Miscibility and crystallization in crystalline/crystalline blends of poly(butylene succinate)/poly(ethylene oxide)

Miscibility and crystallization behavior have been investigated in blends of poly(butylene succinate) (PBSU) and poly(ethylene oxide) (PEO), both semicrystalline polymers, by differential scanning calorimetry and optical microscopy. Experimental results indicate that PBSU is miscible with PEO as shown by the existence of single composition dependent glass transition temperature over the entire composition range. In addition, the polymer-polymer interaction parameter, obtained from the melting depression of the high-T_m component PBSU using the Flory-Huggins equation, is composition dependent, and its value is always negative. This indicates that PBSU/PEO blends are thermodynamically miscible in the melt. The morphological study of the isothermal crystallization at 95 °C (where only PBSU crystallized) showed the similar crystallization behavior as in amorphous/crystalline blends. Much more attention has been paid to the crystallization and morphology of the low-T_m component PEO, which was studied through both one-step and two-step crystallization. It was found that the crystallization of PEO was affected clearly by the presence of the crystals of PBSU formed through different crystallization processes. The two components crystallized sequentially not simultaneously when the blends were quenched from the melt directly to 50 °C (one-step crystallization), and the PEO spherulites crystallized within the matrix of the crystals of the preexisted PBSU phase. Crystallization at 95 °C followed by quenching to 50 °C (two-step crystallization) also showed the similar crystallization behavior as in one-step crystallization. However, the radial growth rate of the PEO spherulites was reduced significantly in two-step crystallization than in one-step crystallization.     

Miscibility and crystallization of poly(ethylene succinate)/poly(vinyl phenol) blends

Miscibility of biodegradable poly(ethylene succinate) (PES)/poly(vinyl phenol) (PVPh) blends has been studied by differential scanning calorimetry (DSC) in this work. PES is found to be miscible with PVPh as shown by the existence of single composition dependent glass transition temperature over the entire composition range. Spherulitic morphology and the growth rates of neat and blended PES were investigated by optical microscopy (OM). Both neat and blended PES show a maximum growth rate value in the crystallization temperature range of 45-65 °C, with the growth rate of neat PES being higher than that of blended PES at the same crystallization temperature. The overall crystallization kinetics of neat and blended PES was also studied by DSC and analyzed by the Avrami equation at 60 and 65 °C. The crystallization rate decreases with increasing the temperature for both neat and blended PES. The crystallization rate of blended PES is lower than that of neat PES at the same crystallization temperature. However, the Avrami exponent n is almost the same despite the blend composition and crystallization temperature, indicating that the addition of PVPh does not change the crystallization mechanism of PES but only lowers the crystallization rate.     

Mechanical behavior of double-C60-end-capped poly(ethylene oxide)

Double-C₆₀-end-capped poly(ethylene oxide) (PEO) possesses good mechanical properties arising from a network-like structure due to the aggregation of C₆₀. The tensile strength is about 20 MPa, the elongation at break exceeds 640% and the fracture toughness is more than 110 MJ/m³. The material also possesses shape recovery ability. In contrast, single-C₆₀-end-capped PEO does not possess good mechanical properties.     

Miscibility and crystallization of poly(ethylene oxide) and poly(ε-caprolactone) blends

Blends of poly(ethylene oxide) (PEO) with poly(ε-caprolactone) (PCL), both semicrystalline polymers, were prepared by co-dissolving the two polyesters in chloroform and casting the mixture. Phase contrast microscopy was used to probe the miscibility of PEOB/PCL blends. Experimental results indicated that PEO was immiscible with PCL because the melt was biphasic. Crystallization of PEO/PCL blends was studied by differential scanning calorimetry and analyzed by the Avrami equation. The crystallization rate of PEO decreased with the increase of PCL in the blends while the crystallization mechanism did not change. In the case of the isothermal crystallization of PCL, the crystallization mechanism did not change, and the change in the crystallization rate was not very big, or almost constant with the addition of PEO, compared with the change of the crystallization rate of PEO.     

