Effect of CO2 in the feed stream on the deactivation of Co/γ-Al2O3 Fischer–Tropsch catalyst

The influence of CO₂ on the deactivation of Co/γ-Al₂O₃ Fischer–Tropsch (FT) catalyst in CO hydrogenation has been investigated. The presence of CO₂ in the feed stream reveals a negative effect on catalyst stability and in the formation of heavy hydrocarbons. The CO₂ acts as a mild oxidizing agent on cobalt metal during Fischer–Tropsch synthesis. During FT synthesis on Co/γ-Al₂O₃ of 70 h, the CO conversion and C₅₊ selectivity in the presence of CO₂ decreased more significantly than in the absence of CO₂. CO₂ is found to be responsible for the partial oxidation of surface cobalt metal at FT synthesis environment with the co-existence of generated water.     

Performance of Pd catalysts supported on nanocrystalline α-Al2O3 and Ni-modified α-Al2O3 in selective hydrogenation of acetylene

Nanocrystalline α-Al₂O₃ and Ni-modified α-Al₂O₃ have been prepared by sol–gel and solvothermal methods and employed as supports for Pd catalysts. Regardless of the preparation method used, NiAl₂O₄ spinel was formed on the Ni-modified α-Al₂O₃ after calcination at 1150 °C. However, an addition of NiO peaks was also observed by X-ray diffraction for the solvothermal-made Ni-modified α-Al₂O₃ powder. Catalytic performances of the Pd catalysts supported on these nanocrystalline α-Al₂O₃ and Ni-modified α-Al₂O₃ in selective hydrogenation of acetylene were found to be superior to those of the commercial α-Al₂O₃ supported one. Ethylene selectivities were improved in the order: Pd/Ni-modified α-Al₂O₃–sol–gel > Pd/Ni-modified α-Al₂O₃-solvothermal ≈ Pd/α-Al₂O₃–sol–gel > Pd/α-Al₂O₃-solvothermal  Pd/α-Al₂O₃-commerical. As revealed by NH₃ temperature program desorption studies, incorporation of Ni atoms in α-Al₂O₃ resulted in a significant decrease of acid sites on the alumina supports. Moreover, XPS revealed a shift of Pd 3d binding energy for Pd catalyst supported on Ni-modified α-Al₂O₃–sol–gel where only NiAl₂O₄ was formed, suggesting that the electronic properties of Pd may be modified.     

Influence of Ru segregation on the activity of Ru–Co/γ-Al2O3 during FT synthesis: A comparison with that of Ru–Co/SiO2 catalysts

γ-Al₂O₃ and SiO₂ supported Co catalysts, with varying amounts of Ru, were prepared and evaluated for Fischer–Tropsch synthesis (FTS). The composition of Ru for optimum activity was found to be support-dependent. The reducible Co₃O₄ was high in the region of 0–1.64 wt.% of Ru in Co/SiO₂ catalysts. Co/γ-Al₂O₃ displayed a maximum for reducible Co species at 0.42 wt.% Ru. Segregation of Ru occurred beyond this composition decreasing the extent of reduction. Co/γ-Al₂O₃ catalysts showed lower activity and olefin selectivity, in spite of higher Co dispersion, than Co/SiO₂ catalysts. The catalytic performance depends on the amount of reducible Co species, which again depends upon the optimum content of Ru.     

Size effects on χ- to α-Al2O3 phase transformation

Nano-scaled χ-Al₂O₃ powders with d₅₀ mean particle sizes from 17 to 314 nm were prepared to investigate the size effect on their phase transformation. Structural properties and crystallization behavior as a function of thermal treatments of various-sized χ-Al₂O₃ particles were examined by DTA, XRD and TEM characterizations. It was confirmed that the decrease of particle size allows for stable α-Al₂O₃ formation at relatively low temperature. Furthermore, the phase transformation route of χ-Al₂O₃ to α-Al₂O₃ was also modified due to the decrease of particle size. A critical size of χ-Al₂O₃ that determines the phase transformation behavior was found to be around 40 nm. For particles larger than 40 nm, a transition phase of κ-Al₂O₃ is formed before obtaining final α-Al₂O₃ phase. Nevertheless, for those smaller than the critical size, starting χ-Al₂O₃ particles have to grow to 40 nm and then directly transform to α-Al₂O₃ bypassing κ-Al₂O₃ at a temperature as low as 1050 °C.     

