EPR and DRS evidence for NO2 sensing in Al-doped ZnO

Zinc oxide (ZnO) is a well-known semiconducting multifunctional material wherein properties right from the morphology to gas sensitivity can be tailor-made by doping or surface modification. Aluminum (Al)-incorporated porous zinc oxide (Al:ZnO) exhibits good response towards NO₂ at low-operating temperature. The NO₂ gas concentration as low as 20 ppm exhibits S = 17% for 5 wt.% Al-incorporated ZnO. The NO₂ response increases with operating temperature and concentration and reaches to its maximum at 300 °C without any interference from other gases such as SO₃, HCl, LPG and alcohol. Physico-chemical characterization likes differential thermogravimetric analysis (TG-DTA) electron paramagnetic resonance (EPR) and diffused reflectance spectroscopy (DRS) have been used to understand the sensing behavior for pure and Al-incorporated ZnO. The TG-DTA depicts formation of ZnO phase at 287 °C. The EPR study reveals distinct variation for O⁻ (g = 2.003) and Zn interstitial (g = 1.98) defect sites in pure and Al:ZnO. The DRS studies elucidate signature of adsorbed NO_x species in aluminium-incorporated zinc oxide indicating its tendency to adsorb these species even at low temperatures. This paper is an attempt to correlate the gas sensing behavior with the physico-chemical studies such as EPR and DRS.     

White organic light-emitting devices with non-doped-type structure

A non-doped-type structure was proposed for obtaining organic light-emitting devices with high-efficiency and full-spectrum white light emission. The device structure included indium tin oxide glass substrate/450 Å 4,4′,4″-tris{N-(3-methylphenyl)-N-phenylamin}triphenylamine (m-MTDATA) hole injection layer/100 Å N,N′-bis-(1-naphthyl)-N,N′-diphenyl-1,1′-biph-enyl-4,4′-diamine (NPB) hole transport layer/150 Å 4,4′-bis(2,2′-diphenylvinyl)-1,1′-biphenyl (DPVBi) blue emitting layer/ultrathin [2-methyl-6-[2-(2,3,6,7-tetrahydro-1H, 5H-benzo[ij] quinolizin-9-yl)ethenyl]-4H-pyran-4-ylidene] propane-dinitrile (DCM2) yellow-emitting layer/ 80 Å 4,7-diphenyl-1,10-phenanthroline (BPhen) electron transporting layer and hole blocking layer/600 Å tris (8-hydroxyquinoline) aluminium (Alq3) electron-transporting layer /10 Å lithium fluoride (LiF)/aluminum (Al). A white emission (Commission Internationale de l’Eclairage 1931 chromaticity coordinate) (X = 0.3556, Y = 0.3117) at 5 V and (X = 0.282, Y = 0.2658) at 15 V was obtained. Its luminance was 11,497 cd/m² at 15 V, and the maximum efficiency was 4.8 lm/W at 5 V.     

Fabrication and characterization of low temperature sintering PMN–PZN–PZT step-down multilayer piezoelectric transformer

For the fabrication as step-down multilayer piezoelectric transformer, piezoelectric properties of Pb(Mg_1/3Nb_2/3)O₃–Pb(Zn_1/3Nb_2/3)O₃–Pb(Zr_0.52Ti_0.48)O₃ (PMN–PZN–PZT) ceramics were optimized by ZnO–Li₂CO₃ (ZL) and Pb₃O₄ content. Effects of the additions on the structure, bulk density and electrical properties of ceramics were investigated. The results revealed that the proper additions of ZL with Pb₃O₄ content could modify the electrical properties of the PMN–PZN–PZT ceramics. The composition sintered at 995 °C with 0. 01 wt.% ZL and 0.10 wt.% Pb₃O₄ content showed higher values, which were listed as follows: d₃₃ = 256 pC/N, K_p = 0.60, Q_m = 1910, _r = 1032, tan δ = 0.0070 and r = 2.09 Ω. In addition, the step-down piezoelectric transformers with optimized PMN–PZN–PZT composites were fabricated and the characteristics as the output power and resistance loads were measured. Meanwhile, the step-down piezoelectric transformers sintered at 995 °C showed the favorable characteristics with a higher gain G of 0.204 and a lower temperature rise of 6 °C when the output power was 5 W, and the driving frequency were approximately constant (≈126 kHz) when the output power was from 5 to 13 W. Moreover, the maximum efficiency (90.2%) was obtained at load resistance of 10 Ω.     

