Characterization of polyacrylonitrile,poly(acrylonitrile‐co‐vinyl acetate), and poly(acrylonitrile‐co‐itaconic acid) based activated carbon nanofibers

In this study, three different acrylonitrile (AN)‐based polymers, including polyacrylonitrile (PAN), poly(acrylonitrile‐co‐vinyl acetate) [P(AN‐co‐VAc)], and poly(acrylonitrile‐co‐itaconic acid) [P(AN‐co‐IA)], were used as precursors to synthesize activated carbon nanofibers (ACNFs). An electrospinning method was used to produce nanofibers. Oxidative stabilization, carbonization, and finally, activation through a specific heating regimen were applied to the electrospun fibers to produce ACNFs. Stabilization, carbonization, and activation were carried out at 230, 600, and 750 °C, respectively. Scanning electron microscopy, thermogravimetric analysis (TGA), and porosimetry were used to characterize the fibers in each step. According to the fiber diameter variation measurements, the pore extension procedure overcame the shrinkage of the fibers with copolymer precursors. However, the shrinkage process dominated the scene for the PAN homopolymer, and this led to an increase in the fiber diameter. The 328 m²/g Brunauer–Emmett–Teller surface area for ACNFs with PAN precursor were augmented to 614 and 564 m²/g for P(AN‐co‐VAc) and P(AN‐co‐IA), respectively. The TGA results show that the P(AN‐co‐IA)‐based ACNFs exhibited a higher thermal durability in comparison to the fibers of PAN and P(AN‐co‐VAc). The application of these copolymers instead of AN homopolymer enhanced the thermal stability and increased the surface area of the ACNFs even in low‐temperature carbonization and activation processes. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44381.     

Conducting poly(styrene‐co‐divinylbenzene)/polypyrrole PolyHIPE composite foam prepared by chemical oxidative polymerization

Conducting poly(styrene‐co‐divinylbenzene)/polypyrrole (PPy) polyHIPE (polymerized high internal phase emulsion) composite foams were synthesized via chemical oxidative polymerization method. The effect of solvent and dopant type on the surface morphology and electrical conductivity of composite foams has been investigated. SEM micrographs showed that the morphology of PPy thin film on the internal surface of poly(styrene/divinylbenzene) (poly(St‐co‐DVB) polyHIPE support foam strongly depends on the solvent and dopant type used. Incorporation of dodecylbenzene solfunic acid‐sodium salt (DBSNa) as a dopant in chloroform solvent resulted in formation of a PPy thin film with higher molecular compact structure and electrical conductivity on the support foam as compared to other solvents and another dopant used. Fourier‐transform infrared spectroscopy was used to correlate the electrical conductivity of composite foams to their PPy structural parameters. As expected, the extended conjugation length of PPy in the presence of DBSNa dopant is the main reason for higher electrical conductivity of resultant composite foam. Electrical conductivity measurements revealed that the chemical aging of various conducting foams follows the first‐order kinetic model, which is a representative of a reaction‐controlled aging mechanism. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Poly(glycidyl methacrylate‐co‐3‐thienyl‐methylmethacrylate) based working electrodes for hydrogen peroxide biosensing

BACKGROUND: Hydrogen peroxide biosensors based on Poly(glycidyl methacrylate‐co‐3‐thienylmethylmethacrylate)/ Polypyrrole [Poly(GMA‐co‐MTM)/PPy] composite film were reported. Poly(GMA‐co‐MTM) including various amounts of GMA and MTM monomers was synthesized via the radical polymerization. Enzyme horseradish peroxidase (HRP) was trapped in Poly(GMA‐co‐MTM)/PPy composites during the electropolymerization reaction between pyrrole and thiophene groups of MTM monomer, and chemically bonded via the epoxy groups of GMA. Analytical parameters of the fabricated electrodes were calculated and are discussed in terms of film electroactivity and mass transfer conditions of the composite films. RESULTS: The amount of electroactive HRP was found to be 1.25, 0.34 and 0.213 µg for the working electrodes of Poly(GMA_30%‐ co‐MTM_70%)/PPy/HRP, Poly(GMA_85%‐co‐MTM_15%)/PPy/HRP and Poly(GMA_90%‐co‐MTM_10%)/PPy/HRP, respectively. Optimal response of the fabricated electrodes was obtained at pH 7 and an operational potential of ? 0.35 V. It was observed that effective enzyme immobilization and electroactivity of the composite films could be changed by changing the ratios of GMA and MTM fractions of Poly(GMA‐co‐MTM) based working electrodes. CONCLUSION: The amount of electroactive enzyme increases with increasing MTM content of the final copolymer. High operational stabilities of the biosensors can be attributed to the strong covalent enzyme linkage via the epoxy groups of GMA due to preventing enzyme deterioration and loss. A more convenient microenvironment for mass transfer was provided for the electrodes by higher GMA ratios. It is observed that mass transfer is dominated by the mechanism of electron transfer to obtain effective sensitivity values. This work contributes to discussions clarifying the problems regarding the design parameters of biosensors. Copyright © 2011 Society of Chemical Industry     