Miscibility and interactions in poly(methylthiomethyl methacrylate)/poly(vinyl alcohol) blends

Poly(methylthiomethyl methacrylate) (PMTMA) is miscible with poly(vinyl alcohol) (PVA) over the whole composition range as shown by the existence of a single glass transition temperature in each blend. The interaction between PMTMA and PVA was examined by Fourier transform infrared spectroscopy, solid-state nuclear magnetic resonance spectroscopy and X-ray photoelectron spectroscopy. The interactions mainly involve the hydroxyl groups of PVA and the thioether sulfur atoms of PMTMA, and the involvement of the carbonyl groups of PMTMA in interactions is not significant. The measurements of proton spin-lattice relaxation time reveal that PMTMA and PVA do not mix intimately on a scale of 1-3 nm, but are miscible on a scale of 20-30 nm. In comparison, we have previously found that PMTMA is miscible with poly(p-vinylphenol) and the two polymers mix intimately on a scale of 1-3 nm.     

Miscibility and hydrogen bonding in blends of poly(vinyl acetate) with phenolic resin

The miscibility of phenolic resin and poly(vinyl acetate) (PVAc) blends was investigated by differential scanning calorimeter (DSC), Fourier transform infrared spectroscopy (FT-IR) and solid state ¹³C nuclear magnetic resonance (NMR). This blend displays single glass transition temperature (T_g) over entire compositions indicating that this blend system is miscible in the amorphous phase due to the formation of hydrogen bonding between hydroxyl groups of phenolic resin and carbonyl groups of PVAc. Quantitative measurements on fraction of hydrogen-bonded carbonyl group using both ¹³C solid-state NMR and FT-IR analyses result in good agreement between these two spectroscopic techniques. According to the proton spin-lattice relaxation time in the rotating frame (T_1ρ^H), the phenolic/PVAc blend is intimately mixed on a scale less than 2-3 nm. Furthermore, the inter-association equilibrium constant and its related enthalpy of phenolic/PVAc blends were determined as a function of temperatures by infrared spectra based on the Painter-Coleman association model.     

Orientation relaxation study on poly(ethylene oxide)-poly(vinyl phenol) blends by polarization modulation infrared linear dichroism

Orientation relaxation in miscible poly(vinyl phenol) (PVPh)-poly(ethylene oxide) (PEO) blends (from 25 to 40 wt% PEO) was investigated using polarization modulation infrared linear dichroism. This blend was selected to study the effect of strong hydrogen bonds on relaxation. The results show that PEO is more oriented than PVPh, and remains so throughout the experimental relaxation time. Relaxation proceeds in three stages. PVPh relaxation is systematically faster than that of PEO, while PEO relaxation times increase steadily with increasing PEO content. For PVPh, a maximum in relaxation times is observed around 30 wt% PEO. Relaxation coupling occurs for concentrations in PEO lower than 30 wt%, is marginal for the 35 wt% and clearly absent for the 40 wt% PEO blend. By comparison with previous rheology and near-infrared data, it can be concluded that hydrogen bonds do not automatically insure cooperativity during relaxation: for cooperativity to occur, the minor component of the blend must interact preferentially with the major component. This is the case of PVPh-rich compositions, but not for PEO-rich compositions (for 35 and 40 wt% PEO), for which the minor PVPh constituent interacts strongly with both PEO and other PVPh chains.     

Poly(hydroxyether sulfone) and its blends with poly(ethylene oxide): miscibility, phase behavior and hydrogen bonding interactions

Poly(hydroxyether sulfone) (PHES) was synthesized through polycondensation of bisphenol S with epichlorohydrin. It was characterized by Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance spectroscopy and differential scanning calorimetry (DSC). The miscibility in the blends of PHES with poly(ethylene oxide) (PEO) was established on the basis of the thermal analysis results. DSC showed that the PHES/PEO blends prepared by casting from N,N-dimethylformamide (DMF) possessed single, composition-dependent glass transition temperatures (T_gs), indicating that the blends are miscible in amorphous state. At elevated temperatures, the PHES/PEO blends underwent phase separation. The phase behavior was investigated by optical microscope and the cloud point curve was determined. A typical lower critical solution temperature behavior was observed in the moderate temperature range for this blend system. FTIR studies indicate that there are the competitive hydrogen bonding interactions upon adding PEO to the system, which was involved with the intramolecular and intermolecular hydrogen bonding interactions, i.e. -OH?OS, -OH?-OH and -OH versus ether oxygen atoms of PEO between PHES and PEO. In terms of the infrared spectroscopic investigation, it is judged that from weak to strong the strength of the hydrogen bonding interactions is in the following order: -OH?OS, -OH?-OH and -OH versus ether oxygen atoms of PEO.     

