Homogeneous Fabrication of Al2O3–ZrO2–SiC Whisker Composite by Surface-Induced Coating

Al₂O₃–ZrO₂–SiC whisker composites were prepared by surface-induced coating of the precursor for the ZrO₂ phase on the kinetically stable colloid particles of Al₂O₃ and SiC whisker. The fabricated composites were characterized by a uniform spatial distribution of ZrO₂ and SiC whisker phases throughout the Al₂O₃ matrix. The fracture toughness values of the Al₂O₃–15 vol% ZrO₂–20 vol% SiC whisker composites (∼12 MPa.m^1/2) are substantially greater than those of comparable Al₂O₃–SiC whisker composites, indicating that both the toughening resulting from the process zone mechanism and that caused by the reinforced SiC whiskers work simultaneously in hot-pressed composites.     

Phase Diagram of the Alumina–Zirconia–Samaria System

The phase diagram of the Al₂O₃–ZrO₂–Sm₂O₃ system was constructed in the temperature range 1250°–2800°C. The phase transformations in the system are completed in eutectic reactions. No ternary compounds or regions of appreciable solid solution were found in the components or binaries in this ternary system. Two new ternary and one new binary eutectics were found. The minimum melting temperature is 1680°C and it corresponds to the ternary eutectic Al₂O₃+F-ZrO₂+SmAlO₃. The solidus surface projection, the schematic of the alloy crystallization path, and the vertical sections present the complete phase diagram of the Al₂O₃–ZrO₂–Sm₂O₃ system.     

Metastable Alumina Structures in Melt-Extracted Alumina–25 wt% Zirconia and Alumina–42 wt% Zirconia Ceramics

Microstructures are examined of rapidly solidified hypoeutectic Al₂O₃–25 wt% ZrO₂ and eutectic Al₂O₃–42 wt% ZrO₂ ceramic alloys by using transmission electron microscopy and scanning transmission electron microscopy. Structures observed in the hypoeutectic alloy were dendritic. Three different types of dendrite morphologies were observed. These are believed to be the stable α- and metastable γ- and δ- modifications of alumina. The cores of the γ-alumina dendrites were somewhat richer in ZrO₂ than those of α-alumina dendrites; δ-alumina dendrites were substantially enriched in ZrO₂. The lamellar structure of the eutectic in the Al₂O₃–42 wt% ZrO₂ alloy became increasingly finer with increasing cooling rate and at the highest cooling rates was replaced by a fully amorphous structure (except in some instances a ZrO₂-rich needlelike phase identifiable as δ-alumina was found in the amorphous matrix). An interpretation is given of the results obtained, based on assumed metastable free energy curves and dendrite growth theory.     

Sintering and Crystallization of CaO–Al2O3–ZrO2–SiO2 Glasses Containing Different Amount of Al2O3

In this work several complementary techniques have been employed to carefully characterize the sintering and crystallization behavior of CaO–Al₂O₃–ZrO₂–SiO₂ glass powder compacts after different heat treatments. The research started from a new base glass 33.69 CaO–1.00 Al₂O₃–7.68 ZrO₂–55.43SiO₂ (mol%) to which 5 and 10 mol% Al₂O₃ were added. The glasses with higher amounts of alumina sintered at higher temperatures (953°C [lower amount] vs. 987°C [higher amount]). A combination of the linear shrinkage and viscosity data allowed to easily find the viscosity values corresponding to the beginning and the end of the sintering process. Anorthite and wollastonite crystals formed in the sintered samples, especially at lower temperatures. At higher temperatures, a new crystalline phase containing ZrO₂ (2CaO·4SiO₂·ZrO₂) appeared in all studied specimens.     

Strength and Phase Stability of Yttria-Ceria-Doped Tetragonal Zirconia/Alumina Composites Sintered and Hot Isostatically Pressed in Argon–Oxygen Gas Atmosphere

Yttria-ceria-doped tetragonal zirconia (Y,Ce)-TZP)/alumina (Al₂O₃) composites were fabricated by hot isostatic pressing at 1400° to 1450°C and 196 MPa in an Ar–O₂ atmosphere using the fine powders prepared by hydrolysis of ZrOCl₂ solution. The composites consisting of 25 wt% Al₂O₃ and tetragonal zirconia with compositions 4 mol% YO_1.5–4 mol% CeO₂–ZrO₂ and 2.5 mol% YO_1.5–5.5 mol% CeO₂–ZrO₂ exhibited mean fracture strength as high as 2000 MPa and were resistant to phase transformation under saturated water vapor pressure at 180°C (1 MPa). Postsintering hot isostatic pressing of (4Y, 4Ce)-TZP/Al₂O₃ and (2.5Y, 5.5Ce)-TZP/Al₂O₃ composites was useful to enhance the phase stability under hydrothermal conditions and strength.     