Polymer nanocomposites containing carbon nanotubes and miscible polymer blends based on poly[ethylene‐co‐(acrylic acid)]

Four binary polymer blends containing poly [ethylene‐co‐(acrylic acid)] (PEAA) as one component, and poly(4‐vinyl phenol‐co‐2‐hydroxy ethyl methacrylate) (P4VPh‐co‐2HEMA) or poly(2‐ethyl‐2‐oxazoline) (PEOx) or poly(vinyl acetate‐co‐vinyl alcohol) (PVAc‐co‐VA) or poly (vinylpyrrolidone‐co‐vinyl acetate) (PVP‐co‐VAc) as the other component were prepared and used as a matrix of a series of composite materials. These binary mixtures were either partially or completely miscible within the composition range studied and were characterized by differential scanning calorimetry (DSC) and Fourier transformed infrared spectroscopy (FTIR). Carbon nanotubes (CNTs) were prepared by a thermal treatment of polyester synthesized through the chemical reaction between ethylene glycol and citric acid over an alumina boat. High resolution transmission electron microscopy (HRTEM) was used to characterize the synthesized CNTs. Films of composite materials containing CNTs were obtained after evaporation of the solvent used to prepare solutions of the four types of binary polymer blends. Young's moduli of the composites were obtained by thermomechanical analysis at room temperature. Only one glass transition temperature was detected for several compositions on both binary blends and the composite material matrices. Evidence of hydrogen bond formation was recorded for both miscible blends and composite materials. The degree of crystallinity and Young's moduli of the CNT‐polymer composites increased compared to the single polymer blends. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Dispersion of multiwalled carbon nanotubes in polyacrylonitrile‐co‐starch copolymer matrix for enhancement of electrical,thermal, and gas barrier properties

Nanomaterials gained great importance on account of their wide range of applications in many areas. Carbon nanotubes (CNTs) exhibit exceptional electrical, thermal, gas barrier, and tensile properties and can therefore be used for the development of a new generation of composite materials. Functionalized multiwalled carbon nanotubes (MWCNTs) reinforced Polyacrylonitrile‐co‐starch nanocomposites were prepared by in situ polymerization technique. The structural property of PAN‐co‐starch/MWCNT nanocomposites was studied by X‐ray diffraction, scanning electron microscopy, and transmission electron microscopy. The conductivity, tensile strength, and thermal properties of nanocomposites were measured as a function of MWCNT concentrations. The thermal stability, conductivity, and tensile strength of PAN‐co‐starch/MWCNT nanocomposites were improved with increasing concentration of MWCNTs. Oxygen barrier property of PAN‐co‐starch/MWCNT nanocomposites was calculated and it was found that, the property was reduced substantially with increase of MWCNTs proportion. The synthesized PAN‐co‐starch/MWCNT nanocomposites may used for electrostatically dissipative materials, aerospace or sporting goods, and electronic materials. © 2013 Society of Plastics Engineers     

Polymerization of lactams, 95 Preparation of polyesteramides by the anionic polymerization of ε-caprolactam in the presence of poly(ε-caprolactone)

Preparation of polyesteramides-poly[(ε-caprolactam)-co-(ε-caprolactone)]s by anionic polymerization of ε-caprolactam in the presence of poly(ε-caprolactone) at 150 °C was studied in this paper. ε-Caprolactam magnesium bromide was used as an initiator of polymerization and polymeric materials containing 5-25 wt% ε-caprolactone units were obtained. Thermal methods (DSC and DMA) were employed for characterization of poly[(ε-caprolactam)-co-(ε-caprolactone)]s and their mechanical properties were also evaluated. By introducing the activator with N-acyllactam structure, the polymerization rate increased and it was possible to carry out the polymerization at 110 °C. Mechanical properties of polyesteramides were influenced by both the content of ε-caprolactone units incorporated into copolymer and polymerization temperature. The mechanism of incorporation of poly(ε-caprolactone) is discussed. The results show that it is not possible to restrict exchange transacylation reactions, progressing in the course of polymerization, by kinetic tools.     