Dehydrochlorination of poly(vinyl chloride) modified with titanium dioxide/poly(ethylene oxide) based paint photocatalysts

The dehydrochlorination of poly(vinyl chloride) (PVC) film samples modified with titanium dioxide (TiO₂)/poly(ethylene oxide) (PEO) based paint photocatalysts [the addition of methyl linoleate (ML) or methyl oleate (MO)] was performed. After 24 h of UV photoirradiation, the sample with TiO₂/PEO showed that there existed a structure with the longest polyene length, whereas that with TiO₂/PEO/ML contained the most polyene structures. The chloroform‐soluble fraction of the sample with TiO₂/PEO contained a poly(vinyl alcohol) (PVA) structure instead of a polyene one and showed a novel method of PVA production via PVC photodegradation. The molecular weight curve of the fraction shifted slightly to a lower molecular weight compared to that without the photocatalyst; this showed that slight polymer chain scission occurred. The ¹H‐NMR and ¹³C‐NMR spectra showed that the content of PVA units was about 20%, and the PVA sequence was blocky. The fraction of the sample with TiO₂/PEO/ML contained the highest methyl group content; this showed that the branch degree was highest as was the polyene content. These highest contents were due to the existence of the grafted ML. Pyrolysis gas chromatography/mass spectroscopy measurements suggested that there existed more polyene and graft units in the chloroform‐insoluble fractions of the samples with TiO₂/PEO, TiO₂/PEO/ML, and TiO₂/PEO/MO, respectively. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40760.     

Studies on aluminum-isopropoxide doped poly(ethylene oxide), poly(vinyl alcohol), and poly(ethylene oxide)-poly(vinyl alcohol) blends

Poly(ethylene oxide), poly(vinyl alcohol), and their blend in a 40 : 60 mole ratio were doped with aluminum isopropoxide. Their structural, thermal, and electrical properties were studied. Aluminum isopropoxide acts as a Lewis acid and thus significantly influences the electrical properties of the polymers and the blend. It also acts as a scavanger for the trace quantities of water present in them, thereby reducing the magnitude of proton transport. It also affects the structure of polymers that manifests in the thermal transformation and decomposition characteristics. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 2147–2157, 1998     

Miscibility of segmented polyurethane/poly(vinyl chloride) blends

Miscibilities of segmented polyurethanes (SPUs) and poly(vinyl chloride) (PVC) or functionalized poly(vinyl chloride) (FPVC) were studied with dynamic mechanical analysis, differential scanning calorimetry, and X‐ray diffraction. Mechanical properties of the blends were also studied with tensile measurements. The miscibility of the blends depended greatly on the hard‐segment content of SPU and the existence of the functional groups. The combination of SPU with a low hard‐segment content and PVC with functional groups made the blend system miscible. Moreover, controlling the blend composition of SPU/FPVC allowed us to modify the mechanical properties of SPU, where the elongation at break was multiplied without a significant change in its tensile strength. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 3022–3029, 2001     

Properties of Poly(vinyl chloride)/poly(ethylene oxide)/polyaniline Conductive Films: The Effect of Poly(ethylene glycol) Diglycidyl Ether

The effect of polyaniline and poly(ethylene glycol) diglycidyl ether on tensile properties, morphology, thermal degradation, and electrical conductivity of poly(vinyl chloride)/poly(ethylene oxide)/polyaniline conductive films was studied. The poly(vinyl chloride)/poly(ethylene oxide)/polyaniline conductive films were prepared using a solution casting technique at room temperature until a homogeneous solution was produced. Poly(vinyl chloride)/poly(ethylene oxide)/polyaniline/poly(ethylene glycol) diglycidyl ether conductive films exhibit higher electrical properties, tensile strength, modulus of elasticity but lower final decomposition temperature than poly(vinyl chloride)/poly(ethylene oxide)/polyaniline conductive films. Scanning electron microscopy morphology showed that the polyaniline more widely dispersed in the poly(vinyl chloride)/poly(ethylene oxide) blends with the addition of poly(ethylene glycol) diglycidyl ether as surface modifier.     

