Synthesis of CdS nanoparticles dispersed within amphiphilic poly(urethane acrylate‐co‐styrene) films

CdS nanoparticles were prepared using amphiphilic urethane acrylate nonionomer (UAN) precursor chains having a poly(propylene oxide)‐based hydrophobic segment and a hydrophilic poly(ethylene oxide) segment. Cadmium salts were first dissolved in UAN/styrene solutions, and then the solutions were copolymerized to obtain poly(urethane acrylate‐co‐styrene) films containing dissolved cadmium salts. After reduction with H₂S gas, freestanding films containing CdS nanoparticles were obtained. Transmission electron microscopy images of the films showed that 9.67‐nm CdS nanoparticles were dispersed within the poly(urethane acrylate‐co‐styrene) matrix. The formation of CdS nanoparticles was also confirmed with UV absorption spectra and photoluminescence emission spectra of the films. Transmission electron microscopy and dynamic mechanical analysis measurements confirmed that hydrophilic/hydrophobic microphase separation in UAN/styrene solutions occurred during the dissociation of the cadmium salts, and the microphase‐separated structures were locked in by crosslinking copolymerization. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 2357–2363, 2005     

Morphology and properties of poly(benzoxazine‐co‐urethane)s based on bisphenol‐S/aniline benzoxazine

Poly(benzoxazine‐co‐urethane) was prepared by melt‐blending bisphenol‐S/aniline‐type benzoxazine (BS‐a) with isocyanate‐terminated polyurethane (PU) prepolymer based on 2,4‐toluene diisocyanate and poly(ethylene glycol), followed by thermally activated polymerization of the blend. The copolymerization reaction between BS‐a and PU prepolymer was monitored using Fourier transform infrared spectroscopy. The morphology, dynamic mechanical properties, and thermal stability of the poly(benzoxazine‐co‐urethane) were studied using scanning electron microscopy, dynamic mechanical analysis, and thermogravimetry. Homogeneous morphology is shown in scanning electron micrographs of the fracture surfaces of poly(benzoxazine‐co‐urethane)s with different urethane weight fractions, and the roughness of the surface increases with urethane content increasing. Correspondingly, a single glass transition temperature (T_g) is shown on the dynamic mechanical analysis curves of the poly(benzoxazine‐co‐urethane)s, and the T_g is higher than that of the polybenzoxazine. With increase in the urethane content, the T_g and water absorption of poly(benzoxazine‐co‐urethane) increase, whereas the storage modulus and thermal stability decrease. POLYM. ENG. SCI., 53:2633–2639, 2013. © 2013 Society of Plastics Engineers     

Patterned conductive polyaniline films fabricated using lithography and in situ polymerization

In this article, we describe a novel bottom‐up technique for the preparation of transparent conductive films of polyaniline (PANI). A UV‐curable photoresist was formulated containing an acrylate‐endcapped urethane oligomer [UA(PPG400)], acrylic acid, a photoinitiator, and a reactive diluent (tripropylene glycol diacrylate), and the lithography techniques were used to pattern the structure with line widths/spaces of 100 μm/100 μm, 10 μm/10 μm, and 5 μm/5 μm on a polyethylene terephthalate substrate. The carboxylic acid units on the surface of the patterned photoresist interacted with the aniline monomer units to form anilinium complexes; using ammonium persulfate as a chemical oxidant, we then synthesized a layer of conductive PANI on the surface of the patterned resist through in situ polymerization. The optimal conductivity of the PANI conductive film was ca. 10 S/cm. The thin film was characterized, and its physical properties investigated using Fourier transform infrared spectroscopy, UV–Vis spectroscopy, differential scanning calorimetry, optical and atomic force microscopy, and four‐point probe conductivity measurements. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of poly(urethane‐co‐imidine)s having pendent phenyl and benzylidene groups using bisphthalides,bislactones and blocked polyurethane prepolymers

Poly(urethane‐co‐imidine)s were prepared using amine blocked polyurethane (PU) prepolymer. The PU prepolymer was prepared by the reaction of poly(propylene glycol) (PPG₂₀₀₀) and 2,4‐tolylene diisocyanate (TDI) and end capped with N‐methyl aniline. The PU prepolymer was then reacted with bisphthalides and bislactones, until the evolution of carbon dioxide ceased. Polymerization reactions with bispthalides and bislactone took more time than with dianhydrides. Polymers were characterized by FTIR, GPC, TG and DSC analyses. Molecular weights of the poly(urethane‐co‐imidine)s were found to be lower than that of poly(urethane‐co‐imide)s. Compared to poly(urethane‐co‐imide)s all poly(urethane‐co‐imidine)s showed high glass transition temperature and crystallization peak in DSC. The thermal stability of the polyurethanes was found to increase with the introduction of imidine component. © 2001 Society of Chemical Industry     

