Hydrogen production from steam reforming of methanol over CuO/ZnO/Al2O3 catalysts: Catalytic performance and kinetic modeling

A series of CuO/ZnO/Al_2O_3, CuO/ZnO/ZrO_2/Al_2O_3 and CuO/ZnO/CeO_2/Al_2O_3 catalysts were prepared by coprecipitation and characterized by N_2 adsorption, XRD, TPR, N_2O titration and HRTEM. The catalytic performances of these catalysts for the steam reforming of methanol were evaluated in a laboratory-scale fixed-bed reactor at 0.1 MPa and temperatures between 473 and 543 K. The results showed that the catalytic activity depended greatly on the catalyst reducibility and the specific surface area of Cu. An approximate linear correlation between the catalytic activity and the Cu surface area was found for all catalysts investigated in this study.Compared to CuO/ZnO/Al_2O_3, the ZrO_2-doped CuO/ZnO/Al_2O_3 exhibited higher activity and selectivity to CO,while the CeO_2-doped catalyst displayed lower activity and selectivity. Finally, an intrinsic kinetic study was carried out over a screened CuO/ZnO/CeO_2/Al_2O_3 catalyst in the absence of internal and external mass transfer effects. A good agreement was observed between the model-derived effluent concentrations of CO(CO_2) and the experimental data. The activation energies for the reactions of methanol-steam reforming, water-gas shift and methanol decomposition over CuO/ZnO/CeO_2/Al_2O_3 were 93.1, 85.1 and 116.5 k J·mol~(-1), respectively.     

Cu-Ce-O/γ-Al_2O_3的CO氧化性能

采用柠檬酸络合法制备一系列不同铜铈比的Cu-Ce-O/γ-Al_2O_3催化剂,用XRD、H2-TPR对其进行表征,采用连续固定床微反装置对Cu-Ce-O/γ-Al_2O_3催化剂CO催化氧化活性进行评价。结果表明,Cu-Ce-O/γ-Al_2O_3催化剂的XRD图谱中除归属于γ-Al_2O_3的晶相峰外,还出现CuO和CeO_2的晶相峰。高温水热引起活性组分CeO_2的晶粒聚集、长大和尖晶石结构CuAl2O4物质的生成;CuO-CeO_2之间的共生共存与相互作用,使得Cu-Ce-O/γ-Al_2O_3催化剂中具有非完整结构的[Cu2+1-xCu+x][O1-12x12x]增多,Cu+离子和氧空位增多,有利于其H2-TPR还原峰温度向低温区偏移,有利于提高其CO的催化氧化活性,使得Cu-Ce-O/γ-Al_2O_3催化剂的TCO50和TCO90降低。Cu与Ce物质的量比为5∶5制备的Cu-Ce-O/γ-Al_2O_3-55催化剂的TCO50和TCO90分别降至最低的162℃和199℃,表明此时的Cu-Ce-O协同效应最佳;CuO-CeO_2二相的共生共存与相互作用有利于减少高温水热环境下活性组分的聚集和晶粒长大,有利于Cu-Ce-O/γ-Al_2O_3催化剂能够保持较高的CO催化氧化活性。     

Comparison of catalytic activity and selectivity of Pd/(OSC + Al2O3) and (Pd + OSC)/Al2O3 catalysts

The effect of the Pd addition method into the fresh Pd/(OSC + Al₂O₃) and (Pd + OSC)/Al₂O₃ catalysts (OSC material = Ce_xZr_1−xO₂ mixed oxides) was investigated in this study. The CO + NO and CO + NO + O₂ model reactions were studied over fresh and aged catalysts. The differences in the fresh catalysts were insignificant compared to the aged catalysts. During the CO + NO reaction, only small differences were observed in the behaviour of the fresh catalysts. The light-off temperature of CO was about 20 °C lower for the fresh Pd/(OSC + Al₂O₃) catalyst than for the fresh (Pd + OSC)/Al₂O₃ catalyst during the CO + NO + O₂ reaction. For the aged catalysts lower NO reduction and CO oxidation activities were observed, as expected. Pd on OSC-containing alumina was more active than Pd on OSC material after the agings. The activity decline is due to a decrease in the number of active sites on the surface, which was observed as a larger Pd particle size for aged catalysts than for fresh catalysts. In addition, the oxygen storage capacity of the aged Pd/(OSC + Al₂O₃) catalyst was higher than that of the (Pd + OSC)/Al₂O₃ catalyst.     

