Preparation and properties of bisphenol A‐based sulfonated poly(arylene ether sulfone) proton exchange membranes for direct methanol fuel cell

Novel bisphenol A‐based sulfonated poly(arylene ether sulfone) (bi A‐SPAES) copolymers were successfully synthesized via direct copolymerization of disodium 3,3′‐disulfonate‐4,4′‐dichlorodiphenylsulfone, 4,4′‐dichlorodiphenylsulfone, and bisphenol A. The copolymer structure was confirmed by Fourier transform infrared spectra and ¹H NMR analysis. The series of sulfonated copolymers based membranes were prepared and evaluated for proton exchange membranes (PEM). The membranes showed good thermal stability and mechanical property. Transmission electron microscopy was used to obtain the microstructures of the synthesized polymers. The membranes exhibit increased water uptake from 8% to 66%, ion exchange capacities from 0.41 to 2.18 meq/g and proton conductivities (25°C) from 0.012 to 0.102 S/cm with the degree of sulfonation increasing. The proton conductivities of bi A‐SPAES‐6 membrane (0.10–0.15 S/cm) with high‐sulfonated degree are higher than that of Nafion 117 membrane (0.095–0.117 S/cm) at all temperatures (20–100°C). Especially, the methanol diffusion coefficients of membranes (1.7 × 10^?8 cm²/s–8.5 × 10^?7 cm²/s) are much lower than that of Nafion 117 membrane (2.1 × 10^?6 cm²/s). The new synthesized copolymer was therefore proposed as a candidate of material for PEM in direct methanol fuel cell. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Proton Conducting Membranes Based on Poly(2,2′‐imidazole‐5,5′‐bibenzimidazole)

Poly(2,2′‐imidazole‐5,5′‐bibenzimidazole) (PBI‐imi) was synthesized via the polycondensation between 3,3′,4,4′‐tetraaminobiphenyl and 4,5‐imidazole‐dicarboxylic acid. Effects of the reaction conditions on the intrinsic viscosity of the synthesized polymers were studied. The results show that the molecular weight of the polymers increases with increasing monomer concentration and reaction time, and then levels off. With higher reaction temperature, the molecular weight of the polymer is higher. With the additional imidazole group in the backbone, PBI‐imi shows improved phosphoric acid doping ability, as well as a little higher proton conductivity when compared with widely used poly[2,2′‐(m‐phenylene)‐5,5′‐bibenzimidazole] (PBI‐ph).Whereas, PBI‐imi and PBI‐ph have the similar chemical oxidation stability. PBI‐imi/3.0 H₃PO₄ composite membranes exhibit a proton conductivity as high as 10^–4 S cm^–1 at 150 °C under anhydrous condition. The temperature dependence of proton conductivity of acid doped PBI‐imi can be modeled by an Arrhenius equation.     

Proton‐conducting blend membranes of crosslinked poly(vinyl alcohol)–sulfosuccinic acid ester and poly(1‐vinyl‐1,2,4‐triazole) for high temperature fuel cells

New type of composite membranes were synthesized by crosslinking of poly(vinyl alcohol) (PVA) with sulfosuccinic acid (SSA) and intercalating poly(1‐vinyl‐1,2,4‐triazole) (PVTri) into the resulting matrix. The complexed structure of the membranes was confirmed by Fourier transform infrared (FTIR) spectroscopy. The resulting hybrid membranes were transparent, flexible, and showed good thermal stability up to ～200°C. The proton conductivities of the membranes were investigated as a function of PVTri and SSA and operating temperature. The water/methanol uptake was measured and the results showed that solvent absorption of the materials increased with increasing PVTri content in the matrix. The proton conductivity of the membranes continuously increased with increasing SO₃H content, PVTri content, and the temperature. In the anhydrous state, the maximum proton conductivity is 7.7 × 10^?5 S/cm for PVA–SSA–PVTri‐1 and for PVA–SSA–PVTri‐3 is 1.6 × 10^?5 S/cm at 150°C. After humidification (RH = 100%), PVA–SSA–PVTri‐4 showed a maximum proton conductivity of 0.0028 S/cm at 60°C. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Synthesis and Characterization of a New Fluorine‐Containing Polybenzimidazole (PBI) for Proton‐Conducting Membranes in Fuel Cells

