的合成及对PVC热稳定性研究

以丁二酸酐、哌嗪、氯化钙、氯化锌为原料,通过两步反应制备了哌嗪基单丁酰胺酸钙/锌（PSACa/Zn）热稳定剂。采用元素分析、电感耦合等离子体原子发射光谱仪（ICP?OES）和傅里叶变换红外光谱仪（FTIR）对产品结构进行表征,通过刚果红试纸法、转矩流变仪法、热失重法考察了PSACa/Zn对PVC的热稳定性能,并筛选了PSACa和PSAZn的最佳配比。结果表明,PSACa和PSAZn对PVC的静态热稳定时间分别可达74.5、41.5 min,优于硬脂酸钙（CaSt₂）、硬脂酸锌（ZnSt₂）热稳定剂;PSACa和PSAZn复配使用时,以m_PSACa∶m_PSAZn=1∶1时性能最佳,对PVC静态热稳定时间可达92 min,动态热稳定时间可达905 s;发现PSACa/Zn对PVC的长期热稳定性良好。     

Fabrication and Characterization of Highly Oriented Composite Nanofibers with Excellent Mechanical Strength and Thermal Stability

Here, highly‐oriented poly(m‐phenylene isophthalamide)/polyacrylonitrile multi‐walled carbon nanotube (PMIA/PAN‐MWCNT) composite nanofiber membranes with excellent mechanical strength and thermal stability are successfully produced using electrospinning. It is demonstrated that the cooperation of multi‐walled carbon nanotubes (MWCNT) and high‐speed rotating collection is beneficial to the acquisition of highly oriented fibers and effectively improves the mechanical strength of the membrane along the orientation direction. Specifically, the tensile stress of poly(m‐phenylene isophthalamide)/polyacrylonitrile (PMIA/PAN) membrane is enhanced significantly from 10.6 to 20.7 MPa, benefiting from the highly oriented alignment of the fibers as well as the reinforcing effect of MWCNTs on the fibers. Furthermore, the stressing process of single fiber and fiber aggregates is carefully simulated, and the influence of MWCNTs on the mechanical properties of PMIA/PAN‐MWCNT membranes is analyzed comprehensively, providing a meaningful auxiliary means for the study of mechanical properties. In addition, the composite nanofiber membrane has the advantages of both PMIA and PAN, possessing high temperature resistance, flame‐retardancy, and chemical stability, for an ideal high‐temperature material. In short, the as‐prepared PMIA/PAN‐MWCNT composite membrane with excellent comprehensive property emerges a promising application in many fields, especially in high‐tech.     

聚酯铵盐粉末发泡制备聚酰亚胺泡沫材料的研究

以芳香二酐和二胺为单体,采用聚酯铵盐前体粉末发泡的方法制备聚酰亚胺泡沫材料。考察了发泡温度、粉末大小对泡孔结构的影响。力学和热性能测试结果表明,该泡沫材料拉伸行为呈脆性,而压缩行为呈塑性,密度较大的聚酰亚胺泡沫表现出较好的力学性能。随着泡沫材料密度增大或测试温度升高,聚酰亚胺泡沫的导热系数增大。     

Synthesis and characterization of poly(acrylate amic acid) and its application as negative‐tone photosensitive polyimides