Oxides of copper, ceria promoted copper, manganese and copper manganese on Al2O3 for the combustion of CO, ethyl acetate and ethanol

Combustion of CO, ethyl acetate and ethanol was studied over CuO_x/Al₂O₃, CuO_x–CeO₂/Al₂O₃, CuMn₂O₄/Al₂O₃ and Mn₂O₃/Al₂O₃ catalysts. It was found that modification of the alumina with ceria before subsequent copper oxide deposition increases the activity for combustion of CO substantially, but the effect of ceria was small on the combustion of ethyl acetate and ethanol. The activity increases with the CuO_x loading until crystalline CuO particles are formed, which contribute little to the total active surface. The CuO_x–CeO₂/Al₂O₃ catalyst is more active than the CuMn₂O₄/Al₂O₃ catalyst for the oxidation of CO but the CuMn₂O₄/Al₂O₃ catalyst is more active for the combustion of ethyl acetate and ethanol.

Thermal ageing and water vapour in the feed caused a modest decrease in activity and did not affect the CuO_x–CeO₂/Al₂O₃ and CuMn₂O₄/Al₂O₃ catalysts differently. In addition, no difference in intermediates formed over the two catalysts was observed.

Characterisation with XRD, FT-Raman and TPR indicates that the copper oxide is present as a copper aluminate surface phase on alumina at low loading. At high loading, bulk CuO crystallites are present as well. Modification of the alumina with ceria before the copper oxide deposition gives well dispersed copper oxide species and bulk CuO crystallites associated to the ceria, in addition to the two copper oxide species on the bare alumina. The distribution of copper species depends on the ceria and copper oxide loading. The alumina supported copper manganese oxide and manganese oxide catalysts consist mainly of crystalline CuMn₂O₄ and Mn₂O₃, respectively, on Al₂O₃.     

Catalytic reduction of NO by CO over NiO/CeO2 catalyst in stoichiometric NO/CO and NO/CO/O2 reaction

A new catalyst composed of nickel oxide and cerium oxide was studied with respect to its activity for NO reduction by CO under stoichiometric conditions in the absence as well as the presence of oxygen. Activity measurements of the NO/CO reaction were also conducted over NiO/γ-Al₂O₃, NiO/TiO₂, and NiO/CeO₂ catalysts for comparison purposes. The results showed that the conversion of NO and CO are dependent on the nature of supports, and the catalysts decreased in activity in the order of NiO/CeO₂ > NiO/γ-Al₂O₃ > NiO/TiO₂. Three kinds of CeO₂ were prepared and used as support for NiO. They are the CeO₂ prepared by (i) homogeneous precipitation (HP), (ii) precipitation (PC), and (iii) direct decomposition (DP) method. We found that the NiO/CeO₂(HP) catalyst was the most active, and complete conversion of NO and CO occurred at 210 °C at a space velocity of 120,000 h⁻¹. Based on the results of surface analysis, a reaction model for NO/CO interaction over NiO/CeO₂ has been proposed: (i) CO reduces surface oxygen to create vacant sites; (ii) on the vacant sites, NO dissociates to produce N₂; and (iii) the oxygen originated from NO dissociation is removed by CO.     

MnOx/Pt/Al2O3 catalysts for CO oxidation in H2-rich streams

The catalytic activity of Pt on alumina catalysts, with and without MnO_x incorporated to the catalyst formulation, for CO oxidation in H₂-free as well as in H₂-rich stream (PROX) has been studied in the temperature range of 25–250 °C. The effect of catalyst preparation (by successive impregnation or by co-impregnation of Mn and Pt) and Mn content in the catalyst performance has been studied. A low Mn content (2 wt.%) has been found not to improve the catalyst activity compared to the base catalyst. However, catalysts prepared by successive impregnation with 8 and 15 wt.% Mn have shown a lower operation temperature for maximum CO conversion than the base catalyst with an enhanced catalyst activity at low temperatures with respect to Pt/Al₂O₃. A maximum CO conversion of 89.8%, with selectivity of 44.9% and CO yield of 40.3% could be reached over a catalyst with 15 wt.% Mn operating at 139 °C and λ = 2. The effect of the presence of 5 vol.% CO₂ and 5 vol.% H₂O in the feedstream on catalysts performance has also been studied and discussed. The presence of CO₂ in the feedstream enhances the catalytic performance of all the studied catalysts at high temperature, whereas the presence of steam inhibits catalysts with higher MnO_x content.     