Microstructures of Y2O3-Stabilized ZrO2 Electron Beam-Physical Vapor Deposition Coatings on Ni-Base Superalloys

The microstructures of ZrO₂–20 wt% Y₂O₃ thermal barrier coatings formed by electron beam-physical vapor deposition on a Nibase superalloy have been studied by transmission electron microscopy. The coating systems consist of several layers, including a superalloy substrate, a bond coat, an Al₂O₃ scale, and the PVD coating. The overall ceramic thermal barrier coatings were characterized, with special emphasis being given to the α-Al₂O₃ scale which forms between the bond coat and the ZrO₂₋Y₂O₃ coating. The oxide scale exhibited various morphologies in different coating systems; the majority of the porosity formed in this region for all coatings.     

Influence of the Y2O3 Content and Temperature on the Mechanical Properties of Melt-Grown Al2O3–ZrO2 Eutectics

The effect of Y₂O₃ content on the flexure strength of melt-grown Al₂O₃–ZrO₂ eutectics was studied in a temperature range of 25°–1427°C. The processing conditions were carefully controlled to obtain a constant microstructure independent of Y₂O₃ content. The rod microstructure was made up of alternating bands of fine and coarse dispersions of irregular ZrO₂ platelets oriented along the growth axis and embedded in the continuous Al₂O₃ matrix. The highest flexure strength at ambient temperature was found in the material with 3 mol% Y₂O₃ in relation to ZrO₂(Y₂O₃). Higher Y₂O₃ content did not substantially modify the mechanical response; however, materials with 0.5 mol% presented a significant degradation in the flexure strength because of the presence of large defects. They were nucleated at the Al₂O₃–ZrO₂ interface during the martensitic transformation of ZrO₂ on cooling and propagated into the Al₂O₃ matrix driven by the tensile residual stresses generated by the transformation. The material with 3 mol% Y₂O₃ retained 80% of the flexure strength at 1427°C, whereas the mechanical properties of the eutectic with 0.5 mol% Y₂O₃ dropped rapidly with temperature as a result of extensive microcracking.     

Major Influences on the Particle-Size–Transformation-Temperature Relation in Al2O3–ZrO2 Composites

The energetics of martensitic transformation in ZrO₂ is studied using a thermodynamic approach, with particular reference to Al₂O₃–ZrO₂ composites. The different characters of three types of transformation-toughened ceramics are analyzed, and several factors affecting the t → m transformation in Al₂O₃–ZrO₂ composites are discussed. The expression of transformation temperature dependence on particle size is derived and has good agreement with experimental results. The energetics concerned with nucleation of martensitic transformation is also discussed.     

Measurement of Residual Stresses in Oxide–ZrO2 Three-Layer Composites

Al₂O₃–ZrO₂ and MgO–ZrO₂ layered composites were fabricated in such a way that the outer layers of bar-shaped specimens consisted of the oxide (Al₂O₃ or MgO) and unstabilized ZrO₂, while the bulk consisted of the oxide and partially stabilized ZrO₂. During cool-down from the sintering or the annealing temperature, the outer layers expanded because of the tetragonal → monoclinic transition in ZrO₂, thereby creating compressive stresses in the outer layers and tensile stresses in the bulk. Residual stresses were determined using a strain gage technique in which a strain gage was mounted on one face while the opposing face was incrementally ground off. Measurement of the strain as a function of thickness permitted the evaluation of residual stresses using pertinent equations from simple beam theory.     

Mechanical Properties of Hot Isostatically Pressed Zirconia-Toughened Alumina Ceramics Prepared from Coprecipitated Powders

Amorphous Al₂O₃–ZrO₂ composite powders with 5–30 mol% ZrO₂ have been prepared by adding aqueous ammonia to the mixed solution of aqueous aluminum sulfate and zirconium alkoxide containing 2-propanol. Simultaneous crystallization of γ-Al₂O₃ and t -ZrO₂ occurs at 870°–980°C. The γ-Al₂O₃ transforms to α-Al₂O₃ at 1160°–1220°C. Hot isostatic pressing has been performed for 1 h at 1400°C under 196 MPa using α-Al₂O₃– t -ZrO₂ composite powders. Dense ZrO₂-toughened Al₂O₃ (ZTA) ceramics with homogeneous-dispersed ZrO₂ particles show excellent mechanical properties. The toughening mechanism is discussed. The microstructures and t / m ratios of ZTA are examined, with emphasis on the relation between strength and fracture toughness.     

