Optical and photoluminescent properties of sol-gel Al-doped ZnO thin films

Al-doped zinc oxide (AZO) thin films have been prepared via a sol-gel process. Optical and photoluminescent properties of the AZO films have been investigated. The UV absorption edge was blue shifted with increasing Al doping concentration. Efficient green–yellow emission was obtained after annealing at 850 °C. For the 850 °C-annealed samples, the green peak was red shifted from 518 to 565 nm as the Al doping concentration increased from 0 to 2.0 at.%. In addition, violet emission in the range of 400–450 nm was observed in the 850 °C-annealed AZO films. The possible origins responsible for these emission bands have been discussed.     

Co-emission of UV, violet and green photoluminescence of ZnO/TiO2 thin film

ZnO/TiO₂ thin films were fabricated on quartz glass substrates by E-beam evaporation. The structural and optical properties were investigated by X-ray diffraction (XRD), Raman spectra, optical transmittance and photoluminescence. XRD analysis indicates that the TiO₂ buffer layer can increase the preferential orientation along the (002) plane of the ZnO film. PL measurements suggest that co-emission of strong UV peak at 378 nm, violet peak at 423 nm and weak green luminescence at 544 nm is observed in the ZnO/TiO₂ thin film. The violet luminescence emission at 423 nm is attributed to the interface trap in the ZnO film grain boundaries.     

衬底温度对PLD方法生长的ZnO薄膜结构和发光特性的影响

在不同的衬底温度下, 通过脉冲激光淀积的方法在Si衬底上生长出c轴高度取向的ZnO薄膜. ZnO薄膜的结构和表面形貌通过X射线衍射和原子力显微镜表征. 同时以He-Cd激光和同步辐射作为激发源来测试样品的发光特性. 实验结果表明, 在衬底温度为500℃时生长的ZnO薄膜具有非常好的晶体质量, 并且表现出很强的紫外发射. 在用同步辐射为激发源的低温(18K)光致发光谱中, 还观察到了一个位于430nm处的紫光发射, 我们认为这个紫光发射与存在于晶粒间界的界面势阱所引起的缺陷态有关, 这个势阱可能起源于Zn填隙(Zn _i)     

Photoluminescence and photoconductivity studies of ZnO nanoparticles prepared by solid state reaction method

In the present work, the effect of annealing temperature on the luminescence and photoconductivity properties of ZnO nanoparticles (NPs) has been investigated. The ZnO NPs have been prepared at low temperature by a simple one step solid state reaction method using ZnSO₄·7H₂O as a starting precursor. X-ray diffraction results show, the prepared samples have a hexagonal wurtzite structure of ZnO NPs. FE-SEM reveals that the prepared ZnO nanoparticles have perfect spherical shape with little agglomeration. UV–visible absorption spectrum of as-prepared ZnO sample shows an absorbance peak at ~372 nm (~3.32 eV), which is blue shifted as compared to bulk ZnO (~386 nm). The annealed sample exhibits red shift of absorption peak. The photoluminescence spectra of as-prepared sample as well as annealed samples show one emission peak in UV region, and violet, blue, blue-green and green emissions in visible region. The sample annealed at 650 °C results in a significant reduction in luminescence as compared to that of the sample annealed at 450 °C. The photoconductivity properties such as voltage dependence of photocurrent, growth and decay of photocurrent as well as wavelength dependence of photocurrent have been studied in detail.     

Study of the growth of inorganic and organic electrodes onto polyethylene terephthalate substrates

Aluminum doped ZnO (AZO) 2 wt.% and un-doped ZnO thin films of different thickness were deposited by Pulsed DC Magnetron Sputtering onto Poly-Ethylene Terephthalate (PET) substrates, whereas PEDOT:PSS was spin-coated onto the AZO/PET. The optical properties of the samples were measured by in-situ Spectroscopic Ellipsometry in the Vis-fUV energy range (1.5-6.5 eV), where it was found that the ZnO energy gap decreases after a critical thickness while it remains constant for AZO thin films. Electrical characterization of ZnO films shows that the films exhibit metallic behavior independently of their thickness. Also, High Resolution Transmission Electron Microscopy revealed the growth of polycrystalline ZnO onto PET substrates. Concerning the PEDOT: PSS/AZO/PET materials, the thickness of the AZO films has been found to affects neither the fundamental energy gap nor the other absorption peaks of PEDOT: PSS.     