A new type of fluorine‐containing polybenzimidazole, namely poly(2,2′‐(2,2′‐bis(trifluoromethyl)‐4,4′‐biphenylene)‐5,5′‐bibenzimidazole) (BTBP‐PBI), was developed as a candidate for proton‐conducting membranes in fuel cells. Polymerization conditions were experimentally investigated to achieve high molecular weight polymers with an inherent viscosity (IV) up to 1.60 dl g^–1. The introduction of the highly twisted 2,2′‐disubstituted biphenyl moiety into the polymer backbone suppressed the polymer chain packing efficiency and improved polymer solubility in certain polar organic solvents. The polymer also exhibited excellent thermal and oxidative stability. Phosphoric acid (PA)‐doped BTBP‐PBI membranes were prepared by the conventional acid imbibing procedure and their corresponding properties such as mechanical properties and proton conductivity were carefully studied. The maximum membrane proton conductivity was approximately 0.02 S cm^–1 at 180 °C with a PA doping level of 7.08 PA/RU. The fuel cell performance of BTBP‐PBI membranes was also evaluated in membrane electrode assemblies (MEA) in single cells at elevated temperatures. The testing results showed reliable performance at 180 °C and confirmed the material as a candidate for high‐temperature polymer electrolyte membrane fuel cell (PEMFC) applications.     

Synthesis and characterization of some new aromatic polytriazoles as proton conductive membranes

A series of new poly(1,2,4-triazole)s (PTAs) containing pyridine heterocyclic ring, bearing bulky aromatic pendent groups, were synthesized from the reaction of the corresponding polyhydrazides with aniline or 4-aminobenzenesulfonic acid in polyphosphoric acid (PPA) at 175 °C. The non-sulfonated PTAs showed glass transition temperatures (T _gs) of 220–250 °C and inherent viscosities (η _inh) equal to 0.48–0.78 dL/g, and the sulfonated poly(1,2,4-triazole)s (S-PTAs) exhibited T _gs of 235–265 °C and inherent viscosities equal to 0.50–0.83 dL/g. The former polymers were soluble in conc. H₂SO₄ and partially soluble in hot N,N-dimethylformamide (DMF), dimethyl sulfoxide (DMSO), dimethylacetamide (DMAc), and 1-methyl-2-pyrrolidone (NMP), and the latter were soluble in DMF, NMP, DMSO and DMAc at room temperature. All polymers had useful levels of thermal stability and were stable up to 450 °C in nitrogen. The proton conductivities of undoped sulfonated polytriazole membranes and the acid-doped sulfonated polytriazole membranes lie in the range of 5 × 10^?4–8.1 × 10^?3 and 5 × 10^?3–2.3 × 10^?2 S/cm, respectively, at 90 °C and 100 % relative humidity.     

Phosphonic acid functionalized siloxane crosslinked with 3‐glycidoxyproyltrimethoxysilane grafted polybenzimidazole high temperature proton exchange membranes

Phosphonic acid functionalized siloxane crosslinked with 3‐glycidoxypropyltrimethoxysilane (GPTMS) grafted polybenzimidazole (PBI) membranes are prepared by sol–gel process. The structure of the membranes is characterized by Fourier‐transform infrared spectroscopy and X‐ray diffraction spectroscopy. SEM images of the membranes show that the membranes are homogeneous and compact. The crosslinked membranes exhibit excellent thermal stability, chemical stability and mechanical property. The proton conductivity of the crosslinked membranes increases by an order of magnitude over range of 20 °C to 160 °C under anhydrous condition, which can reach 3.15 × 10^?2 S cm^?1 at 160 °C under anhydrous condition. The activation energy of proton conductivity for membranes decreases with increase of PBI, because the formation of hydrogen bond network between the phosphonic acid and the imidazole ring can enhance the continuity of hydrogen bond in the membrane. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44818.     