Formation of Zirconia Solid Solutions Containing Alumina Prepared by New Preparation Method

In the system ZrO₂–Al₂O₃, a new method for preparing ZrO₂ solid solutions from ZrCl₄ and AlCl₃ using hydrazine monohydrate is investigated. c -ZrO₂ solid solutions containing up to ∼40 mol% Al₂O₃ crystallize at low temperatures from amorphous materials. The formation mechanism is discussed from IR spectral data. The values of the lattice parameter α increase linearly from 0.5072 to 0.5105 nm with increasing Al₂O₃ content. At higher temperatures, transformation of the solid solutions proceeds as follows: c ( SS ) → t ( ss ) → t ( ss ) +α-Al₂O₃→ m +α-Al₂O₃. m -ZrO₂–α-Al₂O₃ composite ceramics are fabricated by hot isostatic pressing for 2 h at 1250°C and 196 MPa. Microstructures and mechanical properties are examined, in connection with increasing Al₂O₃ content.     

Application of a Tough Surface Layer to a Fiber-Bonded Composite

The feasibility of creating "tough surface material" using oxide-fiber-reinforced oxide matrix ceramics was studied. Al₂O₃ fiber/(ZrO₂, Al₂O₃) matrix composite was used as the surface material of a Si–Ti–C–O-fiber-bonded composite. The sintering of the matrix (ZrO₂ and Al₂O₃) of the surface composite layer (SCL) and its bonding to the fiber-bonded composite (FBC) were done simultaneously by vacuum hot pressing. A spherical indentation test demonstrated the advantage of the SCL in reducing the damage of the base FBC from an indenter, because the high fracture resistance of the surface composite layer could reduce the stress concentration by the cumulative microfracture process.     

Consolidation of Alumina—Zirconia Mixtures by a Colloidal Process

The relationship between the dispersion of colloidal powder particles in Al₂O₃–ZrO₂ suspensions and the microstructures of consolidated compacts was examined. Suspensions were prepared from Al₂O₃ powder and ZrO₂ sol with average particle sizes of 390 and 62 nm, respectively. The dispersion was controlled by pH and salt concentration adjustments. The compacts composed of completely separated Al₂O₃ and ZrO₂ layers were obtained from well-dispersed suspensions with pH values below about 4 and salt concentration of 0.0527 M. An increase in pH or salt concentration resulted in macroscopically uniform compacts. The compacts made from suspensions with pH values above about 7, however, were composed of a mixture of Al₂O₃ and ZrO₂ agglomerates, with one acting as a matrix and the other a dispersed phase. Suspensions with a pH value of 4.5 and optimum salt concentrations resulted in compacts with microscopically uniform microstructure. Above or below these salt concentrations, ZrO₂ agglomerates were distributed in an Al₂O₃ matrix. The optimum concentration was dependent on solid content. In addition, the dispersion of mixed suspensions was compared with those of single-component suspensions. The ZrO₂ particles formed three-dimensional networks during agglomeration, which reduced the component separation in suspensions and during consolidation.     

Electrical Conductivity of Alumina/Aluminum Composites Synthesized by Directed Metal Oxidation

Electrical conductivities of Al₂O₃/A1 composite synthesized by directed oxidation of an aluminum alloy, and sintered Al₂O₃–4% MgO are measured. The high conductivity of the Al₂O₃/A1 composite compared to sintered Al₂O₃–4% MgO is shown as proof of the presence of continuous metal channels in the composite. Furthermore, the conductivity data are used to determine the activation energy for the diffusion of the dominant charge carrier in the oxide matrix.     

Thermal Expansions and Chemical Durabilities of Yttria–Aluminosilicate Glasses Containing Na2O and ZrO2

Properties of glasses in the system Y₂O₃–Al₂O₃–SiO₂ containing Na₂O and ZrO₂ were investigated. The difference between the thermal expansion coefficients (Δα) at temperatures above T _g and those below T _g, microhardness, density, and chemical durability were measured in relation to the Al₂O₃/Y₂O₃ molar ratio. These glasses were found to have a smaller value of Δα than that of a commercial coating glass.     