Acrylonitrile/vinyl acetate copolymer nanofibers with different vinylacetate content

In this study, free radical copolymerization of acrylonitrile (AN)–vinyl acetate (VAc) was performed for five different feed ratio of VAc (wt %) by using ammonium persulfate (APS) in the aqueous medium. The effect of VAc content on the spectrophotometric and thermal properties of AN–VAc copolymers was investigated by Fourier Transform Infrared–Attenuated Total Reflectance spectrophotometer (FTIR–ATR), differential scanning calorimeter (DSC), and thermal gravimetric analyzer (TGA). Thermal stability of homopolymer of AN is improved after being copolymerized. The electrospun P(AN‐co‐VAc) nanofibers were fabricated and the effect of VAc content on the morphologic properties of nanofibers was studied by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The viscosity of the solution had a significant effect on P(AN‐co‐VAc) electrospinning and the nanofiber morphology. The average diameters of P(AN‐co‐VAc) nanofibers decreased 3.4 times with increasing feed ratio of VAc wt %. The P(AN‐co‐VAc) electrospun nanofiber mats, with the feed ratio of 30 wt % VAc, can be used as a nanofiber membrane in filtration and as a carbon nanofiber precursor for energy storage applications due to high surface to volume ratio, high thermal stability, homogeneous, and thinner nanofiber distribution. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Electrical actuation of ionic hydrogels based on polyvinyl alcohol grafted with poly(2‐acrylamido‐2‐methyl‐1‐propanesulfonic acid‐co‐acrylonitrile) chains

Novel electrically conducting composite materials consisting of poly(pyrrole) (PPy) nanoparticles dispersed in a poly(vinyl alcohol)‐g‐poly(2‐acrylamido‐2‐methyl‐1‐propanesulfonic acid‐co‐acrylonitrile) hydrogels were prepared within the polymer matrix by in situ polymerization of pyrrole. The conversion yield of pyrrole into PPy particles was determined gravimetrically while structural confirmation of the synthesized polymer was sought by Fourier Transform Infrared (FTIR) and UV‐visible spectroscopy. The morphology of PPy nanoparticles containing hydrogel matrix was investigated by Scanning Electron Microscopy (SEM) analysis. Electrical conductivity of nanocomposite hydrogels of different compositions was determined by LCR meter while electroactive behavior of nanocomposite hydrogels swollen in electrolyte solutions was investigated by effective bend angle measurements. POLYM. COMPOS., 2012. © 2011 Society of Plastics Engineers     

Electrically conducting biodegradable polymer composites (polylactide‐polypyrrole and polycaprolactone‐polypyrrole) for passive resonant circuits

Electrically conducting biodegradable polymer composites made of polypyrrole (PPy) nanoparticles embedded in poly(L ‐lactide) (PLLA) or poly(ε‐caprolactone) (PCL) are prepared by chemical oxidative polymerization. They will be used as electrical conductors for fabricating biodegradable passive resonant circuits for bioimplants. For both composites, the conductivity exhibits a percolation threshold at ～6 wt% of PPy. Several reactants are tested, the polymerization process resulting in the highest conductivity uses iron(III)chloride hexahydrate (FeCl₃), sodium dodecyl benzene sulfonate, and p‐nitrophenol (pNPh), for both poly(L ‐lactide)‐polypyrrole (PLLA‐PPy) and poly(ε‐caprolactone)‐polypyrrole (PCL‐PPy). Conductivities of 2.7 ± 0.8 S cm^ε1 (PLLA‐PPy) and 7.8 ± 2.3 S cm^?1 (PCL‐PPy) are reached for a PPy content of 40 wt%. The PPy particle, observed by SEM, forms agglomerates having a size of 0.6–3.5 μm. The samples have similar PPy particle distributions over the entire cross sections. The conductivity as a function of time is investigated, being 34–70% of the initial value for samples stored in nitrogen, whereas it is less than 1% for samples stored in body‐like conditions, bringing the conclusion that a biodegradable packaging will be required to protect the resonant circuits from body fluids. Finally, the biocompatibility of the polymer composites is evaluated with cytocompatibility tests on dermal human fibroblast cells, showing promising results in particular for composites having a low PPy content. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Conducting polypyrrole‐coated banana fiber composites: Preparation and characterization

