Orange to black electrochromic behaviour in poly(2-(2-thienyl)-1H-pyrrole) thin films

We have studied an electrochromic precursor, 2-(2-thienyl)-1H-pyrrole (1), using two improved procedures of the Trofimov reaction. Optimised stereochemical calculations at the B3LYP/6-311G* level showed almost equal s-cis and s-trans conformational populations in 1 with marked out-of-plane deviations of ca. 30°. Model calculations suggest that the predominant rotational conformation in undoped poly(1) would be s-trans with the essential out-of-plane deviations around the all three interheterocyclic bonds of ca. 25-30°. Monomer 1 exhibited two irreversible oxidation processes at +0.86 and +1.3 V corresponding to the oxidation of the pyrrole and thiophene rings, respectively. Orange to black electrochromic behaviour was found in ClO₄⁻ doped poly(1) thin films with colouring and bleaching times of 1.8 and 1.3 s, respectively. The colouration efficiency during the bleaching process was 233 cm²/C. The optical contrast at 450 nm was 19% and in the near-IR was 36%. The band-gap of poly(1) (1.6-1.7 eV) was found to be significantly lower than that of polypyrrole (2.85 eV) and polythiophene (2.3 eV) as a consequence of increased electron delocalisation in the system. Important differences in the morphology of doped and dedoped poly(1) films were observed by atomic-force microscopy (AFM). Doped poly(1) films showed a granular morphology with primary particles of 45-60 nm in size and an average surface roughness of 3.5 nm. On the other hand, dedoped poly(1) films showed interconnected aggregates of 65-90 nm in size as a consequence of particle fusion, with a surface roughness of 9.2 nm. In summary, poly(1) is a promising material for emerging flexible electrochromic devices such as displays and variable optical attenuators.     

Synthesis of conjugated polymers with broad absorption bands and photovoltaic properties as bulk heterojuction solar cells

Two new broad absorbing alternating copolymers, poly[1-(2,6-diisopropylphenyl)-2,5-bis(2-thienyl)pyrrole-alt-4,7-bis(3-octyl-2-thienyl)benzothiadiazole] (PTPTTBT-P1) and poly[1-(p-octylphenyl)-2,5-bis(2-thienyl)pyrrole-alt-4,7-bis(3-octyl-2-thienyl)benzothiadiazole] (PTPTTBT-P2), were prepared via Suzuki polycondensation with high yields. The two polymers were found to show characteristic absorption in the visible region of the solar spectrum. Interestingly the absorption of PTPTTBT-P1 was found to cover the visible region from 350 to 650 nm with the broad and flat absorption maximum from 440 to 510 nm in film and the absorption of PTPTTBT-P2 was found to cover the visible region from 350 to 950 nm with the relatively distinct absorption maxima at 425 and 522 nm and very weak absorption maximum at 832 nm in film. The electrochemical band gaps of the polymers were calculated to be 1.88 eV and 1.87 eV, respectively, while the optical band gaps of the polymers were calculated to be 1.94 eV and 1.87 eV, respectively. The photovoltaic properties of polymers were investigated with bulk heterojunction (BHJ) solar cells fabricated in ITO/PEDOT:PSS/polymer:PC₇₀BM(1:5 wt%)/TiOx/Al configurations. The maximum power conversion efficiency (PCE) of the solar cell composed of PTPTTBT-P1:PC₇₀BM as an active layer was 1.57% with current density (J_sc) of 8.17 mA/cm², open circuit voltage (V_oc) of 0.52 V and fill factor (FF) of 36%.     