Sulfonated poly(arylene ether ketone)s prepared by direct copolymerization as proton exchange membranes: Synthesis and comparative investigation on transport properties

Sulfonated poly(aryl ether ketone)s (SPAEK) copolymers were synthesized by aromatic nucleophilic polycondensation from 3,3′, 5,5′‐tetramethyl‐4, 4′–biphenol, 1,4‐bis(4‐fluorobenzoyl) benzene, and disulfonated difluorobenzophenone. The SPAEK membranes did not exhibit excessive swelling in hot water and at the same time show the proton conductivities in the range of 0.030 S/cm to 0.099 S/cm at 80°C. The methanol diffusion coefficients of the SPAEK membranes were in the range of 4.7 × 10^?7 to 8.1 × 10^?7cm²/s measured at 25°C. The transport properties of this series of SPAEK copolymers were compared to poly(aryl ether ether ketone)s (SPEEK), poly(aryl ether ether ketone ketone)s (SPEEKK), and Nafion® membranes. It was found that the transport properties (including proton conductivity and methanol permeability) follows the trend of SPEEKK‐60 < SPAEK‐60 < SPEEK‐60 < Nafion® 117, the order of which is also attributed to the differences in the chemical structure of the polymers and the membrane morphology. In general, this novel series of SPAEK membranes possess various advantages, such as low cost of the initial monomers, high thermal and mechanical stability, and low methanol permeability while simultaneously possessing sufficient proton conductivity, which makes them notably promising as proton exchange membrane (PEM) materials in direct methanol fuel cell (DMFC) applications. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Electrospun poly(lithium 2‐acrylamido‐2‐methylpropanesulfonic acid) fiber‐based polymer electrolytes for lithium‐ion batteries

Novel single‐ion conducting polymer electrolytes based on electrospun poly(lithium 2‐acrylamido‐2‐methylpropanesulfonic acid) (PAMPSLi) membranes were prepared for lithium‐ion batteries. The preparation started with the synthesis of polymeric lithium salt PAMPSLi by free‐radical polymerization of 2‐acrylamido‐2‐methylpropanesulfonic acid, followed by ion‐exchange of H⁺ with Li⁺. Then, the electrospun PAMPSLi membranes were prepared by electrospinning technology, and the resultant PAMPSLi fiber‐based polymer electrolytes were fabricated by immersing the electrospun membranes into a plasticizer composed of ethylene carbonate and dimethyl carbonate. PAMPSLi exhibited high thermal stability and its decomposition did not occur until 304°C. The specific surface area of the electrospun PAMPSLi membranes was raised from 9.9 m²/g to 19.5 m²/g by varying the solvent composition of polymer solutions. The ionic conductivity of the resultant PAMPSLi fiber‐based polymer electrolytes at 20°C increased from 0.815 × 10^?5 S/cm to 2.12 × 10^?5 S/cm with the increase of the specific surface area. The polymer electrolytes exhibited good dimensional stability and electrochemical stability up to 4.4 V vs. Li⁺/Li. These results show that the PAMPSLi fiber‐based polymer electrolytes are promising materials for lithium‐ion batteries. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation and characterization of sulfonated block‐graft copolyimide/sulfonated polybenzimidazole blend membranes for fuel cell application