Oxidation of ZrB2–SiC: Influence of SiC Content on Solid and Liquid Oxide Phase Formation

The effect of SiC concentration on the liquid and solid oxide phases formed during oxidation of ZrB₂–SiC composites is investigated. Oxide-scale features called convection cells are formed from liquid and solid oxide reaction products upon oxidation of the ZrB₂–SiC composites. These convection cells form in the outermost borosilicate oxide film of the oxide scale formed on the ZrB₂–SiC during oxidation at high temperatures (≥1500°C). In this study, three ZrB₂–SiC composites with different amounts of SiC were tested at 1550°C for various durations of time to study the effect of the SiC concentration particularly on the formation of the convection cell features. A calculated ternary phase diagram of a ZrO₂–SiO₂–B₂O₃ (BSZ) system was used for interpretation of the results. The convection cells formed during oxidation were fewer and less uniformly distributed for composites with a higher SiC concentration. This is because the convection cells are formed from ZrO₂ precipitates from a BSZ oxide liquid that forms upon oxidation of the composite at 1550°C. Higher SiC-containing composites will have less dissolved ZrO₂ because they have less B₂O₃, which results in a smaller amount of precipitated ZrO₂ and consequently fewer convection cells.     

Homogeneous ZrO2–Al2O3 Composite Prepared by Nano-ZrO2 Particle Multilayer-Coated Al2O3 Particles

ZrO₂–Al₂O₃ nanocomposite particles were synthesized by coating nano-ZrO₂ particles on the surface of Al₂O₃ particles via the layer-by-layer (LBL) method. Polyacrylic acid (PAA) adsorption successfully modified the Al₂O₃ surface charge. Multilayer coating was successfully implemented, which was characterized by ξ potential, particle size. X-ray diffraction patterns showed that the content of ZrO₂ in the final powders could be well controlled by the LBL method. The powders coated with three layers of nano-ZrO₂ particles, which contained about 12 wt% ZrO₂, were compacted by dry press and cold isostatically pressed methods. After sintering the compact at 1450°C for 2 h under atmosphere, a sintered body with a low pore microstructure was obtained. Scanning electron microscopy micrographs of the sintered body indicated that ZrO₂ was well dispersed in the Al₂O₃ matrix.     

Reactive Coating of Zircon on Mullite and Mullite—Alumina Substrates

A stable zirconia coating of 20–30 pm thickness on a mullite substrate with a different alumina/silica ratio was obtained by reactive coating of zircon. It is shown that the Al₂O₃/ SiO₂ ratio of the mullite substrate drastically affects the morphology of the zirconia coating. The results are explained on the basis of the Al₂O₃–SiO₂–ZrO₂ phase equilibria.     

Vanadate Hot Corrosion Behavior of India, Yttria-Stabilized Zirconia

Powders of In₂O₃–Y₂O₃"dual stabilized"ZrO₂ (IYSZ) were prepared using sol-gel procedures and tested for resistance to destabilization by molten NaVO₃ at 700° and 900°C. IYSZ powders with stabilizer oxide compositions ranging from 100% down to about 50% In₂O₃ were superior to 100%-Y₂O₃-stabilized ZrO₂ (YSZ) in resistance to destabilization, especially at 700°C. Small additions of Y₂O₃ were speculated to reduce the acidity of the ZrO₂ oxide anion lattice, and, therefore, improve bonding of In₂O₃ (more acidic than Y₂O₃) into the ZrO₂ lattice.     

Al2O3–ZrO2–SiO2 Ternary Glasses for Molybdenum Oxidation Barriers

The wettability of binary and ternary glasses belonging to SiO₂–Al₂O₃–ZrO₂ diagram has been studied using the sessile drop technique at 1750° and 1800°C. The ternary SiO₂–Al₂O₃–ZrO₂ (90–5–5 wt%) glass has proved to be well appropriated as a molybdenum oxidation barrier coating. The addition of 5 wt% of MoO₂ slightly improves its wettablity at higher temperatures without affecting its oxidation barrier properties. The Mo comes into the glass network as a mixture of Mo⁵⁺, Mo⁴⁺, and Mo⁶⁺. After oxidation at 1000°C in oxygen atmosphere, the molybdenum remains in the glass network as Mo⁶⁺.