Sintering kinetics of α-Al2O3 powder

The sintering kinetics of α-Al₂O₃ powder are reviewed in this paper. The initial sintering of α-Al₂O₃ micropowder and α-Al₂O₃ nanopowder is all controlled by grain boundary diffusion. The sintering kinetics dominate up to a relative density of 0.77, where the coarsening kinetics dominate during further densification. Herring's scaling law can be used to predict the approximate sintering temperature of α-Al₂O₃ powder and demonstrates that if the particle size can be reduced to <20 nm, sintering below 1000°C may be possible. ©     

Electrochemical micromachining using a solid electrochemical reaction at the metal/β″-Al2O3 microcontact

A simple solid state technique for electrochemical micromachining of metal substrates using a metal ion conductor (Na-β″-Al₂O₃) was proposed. The fundamental solid electrochemical cell consists of a (anode) metal substrate (M = Ag, Cu, Zn, and Pb)/pyramidal Na-β″-Al₂O₃/Ag (cathode) system, where the contact diameter between M/Na-β″-Al₂O₃ was extremely small, on the order of a few micrometer. Under an applied electric field, the metal substrate was electrochemically oxidized to metal ions (Mⁿ⁺) at the M/Na-β″-Al₂O₃ microcontact. These Mⁿ⁺ ions migrated into the Na-β″-Al₂O₃. As a result of continuous electrolysis, the metal substrate was locally consumed at the microcontact, and thus solid state electrochemical micromachining was accomplished. As expected, the machining size or depth depended on the electrolysis conditions (current, operating time) and the apex configuration of pyramidal Na-β″-Al₂O₃. Moreover, the scanning of the Na-β″-Al₂O₃ pyramid during electrolysis produced a fine patterned metal substrate. In the present paper, solid state electrochemical micromachining was performed for several metal substrates, and its advantages and disadvantages vis-a-vis the conventional electrochemical micromachining method are discussed in detail.     

Hydrodesulphurization performance of NiW/TiO2-Al2O3 catalyst for ultra clean diesel

TiO₂-Al₂O₃ binary oxide supports were obtained by sol–gel methods from Tetra-n-butyl-titanate and pseudoboehmite/aluminium chloride resources. The typical physico-chemical properties of NiW/TiO₂-Al₂O₃ catalysts with different TiO₂ loadings and their supports were characterized by means of BET, XRD and UV–vis DRS, etc. The BET results indicated that the specific surface areas of NiW/TiO₂-Al₂O₃ catalysts were as higher as that over pure γ-Al₂O₃ support, and the pore diameters were also large. The XRD and UV–vis DRS analyzing results showed that the Ti-containing supported catalysts existed as anatase TiO₂ species and the incorporation of TiO₂ could adjust the interaction between support and active metal, and impelled the higher reducibility of tungsten. The hydrodesulphurization (HDS) performance of the series catalysts were evaluated with diesel feedstock in a micro-reactor unit, and the HDS results showed that NiW/TiO₂-Al₂O₃ catalysts exhibited higher activities of ultra deep hydrodesulphurization of diesel oil than that of NiW/Al₂O₃ catalyst. The optimal TiO₂ content of NiW/TiO₂-Al₂O₃ catalysts was about 15 m%, and the corresponding HDS efficiency could reach to 100%. The sulphur contents of diesel products over NiW/TiO₂-Al₂O₃ (from pseudoboehmite/AlCl₃) catalysts with suitable TiO₂ content could be less than 15 ppmw, which met the sulphur regulation of Euro IV specification of ultra clean diesel fuel.     