Polymer electrolyte blend membranes composed of sulfonated block‐graft polyimide (S‐bg‐PI) and sulfonated polybenzimidazole (sPBI) were prepared and characterized. The proton conductivity and oxygen permeability coefficient of the novel blend membrane S‐bg‐PI/sPBI (7 wt%) were 0.38 S cm^?1 at 90 °C and 98% relative humidity and 7.2 × 10^?13 cm³(STP) cm (cm² s cmHg)^?1 at 35 °C and 76 cmHg, respectively, while those of Nafion^® were 0.15 S cm^?1 and 1.1 × 10^?10 cm³(STP) cm (cm² s cmHg)^?1 under the same conditions. The apparent (proton/oxygen transport) selectivity calculated from the proton conductivity and the oxygen permeability coefficient in the S‐bg‐PI/sPBI (7 wt%) membrane was 300 times larger than that determined in the Nafion membrane. Besides, the excellent gas barrier properties based on an acid ? base interaction in the blend membranes are expected to suppress the generation of hydrogen peroxide and reactive oxygen species, which will degrade fuel cells during operation. The excellent proton conductivity and gas barrier properties of the novel membranes promise their application for future fuel cell membranes. © 2015 Society of Chemical Industry     

Pre‐Oxidized Acrylic Fiber Reinforced Ferric Sulfophenyl Phosphate‐Doped Polybenzimidazole‐Based High‐Temperature Proton Exchange Membrane

Pre‐oxidized acrylic fiber (POAF) and ferric sulfophenyl phosphate (FeSPP) are incorporated into polybenzimidazole (PBI) membrane for the first time to prepare high‐temperature proton exchange membranes (PEMs). The strong hydrogen bonds formed between PBI/POAF and FeSPP lead to good dispersion of POAF and FeSPP, facilitate the construction of proton channels, and enhance the dimensional and mechanical stability of the membranes. PBI/FeSPP (30 wt%) shows good proton conductivity (5.43 × 10⁻² and 4.13 × 10⁻² S cm⁻¹ at 180 °C at 50% and 0 relative humidity (RH), respectively) and improved dimensional and mechanical stability compared with pristine PBI. By incorporating 5 wt% POAF into PBI/FeSPP (30 wt%), the swelling ratios are halved and the mechanical strength is enhanced by almost 30% while the proton conductivity is slightly affected (3.84 × 10⁻² and 2.97 × 10⁻² S cm⁻¹ at 180 °C at 50% and 0 RH for PBI/FeSPP (30 wt%)/POAF (5 wt%), respectively). This work offers a new route in the preparation of high‐temperature PEMs with enhanced properties.

     

Synthesis and properties of sulfonated poly(arylene ether nitrile) copolymers containing carboxyl groups for proton‐exchange membrane materials

A series of sulfonated poly(arylene ether nitrile) copolymers containing carboxyl groups were synthesized via a nucleophilic aromatic substitution reaction from phenolphthalein, hydroquinone sulfonic acid potassium salt, and 2,6‐difluorobenzonitrile in N‐methyl pyrrolidone (NMP) with K₂CO₃ as a catalyst. The synthesized copolymers had good solubility in common polar organic solvents and could be easily processed into membranes from solutions of dimethyl sulfoxide, NMP, N,N′‐dimethyl acetylamide, and dimethylformamide. Typical membranes in acid form were gained, and the chemical structures of these membranes were characterized by Fourier transform infrared analysis. The thermal properties, fluorescence properties, water uptake, ion‐exchange capacity, and proton conductivities of these copolymers were also investigated. The results indicate that they had high glass‐transition temperatures in the range 151–187°C and good thermal stability, with the 10 wt% loss temperatures ranging from 330 to 351°C under nitrogen. The copolymers showed characteristic unimodal ultraviolet–visible (UV–vis) absorption and fluorescence emission, and the UV–vis absorption, fluorescence excitation, and emission peaks of the copolymers were obvious. Moreover, the copolymer membranes showed good water uptake and proton conductivities at room temperature and 55% relative humidity because of the introduction of both sulfonic acid groups and carboxyl groups into the copolymers, whose contents were in ranges 18.45–67.86 and 3.4 × 10^?4 to 3.0 × 10^?3 s/cm, respectively. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40213.     