In this study, conducting banana fibers (BF) were obtained through in situ oxidative polymerization of pyrrole (Py) on the BF surface using ferric chloride hexahydratate (FeCl₃·6H₂O) as an oxidant. Suitable reaction conditions are outlined for the polymerization of Py: oxidant/monomer molar ratio, Py concentration and polymerization time of 2/1, 0.05 mol.L⁻¹ and 30 min, respectively. Under these conditions, high‐quality conducting fibers containing polyPy and BF (PPy‐BF) were obtained with an electrical resistivity as low as 0.54 Ω.cm. The PPy‐BF was blended with different concentrations of polyurethane (PU) by mixing the two components in a vacuum chamber and then applying compression molding. The electrical resistivity of composites with 25 wt% of PPy‐BF was around 1.8 × 10⁵ Ωcm, which is approximately 10⁸ times lower than that found for pure PU. Moreover, PU/PPy‐BF composites exhibited higher mechanical properties than pure PU and PU/PPy, indicating that these conducting fibers can also be used as reinforcement for polymer matrices. The properties of the PPy‐BF obtained by the method described herein open interesting possibilities for novel applications of electrically conducting fibers, from smart sensors to new conducting fillers that can be incorporated into several polymer matrixes to develop conducting polymer composites with good mechanical properties.POLYM. COMPOS., 2013. © 2013 Society of Plastics Engineers     

Physico‐chemical and dielectric characterization of polypyrrole clay composite

In this study, we report on the chemical and dielectric properties of polypyrrole (PPy) clay composite. The in situ polymerization has been carried out in an aqueous solution using ammonium persulfate (APS) as oxidant. Molar ratio of Pyrrole (Py) to interlayer clay cation was fixed to 4 and that of APS to Py (R ) was varied in the range of 0.25–4.00. It was shown that both the chemical and dielectric behaviors were affected by the variation of (R ). XRD results showed an intercalated structure of PPy for a value of R corresponding to 0.25. Above this value, the basal distance (d ₀₀₁) was found to be around 1.3 nm, implying that PPy is essentially located at the surface of Montmorillonite (MMT). From FTIR spectroscopy, it was found that for R = 4, PPy was degraded, resulting in a decrease of the degree of polymerization and conductivity. For all samples the AC conductivity was found to be constant until 2 × 10⁵ Hz but increased steeply above this value. The highest conductivity was found to be around 3.95 10⁻³ S.cm⁻¹ for R = 1. The composite exhibited very large values of ε′ and ε ″ at a low frequency, these values decreased with the increase of frequency. Curves of imaginary electric modulus (M ″) exhibited a frequency peak due to the process of relaxation time of conductivity (τ = 6.9410⁻⁸ s) for R = 1. POLYM. COMPOS., 38:2043–2051, 2017. © 2015 Society of Plastics Engineers     

Electrically conductive composites of polyurethane derived from castor oil with polypyrrole‐coated peach palm fibers

Electrically conducting fibers were prepared through in situ oxidative polymerization of pyrrole (Py) in the presence of peach palm fibers (PPF) using iron (III) chloride hexahydrate (FeCl₃·6H₂O) as oxidant. The polypyrrole (PPy) coated PPF displayed a PPy layer on the fibers surface, which was responsible for an electrical conductivity of (2.2 ± 0.3) × 10⁻¹ S cm⁻¹, similar to the neat PPy. Electrically conductive composites were prepared by dispersing various amounts of PPy‐coated PPF in a polyurethane matrix derived from castor oil. The polyurethane/PPy‐coated PPF composites (PU/PPF–PPy) exhibited an electrical conductivity higher than PU/PPy blends with similar filler content. This behavior is attributed to the higher aspect ratio of PPF–PPy when compared with PPy particles, inducing a denser conductive network formation in the PU matrix. Electromagnetic interference shielding effectiveness (EMI SE) value in the X‐band (8.2–12.4 GHz) found for PU/PPF–PPy composites containing 25 wt% of PPF–PPy were in the range −12 dB, which corresponds to 93.2% of attenuation, indicating that these composites are promising candidates for EMI shielding applications. POLYM. COMPOS., 38:2146–2155, 2017. © 2015 Society of Plastics Engineers     

Characterization of polypyrrole/azocalix[4]arene salts: Electrical properties and thermal stability