Poly(ethylene oxide) and its blends with sodium alginate

A series of blends based on poly(ethylene oxide) (PEO) and sodium alginate (NaAlg) were prepared by solution casting method. The blends thus obtained were characterized by using Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), tensile strength test, contact angle measurements and atomic force microscopy (AFM). FT-IR studies indicate that there are the hydrogen bonding interactions due to the ether oxygen of PEO and the hydroxyl groups of NaAlg. The thermal stability of the blends was slightly affected with increasing NaAlg content. DSC results showed that both melting point and crystallinity depend on the composition of the blends. Mechanical properties of the blend films were improved compared to those of homopolymers. Surface free energy components of the blend films were calculated from contact angle data of various liquids by using Van Oss-Good methodology. It was found that the surfaces both of the blends are enriched in low surface free energy component, i.e. NaAlg. This conclusion was further confirmed by the AFM images observation of the surface morphology of these blends.     

Low environmental sensitive antistatic material based on poly(vinyl chloride)/quaternary ammonium salt by blending with poly(ethylene oxide)

A quaternary ammonium salt (QAS) was synthesized and characterized by ¹H NMR. A low environmental sensitive antistatic plasticized poly(vinyl chloride) (PPVC) was prepared by blending with QAS and poly(ethylene oxide) (PEO). The structure and properties of PPVC/QAS/PEO blend were studied by scanning electronic microscope (SEM), surface resistivity, and mechanical properties tests. The results show that the surface resistivity of PPVC/QAS/PEO (100/4.5/0) blend without PEO component can be reduced to less than 3.0 × 10⁸ Ω at 65% environmental humidity, which satisfied the antistatic property requirement related to MT113‐1995 of China. However, QAS, similar to other commercial antistatic agents, is much sensitive to environmental humidity. When a small amount of PEO is added, the surface resistivity of PPVC/QAS/PEO blend has a quite low sensitivity to environmental humidity and further reduces. An excellent antistatic property of PPVC/QAS/PEO blend under low humidity can be achieved. Its tensile strength and elongation at break are also improved with PEO addition. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Miscibility and phase behavior in thermosetting blends of polybenzoxazine and poly(ethylene oxide)

Thermosetting polymer blends composed of polybenzoxazine (PBA-a) and poly(ethylene oxide) (PEO) were prepared via in situ curing reaction of benzoxazine (BA-a) in the presence of PEO, which started from the initially homogeneous mixtures of BA-a and PEO. Before curing, the BA-a/PEO blends displayed the single and composition-dependant glass transition temperatures (T_g's) in the entire blend composition, and the equilibrium melting point depression was also observed in the blends. It is judged that the BA-a/PEO blends are completely miscible. The miscibility was mainly ascribed to the contribution of entropy to mixing free energy since the molecular weight of BA-a is rather low. However, phase separation occurred after curing reaction at the elevated temperature, which was confirmed by differential scanning calorimetry (DSC) and scanning electronic microscopy (SEM). It was expected that the PBA-a/PEO blends would be miscible since PBA-a possesses a great number of phenolic hydroxyls in the molecular backbone, which are potential to form the intermolecular hydrogen bonding interactions with oxygen atoms of PEO and thus would fulfill the miscibility of the blends. To interpret the experimental results, we investigated the variable temperature Fourier transform infrared spectroscopy (FTIR) of the blends via model compound. The FTIR results indicate that the phenolic hydroxyl groups could not form the efficient intermolecular hydrogen bonding interactions at the elevated temperatures (e.g. the curing temperatures), i.e. the phenolic hydroxyl groups existed mainly in the non-associated form in the system. Therefore, the decrease of the mixing entropy still dominates the phase behavior of thermosetting blends at the elevated temperature.     