Synthesis and photovoltaic properties of donor–acceptor polymers incorporating a structurally-novel pyrrole-based imide-functionalized electron acceptor moiety

A structurally-novel pyrrole-based imide-functionalized electron accepting monomer unit, 4,6-dibromo-2,5-dioctylpyrrolo[3,4-c]pyrrole-1,3(2H,5H)-dione (DPPD), was prepared. The new DPPD unit was copolymerized with pyrrole-based electron rich monomers, such as thiophene-(N-alkyl)pyrrole-thiophene (TPT) and fused thiophene-(N-alkyl)pyrrole-thiophene (DTP) derivatives, to afford two new polymers, namely P(TPT-DPPD) and P(DTP-DPPD), respectively. The two polymers showed a strong absorption band at 300–600 nm and 300–650 nm, respectively, and their calculated optical band gaps were 2.09 eV and 1.89 eV, respectively. The electrochemical analysis reveals that the highest occupied molecular orbital (HOMO) energy levels of P(TPT-DPPD) and P(DTP-DPPD) were positioned at −5.55 eV and −5.24 eV, respectively, whereas their lowest unoccupied molecular orbital (LUMO) energy levels were positioned at −3.46 eV and −3.35 eV, respectively. The preliminary photovoltaic properties of the polymers, P(TPT-DPPD) and P(DTP-DPPD), were examined by fabricating polymer solar cells (PSCs) with each polymer as an electron donor and PC₇₁BM as an electron acceptor. The PSCs fabricated with the configuration of ITO/PEDOT:PSS/P(TPT-DPPD) or P(DTP-DPPD):PC₇₁BM/LiF/Al showed maximum power conversion efficiency (PCE) of 0.73% and 1.64%, respectively.     

Synthesis and properties of various poly(diphenylacetylenes) containing tert-amine moieties

The polymerization of diphenylacetylene derivatives possessing tert-amine moieties, such as triphenylamine, N-substituted carbazole and indole, was examined in the presence of TaCl₅-n-Bu₄Sn (1:2) catalyst. A polymer with high molecular weight (M_w = 570 × 10³) was obtained in good yield by the polymerization of diphenylamine-containing monomer 1b, whereas the isopropylphenylamine derivative (1c) gave a polymer with relatively low molecular weight (M_w = 2.4 × 10³). The polymerization of monomer 1d containing cyclohexylphenylamine group did not proceed; however, carbazolyl- and indolyl-containing monomers also produced polymers. Poly(1b), poly(2f) and poly(4b) could be fabricated into free-standing membranes by casting toluene solutions of these polymers. The gas permeability of poly(1b) was too low to be evaluated accurately whereas poly(4b) possessing two chlorine atoms in the repeating unit showed higher gas permeability than that of poly(1b); furthermore, poly(2f) having trimethylsilyl and 3-methylindolyl groups exhibited relatively high gas permeability (). In the cyclic voltammograms of diphenylamino group-containing polymers, poly(1b) and poly(2b), the intensities of oxidation and reduction peaks decreased more than those of carbazolyl-containing poly(2a). The molar absorptivity (?) of poly(1b) at ∼700 nm increased with increasing applied voltage in the UV-vis spectrum.     

Synthesis and optoelectronic properties of thermally cross-linkable hole-transporting poly(fluorene-co-triphenylamine)

This paper describes the synthesis of a new thermally cross-linkable hole-transporting poly(fluorene-co-triphenylamine) (PFTV) by Suzuki coupling reaction and its application in polymer light-emitting diodes (PLEDs). The characteristics of PFTV were analyzed by ¹H NMR, differential scanning calorimetry, optical spectroscopy, cyclic voltammetry, and atomic force microscopy. Its HOMO level lies between those of PEDOT:PSS and poly(9,9-dioctylfluorene), forming a stepwise energy ladder to facilitate hole-injection. Multilayer device with thermally cross-linked PFTV as hole-transporting layer (ITO/PEDOT:PSS/HTL/PFO/LiF/Ca/Al) was readily fabricated by successive spin-coating processes, its maximum luminance efficiency (2.27 cd/A) was significantly higher than that without PFTV layer (0.50 cd/A). In addition, the PFTV was successfully applied as host for red-emitting Ir(piq)₂acac to obtain a device with moderate performance (5300 cd/m² and 2.64 cd/A). The PFTV is a promising hole-transporting material for the fabrication of multilayer PLEDs by wet processes as well as a potential host for phosphorescent PLEDs.     

