Facile synthesis of Ti3SiC2 powder by high energy ball-milling and vacuum pressureless heat-treating process from Ti–TiC–SiC–Al powder mixtures

In this article, Ti/TiC/SiC/Al powder mixtures with molar ratios of 4:1:2:0.2 were high energy ball-milled, compacted, and heated in vacuum with various schedules, in order to reveal the effects of temperature, soaking time, thickness of the compacts, and carbon content on the purity of the sintered compacts. X-ray diffraction and scanning electron microscopy were employed to investigate the phase purity, particle size and morphology of the synthesized samples. It was found that the Ti₃SiC₂ content nearly reached 100 wt.% on the surface layer of the sintered compacts prepared in the temperature range from 1350 °C to 1400 °C for 1 h. Powder containing 91 wt.% Ti₃SiC₂ was successfully synthesized by heating 6 mm green compacts of 4Ti/1TiC/2SiC/0.2Al at 1380 °C for 1 h in vacuum. The excessive carbon content failed to improve the purity of Ti₃SiC₂ powder. TiC phase was the main impurity in the formation process of Ti₃SiC₂.     

Effect of excess silicon content on the formation of nano-layered Ti3SiC2 ceramic via infiltration of TiC preforms

The aim of this work was to investigate the effect of silicon content on the formation and morphology of Ti₃SiC₂ based composite via infiltration of porous TiC preforms. The gelcasting process was used for fabrication of preforms. It was found that the infiltrated sample at 1500 °C for 90 min from a mixture of 3TiC/1.5Si containing 92 wt.% Ti₃SiC₂. With the increasing of TiC and SiC impurity phases, Vickers hardness was increased to the maximum value of 12.9 GPa in Ti₃SiC₂–39 wt.%TiC composite. Microscopic observations showed that the Ti₃SiC₂ matrix was composed of columnar, platelike and equiaxial grains with respect to silicon content.     

Effects of Xe+ irradiation on Ti3SiC2 at RT and 500 °C

In this study, effects of a 400 keV Xe⁺ irradiation on Ti₃SiC₂ were systematically investigated by transmission electron microscopy (TEM). At RT, results show that the Xe⁺ irradiation induced the dissociation of Ti₃SiC₂ to polycrystalline TiC first, and then the polycrystalline to TiC nanograins with the increasing fluence. However, there is no significant microstructure change observed on the sample irradiated at 500 °C. It is demonstrated that Ti₃SiC₂ had not been completely amorpherized even up to 116.9 displacements per atom (dpa).     

Dependence of the microstructure and properties of TiC/Ti3SiC2 composites on extra C addition

TiC/Ti₃SiC₂ composites were synthesized with Ti/Si/C and Al (in which extra C addition ranges from 0 to 25 wt.%) as starting powders by hot-pressed sintering method at 1400 °C under 30 MPa. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were used to evaluate the phase composition and the fracture surface. The results reveal that with the increase of extra C addition, the content of Ti₃SiC₂ phase decreases while the content of TiC phase increases. Graphite phase is detected in the samples with extra C addition of 20 wt.% and 25 wt.%. The bending strength decreases from 554.81 MPa to 57.44 MPa due to the decrease of the densification and Ti₃SiC₂ phase content. The electrical conductivity falls from 42,474.52 s/cm to 1524.95 s/cm, resulting from lower Ti₃SiC₂ phase content and higher contact resistance.     

Fabrication of Ti3SiC2 and Ti4SiC3 MAX phase ceramics through reduction of TiO2 with SiC

Ti₃SiC₂ and Ti₄SiC₃ MAX phase ceramics were fabricated through high-temperature vacuum reduction of TiO₂ using SiC as a reductant, followed by hot pressing of the products under 25 MPa of pressure at 1600 °C. It was found that both Ti₃SiC₂ and Ti₄SiC₃ may be obtained in good yields, depending on the annealing time during the reduction step. In addition to MAX phases, the products contained some amounts of TiC. The hot pressing step did not significantly affect the composition of the products, indicating good stability of Ti₃SiC₂ and Ti₄SiC₃ under these conditions. Analysis of the densification behavior of the samples revealed lower ductility in Ti₄SiC₃ compared to Ti₃SiC₂. The samples prepared herein exhibited the flexural strength, fracture toughness and microhardness typical of coarse-grained MAX-phase ceramics.     