Effects of thermal imidization on mechanical properties of poly(amide‐co‐imide)/multiwalled carbon nanotube composite films

In this study, experimental and numerical studies were performed to investigate the relationship among the functionalization method, weight fraction of MWCNTs, thermal imidization cycle, and mechanical properties of various PAI/MWCNT composite films. Poly(amide‐co‐imide)/multiwalled carbon nanotube composite films were prepared by solution mixing and film casting. The effects of chemical functionalization and weight fraction of multiwalled carbon nanotubes on thermal imidization and mechanical properties were investigated through experimental and numerical studies. The time needed to achieve sufficient thermal imidization was reduced with increasing multiwalled carbon nanotube content when compared with that of a pure poly(amide‐co‐imide) film because multiwalled carbon nanotubes have a higher thermal conductivity than pure poly(amide‐co‐imide) resin. Mechanical properties of pure poly(amide‐co‐imide) and poly(amide‐co‐imide)/multiwalled carbon nanotube composite films were increased with increasing imidization time and were improved significantly in the case of the composite film filled with hydrogen peroxide treated multiwalled carbon nanotubes. Both the tensile strength and strain to failure of the multiwalled carbon nanotube filled poly(amide‐co‐imide) film were increased substantially because multiwalled carbon nanotube dispersion was improved and covalent bonding was formed between multiwalled carbon nanotubes and poly(amide‐co‐imide) molecules. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis,characterization, and comparison of self‐doped,doped, and undoped forms of polyaniline,poly(o‐anisidine), and poly[aniline‐co‐(o‐anisidine)]

Polyaniline (PANI), poly(o‐anisidine), and poly[aniline‐co‐(o‐anisidine)] were synthesized by chemical oxidative polymerization with ammonium persulfate as an oxidizing reagent in an HCl medium. The viscosities, electrical conductivity, and crystallinity of the resulting polymers (self‐doped forms) were compared with those of the doped and undoped forms. The self‐doped, doped, and undoped forms of these polymers were characterized with infrared spectroscopy, ultraviolet–visible spectroscopy, and a four‐point‐probe conductivity method. X‐ray diffraction characterization revealed the crystalline nature of the polymers. The observed decrease in the conductivity of the copolymer and poly(o‐anisidine) with respect to PANI was attributed to the incorporation of the methoxy moieties into the PANI chain. The homopolymers attained conductivity in the range of 3.97 × 10^?3 to 7.8 S/cm after doping with HCl. The conductivity of the undoped forms of the poly[aniline‐co‐(o‐anisidine)] and poly(o‐anisidine) was observed to be lower than 10^?5 J/S cm^?1. The conductivity of the studied polymer forms decreased by the doping process in the following order: self‐doped → doped → undoped. The conductivity of the studied polymers decreased by the monomer species in the following order: PANI → poly[aniline‐co‐(o‐anisidine)] → poly(o‐anisidine). All the polymer samples were largely amorphous, but with the attachment of the pendant groups of anisidine to the polymer system, the crystallinity region increased. The undoped form of poly[aniline‐co‐(o‐anisidine)] had good solubility in common organic solvents, whereas doped poly[aniline‐co‐(o‐anisidine)] was moderately crystalline and exhibited higher conductivity than the anisidine homopolymer. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Synthesis and characterization of statistical copolymers of styrene and 4‐(1‐hydroxyalkyl)styrene

A family of new polymers based on poly(4‐(1‐hydroxyalkyl)styrene), and its copolymers with styrene were synthesized and thoroughly characterized by ¹H‐NMR, ¹³C‐NMR, FTIR, and UV spectroscopies. The chemical modification reactions of polystyrene (PS) was used as a novel method of performing the synthesis of poly(4‐(1‐hydroxyethyl‐co‐styrene)), poly(4‐(1‐hydroxypropyl‐co‐styrene)), poly(4‐(1‐hydroxybutyl‐co‐styrene)), and poly(4‐(1‐hydroxyphenylmethyl‐co‐styrene)). The novelty of this method lies in the incorporation of the desired mol % of the functional groups in polystyrene chain, to obtain random copolymers of desired composition. In preliminary testing/evaluation studies the utility and versatility of the new copolymers, which have the potential to be negative‐tone photoresist materials, were studied. Thus a few photoresist formulations based on poly(styrene‐co‐4‐(1‐hydroxyalkylstyrene)) were developed with 5 wt % of a photoacid generator. These studies suggested that the new copolymers synthesized by a simple and alternate method could have the same potential as a photoresist material when compared with the polymers synthesized by the polymerization of the corresponding functional monomer. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1902–1914, 2004     