The dianhydride monomer 3,3′,4,4′‐benzophenone tetracarboxylic acid dianhydride and two diamine monomers, 4,4′‐diamino‐3,3′‐biphenyldiol (HAB) and 2,4‐diaminophenol dihydrochloride (DAP), were used to synthesize a series of poly(hydroxyl amic acid). Further functionalization by grafting acrylate groups yields the corresponding poly(acrylate amic acid) that underwent a crosslinking reaction on exposure to UV‐light and was used as a negative‐tone photosensitive polyimide (PSPI). The analysis of chemical composition and molecular weight of these poly(amic acid)s determined by nuclear magnetic resonance (NMR) spectroscopy, Fourier transform infrared spectroscopy, and gel permeation chromatography revealed that the molecular weight of the poly(hydroxyl amic acid) increased with the molar content of HAB in the feedstock, because HAB exhibited higher polymerization reactivity than DAP. Moreover, the degree of grafting acrylate groups onto poly(hydroxyl amic acid) was determined by ¹H‐NMR spectroscopy. The photoresist was formulated by adding 2‐benzyl‐2‐N,N‐dimethylamino‐1‐(4‐morpholinophenyl) butanone (IRG369) and isopropylthioxanthone as a photoinitiator, tetra(ethylene glycol) diacrylate as a crosslinker, and tribromomethyl phenyl sulfone as a photosensitizer. The PSPI precursor exhibited a photosensitivity of 200 mJ/cm² and a contrast of 1.78. A pattern with a resolution of 10 μm was observed in an optical micrograph after thermal imidization at 300°C. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Poly(amide imide)s and poly(amide imide) composite membranes by interfacial polymerization

Novel amic acid diamines (AADs) (2‐carboxyterephthalamido‐bis(alkyl or aryl amine)s, H₂N? X? NH(O?)C? C₆H₃(COOH)? C(?O)NH? X? NH₂, where X is were synthesized by reacting trimellitic anhydride chloride with aromatic or aliphatic diamines in dimethylformamide at 5–10 °C. Poly(amide imide)s (PAIs) with an amide to imide ratio of three in the polymer chains were prepared by interfacial polycondensation of the AADs in aqueous alkaline solution with isophthaloyl chloride or terephthaloyl chloride in dichloromethane at ambient temperature to form poly(amide amic acid)s, followed by their subsequent thermal cycloimidization. All of the PAIs were soluble in polar aprotic solvents such as dimethylformamide, dimethylacetamide, dimethyl sulfoxide and N‐methylpyrrolidone, and have inherent viscosities in the range 0.15–0.48 dL g^?1. The polymers were characterized by IR and NMR spectroscopy, TGA and DSC techniques. The PAIs have initial decomposition temperatures in the range 250–460 °C in air, and glass transition temperatures of 128–320 °C, depending upon the structures of the monomers. Composite membranes containing a poly(amide amic acid) and poly(amide imide) barrier layer on the top of a porous polyethersulfone support were prepared by in situ interfacial polymerization of the AADs in aqueous alkaline solution with trimesoyl chloride in hexane, and subsequent curing. The performances of these membranes were evaluated by using aqueous feed solutions containing 2000 ppm NaCl, Na₂SO₄ or CaCl₂. Copyright © 2006 Society of Chemical Industry     

静电纺丝制备苯乙烯马来酸酐共聚物纳米纤维及其固定化b-D-半乳糖苷酶

采用静电纺丝技术制备苯乙烯-马来酸酐共聚物纳米纤维,最佳电纺条件为：聚合物浓度0.35 g/mL、针尖到接收板距离25 cm、电纺液流量250 mL/h、电压21 kV. 该条件下获得了直径约300 nm且分布均一的纳米纤维. 利用该纳米纤维固定b-D-半乳糖苷酶,固定化反应的最适pH值为4.0,此时酶负载量为(15.1±0.5) mg/g. 固定化酶催化2-硝基苯酚-b-D-半乳吡喃糖苷水解反应的米氏常数Km=2.7 mmol/L,略大于游离酶的Km值(2.2 mmol/L);最大反应速率Vmax为97.2 mmol/(min×mg),为游离酶的47.8%. 固定化酶在37℃下重复操作21次后活性损失仅为15%. 在连续搅拌式反应器中将固定化酶用于催化乳糖的水解反应,连续使用17 d仍能稳定运行.     