Phase reactions in a hot pressed TiC/Si powder mixture

This work investigated the possibility of producing dense Ti₃SiC₂ by hot pressing TiC/Si powders. A hot press with graphite heating elements was used for densification and the phase reactions of some hot pressed samples were further evaluated by pressureless heating in a dilatometer. The density and phase composition of the heat treated samples were evaluated using Archimedes principle and by X-ray diffractometry, respectively. Hot pressing resulted in a low Ti₃SiC₂ yield; the main phases were TiC and TiSi₂ regardless of starting powder composition, temperature, holding time or pressure. A second heating without pressure resulted in Ti₃SiC₂ formation, but only in samples initially hot pressed at 1300 °C or lower. At higher hot pressing temperatures, thin oxide layers on particle surfaces were locked into the structure. Acting as diffusion barriers, they prevented the Ti₃SiC₂ forming reaction. In hot pressed samples the density was significantly higher than in samples sintered without pressure.     

Machinability of Ti3SiC2 with layered structure synthesized by hot pressing mixture of TiCx and Si powder

Nanolaminate Ti₃SiC₂ was synthesized from a mixture of TiC_x (x = 0.67)/Si powder by hot pressing to increase machinability. Ti₃SiC₂ was synthesized at temperatures of 1360 °C and 1420 °C for 90 min under a pressure of 25 MPa. The X-ray diffraction results showed that while mainly Ti₃SiC₂ with some unreacted TiC_x were detected in the synthesized samples at 1360 °C, no phases except Ti₃SiC₂ phases remained in the synthesized samples at 1420 °C. The cutting resistance of Ti₃SiC₂ was measured in terms of the principle, feed, and thrust forces and was compared with that of middle-carbon steel, SM45C. The values of the principal force of the synthesized Ti₃SiC₂ were lower than those of SM45C. After machining, the roughness of the Ti₃SiC₂ was lower than those of SM45C; however, the damage to the tool bit used for the machining of SM45C was less than the damage to those used for the machining of the Ti₃SiC₂.     

In-situ fabrication of TiC-Fe3Al cermet

Titanium carbide has high hardness, resistance to oxidation and abrasion while iron aluminide has proper ductility as well as good strength and excellent oxidation resistance up to high temperatures. Therefore, it can be expected TiC-iron aluminide cermet to have excellent mechanical properties as a cutting tool and a wear-resistance material. In this study, mechanical milling and hot press sintering processes were used to manufacture in-situ TiC-Fe₃Al cermet, whose microstructure and mechanical properties were examined according to the changes in volume fraction of TiC and milling time. After 48 h of milling each mechanically alloyed powder crystallized in a TiC and Fe₃Al biphasic material. The milled powder was hot-pressed at 1250 ℃ and 50 MPa for 30 min to obtain sintered bodies also consisting of only TiC and Fe₃Al phases. The hard phase, TiC, had a size of 100–300 nm with overall uniform distribution decreasing as the volume fraction of TiC increased. The hardness of each sintered body showed a linearly increasing tendency according to the increase in TiC content, the hardness for 90 vol% TiC cermet being as high as 1813Hv. On the other hand, the bending strength was 1800 MPa and 1780 MPa when TiC volume fraction was 50% and 70%, respectively, while it showed an abrupt decrease up to 580 MPa at 90% TiC volume fraction. Fe₃Al phase is effective to toughening of TiC-Fe₃Al cermet and the volume fraction of Fe₃Al phase significantly influences the bending strength of the cermet.     

Synthesis of nanocrystalline cerium oxide by high energy ball milling

We have synthesized pure nanocrystalline CeO₂ powders of nearly spherical shape using high-energy attritor ball mill. Milling parameters such as the milling speed of 400 rpm, ball to powder ratio (40:1), milling time (30 h) and water cooled media were determined to be suitable for synthesizing nanosize (～10 nm) powders of CeO₂. The powders after milling for various durations (up-to 50 h) were characterized by X-ray Diffraction, Scanning Electron Microscopy, Energy-dispersive X-ray Spectrometry and Transmission Electron Microscopy. An average particle size of 10 nm was obtained at 30 h milling, after which the particle agglomeration started, and a mixture of nanocrystalline and amorphous phase was observed after 50 h milling.     

Mechanochemically assisted preparation of NbB2 powder

A powder mixture of Nb-B (1:2) was milled using milling media of different sizes in a planetary ball mill, and NbB₂ was mechanochemically prepared. When the mixture was milled with 5 mm diameter balls, NbB₂ started to form in 20 h and the single phase NbB₂ was obtained in 50 h. The time required for the NbB₂ formation and the single phase decreased with the increase in the ball size. The lattice parameters of the NbB₂ obtained were a = 0.3112 nm, c = 0.3276 nm. The average particle size of the NbB₂ powder obtained by milling with the 5 and 9 mm diameter balls for 50 h was approximately 370 nm.     