Design of a novel bifunctional catalyst IrFe/Al2O3 for preferential CO oxidation

In this study, a novel bifunctional catalyst IrFe/Al₂O₃, which is very active and selective for preferential oxidation of CO under H₂-rich atmosphere, has been developed. When the molar ratio of Fe/Ir was 5/1, the IrFe/Al₂O₃ catalyst performed best, with CO conversion of 68% and oxygen selectivity towards CO₂ formation of 86.8% attained at 100 °C. It has also been found that the impregnation sequence of Ir and Fe species on the Al₂O₃ support had a remarkable effect on the catalytic performance; the activity decreased following the order of IrFe/Al₂O₃ > co-IrFe/Al₂O₃ > FeIr/Al₂O₃. The three catalysts were characterized by XRD, H₂-TPR, FT-IR and microcalorimetry. The results demonstrated that when Ir was supported on the pre-formed Fe/Al₂O₃, the resulting structure (IrFe/Al₂O₃) allowed more metallic Ir sites exposed on the surface and accessible for CO adsorption, while did not interfere with the O₂ activation on the FeO_x species. Thus, a bifunctional catalytic mechanism has been proposed where CO adsorbed on Ir sites and O₂ adsorbed on FeO_x sites; the reaction may take place at the interface of Ir and FeO_x or via a spill-over process.     

Catalytic decomposition of N2O over CeO2 promoted Co3O4 spinel catalyst

A series of CeO₂ promoted cobalt spinel catalysts were prepared by the co-precipitation method and tested for the decomposition of nitrous oxide (N₂O). Addition of CeO₂ to Co₃O₄ led to an improvement in the catalytic activity for N₂O decomposition. The catalyst was most active when the molar ratio of Ce/Co was around 0.05. Complete N₂O conversion could be attained over the CoCe0.05 catalyst below 400 °C even in the presence of O₂, H₂O or NO. Methods of XRD, FE-SEM, BET, XPS, H₂-TPR and O₂-TPD were used to characterize these catalysts. The analytical results indicated that the addition of CeO₂ could increase the surface area of Co₃O₄, and then improve the reduction of Co³⁺ to Co²⁺ by facilitating the desorption of adsorbed oxygen species, which is the rate-determining step of the N₂O decomposition over cobalt spinel catalyst. We conclude that these effects, caused by the addition of CeO₂, are responsible for the enhancement of catalytic activity of Co₃O₄.     

Role of CeO2 in Ni/CeO2–Al2O3 catalysts for carbon dioxide reforming of methane

Ni catalysts supported on γ-Al₂O₃, CeO₂ and CeO₂–Al₂O₃ systems were tested for catalytic CO₂ reforming of methane into synthesis gas. Ni/CeO₂–Al₂O₃ catalysts showed much better catalytic performance than either CeO₂- or γ-Al₂O₃-supported Ni catalysts. CeO₂ as a support for Ni catalysts produced a strong metal–support interaction (SMSI), which reduced the catalytic activity and carbon deposition. However, CeO₂ had positive effect on catalytic activity, stability, and carbon suppression when used as a promoter in Ni/γ-Al₂O₃ catalysts for this reaction. A weight loading of 1–5 wt% CeO₂ was found to be the optimum. Ni catalysts with CeO₂ promoters reduced the chemical interaction between nickel and support, resulting in an increase in reducibility and stronger dispersion of nickel. The stability and less coking on CeO₂-promoted catalysts are attributed to the oxidative properties of CeO₂.     

K-, CeO2-, and Mn-promoted Ni/Al2O3 catalysts for stable CO2 reforming of methane

Reforming of methane with carbon dioxide into syngas over Ni/γ-Al₂O₃ catalysts modified by potassium, MnO and CeO₂ was studied. The catalysts were prepared by impregnation technique and were characterized by N₂ adsorption/desorption isotherm, BET surface area, pore volume, and BJH pore size distribution measurements, and by X-ray diffraction and scanning electron microscopy. The performance of these catalysts was evaluated by conducting the reforming reaction in a fixed bed reactor. The coke content of the catalysts was determined by oxidation conducted in a thermo-gravimetric analyzer. Incorporation of potassium and CeO₂ (or MnO) onto the catalyst significantly reduced the coke formation without significantly affecting the methane conversion and hydrogen yield. The stability and the lower amount of coking on promoted catalysts were attributed to partial coverage of the surface of nickel by patches of promoters and to their increased CO₂ adsorption, forming a surface reactive carbonate species. Addition of CeO₂ or MnO reduced the particle size of nickel, thus increasing Ni dispersion. For Ni–K/CeO₂–Al₂O₃ catalysts, the improved stability was further attributed to the oxidative properties of CeO₂. Results of the investigation suggest that stable Ni/Al₂O₃ catalysts for the carbon dioxide reforming of methane can be prepared by addition of both potassium and CeO₂ (or MnO) as promoters.     