Miscibility of polystyrene with poly(ethylene oxide) and poly(ethylene glycol)

The intrinsic viscosity of polystyrene–poly(ethylene oxide) (PS–PEO) and PS–poly(ethylene glycol) (PEG) blends have been measured in benzene as a function of blend composition for various molecular weights of PEO and PEG at 303.15 K. The compatibility of polymer pairs in solution were determined on the basis of the interaction parameter term, Δb, and the difference between the experimental and theoretical weight-average intrinsic viscosities of the two polymers, Δ[η]. The theoretical weight-average intrinsic viscosities were calculated by interpolation of the individual intrinsic viscosities of the blend components. The compatibility data based on [η] determined by a single specific viscosity measurement, as a quick method for the determination of the intrinsic viscosity, were compared with that obtained from [η] determined via the Huggins equation. The effect of molecular weights of the blend components and the polymer structure on the extent of compatibility was studied. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 1471–1482, 1998     

Blends of poly(ethylene oxide) and poly(4-vinylphenol-co-2-hydroxyethyl methacrylate): thermal analysis, morphological behaviour and specific interactions

DSC and optical microscopy were used to determine the miscibility and crystallinity of blends of poly(ethylene oxide) (PEO) with poly(4-vinylphenol-co-2-hydroxyethyl methacrylate) (PVPh-HEM). A single glass transition temperature was observed for all blends, indicating miscibility. A progressive decrease in the degree of crystallinity and in the size of the PEO spherullites is observed, as PVPh-HEM is added. FTIR was used to probe the intermolecular specific interactions of the blends and the miscibility of the blend is mainly attributed to PVPh-HEM/PEO intermolecular interactions via hydrogen bonding.     

Tacticity effects on the miscibility behavior of poly(methyl methacrylate)/poly(ethylene oxide-b-dimethylsiloxane-b-ethylene oxide) blends

The miscibility of a triblock copolymer poly(ethylene oxide)-poly(dimethylsiloxane)-poly(ethylene oxide) with syndiotactic and isotactic poly(methylmethacrylate) wasstudied. Although isotactic poly(methyl methacrylate) (PMMA) was miscible with poly(ethylene oxide) (PEO) in the pure state, it was immiscible with the PEO end blocks in the copolymer. In comparison, the syndiotactic poly(methyl methacrylate) (sPMMA) was miscible with the PEO blocks as indicated by melting point depression, decrease in crystallinity, and slower rate of spherulite growth of PEO. When blends of the triblock copolymer were cooled to low temperatures, the poly(dimethylsiloxane) (PDMS) middle block which resided in the interlamellar region of PEO spherulites also crystallized; the development of PDMS crystals was clearly suppressed at high sPMMA contents.On leave from Union Chemical Laboratories, Industrial Technology Research Institute, Hsinchu, Taiwan     

Formation of dendrite crystals in poly(ethylene oxide) interacting with bioresourceful tannin

A dendritic morphology, induced by miscibility with strong intermolecular interaction between poly(ethylene oxide) (PEO) and bioresourceful tannin [tannic acid (TA)]. Mechanism was investigated by differential scanning calorimetry (DSC), Fourier-transform infrared spectroscopy, wide-angle X-ray diffraction, and polarized optical microscopy. The cell crystallography preference in correlation to the intermolecular interaction in the dendrites in PEO/TA (70/30) blend was analyzed. Dendritic morphology was more distinct at PEO/TA = 70/30 composition, where the spherulitic growth rate showed a highly nonlinear relationship with respect to crystallization time (R α t ^1/2). Diffusion limitation mechanism caused by the crystallography preference attributed to the strong intermolecular interaction between PEO and TA was at work.     

Reduction of poly(vinyl chloride) with tri-n-butyltin hydride

Reduction of PVC with tributyl-tin-hydride (Bu₃SnH) was studied in order to optimize the method. The reactions were carried out in mixtures of xylene and tetrahydrofuran, chlorine content was determined by ¹H n.m.r. spectroscopy, and the melting behaviour by d.s.c. It was possible to obtain a product with less than 0.1% chlorine in less than 6 h. The ¹³C n.m.r. spectrum showed that the product contained about 4 methyl branches per 1000 monomer units and gave no evidence of chlorinated structures.