New organic–inorganic hybrid membranes based on sulfonated polyimide/aminopropyltriethoxysilane doping with sulfonated mesoporous silica for direct methanol fuel cells

A series of novel composite methanol‐blocking polymer electrolyte membranes based on sulfonated polyimide (SPI) and aminopropyltriethoxysilane (APTES) doping with sulfonated mesoporous silica (S‐mSiO₂) were prepared by the casting procedure. The microstructure and properties of the resulting hybrid membranes were extensively characterized. The crosslinking networks of amino silica phase together with sulfonated mesoporous silica improved the thermal stability of the hybrid membranes to a certain extent in the second decomposition temperature (250–400°C). The composite membranes doping with sulfonated mesoporous silica (SPI/APTES/S‐mSiO₂) displayed superior comprehensive performance to the SPI and SPI/APTES membranes, in which the homogeneously embedded S‐mSiO₂ provided new pathways for proton conduction, rendered more tortuous pathways as well as greater resistance for methanol crossover. The hybrid membrane with 3 wt % S‐mSiO₂ into SPI/APTES‐4 (SPI/A‐4) exhibited the methanol permeability of 4.68 × 10^?6 cm² s^?1at 25°C and proton conductivity of 0.184 S cm^?1 at 80°C and 100%RH, while SPI/A‐4 membrane had the methanol permeability of 5.16 × 10^?6 cm² s^?1 at 25°C and proton conductivity of 0.172 S cm^?1 at 80°C and 100%RH and Nafion 117 exhibited the values of 8.80 × 10^?6 cm² s^?1 and 0.176 S cm^?1 in the same test conditions, respectively. The hybrid membranes were stable up to about 80°C and demonstrated a higher ratio of proton conductivity to methanol permeability than that of Nafion117. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and characterization of polybenzimidazole/α‐zirconium phosphate composites as proton exchange membrane

To improve the high‐temperature performance of proton exchange membranes, the polybenzimidazole (PBI)/α‐zirconium phosphate (α‐Zr(HPO₄)₂·nH₂O, α‐ZrP) proton exchange composite membranes were prepared in this study. PBI polymer containing a large amount of ether units has been synthesized from 3,3′‐ diaminobenzidine (DAB) and 4,4′‐oxybis (benzoic acid) by a direct polycondensation in polyphosphoric acid. The polymer exhibited a good solubility in most polar solvents. Inorganic proton conductor α‐ZrP nanoparticles have been obtained using a synthesis route involving separate nucleation and aging steps (SNAS). The effects of α‐ZrP doping content on the composite membrane performance were investigated. It was found that the introduction of ZrP improved the thermal stability of the composite membranes. The PBI/ZrP composite membranes exhibited excellent mechanical strength. The composite membrane with 10 wt% ZrP showed the highest proton conductivity of 0.192 S cm^?1 at 160°C under anhydrous condition. The proton conducting mechanism of the PBI/ZrP composite membranes was proposed to explain the proton transport phenomena. The experimental results suggested that the PBI/ZrP composite membranes may be a promising polymer electrolyte used in high temperature proton exchange membrane fuel cells (HT‐PEMFCs) under anhydrous condition. POLYM. ENG. SCI., 56:622–628, 2016. © 2016 Society of Plastics Engineers     

Sulfonated poly(ether ether ketone)/epoxy/phenol novolac blend proton‐exchange membranes with low methanol permeability

A crosslinked epoxy [4,4′‐diglycidyl‐(3,3′,5,5′‐tetramethylbiphenyl) epoxy resin (TMBP)], cured by phenol novolac (PN), was introduced into a sulfonated poly(ether ether ketone) (SPEEK) membrane (ion‐exchange capacity = 2.0 mequiv/g) with a casting‐solution, evaporation, and heating crosslinking method to improve the mechanical properties, dimensional stability, water retention, and methanol resistance. By Fourier transform infrared analysis, the interactions between the sulfonic acid groups and hydroxyl groups in the blend membranes were confirmed. The microstructure and morphology of the blend membranes were investigated with atomic force microscopy. As expected, the blend membranes showed excellent mechanical properties, good thermal properties (thermal stability above 200°C), lower swelling ratios (1.4% at 25°C and 7.0% at 80°C), higher water retention (water diffusion coefficient = 9.8 × 10^?6 cm²/s), and a lower methanol permeability coefficient (3.6 × 10^?8 cm²/s) than the pristine SPEEK membrane. Although the proton conductivity of the blend membranes decreased, a higher selectivity (ratio of the proton conductivity to the methanol permeability) was obtained than that of the pristine SPEEK membrane. The results showed that the SPEEK/TMBP/PN blend membranes could have potential use as proton‐exchange membranes in direct methanol fuel cells. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