Preparation and properties of polytolan membranes bearing p-hydroxyl groups

The polymerization of a novel monomer p-(t-butyldimethylsiloxy)tolan (1) with TaCl₅-n-Bu₄Sn provided a high molecular weight polymer (poly(1)), whose M_w reached 4.0×10⁶. The poly(1) membrane was prepared by the casting method, and converted into poly[(p-hydroxy)tolan] (poly(2)) with a mixture of trifluoroacetic acid/water. Whereas poly(1) dissolved in low polarity solvents such as toluene and chloroform, poly(2) was practically insoluble in any solvents, although it partly dissolved in methanol and ethanol. The onset weight loss temperatures of poly(1) and poly(2) in air were 320 and 360 °C, respectively, indicating fair thermal stability among substituted polyacetylenes. The oxygen permeability coefficients (P_O2) of poly(1) was 150 barrers, which is relatively small among polytolan derivatives, while that of poly(2) was 8.0 barrers and smaller owing to the presence of polar hydroxyl groups.     

Thieno[3,2-b]thiophene as π-bridge at different acceptor systems for electrochromic applications

Benzoselenadiazole, quinoxaline and thieno[3,2-b]thiophene are the units preferred in conducting polymers due to their electrochemical properties. There are no reports in the literature on polymers containing both moieties. In this study, novel benzoselenadiazole, quinoxaline and thieno[3,2-b]thiophene based monomers; 4-(3a,6a-dihydrothieno[3,2-b]thiophen-2-yl)-7-(thieno[3,2-b]thiophenyl)benzo[c][1,2,5]selenadiazole (BSeTT) and 2,3-bis(3,4-bis(decyloxy)phenyl)-5,8-dibromo-2,3-dihydroquinoxaline (QTT) were synthesized via Stille Coupling and polymerized electrochemically. These polymers were characterized in terms of their spectroelectrochemical and electrochemical properties by cyclic voltammetry and UV–Vis–NIR spectroscopy. Spectroelectrochemistry analysis of PBSeTT revealed an electronic transition at 525 nm corresponding to π–π* transition with a band gap of 0.93 eV whereas PQTT revealed electronic transitions at 440 and 600 nm corresponding to π–π* transitions with a band gap of 1.30 eV. Electrochromic investigations showed that PBSeTT has gray color PQTT switching between green and gray. Switching time of the polymers was evaluated by a kinetic study upon measuring the percent transmittance (%T) at the maximum contrast point.     

Synthesis of a pyridine substituted polycarbodiimide and its use as a solid support for chemical reagents

Optically active, polycarbodiimides 3(a, b & c) with pyridine pendant groups were synthesized using [(R) - 2,2′- binaphthoxy] (di-isopropoxy) titanium(IV) catalyst. The polymers were characterized by ¹H and ¹³C NMR, and IR. Thermal stability of these polymers (up to 162 °C by TGA), allows thermally demanding chemical transformations on their side chains without decomposition. Advantages include fine-tunability of the other pendant group of the carbodiimide monomer. This allows one to optimize the properties of the polymer without undergoing copolymerization or further post-polymerization modifications. Borane (BH₃) was coordinated to poly 3 (a & b) to prepare the functional polymers 4 (a & b) respectively. A strong IR signature peak at 2368 cm⁻¹ supports BH₃ coordination. Gravimetric analysis indicates 97-99% borane complexation of the pyridine units. In addition, the thermal stability increased to 194 °C in poly 4a is consistent with the incorporation of BH₃ to the pendant pyridine of the helical polycarbodiimide 3a. Poly 4 (a & b) can be used as supported reagents and successfully reduced the carbonyl compounds (5 a-e) in moderate to excellent yields (60-100%) and are shown to be efficient, non-volatile, stable, and mild supported-reducing reagents. Upon completion of the reduction reaction, the polymer support was quantitatively recycled as required for a green solid catalyst support.     