The functionalities of Pt/γ-Al2O3 catalysts in simultaneous HDS and HDA reactions

A Pt/γ-Al₂O₃ catalyst was tested in simultaneous hydrodesulfurization (HDS) of dibenzothiophene and hydrodearomatization (HDA) of naphthalene reactions. Samples of it were subjected to different pretreatments: reduction, reduction–sulfidation, sulfidation with pure H₂S and non-activation. The reduced catalyst presented the best performance, even comparable to that of Co(Ni)Mo catalysts. All catalyst samples were selective to the HDS reaction over HDA, and to the direct desulfurization pathway of dibenzothiophene HDS over the hydrogenation reaction pathway of HDS. The effect of H₂S partial pressure on the functionalities of the reduced Pt/γ-Al₂O₃ catalyst was studied. The results showed that an increase in H₂S partial pressure does not cause poisoning, but an inhibition effect, without changing the catalyst selectivity. Accordingly, the activity trends were ascribed to adsorption differences between the different reactive molecules over the same catalytic active site. TPR characterization along with a thermodynamics analysis showed that the active phase of reduced Pt/γ-Al₂O₃ is constituted by Pt⁰ particles. However, presulfidation of the catalyst leads to a mixture of PtS and Pt⁰ which has a negative effect on the catalytic performance without changing catalyst functionalities.     

Mechanism and kinetics of Al2O3 nanoparticles formation by reaction of bulk Al with H2O and CO2 at sub- and supercritical conditions

Oxidation of bulk samples of 〈Al〉 by water and H₂O/CO₂ mixture at sub- and supercritical conditions for uniform temperature increase and at the injection of H₂O (665 K, 23.1 MPa) and H₂O/CO₂ (723 K, 38.0 MPa) fluids into the reactor has been studied. Transition of 〈Al〉 into AlOOH and Al₂O₃ nanoparticles has been found out. Aluminum samples oxidized by H₂O and H₂O/CO₂ fluids at the injection mostly consist of large particles (300-500 nm) of α-Al₂O₃. Those oxidized for uniform temperature increase contain smaller particles (20-70 nm) of γ-Al₂O₃ as well. Mechanism of this phenomenon is explained by orientation of oxygen in H₂O polar molecules to the metal in the electric field of contact voltage at Al/AlOOH and Al/Al₂O₃ boundary. Addition of CO₂ to water resulted in CO, CH₄, CH₃OH and condensed carbon, increase in size of Al₂O₃ nanoparticles and significant decrease in time delay. In pure CO₂ 〈Al〉 oxidation resulted in oxide film. Using temperature and time dependences of gaseous reactant pressure and Redlich-Kwong state equation, kinetics of H₂ formation has been described and oxidation regularities determined. At aluminum oxidation by H₂O and H₂O/CO₂ fluids, self-heating of the samples followed by oxidation rate increase has been registered. The samples of oxidized aluminum have been studied with a transmission electronic microscope, a thermal analyzer and a device for specific surface measurement. The effect of oxidation conditions on the characteristics of synthesized nanoparticles has been found out.     

Effects of the preparation methods on the performance of the Cu–Cr–Fe/γ-Al2O3 catalysts for the synthesis of 2-methylpiperazine

Co-precipitation, impregnation and ultrasonic sol–gel (USG) methods have been used to prepare Cu–Cr–Fe/γ-Al₂O₃ catalysts, which were further used to synthesize 2-methylpiperazine. The catalysts were characterized by XRD, XPS, TG/DSC, BET, TPR, AAS and TEM. It is found that preparation method can greatly impact the catalytic performance of the catalysts, the Cu–Cr–Fe/γ-Al₂O₃ catalyst prepared by the ultrasonic sol–gel method proved to be the most active and stable for this reaction. The dispersion and stabilization of Cu⁰ in the reduced catalysts are attributed to the existence of CuCr₂O₄ and Fe₂O₃. A surprising copper migration was detected by XPS analysis for the Cu–Cr–Fe/γ-Al₂O₃-USG catalyst after the calcination process, which may be crucial to the high activity and stability of this catalyst.     

Influence of the oxygen pretreatment on the CO2 reforming of methane on Ni/β-SiC catalyst

The influence of the O₂ pretreatment on the CO₂ reforming of methane to synthesis gas has been investigated with Ni catalysts supported on β-SiC extrudate. The structure and properties of the catalysts were characterised by SEM, TEM and XRD techniques. The pretreatment of the catalyst by a mixture of CO₂ and O₂ significantly improves the catalytic activity for the CO₂ reforming. On the Ni 5 wt.% supported on β-SiC catalyst, the CH₄ conversion has reached 90% with the O₂ pretreatment instead of 80% by direct activation under CO₂/CH₄ mixture. The oxygen pretreatment seems to stabilize the metallic nickel phase instead of NiSi₂.     