Effect of milling time and pH on the dispersibility of lead zirconate titanate in aqueous media for inkjet printing

Micrometre-sized Pb(Zr_0.53Ti_0.47)O₃ (PZT) powder was dispersed in water, stabilized with the ammonium polyacrylate (PAANH₄) and milled to reduce the particle size. The influence of the pH, the amount of PAANH₄, and the milling time on the zeta potential, the PZT particle size and the particle size distribution was studied. The agglomeration took place regardless the milling time at pH 3. The suspension, containing 5 vol.% of PZT and 5 wt.% of PAANH₄, milled at pH 10 for 240 min, was stable and contained particles with a narrow, log-normal particle size distribution with the median size of 160 nm. The dissociated carboxyl groups from the PAANH₄ interacted with the PZT particles as evidenced by Fourier transform infrared spectroscopy and electrosterically stabilized the particles in water at pH 10. The PZT particle size and the stability of the suspension fitted the requirements for the ink, suitable for ink-jet printing.     

High temperature interfacial phase stability of a Mo/Ti3SiC2 laminated composite

A Mo/Ti₃SiC₂ laminated composite is prepared by spark plasma sintering at 1300 °C under a pressure of 50 MPa. Al powder is used as sintering aid to assist the formation of Ti₃SiC₂. The fabricated composites were annealed at 800, 1000 and 1150 °C under vacuum for 5, 10, 20 and 40 h to study the composite's interfacial phase stability at high temperature. Three interfacial layers, namely Mo₂C layer, AlMoSi layer and Ti₅Si₃ solid solution layer are formed during sintering. Experimental results show that the Mo/Ti₃SiC₂ layered composite prepared in this study has good interfacial phase stability up to at least 1000 °C and the growth of the interfacial layer does not show strong dependence on annealing time. However, after being exposed to 1150 °C for 10 h, cracks formed at the interface.     

Influence of mechanical alloying on Ti3SiC2 formation via spark plasma sintering technique from Ti/SiC/C powders

Ti₃SiC₂ was elaborated by two different methods: (i) Spark plasma sintering of 5Ti/2SiC/C powders and (ii) mechanical alloying of powders followed by Spark plasma sintering. The results showed that mechanical alloying was not advantageous for pure Ti₃SiC₂ formation but it can significantly improve the density of the obtained bulk material via the particles refinement as well as the microhardness by increasing the TiC content. It was found that the relative density was increased up to 98.58% for the sintered mechanically alloyed sample whereas it was not more than 96.04% for the sintered 5Ti/2SiC/C starting powders. The Vickers microhardness measured for both bulk samples demonstrates a high improvement for the previously mechanically alloyed powder mixture, as it was of about 1282 Hv and only 581.2 Hv for the alloy obtained from 5Ti/2SiC/C starting powders.     

Pore accessibility of Ti3SiC2-derived carbons

We investigate the accessibility of Ti₃SiC₂-derived carbons (Ti₃SiC₂-DCs) synthesized non-isothermally using a temperature ramp. The microstructure of the Ti₃SiC₂-DCs is characterized using TEM, XRD, Raman spectroscopy and gas adsorption. For the characterization by gas adsorption, we adopt our Finite Wall Thickness (FWT) model to invert Ar adsorption isotherms at 87 K to obtain pore size and pore wall thickness distributions of the Ti₃SiC₂-DCs. Accordingly, we identify a pore accessibility problem in the Ti₃SiC₂-DCs, as reported for Ti₃SiC₂-DCs prepared at 1073 K in our previous work. A striking feature is that Ti₃SiC₂-DC prepared at the slowest ramping rate (2 K/min) has a very narrow pore size distribution, while the Ti₃SiC₂-DCs synthesized at higher ramping rates (5 and 15 K/min) have much broader pore size distributions centered around 5.2 Å. A significant amount of previously unreported ultra-microporosity is observed based on low pressure CO₂ adsorption at 273 K. Our results indicate that slow ramping rate could potentially be utilized for fine control of the ultra-microporosity of carbide-derived carbons. Finally, we have found that fast ramping rate above 5 K/min leads to subtle changes in microstructure, with long and periodic graphitic multilayers having some large pores formed in between.     

Fabrication of Ti3SiC2-based composites via three-dimensional printing: Influence of processing on the final properties

In this work the influence of the processing routes on the microstructure and properties of Ti₃SiC₂-based composites was investigated. The three main processing steps are (i) three-dimensional printing of Ti₃SiC₂ powder blended with dextrin, (ii) pressing of printed samples (uniaxial or cold isostatic pressing), and (iii) sintering of pressed samples at 1600 °C for 2 h. The Ti₃SiC₂-based composites were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS). Young's Modulus and flexural strength were measured to examine the mechanical properties. Porosity, density, shrinkage, and mass change were measured at each processing step. Those samples uniaxially pressed at 726 MPa presented the highest density, shrinkage, and mass change. However, microstructural morphologies were crack-free and homogeneous for cold isostatic pressed Ti₃SiC₂-based composites as compared to uniaxially pressed samples. The highest values for Young's Modulus (~300 GPa) and flexural strength (~3 GPa) were observed with uniaxially pressed Ti₃SiC₂-based composites.     