Tyrosine-based poly(m-phenyleneethynylene-p-phenyleneethynylene)s. Helix folding and responsiveness to a base

The Sonogashira-Hagihara polymerization of 3′,5′-diiodo-N-α-tert-butoxycarbonyl-l-tyrosine methyl ester (1) and 3′,5′-diiodo-N-α-tert-butoxycarbonyl-O-methyl-l-tyrosine methyl ester (2) with para-diethynylbenzene (3) was carried out to obtain optically active poly(m-phenyleneethynylene-p-phenyleneethynylene)s [poly(1) and poly(2)] with M_n’s ranging from 9900 to 15,000 in 80-87% yields. Poly(1) exhibited intense CD signals in DMSO and THF, but did not in CH₂Cl₂, indicating that it took a predominantly one-handed helical conformation in the former two solvents. On the other hand, there was no evidence for poly(2) to take a helical structure in these solvents. Poly(1) turned the CD sign at 390 nm from plus to minus in DMSO/H₂O = 9/1 (v/v) by the addition of NaOH. Alkaline hydrolysis of ester moieties of poly(1) and poly(2) gave the corresponding polymers having carboxy groups [poly(1a) and poly(2a)]. Poly(1a) and poly(2a) increased the CD intensity by the addition of NaOH.     

A new low-voltage-driven polymeric electrochromic

Design, synthesis, and properties of a novel donor-acceptor-donor type low-voltage-driven green polymeric electrochrome, P1, which is based on 8-(2,3-dihydrothieno[3,4-b][1,4]dioxin-5-yl)-11-(2,3-dihydrothieno[3,4-b][1,4]dioxin-7-yl)acenaphtho[1,2-b]quinoxaline (1) are highlighted. It is noted that P1 has an ambipolar (n- and p-doping processes) character in 0.1 M tetrabutylammonium hexafluorophosphate/dichloromethane solution and switches to a transmissive blue state upon oxidation. Furthermore, this new polymeric electrochromic candidate exhibits high redox stability, high coloration efficiency and/or contrast ratio, high percent transmittance (%T) and low response time (1.0 s) with a band gap of 1.10 eV-1.25 eV.     

Synthesis and characterization of donor-acceptor type 4,4′-bis(2,1,3-benzothiadiazole)-based copolymers

A series of novel donor-acceptor type polymers based on 4,4′-bis(2,1,3-benzothiadiazole) were synthesized and characterized. Two soluble regioregular tail-to-tail and head-to-head coupled polymers, poly[7,7′-bis(3-octyl-2-thienyl)-4,4′-bis(2,1,3-benzothiadiazole)] poly[3TBB3T], and poly[7,7′-bis(4-octyl-2-thienyl)-4,4′-bis(2,1,3-benzothiadiazole)] poly[4TBB4T] were synthesized by FeCl₃-mediated oxidative polymerization. To further decrease the band gap of the polymers, vinylene spacers were incorporated into the polymer backbone by Stille coupling of the corresponding monomers and (E)-1,2-bis(tributylstannyl)ethene. A crystal structure of a monomer analog shows near planar arrangement of the aromatic units in the solid state. The optical properties of the monomers and polymers were investigated by steady-state absorption and photoluminescence spectroscopy. Cyclic voltammetry measurements indicate that the polymers could be employed as acceptor materials in polymer-polymer bulk heterojunction solar cells due to their low LUMO energy of about −4.0 eV. A maximum photovoltaic power conversion efficiency of about 0.3% was observed for a 1:1 blend of regioregular poly(3-hexylthiophene) (rr-P3HT) and poly[4TBB4T] and the origin of the moderate efficiency is discussed by interpreting the device current-voltage characteristics, external quantum efficiency and incident light intensity dependence of the power conversion efficiency.     