High Molecular Weight Polybenzimidazole Membranes for High Temperature PEMFC

High temperature operation of proton exchange membrane fuel cells under ambient pressure has been achieved by using phosphoric acid doped polybenzimidazole (PBI) membranes. To optimize the membrane and fuel cells, high performance polymers were synthesized of molecular weights from 30 to 94 kDa with good solubility in organic solvents. Membranes fabricated from the polymers were systematically characterized in terms of oxidative stability, acid doping and swelling, conductivity, mechanical strength and fuel cell performance and durability. With increased molecular weights the polymer membranes showed enhanced chemical stability towards radical attacks under the Fenton test, reduced volume swelling upon the acid doping and improved mechanical strength at acid doping levels of as high as about 11 mol H₃PO₄ per molar repeat polymer unit. The PBI‐78kDa/10.8PA membrane, for example, exhibited tensile strength of 30.3 MPa at room temperature or 7.3 MPa at 130 °C and a proton conductivity of 0.14 S cm^–1 at 160 °C. Fuel cell tests with H₂ and air at 160 °C showed high open circuit voltage, power density and a low degradation rate of 1.5 μV h^–1 at a constant load of 300 mA cm^–2.     

Synthesis and characterization of acid–base polyimides bearing pendant sulfoalkoxy groups for direct methanol fuel cell applications

A series of acid–base polyimides with sulfonic acid groups in the side chains have been prepared, based on a new synthesized sulfonated diamine monomer containing pyridine functional group. The effect of the introduction of pyridine groups into copolymer backbone on the properties of membrane were evaluated through the investigation of membrane parameters. The copolymers produced flexible, tough, and transparent membranes by solvent casting method. All the prepared membranes displayed high thermal stability, great oxidative stability and good mechanical properties. They exhibited appropriate water uptake (15.8–30.2 wt % at 80°C) and remarkable dimensional stability (2.5–6.9% at 80°C). The proton conductivity of SPI‐80 was 1.01 × 10^?2 S cm^?1 at room temperature. Moreover, the methanol permeability of SPI‐80 membrane was 1.22 × 10^?7 cm² s^?1, which was lower than 23.8 × 10^?7 cm² s^?1 of Nafion 117. Therefore, these acid‐base polyimides materials have a promising prospect for direct methanol fuel cell applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42238.     

Sulfonation of poly(phthalazinone ether sulfone ketone) by heterogeneous method and its potential application on proton exchange membrane (PEM)

A series of sulfonated PPESK (SPPESKs) were synthesized through a heterogeneous sulfonation process with fuming sulfuric acid as sulfonating agent in a chloroform solvent. Membranes prepared from SPPESKs were investigated and proved to be candidates of proton exchange membrane in fuel cell operating at high temperature and low humidity. The heterogeneous sulfonation reaction is verified to first occur on the interface of the acid phase and the chloroform phase, then went on in the acid phase. SPPESKs with sulfonation degree (DS) up to 2.0 are obtained through a new reprecipitation method. Effects of reaction temperature, reaction time, acid/polymer ratio, and chloroform/polymer ratio on the sulfonation reaction are reported in details. An increase in sulfonation degree results in the increase of hydrophilicity, bringing about a substantial gain in proton conductivity. SPPESK membranes exhibit high water uptake of about 105.4% with DS of 1.01, almost two times higher than that of Nafion® with similar dimensional variation. Conductivity values at 35°C, 60% R.H. ranging from 10^?3 to 10^?2 S/cm were measured, which are comparable to or higher than that of Nafion® 112 (1.635 × 10^?2 S/cm) under the same test condition. Thermogravimetric analysis shows that SPPESK membranes are stable up to 290°C in N₂. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1002–1009, 2007     