橡实淀粉/聚乳酸复合材料的制备与结构性能研究

采用熔融挤出法制备了橡实淀粉 (AS)/聚乳酸 (PLA)二元复合材料。通过对复合材料力学性能、吸水性、熔融指数 (MIR)、扫描电镜 (SEM)、动态机械热分析 (DMA)和热稳定性 (TG)的测试,研究了橡实淀粉含量对复合材料的力学性能、疏水性能和热性能的影响。研究表明,随着AS加入量的增加,复合材料的刚性逐渐增强,在AS质量分散50%的情况下,拉伸强度仍达47.19 MPa。熔融流动性能、拉伸和弯曲强度则略微有所下降,其玻璃化转变温度略向高温偏移,保持在57 ℃。制备的复合材料具有优异的疏水性能,即使在AS加入量高达50%的情况下,接触角可达63.26°,吸水率仅为2.68%。     

Effect of film formation process on residual stress of poly(p-phenylene biphenyltetracarboximide) in thin films

Soluble poly(p-phenylene biphenyltetracarboxamine acid) (BPDA-PDA PAA) precursor, which was synthesized from biphenyltetracarboxylic dianhydride and p-phenylene diamine in N-methyl-2-pyrrolidone (NMP), was spin-cast on silicon substrates, followed by softbake at various conditions over 80–185°C. Softbaked films were converted in nitrogen atmosphere to be the polyimide films of ca. 10 μm thickness through various imidizations over 120–400°C. Residual stress, which is generated at the polymer/substrate interface by volume shrinkage, polymer chain ordering, thermal history, and differences between properties of the polymer film and the substrate, was measured in situ during softbake and subsequent imidization processes. Polymer films imidized were further characterized in the aspect of polymer chain orientation by prism coupling and X-ray diffraction. Residual stress in the polyimide film was very sensitive to all the film formation process parameters, such as softbake temperature and time, imidization temperature, imidization step, heating rate, and film thickness, but insensitive to the cooling process. Softbaked precursor films revealed 9–42 MPa at room temperature, depending on the softbake temperature and time. That is, residual stress in the precursor film was affected by the amount of residual solvent and by partial imidization possibly occurring during softbake above the onset of imidization temperature, ca. 130°C. A lower amount of residual solvent caused higher stress in the precursor film, whereas a higher degree of imidization led to lower stress. Partially imidized precursor films were converted to polyimide films revealing relatively high stresses. After imidization, polyimide films exhibited a wide range of residual stress, 4–43 MPa at room temperature, depending on the histories of softbake and imidization. Relatively high stresses were observed in the polyimide films which were prepared from softbaked films partially imidized and by rapid imidization process with a high heating rate. The residual stress in films is an in-plane characteristic so that it is sensitive to the degree of in-plane chain orientation in addition to the thermal history term. Low stress films exhibited higher degree of in-plane chain orientation. Thus, residual stress in the film would be controlled by the alignment of polyimide chains via the film formation process with varying process parameters. Conclusively, in order to minimize residual stress and to maximize in-plane chain orientation, precursor films should be softbaked for 30 min-2 h below the onset imidization temperature, ca. 130°C, and subsequently imidized over the range of 300–400°C for 1–4 h by a two-step or multi-step process with a heating rate of ? 5.0 K min⁻¹, including a step to cover the boiling point, 202°C, of NMP. In addition, the final thickness of the imidized films should be <20 μm. © 1997 Elsevier Science Ltd.     

Synthesis and Properties of Novel Poly(amide-imide)s Derived from 2,4-diaminotriphenylamine and Imide Ring-Preformed Dicarboxylic Acids

2,4-diaminotriphenylamine (2) was synthesized via the cesium fluoride-mediated aromatic substitution reaction of 1-fluoro-2,4-dinitrobenzene with diphenylamine, followed by palladium-catalyzed hydrazine reduction. A series of poly(amide-imide)s (PAIs) with inherent viscosities of 0.38–0.46 dL/g were prepared by triphenyl phosphite-activated polycondensation from the diamine monomer 2 with various monoimide- and diimide-dicarboxylic acids. All of the PAIs were readily soluble in a variety of organic solvents and formed strong and tough films via solution casting. These PAIs have moderately high glass transition temperatures in the range of 168–274 ^○C and 10 % weight loss temperatures in excess of 447 ^○C in nitrogen or in air.     