Synthesis, electroluminescence, and photovoltaic properties of dendronized poly(p-phenylene vinylene) derivatives

Two dendronized poly(p-phenylene vinylene) (PPV) derivatives, ED-PPV and BB-PPV, have been successfully synthesized according to the Gilch route. The obtained polymers possess excellent solubility in common solvents, good thermal stability with 5% weight loss temperature of more than 340 °C. The weight-average molecular weight (M_w) and polydispersity index (PDI) of ED-PPV and BB-PPV are in the range of (1.26-2.34)×10⁵ and 1.37-1.45, respectively. Polymer light-emitting diodes (PLEDs) with the configuration of ITO/PEDOT:PSS/polymer/Ca/Al devices were fabricated, and the PLEDs emitted green-yellow light. The turn-on voltages of the PLEDs based on ED-PPV and BB-PPV were approximately 4.3, and 4.5 V, respectively. The PLED devices of ED-PPV exhibited the maximum luminance of about 157 cd/m² at 10.5 V. Photovoltaic cells with the configuration of ITO/PEDOT:PSS/polymer:C₆₀ (1:1)/Al were also fabricated, and the energy conversion efficiency of the devices based on ED-PPV and BB-PPV was measured to be 0.58, and 0.014%, respectively, under the white light at 75 mW/cm².     

Cationic phenyl-substituted poly(p-phenylenevinylene) related copolymers with efficient photoluminescence and synthetically tunable emissive colors

A series of amino-functionalized phenyl-substituted poly(p-phenylenevinylene) (PPV) related copolymers were synthesized by Wittig reaction. Their corresponding cationic conjugated polymers were successfully obtained via a post-polymerization approach. On the basis of FT-IR and ¹H NMR spectra, it was found that phenyl-substituted PPV related copolymers containing alkoxylated benzene (neutral polymer P1 and quaternized polymer P1′), phenylated benzene (neutral polymer P2 and quaternized polymer P2′) and fluorene (neutral polymer P3 and quaternized polymer P3′) moieties are of 55, 80, and 45% cis-vinylic linkage respectively while the polymer containing thiophene moiety (neutral polymer P4 and quaternized polymer P4′) is primarily of trans-vinylic linkage. Their photoluminescence (PL) were conveniently tuned from blue color to yellow color by introducing units with different optoelectronic properties into the PPV backbones. The polymer with fluorene unit and bulky phenylene-substituted benzene unit in the backbone exhibited the highest PL efficiency among these neutral and quaternized PPVs. P4′ containing little cis-vinylic linkage showed complete quenching while P1′-P3′ containing much more cis-vinylic linkage showed incomplete quenching, indicating that the quenching behavior of these cationic PPVs may be highly influenced by the content of cis-vinylic linkage in the PPV backbones.     

Synthesis and characterisation of poly(distyrylbenzene-block-hexa(ethylene oxide)) and its fluorinated analogue—two new block copolymers and their application in electroluminescent devices

Two new soluble block copolymers are reported in which chromophores and hexa(ethylene oxide) units alternate along the polymer backbone. In polymer 1 the chromophore was the distyrylbenzene unit. The polymer was synthesised via the Wittig reaction and the ionisation potential of 5.4±0.2 eV was measured by cyclic voltammetry and photoelectron spectroscopy. Polymer 1 showed a high solid-state photoluminescence efficiency (34%) and was used to make efficient (0.5 cd/A) light emitting diodes (LEDs). Polymer 1 was also used in light emitting cells; these showed luminescence in reverse bias and a reduced turn-on voltage compared to the LEDs. Polymer 2, in which the chromophore was dodecafluoro-distryrylbenzene, was prepared via the Horner-Wittig reaction and showed an ionisation potential of 6.25±0.15 eV and a solid-state photoluminescence efficiency of 17%. It was used as electron-conducting layer in a LED but failed to give significant electroluminescence. The optical energy gap for both polymers was 3.0 eV.     