A novel polybenzimidazole composite modified by sulfonated graphene oxide for high temperature proton exchange membrane fuel cells in anhydrous atmosphere

A novel functional graphene with high ion exchange capacity (IEC) was prepared by grafting reaction induced by ⁶⁰Co γ‐ray irradiation using graphene oxide. Then, polybenzimidazole/radiation grafting graphene oxide (PBI/RGO) composite membranes were prepared by the solution‐casting method and doped with phosphoric acid (PA) to improve their proton conductivity. The properties of PBI/GO/PA and PBI/RGO/PA membranes including the PA doping level, chemical stability, proton conductivity and mechanical properties were evaluated and compared. The tensile strength of PBI/RGO/PA membranes (ranging from 27.3 to 38.5 MPa) increases at first and then decreases with the increase of the RGO content, and is significantly higher than that of other PA doped PBI‐based membranes. The proton conductivity of PBI/RGO‐3/PA membrane is 28.0 mS cm^?1 at 170 °C without humidity, with an increase of 72.0% compared with that of PBI/PA membrane. These results suggest that PBI/RGO/PA membranes have the potential to be used as high‐temperature proton exchange membranes. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44986.     

Synthesis and characterization of homo‐ and copolymers of 3‐(2‐cyano ethoxy)methyl‐ and 3‐[methoxy(triethylenoxy)]methyl‐3′‐methyl‐oxetane

Two oxetane‐derived monomers 3‐(2‐cyanoethoxy)methyl‐ and 3‐(methoxy(triethylenoxy)) methyl‐3′‐methyloxetane were prepared from the reaction of 3‐methyl‐3′‐hydroxymethyloxetane with acrylonitrile and triethylene glycol monomethyl ether, respectively. Their homo‐ and copolyethers were synthesized with BF₃· Et₂O/1,4‐butanediol and trifluoromethane sulfonic acid as initiator through cationic ring‐opening polymerization. The structure of the polymers was characterized by FTIR and¹H NMR. The ratio of two repeating units incorporated into the copolymers is well consistent with the feed ratio. Regarding glass transition temperature (T_g), the DSC data imply that the resulting copolymers have a lower T_g than pure poly(ethylene oxide). Moreover, the TGA measurements reveal that they possess in general a high heat decomposition temperature. The ion conductivity of a sample (P‐AN 20) is 1.07 × 10^?5 S cm^?1 at room temperature and 2.79 × 10^?4 S cm^?1 at 80 °C, thus presenting the potential to meet the practical requirement of lithium ion batteries for polymer electrolytes. Copyright © 2005 Society of Chemical Industry     

Vinyl‐addition type norbornene copolymers containing flexible spacers and sulfonated pendant groups for proton exchange membranes

Novel sulfonated poly(2‐butoxymethylenenorbornene‐co‐2‐(6‐phenoxy‐hexyloxymethylene)‐5‐norbornene [sP(BN/PhHN)] were prepared successfully through vinyl‐addition type polymerization and then sulfonated with concentrated sulfuric acid (98%) as sulfonating agent in a component solvent. The sP(BN/PhHN)‐40 with the maximal degree of sulfonation of 40% can be obtained by controlling the sulfonating reaction time from 8 to 20 h, and a proton conductivity of 3.35 × 10^?3 S/cm was achieved at 70°C. The methanol permeabilities of these membranes were in the range from 0.26 to 6.58 × 10^?7 cm²/s, which were remarkably lower than Nafion (2.36 × 10^?6 cm²/s). TEM analysis revealed that these side‐chain type membranes have a microphase separated structure composed of hydrophilic side‐chain domains and hydrophobic polynorbornene main chain domains. Sulfonated polynorbornene containing soft spacers displayed better properties, such as lower water uptake, high thermal properties, mechanical properties, and low methanol permeability. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013