Fischer–Tropsch synthesis over Re-promoted Co supported on Al2O3, SiO2 and TiO2: Effect of water

The activity and selectivity of rhenium promoted cobalt Fischer–Tropsch catalysts supported on Al₂O₃, TiO₂ and SiO₂ have been studied in a fixed-bed reactor at 483 K and 20 bar. Exposure of the catalysts to water added to the feed deactivates the Al₂O₃ supported catalyst, while the activity of the TiO₂ and SiO₂ supported catalysts increased. However, at high concentrations of water both the SiO₂ and TiO₂ supported catalyst deactivated. Common for all catalysts was an increase in C₅₊ selectivity and a decrease in the CH₄ selectivity by increasing the water partial pressure. The catalysts have been characterized by scanning transmission electron microscope (STEM), BET, H₂ chemisorption and X-ray diffraction (XRD).     

Ultrahigh temperature water gas shift catalysts to increase hydrogen yield from biomass gasification

Noble metal (Rh, Pt, Pd, Ir, Ru, and Ag) and Ni catalysts supported on CeO₂–Al₂O₃ were investigated for water gas shift reaction at ultrahigh temperatures. Pt/CeO₂–Al₂O₃ and Ru/CeO₂–Al₂O₃ demonstrated as the best catalysts in terms of activity, hydrogen yield and hydrogen selectivity. At 700 °C and steam to CO ratio of 5.2:1, Pt/CeO₂–Al₂O₃ converted 76.3% of CO with 94.7% of hydrogen selectivity. At the same conditions, the activity and hydrogen selectivity for Ru/CeO₂–Al₂O₃ were 63.9% and 85.6%, respectively. Both catalysts showed a good stability over 9 h of continuous operation. However, both catalysts showed slight deactivation during the test period. The study revealed that Pt/CeO₂–Al₂O₃ and Ru/CeO₂–Al₂O₃ were excellent ultrahigh temperature water gas shift catalysts, which can be coupled with biomass gasification in a downstream reactor.     

The role of lanthana loading on the catalytic properties of Pd/Al2O3-La2O3 in the NO reduction with H2

The role of La₂O₃ loading in Pd/Al₂O₃-La₂O₃ prepared by sol–gel on the catalytic properties in the NO reduction with H₂ was studied. The catalysts were characterized by N₂ physisorption, temperature-programmed reduction, differential thermal analysis, temperature-programmed oxidation and temperature-programmed desorption of NO.

The physicochemical properties of Pd catalysts as well as the catalytic activity and selectivity are modified by La₂O₃ inclusion. The selectivity depends on the NO/H₂ molar ratio (GHSV = 72,000 h⁻¹) and the extent of interaction between Pd and La₂O₃. At NO/H₂ = 0.5, the catalysts show high N₂ selectivity (60–75%) at temperatures lower than 250 °C. For NO/H₂ = 1, the N₂ selectivity is almost 100% mainly for high temperatures, and even in the presence of 10% H₂O vapor. The high N₂ selectivity indicates a high capability of the catalysts to dissociate NO upon adsorption. This property is attributed to the creation of new adsorption sites through the formation of a surface PdO_x phase interacting with La₂O₃. The formation of this phase is favored by the spreading of PdO promoted by La₂O₃. DTA shows that the phase transformation takes place at temperatures of 280–350 °C, while TPO indicates that this phase transformation is related to the oxidation process of PdO: in the case of Pd/Al₂O₃ the O₂ uptake is consistent with the oxidation of PdO to PdO₂, and when La₂O₃ is present the O₂ uptake exceeds that amount (1.5 times). La₂O₃ in Pd catalysts promotes also the oxidation of Pd and dissociative adsorption of NO mainly at low temperatures (<250 °C) favoring the formation of N₂.     