Synthesis and charge carrier mobility of a solution-processable conjugated copolymer based on cyclopenta[c]thiophene

A new polymer comprising alternate thiophene and didodecyloxymethyl substituted cyclopenta[c]thiophene unit, PDCPTT, was synthesized by the Stille coupling reaction and characterized by ¹H NMR, GPC, TGA, DSC, XRD, UV-vis absorption spectroscopy, photoluminescence spectroscopy and cyclic voltammetry. The copolymer is readily soluble in tetrahydrofuran, chloroform and toluene at ambient conditions and exhibits good thermal stability as it does not exhibit noteworthy weight loss until ∼300 °C under nitrogen. This polymer possesses a broad absorption band ranging at 400-650 nm (with an optical band gap of 1.90 eV). The DFT calculation predicts the polymer to be planar and the calculated band gap is only 0.17 eV higher than the experimentally determined band gap. Didodecyloxymethyl-3,4-cyclopentane substitution on alternate thiophene in a polythiophene, hitherto unexplored, showed an effective polymer based field effect transport characteristics; exhibiting hole mobility ≈1.4 × 10⁻² cm² V⁻¹ s⁻¹.     

High-performance poly(2,3-diphenyl-1,4-phenylene vinylene)-based polymer light-emitting diodes by blade coating method

A new series of super high brightness and luminance efficient poly(2,3-diphenyl-1,4-phenylene vinylene) (DP-PPV)-based electroluminescent (EL) polymers containing methoxy or long branched alkoxy chains were synthesized via Gilch polymerization. The branched alkoxy groups were introduced to enhance solubility for blade and spin-coating processes. Monomers of DMeO-PPV and m-Ph-PPV were used to increase steric hindrance and prevent close packing of the main chain. By controlling the feeding ratio of different monomers during polymerization, DP-PPV derivatives with high molecular weight were obtained. All synthesized polymers possess high glass transition temperatures and thermal stabilities. The maximum photoluminescent emissions of the thin films are located between 544 and 547 nm. Cyclic voltammetry analysis reveals that the band gaps of these light-emitting materials are in the range of 2.75-2.84 eV. Blade coating was used to fabricate multilayer polymer light-emitting diodes. A multilayer electroluminescent device with the configuration of ITO/PEDOT:PSS/TFB/P1/TPBi/LiF/Al exhibited a very high luminescence efficiency (10.96 cd A⁻¹). The maximum brightness of the multilayer EL device ITO/PEDOT:PSS/TFB/P3/CsF/Al reached up to 78,050 cd m⁻² with a low turn-on voltage (4.0 V). For further investigation, polymer P3 was blended with DPPFBNA to achieve white light-emitting device; the multilayer devices generated a maximum brightness of 1085 cd m⁻² and a luminance efficiency of 0.75 cd A⁻¹, with CIE coordinates (0.28, 0.33) at 11 V.     

Synthesis of laterally attached side-chain liquid crystalline poly(p-phenylene vinylene) and polyfluorene derivatives for the application of polarized electroluminescence

Two series of poly(p-phenylene vinylene) and polyfluorene derivatives (PPV1-PPV4 and PF1-PF5) containing laterally attached penta(p-phenylene) mesogenes were synthesized and characterized. These polymers show nematic liquid crystalline behavior. The optical properties of the polymers were investigated by UV-vis absorption and photoluminescence spectrometers and these polymers were fabricated to form the polarized electroluminescent devices using poly(ethylenedioxythiophene)-poly(styrene sulfonic acid) (PEDOT-PSS) as an alignment layer. In the series of poly(p-phenylene vinylene) derivatives, polymer PPV4 offered the best EL device performance. It emitted yellow light at 588 nm at 4 V. The maximum brightness was about 1337 cd/m² at 9 V with a polarized ratio of 2.6. In another series of polyfluorene derivatives, PF4 offered the best EL device performance with the polarized ratio of 12.4 and a maximum luminescence of 1855 cd/m². In the case of polarized white light, as a consequence of blending small amount of PF4 and PF5 with a host polymer PF2, polarized ratio of up to 10.2 and a maximum brightness of 2454 cd/m² have been attained. The aligned films exhibited pronounced polarized ratio, implying that the polymers exhibit potential for linearly polarized LED application.     