Preparation and performance of a transparent poly(3,4‐ethylene dioxythiophene)–poly(p‐styrene sulfonate‐co‐acrylic acid sodium) film with a high stability and water resistance

Poly(p‐styrene sulfonate‐co‐acrylic acid sodium) (PSA) from the copolymerization of acrylic acid sodium and p‐styrene sulfonate monomers were used to dope poly(3,4‐ethylene dioxythiophene) (PEDOT) to generate PEDOT–PSA antistatic dispersions. Compared to those of the PEDOT–poly(p‐styrene sulfonate sodium) (PSS), the physical and electrical properties of the PEDOT–PSA conductive liquids were much better. The PEDOT–PSA films possessed a better water resistance without a decrease in the conductivity. The sheet resistance of the PEDOT–PSA–poly(ethylene terephthalate) (PET) films was about 1.5 × 10⁴ Ω/sq with a 100 nm thickness, the same as the PEDOT–PSS–PET films. The transmittance of the PEDOT–PSA–PET films exceeded 88%. Furthermore, the environmental dispersity of the PEDOT–PSA antistatic dispersion was apparently improved by the dopant PSA so that the stability was extraordinarily promoted. Meanwhile, the water resistances of the PEDOT–PSA–PET and PEDOT–PSA films were also enhanced. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45163.     

Investigation of sensing effects of polystyrene‐graft‐polyaniline for cyanide compounds

Polyaniline and its derivatives have high antioxidative stability and are considered to belong to the most useful conductive polymers for practical application. In this work, we have linked 1,4‐phenylenediamine to poly(styrene‐co‐chloromethylstyrene) and prepared poly(styrene‐co‐p‐aminoanilinemethylstyrene), poly(S‐co‐PAAMS). Polystyrene‐graft‐polyaniline, (PS‐g‐PANi), has been synthesized by adding solution of ammonium persulfate and p‐toluenesufonic acid in water. The conductivity of these polymers was measured by the four‐point probe method. The copolymers produced exhibit electrical conductivity comparable to that of polyaniline. PS‐g‐PANi was also exposed to some cyanide compounds such as hydrocyanic acid (Hydrogen cyanide‐HC), ethanedinitrile (Cyanogen‐CY), cyanogen chloride (Chlorocyan‐CC), and cyanogen bromide (Bromocyan‐BC). The cyanide compounds are classified as blood agents groups, in terms of chemical warfare agents standards. First, we prepared different concentration of blood agents at 50, 100, and 150 ppm and exposed them on PS‐g‐PANi for 2 min. Second, we have drawing conductivity change curves versus time and produced optimum conductivity versus time taken. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3920–3926, 2006     

Synthesis and characterization of conducting homopolymers and copolymers of o‐anisidine and o‐toluidine in inorganic and organic supporting electrolytes

The influence of inorganic and organic supporting electrolytes on the electrochemical, optical, and conducting properties of poly(o‐anisidine), poly(o‐toluidine), and poly(o‐anisidine‐co‐o‐toluidine) thin films was investigated. Homopolymer and copolymer thin films were synthesized electrochemically, under cyclic voltammetry conditions, in aqueous solutions of inorganic acids (H₂SO₄, HCl, HNO₃, H₃PO₄, and HClO₄) and organic acids (benzoic acid, cinnamic acid, oxalic acid, malonic acid, succinic acid, and adipic acid) at room temperature. The films were characterized by cyclic voltammetry, ultraviolet–visible spectroscopy, and conductivity measurements with a four‐probe technique. The ultraviolet–visible spectra were obtained ex situ in dimethyl sulfoxide. The optical absorption spectra indicated that the formation of the conducting emeraldine salt (ES) phase took place in all the inorganic electrolytes used, whereas in organic acid supporting electrolytes, ES formed only with oxalic acid. Moreover, the current density and conductivity of the thin films was greatly affected by the nature and size of the anion present in the electrolyte. For the copolymer, the conductivity lay between the conductivity of the homopolymers, regardless of the supporting electrolyte used. The formation of the copolymer was also confirmed with differential scanning colorimetry. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2634–2642, 2003     

