固体装载率对局部相含率与液体速率的影响

在高径比(H/D=22.2)的气升式内环流反应器中,以空气-水-石英砂为物系,研究了固体装载率和表观气速对导流筒内局部固含率、下降区固含率、下降区液体速率的影响,以及导流筒内局部气含率、固含率随轴向高度的分布规律。结果表明,固体体积分数小于或等于1.0%时,导流筒内局部固含率和下降区固含率与表观气速无关;下降区液体速率随表观气速和固体装载率的增加而下降;固定表观气速,在固体体积分数小于或等于2.0%时,导流筒内气含率在轴向是均匀分布的。     

Liquid velocity in a high‐solids‐loading three‐phase external‐loop airlift reactor

BACKGROUND: Airlift reactors are of interest for many different processes, especially for three‐phase systems. In this study the behavior of a high‐loading three‐phase external‐loop airlift reactor was examined. In particular, the effect of parameters such as airflow rate (riser superficial gas velocities between 0.003 and 0.017 m s^?1), solids loading (up to 50%, v/v) on liquid circulation velocity in the air‐water‐alginate beads system as a crucial hydrodynamic parameter was studied. RESULTS: It was observed that increase of the airflow rate resulted in increase of the liquid velocity in the system. The same result but less pronounced was observed by introducing small amounts of solid particles up to 7.5% v/v. However, further introduction of solids caused decrease of the liquid velocity. Laminar regime for the liquid circulation was observed for low gas velocities. Minimum gas velocities for recirculation initiation in the reactor were determined for all solid loadings and linear dependence on the solid content was found. Gas holdups for the three‐phase system were larger than for the two‐phase system in all experiments. A simple model for predicting the liquid circulation velocity in the three‐phase system with high solid loading of low‐density particles was developed. This model is based on the viscosity of integrated medium (solid + liquid) which is a new aspect to analyze this phenomenon. CONCLUSIONS: The developed model shows very good agreement with the experimental results for all solid loadings. It also includes the influence of reactor geometry on the liquid circulation velocity thus enabling optimization. Copyright © 2012 Society of Chemical Industry     

三相环流反应器中的局部相含率

将压差法与气-液相间滑移速度相结合,提出了利用压差法测量三相区局部相含率的新方法,将测得的局部固含率进行轴向平均并与由颗粒装填量计算所得的固含率进行比较,证明了此方法的可靠性. 利用所提出的测量方法,考察了三相环流反应器中气含率和固含率随操作条件的变化规律. 结果表明,气含率随表观气速的升高而增大,且随轴向位置的升高而增大;大颗粒具有破碎气泡的作用,能够增大反应器内的气含率;固含率随表观气速的增加而降低,且沿轴向变化较大. 表观气速较高时,固含率沿轴向近似呈S形分布.     

Oxygen transfer and hydrodynamics in three-phase inverse fluidized beds

Experiments were performed at ambient temperature and pressure in a 152 mm inner diameter column with air, tap water or 0.5% wt. aqueous ethanol solution, and polypropylene particles. An increase in liquid velocity and solids loading, and the presence of a surfactant reduces the gas velocity required to reach full bed expansion, which is delimited by the gas sparger. With an increase in gas velocity, solids holdups remain constant after full bed expansion, liquid holdups increase to a maximum and then decrease and gas holdups continuously increase. The addition of ethanol greatly increases the gas holdups leading to significant reductions in liquid holdups. The volumetric gas-liquid mass transfer coefficient, k_La, increases with increasing gas velocity but does not change significantly with liquid velocity. There are complex interaction effects between solids loading and surfactants as the values of k_La in the aqueous ethanol solution were greater than those in water when particles were present and smaller without particles. k_La data in water were found to be proportional to gas holdup whereas for the ethanol solution this proportionality constant first decreased with increasing gas velocity to eventually stabilize at a value smaller than for water.     

Local hydrodynamics modeling of a gas–liquid–solid three-phase bubble column

A three-dimensional (3D) transient model was developed to simulate the local hydrodynamics of a gas–liquid–solid three-phase bubble column using the computational fluid dynamic method, where the multiple size group model was adopted to determine the size distribution of the gas bubbles. Model simulation results, such as the local time-averaged gas holdups and axial liquid velocities, were validated by experimental measurements under varied operating conditions, e.g., superficial gas velocities and initial solid loadings at different locations in the three-phase bubble column. Furthermore, the local transient hydrodynamic characteristics, such as gas holdups, liquid velocities, and solid holdups, as well as gas bubble size distribution were predicted reasonably by the developed model for the dynamic behaviors of the three-phase bubble column. © 2007 American Institute of Chemical Engineers AIChE J, 2007     