Polypyrrole (PPy) was doped with the azocalix[4]arene [(5,11,17,23‐tetrakis[(p‐carboxyphenyl)azo]25,26,27,28‐tetrahydroxycalix[4]arene)] host species. PPy/azocalix[4]arene salts were characterized by FTIR, TGA, SEM, X‐ray diffraction, and conductivity measurements. The properties of PPy were investigated in the presence of azocalix[4]arene host species. The conductivity of PPy increased in the presence of azocalix[4]arene. TGA results indicated that the PPy/azocalix[4]arene salts have higher thermal stability than PPy. It was observed from SEM analysis that the particle diameter of PPy decreased with increasing content of azocalix[4]arene. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation and mechanical properties of poly(vinyl chloride)/bamboo flour composites with a novel block copolymer as a coupling agent

To improve the interfacial adhesion between poly(vinyl chloride) (PVC) and bamboo flour in PVC/bamboo flour composites, a novel coupling agent, poly(styrene‐co‐maleic anhydride)‐block‐poly(styrene‐co‐acrylonitrile) {P[(SMA)‐b‐(SAN)]}, was synthesized through living free‐radical polymerization in a one‐pot reaction. P[(SMA)‐b‐(SAN)] was synthesized by a nitroxide‐mediated polymerization technique in the presence of 2,2,6,6‐tetramethylpiperidin‐l‐oxyl with azobisisobutyronitrile. The conversion of maleic anhydride (>99%) and styrene (>65%) was relatively high and yielded P[(SMA)‐b‐(SAN)] with a narrow molecular weight distribution (weight‐average molecular weight/number‐average molecular weight <1.38). PVC was blended with bamboo flours in the presence of the synthesized coupling agent with a two‐roll mill. P[(SMA)‐b‐(SAN)] was added to the PVC matrix at a concentration of 55 or 20 wt %. As the content of P[(SMA)‐b‐(SAN)] in the wood–polymer composite increased, improved morphological and mechanical behaviors were observed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation and characterization of acrylonitrile‐ethyl methacrylate copolymers and the effect of LiClO4 salt on electrical properties of copolymer films

Copolymers of poly(acrylonitrile‐co‐ethyl methacrylate), P(AN‐EMA), with three different EMA content and parent homopolymers were synthesized by emulsion polymerization. The chemical composition of copolymers were identified by FTIR, ¹H‐NMR and ¹³C‐NMR spectroscopy. The thermal properties of copolymers were modified by changing the EMA content in copolymer compositions. Various amounts of LiClO₄ salt loaded (PAN‐co‐PEMA) copolymer films were prepared by solution casting. The dielectric properties of these films at different temperatures and frequencies were investigated. It was found that the dielectric constant and ac‐conductivity of copolymer films were strongly influenced by the salt amounts and EMA content in copolymers. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Influences of co‐monomers and electrolyte acidity on morphological structure of copper‐in‐copolymer gradient film

In this paper, the influences of composition of copolymers and acidity of electrolyte in an electrochemical reactor on morphological structure of copper‐in‐polymer gradient composite film were investigated. For binary copolymers, poly(acrylonitrile‐co‐methyl acrylate) [P(AN‐co‐MA)] and poly(acrylonitrile‐co‐sodium allyl sulfonate) [P(AN‐co‐SAS)], the charged group ? SO in P(AN‐co‐SAS) improves the swelling of the copolymer phase and copper reduction to form gradient morphology; the carboxylic ester group in P(AN‐co‐MA) is not effective because of its poor hydrophilicity, but it is a cooperating component with P(AN‐co‐SAS) to avoid excess of counterion (i.e., Na⁺) in SCF, which might severely interrupt Cu²⁺ coexistence. The swelling of the polymer phase is helpful to decrease the energy of the transfer ions in SCF and to enhance copper deposition and gradient formation. The increase of surface energy because of cluster growth raises the surface energy level of deposited Cu⁰ clusters. The conteraction between these two energy factors allows the size of clusters to be 50–100 nm. The appropriate H⁺ concentration improves active Cu²⁺ reduction and thus deposited gradient copper phase in the copolymer matrix. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 373–380, 2004     