Effect of SO2 on the catalytic activity of Ga2O3–Al2O3 for the selective reduction of NO with propene in the presence of oxygen

The effect of coexisting SO₂ on the catalytic activity of Ga₂O₃–Al₂O₃ prepared by impregnation, coprecipitation and sol–gel method for NO reduction by propene in the presence of oxygen was studied. Although the activity of Al₂O₃ and Ga₂O₃–Al₂O₃ prepared by impregnation (Ga₂O₃/Al₂O₃(I)) and coprecipitation (Ga₂O₃–Al₂O₃(CP)) was depressed considerably by the presence of SO₂, NO conversion on Ga₂O₃–Al₂O₃ prepared by sol–gel method (Ga₂O₃–Al₂O₃(S)) was not decreased but increased slightly by SO₂ at temperatures below 723 K. From catalyst characterization, SO₂ treatment was found to cause two important effects on the surface properties: one is the creation of Brønsted acid sites on which propene activation is promoted (positive effect), and the other is the poisoning of NO_x adsorption sites on which NO reduction proceeds (negative effect). It was presumed that the influence of SO₂ treatment on the catalytic activity is strongly related to the balance between the negative and positive. The activity enhancement of Ga₂O₃–Al₂O₃(S) by SO₂ was accounted for by the following consideration: (1) increase of the propene activation ability by SO₂, (2) incomplete inhibition of NO_x adsorption sites by SO₂.     

Reduction of NO by CO on Cu/ZrO2/Al2O3 catalysts: Characterization and catalytic activities

ZrO₂, γ-Al₂O₃ and ZrO₂/γ-Al₂O₃-supported copper catalysts have been prepared, each with three different copper loads (1, 2 and 5 wt%), by the impregnation method. The catalysts were characterized by nitrogen adsorption (BET), X-ray diffraction (XRD), temperature programmed reduction (TPR) with H₂, Raman spectroscopy and electronic paramagnetic resonance (EPR). The reduction of NO by CO was studied in a fixed-bed reactor packed with these catalysts and fed with a mixture of 1% CO and 1% NO in helium. The catalyst with 5 wt% copper supported on the ZrO₂/γ-Al₂O₃ matrix achieved 80% reduction of NO. Approximately the same rate of conversion was obtained on the catalyst with 2 wt% copper on ZrO₂. Characterization of these catalysts indicated that the active copper species for the reduction of NO are those in direct contact with the oxygen vacancies found in ZrO₂.     

Molten salt synthesis of α-Al2O3 platelets using NaAlO2 as raw material

α-Al₂O₃ platelets were prepared by a molten salt synthesis method when NaAlO₂ was used as raw material. The effects of the stirring rate during the gel preparation, heating temperature, type and addition amount of molten salts, addition of plate-like α-Al₂O₃ seeds, additives such as TiOSO₄ and Na₃PO₄·12H₂O on the morphology of α-Al₂O₃ were studied. High stirring rate during the gel preparation and high heating temperature not only help to restrain the overlapping of α-Al₂O₃ platelets, but also improve the size distribution. When the heating temperature increases to 1200 °C, most of α-Al₂O₃ platelets are hexagonal in its morphology, and the size of platelets becomes relatively uniform. When Na₂SO₄-K₂SO₄ flux is used instead of NaCl-KCl flux, it is easy to obtain α-Al₂O₃ platelets with a big size. When the molar ratio of salt to final Al₂O₃ powders increases to 4:1, most of α-Al₂O₃ platelets are hexagonal, and the overlapping of powders is inhibited. The addition of a small amount of plate-like seeds has a significant effect on the size of α-Al₂O₃ platelets. With the increase of seed amount, the diameter of α-Al₂O₃ platelets tends to decrease. The addition of 5.45 wt.% TiOSO₄ results in the formation of hexagonal α-Al₂O₃ platelets with an average diameter of 5.1 μm and an average thickness of 1.4 μm. Thin α-Al₂O₃ platelets with a discal shape are obtained owing to the co-addition of 0.51 wt.% Na₃PO₄·12H₂O and 3 wt.% TiOSO₄.     