Effects of substrate temperatures on the thermal stability of Al-doped ZnO thin films grown by DC magnetron sputtering

In this work, Al-doped (4 at%) ZnO(AZO) thin films were prepared by DC magnetron sputtering using a home-made ceramic target at different substrate temperatures. The microstructure, optical, electrical and thermal stability properties of these thin films were characterized systematically using scanning electron microscopy, UV–Vis-NIR spectrometry, X-ray diffraction, and Hall measurements. It was observed that the AZO thin films deposited at 350 °C exhibited the lowest resistivity of 5.76 × 10⁻⁴ Ω cm, high average visible transmittance (400–800 nm) of 92%, and the best thermal stability. Comparing with the AZO thin films deposited at low substrate temperatures, the AZO thin films deposited at 350 °C had the highest compact surface morphology which could hinder the chemisorbed and diffused oxygen. This was considered to be the main mechanism which was responsible for the thermal degradation of AZO thin films.     

Room temperature deposition and properties of ZnO:Al thin films by nonreactive DC magnetron sputtering

Transparent and conductive ZnO:Al (AZO) thin films were prepared at room temperature by nonreactive DC magnetron sputtering from ceramic ZnO:Al targets. The effects of Al doping level and argon gas pressure on microstructure, growth behavior, resistivity and transmittance of AZO thin films were investigated. The experimental results show that AZO thin films change from polycrystalline to preferred c-axis-orientation just at high argon gas pressure. The resistivity of AZO films first decreases with the increase of Al content under 3 wt%, then increases when the Al content is over 3 wt%. The argon gas pressure also effect on the resistivity of AZO thin films due to the change of dispersion related the grain and crystal boundary. When the argon gas pressure from 0.6 to 3.0 Pa, the resistivity of AZO films decreases to a lowest resistivity of 1.4 × 10⁻³ Ω cm when the argon gas pressure is 1.5 Pa, then increases gently. The Al content and argon gas pressure had a little influence on transmittance, and the average optical transmittances of AZO thin films were from 86% to 90%, but the absorption edge has a blue shift with the increase of doping level and argon gas pressure.     

Optical and structural analysis of porous silicon coated with GZO films using rf magnetron sputtering

In the production of porous silicon (PS) to optoelectronic application one of the most significant constrains is the surface defects passivation. In the present work we investigate, gallium-doped zinc oxide (GZO) thin films deposited by rf magnetron sputtering at room temperature on PS obtained with different etching times. The X-ray diffraction (XRD), Fourier transform infrared (FTIR) and atomic force microscopy (AFM) analysis have been carried out to understand the effect of GZO films coating on PS. Further, the XRD analysis suggests the formation of a good crystalline quality of the GZO films on PS. From AFM investigation we observe that the surface roughness increases after GZO film coating. The photoluminescence (PL) measurements on PS and GZO films deposited PS shows three emission peaks at around 1.9 eV (red-band), 2.78 eV (blue-band) and 3.2 eV (UV-band). PL enhancement in the blue and ultraviolet (UV) region has been achieved after GZO films deposition, which might be originated from a contribution of the near-band-edge recombination from GZO.     

Synthesis and properties of close packed ZnO:Al submicro-rods deposited by pulsed laser ablation

Al-doped ZnO (AZO) semiconducting thin films consisting of perpendicularly aligned submicro-rods were deposited on silicon substrate by conventional pulsed laser ablation. No catalyst was used in this process. It was found that the rod structure can be grown at relatively high oxygen pressures (1-20 Torr) and relatively high substrate temperatures (550-700 °C). Low resistivity and high carrier concentration can be obtained in these Al-doped ZnO rods with relatively high Al concentrations. Increasing Al doping reduces the electric resistivity and increase carrier concentration. The photoluminescence property measurement indicates an increased UV emission with a small amount Al doping and reduced UV emission with further increase of Al concentration.     

Effect of Cu layer thickness on the structural, optical and electrical properties of AZO/Cu/AZO tri-layer films

Highly conducting AZO/Cu/AZO tri-layer films were successfully deposited on glass substrates by RF magnetron sputtering of Al-doped ZnO (AZO) and ion-beam sputtering of Cu at room temperature. The microstructures of the AZO/Cu/AZO multilayer films were studied using X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM) and atomic force microscope (AFM). X-Ray diffraction measurements indicate that the AZO layers in the tri-layer films are polycrystalline with the ZnO hexagonal structure and have a preferred orientation with the c-axis perpendicular to the substrates. With the increase of Cu thickness, the crystallinity of AZO and Cu layers is simultaneously improved. When the Cu thickness increases from 3 to 13 nm, the resistivity decreases initially and then varies little, and the average transmittance shows a first increase and then decreases. The maximum figure of merit achieved is 1.94 × 10⁻² Ω⁻¹ for a Cu thickness of 8 nm with a resistivity of 7.92 × 10⁻⁵ Ω cm and an average transmittance of 84%.     