The effect of ionic liquid fragment on the performance of polymer electrolytes

An ionic liquid 1‐methyl‐3‐[2‐(methacryloyloxy)ethyl]imidazolium bis(trifluoromethane sulfonylimide) (MMEIm‐TFSI) was synthesized and polymerized. Composite polymer electrolytes based on polymeric MMEIm‐TFSI (PMMEIm‐TFSI) and poly[(methyl methacrylate)‐co‐(vinyl acetate)] (P(MMA‐VAc)) were prepared, with lithium bis(trifluoromethane sulfonylimide) (LiTFSI) as target ions (Li⁺). DSC/TGA analysis showed good flexibility and thermal stability of the composite electrolyte membranes. The AC impedance showed that the ionic conductivity of the electrolytes increased with PMMEIm‐TFSI up to a maximum value of 1.78 × 10^?4 S cm^?1 when the composition was 25 wt% P(MMA‐VAc)/75 wt% PMMEIm‐TFSI/30 wt% LiTFSI at 30 °C. The composite electrolyte membrane (transmittance ≥ 90%) can also be used as the ion‐conductive layer material for electrochromic devices, and revealed excellent colorization performance. Copyright © 2011 Society of Chemical Industry     

Multilayer composite surfaces prepared by an electrostatic self‐assembly technique with quaternary ammonium salt and poly(acrylic acid) on poly(acrylonitrile‐co‐acrylic acid) membranes

An electrostatic self‐assembly technique was applied to prepare ion complex polymer layers on polyacrylonitrile with acrylic acid segments {poly(acrylonitrile‐co‐acrylic acid) [P(AN‐co‐AA)]}. For the ionic complex layers, quaternary ammonium salts, such as cetyl trimethyl ammonium chloride (CTAC) and tetramethyl ammonium chloride (TMAC), were used as cationic species, and also, poly(acrylic acid) (PAA) was used as an anionic species. These cationic and anionic species were self‐assembled alternately on the surface of the P(AN‐co‐AA) membrane. Fourier transform infrared spectroscopy, AFM, and water contact angle measurements of the membrane surface were used to confirm the formation of the multilayer composites on the P(AN‐co‐AA). The permeabilities of water and macromolecules of different molecular weights were evaluated by a membrane filtration technique. The values of permeability strongly depended on the formation layer by layer of these ion composites on the base P(AN‐co‐AA). Through the measurement of the values of the contact angle of water, it was clear that surface nature of the base membrane treated by CTAC or TMAC and PAA dramatically changed. We concluded that such an electrostatic self‐assembly technique is useful for the preparation of multicomposite layers to modify the surface of base P(AN‐co‐AA) membranes. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Melt processable conducting poly(aniline‐co‐o‐anisidine)/linear low‐density polyethylene composites with ethylene‐acrylic acid copolymer as compatibilizer

Conducting composites of aniline/o‐anisidine copolymer doped by dodecylbenzenesulfonic acid (P(An‐co‐oAs)‐DBSA), linear low‐density polyethylene (LLDPE), and ethylene–acrylic acid copolymer (EAA) as compatibilizer were prepared by melt processing. The effects of composition on electrical conductivity, resistivity‐temperature characteristic, and mechanical properties were also investigated. The electrical conductivity of ternary composites markedly increased due to compatibilizition and protonation effect of the EAA. The SEM micrograph shows that the compatibility between the P(An‐co‐oAs)‐DBSA and the LLDPE matrix is enhanced after the introduction of EAA. The positive temperature coefficient of resistivity characteristic is observed. Tensile strength of P(An‐co‐oAs)‐DBSA/LLDPE/EAA composites is improved, compared with P(An‐co‐oAs)‐DBSA/LLDPE composites. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1511–1516, 2005     

Preparation of bi‐continuous poly(acrylonitrile‐co‐methyl acrylate) microporous membranes by a thermally induced phase separation method

Poly(acrylonitrile‐co‐methyl acrylate) [P(AN‐MA)] flat microfiltration membranes were successfully prepared via the thermally induced phase separation (TIPS) method, by using low polar caprolactam (CPL) and methoxypolyethylene glycol 550 (MPEG 550) as the mixed diluent. In this work, P(AN‐MA) membranes exhibit bi‐continuous networks, porous surfaces, high porosity, and big pore size, when membrane fabricated from a high MPEG 550 content, low P(AN‐MA) concentration, and small cooling rate, it can be dry state preservation and do not need to be impregnated by any solvent. When the ternary system was composed of 15 wt % P(AN‐MA), 12.5 wt % CPL, and 87.5 wt % MPEG 550, formed at 25 °C air bath, membrane has the highest water flux of 4420 L m^?2 h^?1. The obtained P(AN‐AN) membrane displays a high carbonic black ink rejection ranging from 83.7 to 98.5 wt %. Moreover, P(AN‐MA) polymer not only retains the advantages of PAN but also reduces the polar component from 16.2 to 10.77 MPa^0.5. It can be used membrane matrix to obtain pore structure and excellent mechanical property membrane via TIPS. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46173.