Growth mechanism of single-crystal α-Al2O3 nanofibers fabricated by electrospinning techniques

Crystal-growth-related microstructures and the length-to-diameter ratio of a single-crystal-type α-Al₂O₃ nanofiber were examined using HR-TEM techniques. The fibers exhibited diameters ranging from 50 to 100 nm and lengths of several tens of micrometers. During thermal treatments, the alumina fiber went through phase transformations similar to boehmite. Therefore, the phase evolution, especially the final θ- to α-Al₂O₃ stage of the phase transformation, may be the determining factor in the microstructural evolution of the nanofibers. HR-TEM techniques were utilized to demonstrate that the single crystals were formed by the coalescence of well-elongated α-Al₂O₃ colonies. The fibers grew in the [1 1 0] or [1 1 2] direction instead of [0 0 1]. A thermodynamic analysis revealed that if the α-Al₂O₃ nanofiber that transformed from θ-Al₂O₃ behaved in a stable manner, there could be a size ratio limit for the length and diameter of each α-Al₂O₃ colony. The smallest potential diameter was calculated to be around 17 nm.     

NiO/Al2O3 oxygen carriers for chemical-looping combustion prepared by impregnation and deposition-precipitation methods

Ni-based oxygen carriers (OC) with different NiO content were prepared by incipient wet impregnation, at ambient (AI), and hot conditions (HI) and by deposition-precipitation (DP) methods using γ-Al₂O₃ and α-Al₂O₃ as supports. The OC were characterized by BET, Hg porosimetry, mechanical strength, TPR, XRD and SEM/EDX techniques. Reactivity of the OC was measured in a thermogravimetric analyzer and methane combustion selectivity towards CO₂ and H₂O, attrition rate, and agglomeration behavior were analyzed in a batch fluidized bed reactor during multicycle reduction-oxidation tests.XRD and TPR analysis showed the presence of both free NiO and NiAl₂O₄ phases in most of the OC. The interaction of the NiO with the alumina during OC preparation formed NiAl₂O₄ that affected negatively to the OC reactivity and methane combustion selectivity towards CO₂ and H₂O during the reduction reaction. The NiO-alumina interaction was more affected by the support type than by the preparation method used. The NiO-alumina interaction was stronger in the OC prepared on γ-Al₂O₃.The OC were evaluated in the fluidized bed reactor with respect to the agglomeration process. OC prepared by the AI and HI methods with NiO contents up to 25 wt%, OC prepared by the DP method on γ-Al₂O₃ with NiO content lower than 30 wt%, and OC prepared by the DP method on α-Al₂O₃ with a NiO content lower than 26 wt% did not agglomerated. OC that agglomerated showed an external layer of NiO over the particles. It seems that the most important factor affecting to the formation of the external NiO layer on the OC, and so to the agglomeration process, was the metal content of the OC. The attrition rates of the OC prepared using γ-Al₂O₃ as support were higher than the ones prepared using α-Al₂O₃ as support, and in general the attrition rates of all the OC were low.The OC prepared by AI, HI or DP methods on α-Al₂O₃ as support had appropriated characteristics to be used in the chemical-looping combustion process.     

Hydrogen production by steam reforming of LNG over Ni/Al2O3-ZrO2 catalysts: Effect of ZrO2 and preparation method of Al2O3-ZrO2

An Al₂O₃-ZrO₂ support was prepared by grafting a zirconium precursor onto the surface of commercial γ-Al₂O₃. A physical mixture of Al₂O₃-ZrO₂ was also prepared for the purpose of comparison. Ni/Al₂O₃-ZrO₂ catalysts were then prepared by an impregnation method, and were applied to the hydrogen production by steam reforming of liquefied natural gas (LNG). The effect ZrO₂ and preparation method of Al₂O₃-ZrO₂ on the performance of supported nickel catalysts in the steam reforming of LNG was investigated. The Al₂O₃-ZrO₂ prepared by a grafting method was more efficient as a support for nickel catalyst than the physical mixture of Al₂O₃-ZrO₂ in the hydrogen production by steam reforming of LNG. The well-developed tetragonal phase of ZrO₂ and the high dispersion of ZrO₂ on the surface of γ-Al₂O₃ were responsible for the enhanced catalytic performance of Ni/Al₂O₃-ZrO₂ prepared by way of a grafting method.     