NO reduction by CH4 in the presence of O2 over La2O3 supported on Al2O3

Dispersing La₂O₃ on δ- or γ-Al₂O₃ significantly enhances the rate of NO reduction by CH₄ in 1% O₂, compared to unsupported La₂O₃. Typically, no bend-over in activity occurs between 500° and 700°C, and the rate at 700°C is 60% higher than that with a Co/ZSM-5 catalyst. The final activity was dependent upon the La₂O₃ precursor used, the pretreatment, and the La₂O₃ loading. The most active family of catalysts consisted of La₂O₃ on γ-Al₂O₃ prepared with lanthanum acetate and calcined at 750°C for 10 h. A maximum in rate (mol/s/g) and specific activity (mol/s/m²) occurred between the addition of one and two theoretical monolayers of La₂O₃ on the γ-Al₂O₃ surface. The best catalyst, 40% La₂O₃/γ-Al₂O₃, had a turnover frequency at 700°C of 0.05 s⁻¹, based on NO chemisorption at 25°C, which was 15 times higher than that for Co/ZSM-5. These La₂O₃/Al₂O₃ catalysts exhibited stable activity under high conversion conditions as well as high CH₄ selectivity (CH₄ + NO vs. CH₄ + O₂). The addition of Sr to a 20% La₂O₃/γ-Al₂O₃ sample increased activity, and a maximum rate enhancement of 45% was obtained at a SrO loading of 5%. In contrast, addition of SO⁼₄ to the latter Sr-promoted La₂O₃/Al₂O₃ catalyst decreased activity although sulfate increased the activity of Sr-promoted La₂O₃. Dispersing La₂O₃ on SiO₂ produced catalysts with extremely low specific activities, and rates were even lower than with pure La₂O₃. This is presumably due to water sensitivity and silicate formation. The La₂O₃/Al₂O₃ catalysts are anticipated to show sufficient hydrothermal stability to allow their use in certain high-temperature applications.     

On the mechanism of model diesel soot-O2 reaction catalysed by Pt-containing La-doped CeO2: A TAP study with isotopic O2

Pt supported on CeO₂ and 10 wt.% La³⁺-doped CeO₂ catalysts have been prepared, characterised and tested for soot oxidation by O₂ in TGA. The reaction mechanism has been studied in a TAP reactor with labelled O₂. Isotopic oxygen exchange between molecular O₂ and ‘O’ on the support/catalyst was observed and soot oxidation is being carried out by lattice oxygen. TAP studies further show that Pt improves O₂ adsorption and, therefore, 5 wt.% Pt-containing catalysts are more active for soot oxidation than the counterpart supports. In addition, CeO₂ doping by La³⁺ leads to an improved support, since La³⁺ stabilises the structure of CeO₂ when calcined at high temperature (1000 °C) and minimises sintering. In addition, La³⁺ improves the Ce⁴⁺/Ce³⁺ reduction as deduced from H₂-TPR experiments and favours oxygen mobility into the lattice. A synergetic effect of Pt and La³⁺ is observed, Pt-containing La³⁺-doped CeO₂ being the most active catalyst for soot oxidation by O₂ among the samples studied.     

Hydrogenation of naphthalene on NiMo- Ni- and Ru/Al2O3 catalysts: Langmuir–Hinshelwood kinetic modelling

The importance of the hydrodearomatisation (HDA) is increasing together with tightening legislation of fuel quality and exhaust emissions. The present study focuses on hydrogenation (HYD) kinetics of the model aromatic compound naphthalene, found in typical diesel fraction, in n-hexadecane over a NiMo (nickel molybdenum), Ni (nickel) and Ru (ruthenium) supported on trilobe alumina (Al₂O₃) catalysts. Kinetic reaction expressions based on the mechanistic Langmuir–Hinshelwood (L–H) model were derived and tested by regressing the experimental data that translated the effect of both naphthalene and hydrogen concentration at a constant temperature (523.15 and 573.15 K over the NiMo catalyst and at 373.15 K over the Ni and Ru/Al₂O₃ catalysts) on the initial reaction rate. The L–H equation, giving an adequate fit to the experimental data with physically meaningful parameters, suggested a competitive adsorption between hydrogen and naphthalene over the presulphided NiMo catalyst and a non-competitive adsorption between these two reactants over the prereduced Ni and Ru/Al₂O₃ catalysts. In addition, the adsorption constant values indicated that the prereduced Ru catalyst was a much more active catalyst towards naphthalene HYD than the prereduced Ni/Al₂O₃ or the presulphided NiMo/Al₂O₃ catalyst.     