The production of β-SiAlON ceramics with low amounts of additive,at low sintering temperature

In the present work nano-sized powder of β-SiAlON was produced using a wet milling process. Different milling times and mediums (methyl ethyl keton, ethanol and toluene as solvents, polyethyleneglicol, oleic acid, sodium tripolyphosphate and polyvinylpyrrolidon as dispersants) were performed for the determination of the most efficient milling system. The powders were produced using a conventional process (the ball to powder ratio was 1:1.5, at 300 rpm, for 1.5 h) having a few hundred nanometer particle size, and these were used as standard powders in this study. The nano-sized β-SiAlON starting powders (<100 nm) were sintered at lower temperatures than that of the conventional powders. The amount of Y₂O₃ in powders (～130 nm), produced by high energy milling process, was fewer than conventional powders (5 wt.%). The results of the powder size, sintering behavior and mechanical properties of this sample were compared to those of the standard powder and its sintered sample. This sample, produced using the nano-powder, was investigated, and densified at 150 °C lower than that of the standard sample. Even though the amount of Y₂O₃ was decreased, the hardness of the samples was better than that of the standard sample.     

The influence of reactive milling on the structure and magnetic properties of nanocrystalline MnFe2O4

Nanocrystalline manganese ferrites (MnFe₂O₄) have been synthesized by direct milling of metallic manganese (Mn) and iron (Fe) powders in distilled water (H₂O). In order to overcome the limitation of wet milling, dry milling procedure has also been utilized to reduce crystallite size. The effects of milling time on the formation and crystallite size of wet milled MnFe₂O₄ nanoparticles have been investigated. It has been observed that single phase 18.4 nm nanocrystalline MnFe₂O₄ is obtained after 24 h milling at 400 rpm. Further milling caused deformation of the structure as well as increased crystallite size. With the aim of reducing the crystallite size of 18.4 nm, MnFe₂O₄ sample dry milling has been implemented for 2 and 4 h at 300 rpm. As a result, the crystallite size has been reduced to 12.4 and 8.7 nm, respectively. Effects of the crystalline sizes on magnetic properties were also investigated. Magnetization results clearly demonstrated that crystallite size has much more effect on the magnetic properties than average particle size.     

Reaction synthesis of layered ternary Ti2AlC ceramic

Reactive sintering of 8Ti:Al₄C₃:C powder mixtures to form the ternary carbide Ti₂AlC is studied in the temperature range 570–1400 °C. After sintering at 1400 °C for 1 h, only the MAX phase Ti₂AlC and some TiC are produced. A series of intermediate phases, such as TiC, Ti₃Al, Ti₃AlC are detected during the reactive sintering process. From X-ray diffraction (XRD) and scanning electron microscopy (SEM) characterizations, a reaction path is proposed for the intermediate phases and Ti₂AlC formation. Results show that reaction kinetics may play an important role in the understanding of the reaction mechanisms.     

Improved mechanical properties of Al2O3 ceramic by in-suit generated Ti3SiC2 and TiC via hot pressing sintering

Al₂O₃ multi-phase composites with different volume fractions of SiC varying from 0 vol% to 30.0 vol% were fabricated by vacuum hot pressing sintering at 1600 °C under the pressure of 30 MPa for 2.0 h. The aim of this work was to investigate the effect of SiC content on the morphology and mechanical properties of the Al₂O₃ multi-phase composite. The results show that the addition of SiC and Ti can produce new strengthening and reinforcing phases include Ti₃SiC₂, TiC, Ti₅Si₃, which would hamper the migration of grain boundaries and promote sintering. The mechanical performances could reach the comprehensive optimal values for 20.0 vol% SiC, delamination and transgranular fracture being the major crack propagation energy dissipation mechanisms.     

Microstructure and properties of Al2O3–TiC nanocomposites fabricated by spark plasma sintering from high-energy ball milled reactants

In situ synthesis of Al₂O₃–TiC nanocomposite powders from a mixture of titanium, graphite, and Al₂O₃ powders by high-energy ball milling (HEBM) and its consolidation through spark plasma sintering (SPS) were investigated. After being milled for 25 h at ambient temperature, the powder mixtures were mainly composed of homogeneous nanosized Al₂O₃ particle and amorphous TiC solid solution. The relative density of the samples consolidated by SPS technique in vacuum at 1480 °C for 4 min reached 99.2%. The final products exhibited very fine microstructure, and the grain sizes of Al₂O₃ and TiC were about 400 nm and 200 nm, respectively, with a flexure strength of 944 ± 21 MPa, Vickers hardness 21.0 ± 0.3 GPa, fracture toughness 3.87 ± 0.2 MPa m^1/2, and electrical conductivity 1.2787 × 10⁵ S m⁻¹.