The effect of sodium on the catalytic activity of ZnO–Al2O3/ZSM-5 and SnO–Al2O3/ZSM-5 for the transesterification of vegetable oil with methanol

In order to elucidate the effect of sodium on the activity of ZSM-5 supported metal oxides catalysts (ZnO–Al₂O₃/ZSM-5 and SnO–Al₂O₃/ZSM-5) for the transesterification of soybean oil with methanol, ZSM-5 supported metal oxides were prepared with and without sodium hydroxide by impregnation. The metal compositions of the ZSM-5 supported metal oxide catalysts and the metal concentrations dissolved from the catalysts to the methylester phase were measured by SEM-EDS and inductive coupled plasma spectroscopy, respectively. The catalytic activity of ZnO–Al₂O₃/ZSM-5 and SnO–Al₂O₃/ZSM-5 containing sodium did not originate from surface metal oxides sites, but from surface sodium sites or dissolved sodium leached from the catalyst surface.     

Effect of the reducing agent on the hydrodechlorination of dioxins over 2 wt.% Pd/γ-Al2O3

2-Propanol and molecular H₂ (in methanol (MeOH) and MeOH–water) were examined as reducing agents for the liquid phase hydrodechlorination (HDC) of dioxins over 2 wt.% Pd/γ-Al₂O₃. Different amounts of NaOH were added to the reaction mixtures. The 2-propanol and H₂(g)/MeOH systems presented similar HDC activity. Notwithstanding, Pd sintering and graphitic carbon directly bonded to Pd on catalyst surface was observed on samples used with H₂(g)/MeOH. The addition of water to H₂(g)/MeOH decreased Pd sintering and favored dissolution of sodium compounds. However, dioxin degradation efficiency diminished. By contrast, 2-propanol acting both as reducing agent and solvent provided hydrogen to the HDC reaction, avoided metal sintering and Pd–C formation. Besides, almost complete dioxin degradation under mild reaction conditions was obtained. Kinetic experiments of dioxin HDC with 2-propanol showed a maximum net reaction rate and turnover frequency (TOF) for a given initial concentration of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs). After that value, both reaction rate and TOF decreased. On the other hand, reaction rates and TOFs of dioxin-like polychlorinated biphenyls (DL-PCBs) linearly increased with concentration.     

Improvement of coke resistance of Ni/Al2O3 catalyst in CH4/CO2 reforming by ZrO2 addition

This work investigates the improvement of Ni/Al₂O₃ catalyst stability by ZrO₂ addition for H₂ gas production from CH₄/CO₂ reforming reactions. The initial effect of Ni addition was followed by the effect of increasing operating temperature to 500–700 °C as well as the effect of ZrO₂ loading and the promoted catalyst preparation methods by using a feed gas mixture at a CH₄:CO₂ ratio of 1:1.25. The experimental results showed that a high reaction temperature of 700 °C was favored by an endothermic dry reforming reaction. In this reaction the deactivation of Ni/Al₂O₃ was mainly due to coke deposition. This deactivation was evidently inhibited by ZrO₂, as it enhances dissociation of CO₂ forming oxygen intermediates near the contact between ZrO₂ and nickel where the deposited coke is gasified afterwards. The texture of the catalyst or BET surface area was affected by the catalyst preparation method. The change of the catalyst texture resulted from the formation of ZrO₂–Al₂O₃ composite and the plugging of Al₂O₃ pore by ZrO₂. The 15% Ni/10% ZrO₂/Al₂O₃ co-impregnated catalyst showed a higher BET surface area and catalytic activity than the sequentially impregnated catalyst whereas coke inhibition capability of the promoted catalysts prepared by either method was comparable. Further study on long-term catalyst stability should be made.