CeO2改性Ni/γ-Al2O3催化剂上顺酐加氢制备丁二酸酐

采用等体积浸渍法制备CeO₂改性Ni/γ-Al₂O₃催化剂,通过BET、XRD、H₂-TPR和SEM等对催化剂结构及物化性能进行表征,考察Ni-CeO₂/γ-Al₂O₃催化剂对顺酐催化加氢制备丁二酸酐催化性能的影响。结果表明,引入适量CeO₂可提高催化剂活性组分Ni的分散度,增加催化剂比表面积,提高催化剂热稳定性。采用负载CeO₂质量分数5%的Ni-CeO₂/γ-Al₂O₃催化剂,在反应温度120 ℃、反应压力2.0 MPa和空速0.6 h^-1条件下,顺酐转化率为99.5%,丁二酸酐选择性为99.4%。     

Steam reforming of ethanol over Co3O4/CeO2 catalysts prepared by different methods

In this paper, Co₃O₄/CeO₂ catalysts for steam reforming of ethanol (SRE) were prepared by co-precipitation and impregnation methods. The catalysts prepared by co-precipitation were very active and selective for SRE. Over 10%Co₃O₄/CeO₂ catalyst, ethanol conversion was close to 100% and hydrogen selectivity was about 70% at 450 °C. The catalysts were characterized by X-ray diffraction, temperature-programmed reduction (TPR) and BET surface area measurements. The preparation method influenced the interaction between cobalt and CeO₂ evidently. The incorporation of Co ions into CeO₂ crystal lattice resulted in weaker interaction between cobalt and ceria on catalyst surface. In comparison with catalysts prepared by impregnation, more cobalt ions entered into CeO₂ lattice, and resulted in weaker interaction between active phase and ceria on surface of Co₃O₄/CeO₂ prepared by co-precipitation. Thus, cobalt oxides was easier to be reduced to metal cobalt which was the key active component for SRE. Meanwhile, the incorporation of Co ions into CeO₂ crystal lattice was beneficial for resistance to carbon deposition.     

Total oxidation of propene and propane over gold–copper oxide on alumina catalysts: Comparison with Pt/Al2O3

Oxidation of propene and propane to CO₂ and H₂O has been studied over Au/Al₂O₃ and two different Au/CuO/Al₂O₃ (4 wt.% Au and 7.4 wt.% Au) catalysts and compared with the catalytic behaviour of Au/Co₃O₄/Al₂O₃ (4.1 wt.% Au) and Pt/Al₂O₃ (4.8 wt.% Pt) catalysts. The various characterization techniques employed (XRD, HRTEM, TPR and DR-UV–vis) revealed the presence of metallic gold, along with a highly dispersed CuO (6 wt.% CuO), or more crystalline CuO phase (12 wt.% CuO).

A higher CuO loading does not significantly influence the catalytic performance of the catalyst in propene oxidation, the gold loading appears to be more important. Moreover, it was found that 7.4Au/CuO/Al₂O₃ is almost as active as Pt/Al₂O₃, whereas Au/Co₃O₄/Al₂O₃ performs less than any of the CuO-containing gold-based catalysts.

The light-off temperature for C₃H₈ oxidation is significantly higher than for C₃H₆. For this reaction the particle size effect appears to prevail over the effect of gold loading. The most active catalysts are 4Au/CuO/Al₂O₃ (gold particles less than 3 nm) and 4Au/Co₃O₄/Al₂O₃ (gold particles less than 5 nm).     

ZrO2/SiO2- and La2O3/Al2O3-supported platinum catalysts for CH4/CO2 reforming

Surface-phase ZrO₂ on SiO₂ (SZrOs) and surface-phase La₂O₃ on Al₂O₃ (SLaOs) were prepared with various loadings of ZrO₂ and La₂O₃, characterized and used as supports for preparing Pt/SZrOs and Pt/SLaOs catalysts. CH₄/CO₂ reforming over the Pt/SZrOs and Pt/SLaOs catalysts was examined and compared with Pt/Al₂O₃ and Pt/SiO₂ catalysts. CO₂ or CH₄ pulse reaction/adsorption analysis was employed to elucidate the effects of these surface-phase oxides.

The zirconia can be homogeneously dispersed on SiO₂ to form a stable surface-phase oxide. The lanthana cannot be spread well on Al₂O₃, but it forms a stable amorphous oxide with Al₂O₃. The Pt/SZrOs and Pt/SLaOs catalysts showed higher steady activity than did Pt/SiO₂ and Pt/Al₂O₃ by a factor of three to four. The Pt/SZrOs and Pt/SLaOs catalysts were also much more stable than the Pt/SiO₂ and Pt/Al₂O₃ catalysts for long stream time and for reforming temperatures above 700 °C. These findings were attributed to the activation of CO₂ adsorbed on the basic sites of SZrOs and SLaOs.