Electrochemical synthesis of poly(2‐iodoaniline) and poly(aniline‐co‐2‐iodoaniline) in acetonitrile

Poly(2‐iodoaniline) (PIANI) and poly(aniline‐co‐2‐iodoaniline) [P(An‐co‐2‐IAn)] were synthesized by electrochemical methods in acetonitrile solution containing tetrabutylammonium perchlorate (TBAP) and perchloric acid (HClO₄). The voltametry of the copolymer shows characteristics similar to those of conventional polyaniline (PANI), and it exhibits higher dry electrical conductivity than PIANI and lower than PANI. The observed decrease in the conductivity of the copolymer relative to PANI is attributed to the incorporation of the iodine moieties into the PANI chain. The structure and properties of these conducting films were characterized by FTIR and UV‐Vis spectroscopy and by an electrochemical method (cyclic voltametry). Conductivity values, FTIR and UV‐Vis spectra of the PIANI and copolymer were compared with those of PANI and the relative solubility of the PIANI and the copolymer powders was determined in various organic solvents. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1652–1658, 2003     

Self‐assembled poly(styrene‐co‐N‐isopropylacrylamide) film induced by capillary force

The monodisperse poly(styrene‐co‐N‐isopropylacrylamide) (poly(St‐co‐NIPAAm)) particles prepared by emulsifier‐free emulsion polymerization with microwave irradiation were induced by capillary forces to self‐assemble, and formed the two‐dimensional films on the clean glassware wafer substrates. The morphologies of the two‐dimensional films were characterized by scanning electron microscopy (SEM) and atom force microscopy (AFM). The results showed that monodisperse poly(St‐co‐NIPAAm) particles could form ordered two‐dimensional films by capillary forces. With NIPAAm concentration increasing, there gradually appeared surface undulations or surface defective region on the two‐dimensional films. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3514–3519, 2006     

Ultrasonochemical‐assisted fabrication and evaporation‐ induced self‐assembly (EISA) of POSS‐SiO2@Ag core/ABA triblock copolymer nanocomposite film

Poly(ethylene glycol)‐octafunctionalized polyhedral oligomeric silsesquioxane (POSS) (M_n = 5576.6 g/mol) alloying agent stabilized amphiphilic silica@silver metalloid nanocomposite blended with a triblock copolymer poly(p‐dioxanone‐co‐caprolactone)‐block‐poly(ethylene oxide)‐block‐poly(p‐dioxanone‐co‐caprolactone) (POSS‐SiO₂@Ag/PPDO‐co‐PCL‐b‐PEG‐b‐PPDO‐co‐PCL) has been synthesized in both water and in organic medium utilizing ultrasonochemical reaction. The POSS stabilized pre‐made metalloid was successfully dispersed in amphiphilic PPDO‐co‐PCL‐b‐PEG‐b‐PPDO‐co‐PCL (ABA) triblock copolymer matrix of molecular weight 45.9 × 10⁴ g/mol. The mechanism of synthesis of high concentration of SiO₂@Ag nanocomposite from TEOS/AgNO₃ (in the presence of NH₄OH as catalyst/NaBH₄ as reductant) nonmetal/metal precursors and the successful EISA of POSS‐SiO₂@Ag/ABA nanocomposite into films has been discussed. The successful synthesis of metalloid nanocomposite was morphologically accessed by field emission‐scanning electron microscopy, transmission electron microscopy and atomic force microscopy. Surface plasmon resonance was ensured from UV–visible spectral analysis. Identity and the crystallinity of as prepared nanocomposite were studied by X‐ray diffractometer. Structural and luminescence properties of the nanocomposite were examined by Fourier transform infrared spectroscopy and photoluminescence. Thermogravimetric analysis was carried out to study the thermal stability of the resulting hybrid nanocomposite. The resultant inorganic–organic nanocomposite can be easily suspended in water and would be useful in variety of applications. POLYM. COMPOS., 31:1620–1627, 2010. © 2009 Society of Plastics Engineers     