Synthesis and gas permeability of ester substituted poly(p-phenylene)s

Polymerizations of various ester substituted 2,5-dichlorobenzoates [substituent: linear alkyl groups (1a-f), branched alkyl groups (1g-l), cyclohexyl groups (1m-o), phenyl groups (1p-r), and oxyethylene units (1s-v)] were investigated with Ni-catalyzed/Zn-mediated system in 1-methyl-2-pyrrolidone (NMP) at 80 °C. Most of monomers bearing linear and branched alkyl groups successfully polymerized to give relatively high-molecular-weight polymers (M_n = 10,000-20,800). However, the molecular weight of the polymer having eicocyl groups was low because of steric hindrance of long alkyl chain. The polymerizations of cyclohexyl 2,5-dichlorobenzoate and phenyl 2,5-dichlorobenzoate produced low-molecular-weight polymers, while the polymerizations of monomers with alkyl cyclohexyl and alkyl phenyl groups proceeded to afford polymers with relatively high-molecular-weights. The polymers possessing oxyethylene units were obtained, but the molecular weights were low when the oxyethylene chains were long. The gas permeability of membranes of poly(p-phenylene)s with alkyl chains increased as increasing the length of alkyl chain. The membranes of poly(p-phenylene)s with phenyl groups and oxyethylene units exhibited high densities and relatively low gas permeability. However, the CO₂/N₂ separation factor of membrane of poly(p-phenylene) having oxyethylene units was as large as 73.6.     

Polymeric molecular shuttles: Polypseudorotaxanes & polyrotaxanes based on viologen (paraquat) urethane backbones & bis(p-phenylene)-34-crown-10

Reaction of di(p-isocyanatophenyl)methane (MDI, 4) with N,N′-di(2-hydroxyethyl)- (1b) or N,N′-di[2-(2′-hydroxyethoxy)ethyl]-4,4′-bipyridinium di(hexafluorophosphate) (1e) and other diols [oligo(ethylene glycol)s and poly(tetramethylene oxide)s] in the presence of bis(p-phenylene)-34-crown-10 (2) afforded polyurethane (pseudo)rotaxanes as statistical (7P or 7R) and segmented analogs 10P (P = pseudorotaxane, R = rotaxane). In 7R a bulky alcohol was incorporated at the chain ends and in 13R a bulky diol as in-chain units to form polyrotaxanes and preclude the possibility of dethreading. The crown ether 2 in 10P and 13R was shown by ¹H NMR spectroscopy to be shuttling between the viologen (paraquat) and urethane sites; in DMSO the crown ether prefers the urethane site, probably because of H-bonding with the N–H moieties and complexation of the pyridinium site by the dipolar solvent, while in acetone at low temperatures the viologen site is preferred by the crown ether, with ΔH = −6.91 kcal/mol and ΔS = −22.9 eu for 13R.     

Synthesis and characterizations of conjugated copolymers containing benzo[f]isoindole-1,3-dione and diketopyrrolopyrrole units

A weak electron acceptor, 4,9-bis(5-bromothiophen-2-yl)-2-(2-ethylhexyl)-benzo[f]isoindole-1,3-dione (BIDO) was designed and synthesized. Polymer P1 derived from BIDO and 9,9-dioctylfluorene-2,7-diboronic acid bis(1,3-propanediol) ester by Suzuki cross-coupling reaction has a band gap of 2.41 eV. To expand the absorption range, a different amount of BIDO was copolymerized with a diketopyrrolopyrrole monomer to produce a series of copolymers P_a–c. The optical properties, electrochemical behavior, and energy levels of these four copolymers were investigated. The photovoltaic properties copolymers P_a–c were studied. A photovoltaic device containing P_c and [70]PCBM with a ratio of 1:2 had a power conversion efficiency of 1.17%.