Measurement of Local Phase Holdups in a Two‐ and Three‐Phase Bubble Column

A new invasive sensing probe for the measurement of local phase holdups in two‐ and three‐phase reactors is described. The local gas and solids holdups in a bubble column with a volume of V = 2 m³ at varying operating conditions (gas velocity, sparger design, solids content and density) are measured by means of differential pressure measurement in combination with either time domain reflectometry or electrical conductivity measurement. The phase distribution profiles at two‐ and three‐phase operating conditions are described. The influence of the sparger design on the shape of these profiles, the influence of the solid phase on the gas distribution, the solids distribution and the gas‐stow effect above the sparger because of a dense particle layer are capable of experimental proof for the first time.     

气-液-固三相循环流化床中的液相轴向扩散

The effects of liquid viscosities, solid circulating rates, liquid and gas velocities and phase holdups on the axial dispersion coefficient, Dax, were investigated in a gas-liquid-solid circulating fluidized bed (GLSCFB).Liquid viscosity promotes the axial liquid backmixing when solid particles and gas bubbles are present. Increases in gas velocities and solid circulating rates lead to higher Dax. The effects of liquid velocity on Dax are associated with liquid viscosity. Compared with conventional expanded beds, the GLSCFBs hold less axial liquid dispersion,approaching ideal plug-flow reactors.     

Experimental analysis and development of correlations for gas holdup in high pressure slurry co-current bubble columns

The effect of liquid and gas velocities, solid concentrations, and operating pressure has been studied experimentally in a 15 cm diameter air-water-glass beads bubble column. The superficial gas and liquid velocities varied from 1.0 to 40.00 cm/s and 0 to 16.04 cm/s, respectively, while the solid loading varied from 1 to 9%. The gas holdup in the column was reduced sharply as we switched from batch to co-current mode of operation. At low gas velocity, the effect of liquid velocity was insignificant; while at high gas velocity, increasing liquid velocity decreased the gas holdup. Drift flux approach was applied to quantify the combined effect of liquid and gas velocities over gas holdup. For co-current three phase flows, the gas holdup decreased with increase in solid loading for all pressures. But for batch operations, when solid loading was 5% or more, settling started leading to higher gas holdup. Increasing pressure from atmospheric conditions increased the gas holdup significantly, flattening asymptotically.     

Effects of sparger height and orifice orientation on solids dispersion in a slurry bubble column

The effects of gas distributor height and the orientation of its orifices are investigated on solids dispersion and gas holdup profiles in a three-phase slurry bubble column. The height of the distributor was varied to cover locations from near column bottom to above the settled solids bed height. The orifice orientations were changed from upward facing to downwards facing directions. The measurements were conducted in a Plexiglas column of 0.15 m ID and 2.5 m height. The gas phase was oil-free compressed air while tap water was used as liquid phase. Glass beads with an average particle diameter of 35 μm and density of 2450 kg/m³ constituted the solid phase. The settled bed height was about 0.4 m which provided an average slurry concentration of about 15% (v/v) when all solids were dispersed. Both axial and column average phase holdups were measured. Effects of sparger location, gas jets formation and liquid circulation patterns on gas holdups and solids dispersion are analyzed. Empirical correlations are developed to relate sparger location to solids dispersion as a function of gas velocity. Optimum sparger height and orifice orientation is proposed based on the measurement of this study.     

Local measurements for the study of external loop airlift hydrodynamics

Hot-film anemometry and an optical biprobe are used to measure local flow characteristics in the riser of an external loop airlift reactor. Important flow asymmetries are observed above the sparger and developing flow persists through a large part of the riser. As gas flow rate increases, radial gas hold-up profiles change from relatively flat to parabolic while the shape of radial liquid velocity profiles remains constant and Sauter bubble diameter increases. At large gas superficial velocities, slip velocity is found to deviate considerably from the frequently used value of 0.25 m/s. Local measurements allow a better understanding of two-phase flow in airlift reactors and can be used for CFD-modeling development and validation.     

Gas holdup and bubble dynamics in a three-phase internal loop reactor with external slurry circulation

As modified three-phase fluidized reactors, loop reactors have been widely used in the area of chemical and energy processes. An external slurry circulation is introduced into a traditional internal loop reactor to improve the transfer between gas and slurry phases. Gas holdup and bubble dynamics are investigated by using the double-sensor conductivity probe technique in the present work. The results show that gas holdup inside the draft tube is greatly affected by the geometrical configuration and is much higher than that in the corresponding section of the annular region. Local, section-averaged, and overall gas holdups increase with increasing superficial gas velocity, while the effects of solid loading and external slurry circulation velocity are less significant than that of superficial gas velocity. Both local bubble size and bubble rise velocity vary significantly in different regions.     