Free‐standing hybrid anion‐exchange membranes for application in fuel cells

A series of free‐standing hybrid anion‐exchange membranes were prepared by blending brominated poly(2,6‐dimethyl‐1,4‐phenylene oxide) (BPPO) with poly(vinylbenzyl chloride‐co‐γ‐methacryloxypropyl trimethoxy silane) (poly(VBC‐co‐γ‐MPS)). Apart from a good compatibility between organic and inorganic phases, the hybrid membranes had a water uptake of 32.4–51.8%, tensile strength around 30 MPa, and T_d temperature at 5% weight loss around 243–261°C. As compared with the membrane prepared from poly (VBC‐co‐γ‐MPS), the hybrid membranes exhibited much better flexibility, and larger ion‐exchange capacity (2.19–2.27 mmol g^?1) and hydroxyl (OH^?) conductivity (0.0067–0.012 S cm^?1). In particular, the hybrid membranes with 60–75 wt % BPPO had the optimum water uptake, miscibility between components, and OH^? conductivity, and were promising for application in fuel cells. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Poly(dimethylsiloxane)urethane‐co‐poly(methyl methacrylate) with 2,4‐toluene diisocyanate and m‐xylene diisocyanate. I. Compatibility and impact strength of copolymers

In this study, slightly crosslinked poly(dimethylsiloxane)urethane‐co‐poly(methyl methacrylate) (PDMS urethane‐co‐PMMA) graft copolymers based on two diisocyanates, 2,4‐toluene diisocyanate (2,4‐TDI) and m‐xylene diisocyanate (m‐XDI), were successfully synthesized. Glass‐transition behaviors of the copolymers were investigated. Results confirm that PDMS–urethane and PMMA are miscible in the 2,4‐TDI system, but are only partially miscible in the m‐XDI system. The methylene groups adjoining the isocyanate in the m‐XDI system show increased phase‐separation behavior over the 2,4‐TDI system, in which the benzene ring adjoins the isocyanate. The functional group of PDMS–urethane improves the impact strength of the copolymers. The toughness depends on the compatibility of PDMS–urethane and PMMA segments in the copolymers. In the m‐XDI system, the impact strength of the copolymer containing 3.75 phr macromonomer achieves a maximum value (from 13.02 to 22.21 J/m). The fracture behavior and impact strength of the copolymers in the 2,4‐TDI system are similar to that of PMMA homopolymer, although they are independent of the macromonomer content in the copolymer. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1875–1885, 2002     

Polymer gel electrolytes prepared from P(EG‐co‐PG) and their nanocomposites using organically modified montmorillonite

Polymer gel electrolytes were prepared by thermal crosslinking reaction of a series of acrylic end‐capped poly(ethylene glycol) and poly(propylene glycol) [P(EG‐co‐PG)] having various geometries and molecular weights. Acrylic end‐capped prepolymers were prepared by the esterification of low molecular weight (M_n: 1900–5000) P(EG‐co‐PG) with acrylic acid. The linear increase in the ionic conductivity of polymer gel electrolyte films was observed with increasing temperature. The increase in the conductivity was also monitored by increasing the molecular weight of precursor polymer. Nanocomposite electrolytes were prepared by the addition of 5 wt % of organically modified layered silicate (montmorillonite) into the gel polymer electrolytes. The enhancement of the ionic conductivity as well as mechanical properties was observed in the nanocomposite systems. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 894–899, 2004     

A conductive foam: Based on novel poly(styrene‐b‐butadiene‐co‐styrene‐b‐styrene) tri‐block copolymer filled by carbon black

In this article, a conductive foam based on a novel styrene‐based thermoplastic elastomer called poly(styrene‐b‐butadiene‐co‐styrene‐b‐styrene) tri‐block copolymer S(BS)S was prepared and introduced. S(BS)S was particularly designed for chemical foaming with uniform fine cells, which overcame the shortcomings of traditional poly(styrene‐b‐butadiene‐b‐styrene) tri‐block copolymer (SBS). The preparation of conductive foams filled by the carbon black was studied. After the detail investigation of cross‐linking and foaming behaviors using moving die rheometer, the optimal foaming temperature was determined at 180°C with a complex accelerator for foaming agent. Scanning electron microscopy (SEM) images shown that the cell bubbles of conductive foam were around 30–50 µm. The conductivity of foams was tested using a megger and a semiconductor performance tester. SEM images also indicated that the conductivity of foams was mainly affected by the distribution of carbon black in the cell walls. The formation of the network of the carbon black aggregates had a contribution to perfect conductive paths. It also found that the conductivity of foams declined obviously with the foaming agent content increasing. The more foaming agent led to a sharp increasing of the number of cells (from 2.93 × 10⁶ to 6.20 × 10⁷ cells/cm³) and a rapid thinning of the cell walls (from 45.3 to 1.4 µm), resulting in an effective conductive path of the carbon black no forming. The conductive soft foams with the density of 0.48–0.09 g/cm³ and the volume resistivity of 3.1 × 10³?2.5 × 10⁵ Ω cm can be easily prepared in this study. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41644.     