Properties of ZnO:Al films deposited on polycarbonate substrate

Transparent conducting aluminum-doped zinc oxide (ZnO:Al) films have been prepared on polycarbonate (PC) substrates by pulsed laser deposition technique at low substrate temperature (room-100 °C); Nd-YAG laser with wavelength of 1064 nm was used as laser source. The experiments were performed at various oxygen pressures (3 pa, 5 pa, and 7 Pa). In order to study the influence of the process parameters on the deposited (ZnO:Al) films, X-ray diffraction and atomic force microscopy were applied to characterize the structure and surface morphology of the deposited (ZnO:Al) films. Polycrystalline ZnO:Al films having a preferred orientation with the c-axis perpendicular to the substrate were deposited with a strong single violet emission centering about 377–379 nm without any accompanying deep level emission. The average transmittances exceed 85% in the visible spectrum for 300 nm thick films deposited on polycarbonate.     

ZnO缓冲层上低温生长Al掺杂的ZnO薄膜

采用射频磁控溅射法在ZnO缓冲层上制备了不同Al掺杂量的ZnO（AZO）薄膜。利用X射线衍射（XRD）、扫描电子显微镜（SEM）和光致发光（PL）等表征技术,研究了AZO薄膜的微观结构、表面形貌和发光特性。结果表明,随着Al掺杂量的增加,ZnO薄膜的择优取向性发生了改变,且当Al的掺杂量为0.81%（原子分数）时,（002）衍射峰与其它衍射峰强度的比值达到最大,表明适合的Al掺杂使ZnO薄膜的择优取向性得到了改善。在可见光范围内薄膜的平均透过率超过70%。通过对样品光致发光（PL）谱的研究,发现所有样品出现了3个发光峰,分别对应于以444nm（2.80eV）、483nm（2.57eV）为中心的蓝光发光峰和以521nm（2.38eV）为中心较弱的绿光峰。并对样品的发光机理进行了详细的探讨。     

Electrical and optical properties of Al-doped ZnO films deposited by hollow cathode gas flow sputtering

Al-doped ZnO (AZO) films were deposited on glass by hollow cathode gas flow sputtering using Zn-Al alloy targets. Sputtering power for all the depositions was fixed at 1500 W. Resistivities of 0.81-1.1 × 10^− 3 Ω cm were obtained for AZO films deposited at room temperature with an O₂ flow from 38 to 50 standard cubic centimetre/minute (SCCM), while static deposition rates were almost constant at 270-300 nm/min. On the other hand, lower resistivities of 5.2-6.4 × 10^− 4 Ω cm were obtained for AZO films deposited at 200 °C with an O₂ flow from 25 to 50 SCCM, while the static deposition rates were almost constant at 200-220 nm/min. Average transmittances in the visible light region were above 80% for both sets of films.     

Plasmon assisted intense blue-green emission from ZnO/ZnS nanocrystallites

Excellent luminescence properties of ZnO/ZnS nanocrystallites prepared using simple wet chemical approach at room temperature have been reported. ZnS coating on the surface of ZnO nanocrystallites enhanced the green emission (around 500 nm) by a factor of 2. The intensity of the blue emission around 450 nm of ZnO/ZnS nanocrystallites is observed to be as high as three times the emission intensity of pure ZnO nanocrystallites. A further overall increase by a factor of ∼2.5 has also been observed in the intensity of wide blue-green emission when the sample was prepared onto grating compared to that of the samples prepared onto uncoated as well as gold coated quartz. The enhanced emission is thought to be due to plasmon assisted electromagnetic field enhancement near nanocrystallites-metal interface. This is supported by power dependent photoluminescence measurements. The strong enhanced blue-green emission covering a wide spectral range of ∼375-650 nm signifies potential optoelectronic applications in near UV and VIS wavelength regimes.     

Microstructure and properties of Al-doped ZnO thin films by nonreactive DC magnetron sputtering at room temperature following rapid thermal annealing

A series of Al-doped ZnO (AZO) thin films deposited by nonreactive DC magnetron sputtering at room temperature following rapid thermal annealing was studied to examine the influence of these Al doping concentration, sputtering power and annealing temperature on their microstructure, electrical and optical transport properties. AZO thin films with Al dopant of 3 wt% were oriented more preferentially along the (002) direction, bigger grain size and lower electrical resistivity The resistivity of AZO films decreases with the increase of Al content from 1 to 3 wt%, sputtering power from 60 to 100 W and the annealing temperature from 50 to 250 °C. Sputtering power and annealing had some effect on the average transmittance of AZO thin films. For AZO thin films with Al doping level of 3 wt%, the lowest electrical resistivity of 5.3 × 10⁻⁴ Ω cm and the highest optical transmittance of 88.7% could gain when the sputtering power was 100 W and the annealing temperature was 200 °C or above.     