EFFECTS OF GEOMETRY ON HYDRODYNAMICS IN EXTERNAL-LOOP AIRLIFT REACTORS

Experimental investigations were carried out in model external-loop airlift reactors. Two reactors of laboratory scale (riser liquid height ranged between 1.16-1.56 m, riser diameter 0.03 m, A_D/A_R ratio between 0.111-1,000, total liquid volume V_T = (1.189-2.446).10^-3m³) and pilot-plant scale (riser liquid height of 4.4 and 4.7 m, respectively, riser diameter 0.200 m, A_D/A_R ratio of 0.1225 and 0.040 m, total liquid volume, V_T = (0.144-0.170) m³) were used.

The influences of reactor geometry characterized by some parameter as: A_D/A_R ratio, liquid height in riser and downcomer and liquid height in gas separator, together with the amount of introduced air, on the basic hydrodynamic design parameters: gas holdup and liquid circulation velocity were analysed.

The influence of gas sparger design on gas holdup and liquid velocity was found to be negligible.

The experimental liquid circulation velocity was correlated using a simplified form of the energy balance in airlift reactors, valid for external-loop airlift reactors with almost complete phase separation at the top.

An original dimensionless correlation for gas holdup prediction involving superficial velocities of gas and liquid, cross sectional areas, dispersion height, riser diameter, as well as Froude number, was obtained.     

两级气液内环流反应器内气含率和循环液速

基于多釜串联可以有效减小返混的原理,通过引入特殊设计的级间构件构建了一种新型的两级内环流反应器。实验研究了级间构件形式、表观气速、表观液速和气液分离器对每一级内气含率和循环液速的影响。实验结果表明,表观气速对反应器二级(上一级)中上升管与下降管气含率之差和循环液速影响较大,而对一级(下一级)的影响较小;各级内上升管和下降管的气含率均随表观液速的增大而减小,但影响程度较小。基于推动力和阻力平衡建立了预测反应器中每一级的气含率和循环液速的流体力学模型,模型预测值与实验结果吻合较好。     

高长径比环流反应器中气、固含率的轴向分布研究

在高长径比(H/D=22.2)内环流反应器中,常温常压下,以空气-水-石英砂为物系,研究了表观气速和固体装载量对平均气含率、下降区气含率、上升区固含率、下降区固含率的影响,以及上升区气含率、固含率随轴向高度的分布规律.结果表明:平均气含率、下降区气含率随着表观气速的增加而增加,随ω(固体)增大而下降,ω(固体)≤2.6...     

气液固三相外环流反应器相含率分布与气液流动结构

结合电阻层析成像和差压法,以粒径3 mm的聚氨酯(密度1110 kg/m3)和粒径0.5, 1, 3 mm的玻璃珠(密度2460 kg/m3)为固相、空气为气相、水为液相,在直径0.09 m、高3.1 m的气液固三相气升式外环流反应器中考察了固相颗粒密度、粒径、固相含率对上升管和下降管中气含率的影响. 结果表明,当玻璃珠粒径为0.5和1 mm、表观气速ug>0.10 m/s时环流反应器可达到充分发展段. 以玻璃珠为固相时,气含率随固相含量和粒径增大而增大,从层析图像可见,在r/R=0~0.2处出现非导电相的极大值,且加入大颗粒的下降管中气固含率明显大于加入小颗粒的. 根据电阻层析成像的虚拟像,给出了时间序列的气固混合相的流动特征.     

Circulation liquid velocity,gas holdup and volumetric oxygen transfer coefficient in external-loop airlift reactors

The effects of the horizontal connection length (0.1 ± L_e ± 0.5 m), the cross-sectional area ratio of downcomer-to-riser (0.11 ± A_d/A_r± 0.53), and the superficial gas velocity on gas phase holdups in the riser and downcomer were studied. The circulation liquid velocity, the mixing performance and the volumetric mass transfer coefficient in the external-loop airlift reactors were also measured. The horizontal connection length and A_d/A_r were major parameters which strongly affected the performance of external-loop airlift reactors. Useful correlations in the external-loop airlift reactors were obtained for gas holdups, the volumetric mass transfer coefficient, the circulation liquid velocity, and the mixing time.     