Fabrication of Uniaxially Aligned Poly(propylene) Nanofibers via Handspinning

A straightforward method, which is termed novel handspinning, is reported for producing uniaxially aligned sPP nanofibers. As demonstrated by SEM analysis, the morphologies of handspun sPP nanofibers are strongly dependent upon the processing conditions such as spinning method and solvent system. Compared to the normal electrospun sPP nanofibers, the handspun sPP nanofibers show smoother morphologies. FT‐IR analysis demonstrates a significant difference in polymer chain conformation between the handspun and electrospun sPP nanofibers. Moreover, interestingly, the handspun sPP single nanofibers show higher Young's modulus and tensile strength than electrospun sPP single nanofibers.

     

Dynamic Melt Rheological Properties of Ionomers Based on Poly(Ethylene-co-Acrylic Acid) and Poly(Ethylene-co-Methacrylic Acid)

The high temperature stability, and the dynamic melt rheological properties of poly(ethylene-co-acrylic acid) (EAA), zinc salt of EAA, and sodium salt of EAA were evaluated in the molten state over broad ranges of shear rates and temperatures using ARES (Rheometrics). The master curves of G′ and G″ as a function of angular frequency (ω) were constructed for each material. The influence of ionic groups on the storage modulus (G′), loss modulus (G″), complex viscosity (η*), and flow activation energy (E_a) were analyzed. The results of EAA based ionomers are discussed with those of the ionomers based on poly(ethylene-co-methacrylic acid) (EMAA). The linear visco-elastic spectra, and flow activation energies of the two series of ionomers show differences.     

Comparative Kinetic Study and Microwaves Non-Thermal Effects on the Formation of Poly(amic acid) 4,4'-(Hexafluoroisopropylidene)diphthalic Anhydride (6FDA) and 4,4'-(Hexafluoroisopropylidene)bis(p-phenyleneoxy)dianiline (BAPHF). Reaction Activated by Microwave, Ultrasound and Conventional Heating

Green chemistry is the design of chemical processes that reduce or eliminate negative environmental impacts. The use and production of chemicals involve the reduction of waste products, non-toxic components, and improved efficiency. Green chemistry applies innovative scientific solutions in the use of new reagents, catalysts and non-classical modes of activation such as ultrasounds or microwaves. Kinetic behavior and non-thermal effect of poly(amic acid) synthesized from (6FDA) dianhydride and (BAPHF) diamine in a low microwave absorbing p-dioxane solvent at low temperature of 30, 50, 70 °C were studied, under conventional heating (CH), microwave (MW) and ultrasound irradiation (US). Results show that the polycondensation rate decreases (MW > US > CH) and that the increased rates observed with US and MW are due to decreased activation energies of the Arrhenius equation. Rate constant for a chemical process activated by conventional heating declines proportionally as the induction time increases, however, this behavior is not observed under microwave and ultrasound activation. We can say that in addition to the thermal microwave effect, a non-thermal microwave effect is present in the system.     

Highly‐Aligned Electrospun Luminescent Nanofibers Prepared from Polyfluorene/PMMA Blends: Fabrication,Morphology, Photophysical Properties and Sensory Applications

Highly‐aligned luminescent electrospun nanofibers were successfully prepared from two binary blends of PFO/PMMA and PF⁺/PMMA. The PFO/PMMA aligned electrospun fibers showed a core/shell structure but the PF⁺/PMMA fibers exhibited periodic aggregate domains in the fibers. The aligned fibers had polarized steady‐state luminescence with a polarized ratio as high as 4, much higher than the non‐woven electrospun fibers or spin‐coated film. Besides, the PF⁺/PMMA aligned electrospun fibers showed an enhanced sensitivity to plasmid DNA. Such aligned electrospun fibers could have potential applications in optoelectronic or sensory devices.