Nonlinear optical investigations on Al doping ratio in ZnO thin film under pulsed Nd:YAG laser irradiation

In the present study, it has been reported on the effect of Al doping on linear and nonlinear optical properties of ZnO thin films synthesized by spray pyrolysis method. The structural properties of ZnO thin films with different Al doping levels (0–4 wt%) were analyzed using X-ray diffraction (XRD). The results obtained from XRD analysis indicated that the grain size decreased as the Al doping value increased. The UV–Vis diffused refraction spectroscopy was used for calculation of band gap. The optical band gap of Al-doped ZnO (AZO) thin films is increased from 3.26 to 3.31 eV with increasing the Al content from 0 to 4 wt%. The measurements of nonlinear optical properties of AZO thin films have been performed using a nanosecond Nd:YAG pulse laser at 532 nm by the Z-scan technique. The undoped ZnO thin film exhibits reverse saturation absorption (RSA) whereas the AZO thin films exhibit saturation absorption (SA) that shows RSA to SA process with adding Al to ZnO structure under laser irradiation. On the other hand, all the films showed a self-defocusing phenomenon because the photons of laser stay on below the absorption edge of the ZnO and AZO films. The third-order nonlinear optical susceptibility, χ⁽³⁾, of AZO thin films, was varied from of the order of 10^?5–10^?4 esu. The results suggest that AZO thin films may be promising candidates for nonlinear optical applications.     

Low-temperature growth of highly c-oriented InN films on glass substrates with ECR-PEMOCVD

High quality InN films are deposited with an interlayer of high c-orientation (002) AZO (Aluminium-doped Zinc Oxide; ZnO:Al) films on glass substrates by electron cyclotron resonance plasma-enhanced metal organic chemical vapor deposition (ECR-PEMOCVD) at low temperature. AZO films used as a buffer layer are effective for the epitaxial growth of InN films. The influence of Trimethyl Indium (TMIn) flux on the properties of InN films is systematically investigated by reflection high energy electron diffraction (RHEED), X-ray diffraction analysis (XRD), atomic force microscopy (AFM) and optical transmittance spectra. The results indicate that high quality InN films with high c-orientation and small surface roughness are successfully achieved at an optimized Trimethyl Indium (TMIn) flux of 5.5 sccm. The InN/AZO structures have great potential for the development of full spectra solar cells.     

Effects of Al content on the properties of ZnO:Al films prepared by Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and ZnO co-sputtering

Aluminum doped zinc oxide (AZO) films were deposited on quartz substrates by radio-frequency magnetron co-sputtering method with ZnO and Al₂O₃ ceramic targets. The structural, optical and electrical properties of these films as a function of the Al content were investigated. XRD results reveal that the AZO films are wurtzite structure with (002) preferred orientation. The average transmittance of all the films is higher than 80% in a wide wavelength range from 400 to 1,500 nm. The band gap energy, calculated from their optical absorption spectra, is in the range of 3.50–3.66 eV depending on the Al content. Doping of Al³⁺ in the ZnO makes the film surface roughness decrease. The dopant Al³⁺ acts as electron donor by which the electrical conductivity and carrier concentration of the films are obviously increased until the Al³⁺ reaches its saturation content of about 4.50 at.%.     

Thickness dependence of structural, electrical and optical properties of sprayed ZnO:Cu films

ZnO:Cu thin films have been deposited by spray pyrolysis techniques within two different (450 °C and 500 °C) substrate temperatures. The structural properties of ZnO:Cu thin films have been investigated by X-ray diffraction techniques. The X-ray diffraction spectra showed that ZnO:Cu thin films are polycrystalline with the hexagonal structure and show a good c-axis orientation perpendicular to the substrate. The most preferential orientation is along the (002) direction for all spray deposited ZnO:Cu films together with orientations in the (100) and (101) planes also being abundant. Some parameters of the films were calculated and correlated with the film thickness for two different substrate temperatures. The optical properties of ZnO:Cu thin films have been investigated by UV/VIS spectrometer and the band gap values were found to be ranging from 3.29 eV to 3.46 eV.     

The low temperature synthesis of Al doped ZnO films on glass and polymer using pulsed co-magnetron sputtering: H2 effect

It has been reported that a small amount of hydrogen in argon plasma induces an increase in the crystallite size of the as-deposited films. In addition, control of the hydrogen partial pressure is expected to improve the carrier mobility by increasing the crystallinity of the film (larger crystal size and lower grain boundary effects). Al doped ZnO (AZO) films were deposited by co-CFUBM (closed field unbalanced magnetron) sputtering. The ultimate aim was to deposit transparent films on a polymer substrate with a low electrical resistivity. Therefore, the structural, optical and electrical properties of AZO films were investigated as a function of the hydrogen partial pressure. A minimum resistivity and maximum transparency of 8 × 10^− 4 Ω cm and 88.1% were obtained, respectively. A critical P_H2 was expected to improve the carrier mobility by increasing the crystallinity of the film. However, above this value, conductivity reduced due to the formations of oxides such as ZnO and Al₂O₃ in the AZO films.