Three‐phase airlift internal loop reactor: correlations for predicting the main fluid dynamic parameters

Three‐phase airlift loop reactors have many industrial applications. Examples include applications in the chemical, metallurgical, biochemical and minerals‐processing industries; fluid dynamics in such systems is a critical factor affecting efficiency. The experimental work was carried out at a pilot‐plant scale in a tank with a cylindrical shape and conical bottom (height 1.25 m; diameter 0.42 m), water and air were used as liquid and gas phases, and for different solid phases, different loads of glass spheres (diameters: 0.25 and 1 mm; density 2.6 g cm^?3), and polystyrene cylinders (diameter and length 3 mm; density 1.0 g cm^?3) were introduced. Air was injected through the bottom of the tank by means of 12 nozzles (diameter 1 mm each). An internal draft tube riser was tested on different configurations as its diameter was varied (44, 82, 125 and 240 mm) as was its height (1050 and 630 mm). Corresponding liquid velocities in the adjacent annular downcomer were determined by a thermal tracer technique, solid holdups were determined by conductivity methods, riser overall gas holdups were deduced from the liquid level, and riser gas holdup from manometer readings. Several adjusted correlations were considered in a method to predict the main fluid dynamic parameters (solids and gas holdups, and superficial liquid velocities). Copyright © 2005 Society of Chemical Industry     

Structure of trickle-to-pulse flow regime transition and pulse dynamics at elevated temperature in slow-mode cyclic operation

The effects of temperature and pressure on the structure of the trickle-to-pulse flow regime transition in slow-mode cyclic operation in trickle-bed reactors were reported. The relationship between liquid holdup and liquid velocities at the trickle-to-pulse flow transition in cyclic operation, the shock wave behavior as a function of bed depth, as well as the pulsing flow regime properties were investigated for Newtonian (air-water) and non-Newtonian (air-0.25% carboxymethylcellulose (CMC)) liquids. At a given temperature, the breakthrough, plateau and decay times of the shock wave were found to decrease with bed depth. The pulse velocity and pulse frequency for pulsing flow regime both in cyclic operation and in natural pulsing (constant-throughput operation) were observed to increase with temperature. However, increasing the reactor pressure led to increased pulse frequency and decreased pulse velocity. Analysis of the transition liquid holdups for natural pulse flow and cyclic operation revealed that the liquid holdup decreased with temperature and pressure. The transition liquid holdups and superficial liquid pulse velocities in symmetric peak-base cyclic operation surpassed those in constant-throughput operation for given temperature, pressure and gas velocity, giving rise to wider trickle flow regime area in cyclic operation. The behavior of both Newtonian and power-law non-Newtonian fluids was similar regarding the effect of temperature, pressure and gas velocity.     

Measuring techniques in gas-liquid and gas-liquid-solid reactors

This article offers an overview of the instrumentation techniques developed for multiphase flow analysis either in gas/liquid or in gas/liquid/solid reactors. To characterise properly such reactors, experimental data have to be acquired at different space scale or time frequency. The existing multiphase flow metering techniques described give information concerning reactor hydrodynamics such as pressure, phases holdups, phases velocities, flow regime, size and shape of dispersed inclusions, axial diffusion coefficients. The measuring techniques are presented in two groups: the non-intrusive techniques that deliver global, cross-section-averaged or local data, and the intrusive probes that are dedicated to local measurements. Eventually some examples of multiphase instrumentation development are reported (trickle-bed and slurry bubble column at semi-industrial scale) in the refinery or petrochemical area.     

Heat transfer and bubble dynamics in a three-phase inverse fluidized bed

In this study, surface-to-bed heat transfer experiments were performed to gain insight on heat transfer and hydrodynamics in a three-phase inverse fluidized bed. Air, tap water or 0.5 wt.% aqueous ethanol, and polypropylene were, respectively, the gas, liquid and solid phases. The solid loading was varied from 0 to 30 vol.%, and the gas and liquid superficial velocities from 2 to 50 mm/s and 0 to 21 mm/s, respectively. Visual observations were associated with measured phase holdups and instantaneous heat transfer coefficients. Larger gas velocities lead to an increase in bubble size due to the transition to the coalesced bubble flow regime. The greater turbulence induced by the larger bubbles increases the average heat transfer coefficient. On the other hand, adding ethanol reduces the heat transfer coefficient. Solid concentrations up to ∼13 vol.% increase the average heat transfer coefficient whereas higher solid concentrations tend to lower it. The distribution of instantaneous heat transfer coefficient peak height is wider at higher gas and liquid velocities while the addition of a surfactant narrows it. Gas holdups and average heat transfer coefficients are both compared with existing correlations, which are then adjusted for a better fit.