Competitive hydrogen bonding mechanisms underlying phase behavior of triple poly(N‐vinyl pyrrolidone)–poly(ethylene glycol)–poly(methacrylic acid‐co‐ethylacrylate) blends

Differential scanning calorimetry (DSC) of triple blends of high molecular weight poly(N‐vinyl pyrrolidone) (PVP) with oligomeric poly(ethylene glycol) (PEG) of molecular weight 400 g/mol and copolymer of methacrylic acid with ethylacrylate (PMAA‐co‐EA) demonstrates partial miscibility of polymer components, which is due to formation of interpolymer hydrogen bonds (reversible crosslinking). Because both PVP and PMAA‐co‐EA are amorphous polymers and PEG exhibits crystalline phase, the DSC examination is informative on the phase state of PEG in the triple blends and reveals a strong competition between PEG and PMAA‐co‐EA for interaction with PVP. The hydrogen bonding in the triple PVP–PEG–PMAA‐co‐EA blends has been established with FTIR Spectroscopy. To evaluate the relative strengths of hydrogen bonded complexes in PVP–PEG–PMAA‐co‐EA blends, quantum‐chemical calculations were performed. According to this analysis, the energy of H‐bonding has been found to diminish in the order: PVP–PMAA‐co‐EA–PEG(OH) > PVP–(OH)PEG(OH)–PVP > PVP–H₂O > PVP–PEG(OH) > PMAA‐co‐EA–PEG(? O? ) > PVP–PMAA‐co‐EA > PMAA‐co‐EA–PEG(OH). Thus, most stable complexes are the triple PVP–PMAA‐co‐EA–PEG(OH) complex and the complex wherein comparatively short PEG chains form simultaneously two hydrogen bonds to PVP carbonyl groups through both terminal OH‐groups, acting as H‐bonding crosslinks between longer PVP backbones. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and characterization of a copolymer: Poly(aniline‐co‐fluoroaniline)

In the present article, we report the chemical synthesis and characterization of poly(aniline‐co‐fluoroaniline) [poly(An‐FAn)]. The copolymerization of aniline and 2‐fluoroaniline was carried out by chemical method in acidic medium. The characterization of poly(aniline‐co‐fluoroaniline) was done using FTIR, UV‐visible spectroscopy, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron micrography (SEM), and a four‐points‐probe conductivity method. X‐ray diffraction (XRD) and SEM characterization reveal crystalline nature of doped copolymer compared to undoped copolymer. The observed decrease in the conductivity of the copolymer relative to polyaniline is attributed to the incorporation of the fluoro moieties into the polyaniline chain. The chemically synthesized copolymer shows good solubility in common organic solvents, and is, therefore, technological useful. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1460–1466, 2001     

Controllable synthesis and characterization of poly(aniline‐co‐pyrrole) using anionic spherical polyelectrolyte brushes as dopant and template

A poly(aniline‐co‐pyrrole), using anionic spherical polyelectrolyte brushes (ASPB) as dopant and template, was synthesized by chemical oxidation polymerization. The composites were characterized by scanning electron microscopy (SEM), Fourier‐transform infrared spectrometry (FTIR), X‐ray diffraction (XRD), and electrical studies. The SEM images confirmed that the composites had a spherical‐like structure, with a size of ca. 170 nm. The FTIR spectra showed the intermolecular interaction between poly(aniline‐co‐pyrrole) and ASPB. The XRD analysis revealed that the interplanar distance of the copolymers increased from 0.373 nm to 0.391 nm. The electrical conductivity of the poly(aniline‐co‐pyrrole)/ASPB nanocomposites at room temperature was 8.3 S cm⁻¹, higher than that of the conducting copolymers (2.1 S cm⁻¹). These conductive nanocomposites have nanoparticle size, controllable morphology, and the potential for application in inkjet electronic printing. POLYM. COMPOS., 35:1858–1863, 2014. © 2014 Society of Plastics Engineers