Characterization of transition metal oxide ceramic material for continuous thermocouple and its use as NTC fire wire sensor

The ceramic powder prepared from the mixture of Mn₃O₄ and La₂O₃ have been characterized for NTC behavior and the same have been used as CT²C (continuous thermocouple) sensor in the form of a thin metal cable to detect over-heating. These materials have mega ohm resistance at room temperature and showed exponential drop in resistance with the rise in temperature over a temperature range of 100–400 °C. It has been observed that as the concentration of La₂O₃ increases from 0 to 10% the NTC behavior drops from (400–260 °C) ±10%. The material was pressed into pellets and sintered at 700 °C for 3 h resulting in good bonding strength. Electrical characterization of the material was done by measuring the resistance over a temperature range of 100–400 °C. The material showed reproducible NTC characteristics over the temperature range 400, 370, 340, 280, and 260 °C with decreasing thermistor constant values (B = 9588, 9210, 8500, 5170, 3330 K⁻¹) and activation energy (ΔE = 826, 794, 733, 445, 287 meV), respectively. The decrease in activation energy of the ceramic powder with increase in La₂O₃ concentration makes it possible to fabricate thermal sensors which can be used in different temperature ranges. The microstructure was studied using SEM and evidence of a sintered body with grain size around 1 μm was observed in the material. XRD analysis indicated the single-phase tetragonal structure of the ceramic material. The process of using this ceramic material for fabrication of 10 ft continuous fire wire sensor has been explained.     

Electrogenerated chemiluminescence sensor for itopride with Ru(bpy)3-doped silica nanoparticles/chitosan composite films modified electrode

A electrogenerated chemiluminescence (ECL) sensor for itopride was developed based on tris(2,2-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺)-doped silica (RuDS) nanoparticles/biopolymer chitosan composites membrane modified glassy carbon electrode (GCE). The RuDS nanoparticles (52 ± 5 nm) were prepared by a modified Stőber synthesis method and were characterized by electrochemical, fluorometric and transmission electron microscopy technology. The Ru(bpy)₃²⁺ encapsulation interior of the silica nanoparticle maintains its electrochemical activities and also reduces Ru(bpy)₃²⁺ leaching from the silica matrix when immersed in water due to the electrostatic interaction. The ECL analytical performances of this ECL sensor for itopride based on its enhancement ECL emission of Ru(bpy)₃²⁺ were investigated in details. Under the optimum condition, the enhanced ECL intensity was linear with the itopride concentration in the range of 1 × 10⁻⁸ to 2 × 10⁻⁵ g/mL (R = 0.9978). The detection limit was 3 × 10⁻⁹ g/mL, and the relative standard deviation was 2.3% for 8 × 10⁻⁸ g/mL itopride (n = 11). The method was successfully applied to the determination of itopride in pharmaceutical and human serum samples with satisfactory results. The as-prepared ECL sensor for the determination of itopride displayed good sensitivity and stability.     

How age affects the speed of perception of computer icons

The use of computers is constantly increasing. At the same time the population of the industrialised world is aging. In this study we investigated the speed with which users of different ages can find a specific computer icon from a group of others. Our results show that search performance slows with age when calculated across all three levels of inter-icon spacing (χ² (4) = 14.904, p < .05) and icon size (χ² (4) = 15.674, p < .05) used in this study. However, individual variability in search performance was very high within all age groups. Our study suggests that icons used in graphical user interfaces should be at least about 1 degree in size (about 0.7 cm at a viewing distance of 40 cm) for the majority of users to be able to perform their computerised tasks with relative ease. Also, the inter-icon spacing should be moderate, preferably about the same as the icon size. Ideally user interfaces should be adaptable to individual user needs and preferences.     

Periodic solutions of a class of nonlinear difference equations via critical point method

In this paper, we obtain some new sufficient conditions for the existence of nontrivial m-periodic solutions of the following nonlinear difference equation

by using the critical point method, where f: Z × R → R is continuous in the second variable, m ≥ 2 is a given positive integer, p_n+m = p_n for any n  Z and f(t + m, z) = f(t, z) for any (t, z)  Z × R, (−1)^δ = −1 and δ > 0.     

Performance characteristic studies of glucose biosensors modified by (3-mercaptopropyl)trimethoxysilane sol–gel and non-conducting polyaniline

The materials (3-mercaptopropyl)trimethoxysilane (MPTMS) sol–gel and non-conducting polyaniline (PAn) were prepared for coating on two different amperometric biosensors fabricated by the immobilization of glucose oxidase (GOx) in conducting polyaniline (PA) as permselective membranes. A few performance characteristics of the MPTMS and the PAn-modified glucose sensors are comparable. In detecting 1 mM glucose, the biosensors’ response times were 11 and 12 s, respectively, and results from the repeating measurements (N = 10) showed that R.S.D. = 2.09 and 1.70%, respectively. The detection linearity of the two biosensors was up to 12.5 mM with R = 0.9989 and 0.9969. When they were used to detect 0.5 mM of ascorbic acid (AA), uric acid (UA), and acetaminophen at an anodic potential of 0.4 V, current signals were either insignificant or invisible. The PAn-coated glucose sensor exhibited superior sensitivity at 18.91 μA/(mM cm²), and a maximum current density of 3.70 mA/cm². GOx in the MPTMS-modified biosensor presented a stronger affinity to glucose with K_m = 48.87. More importantly, the stability of this biosensor is superior to that of the PAn-modified biosensor and has lasted for almost 5 months.     

Room temperature hydrogen response kinetics of nano–micro-integrated doped tin oxide sensor

The nano–micro-integrated sensor has been fabricated by sol–gel depositing the nanocrystalline indium oxide (In₂O₃)-doped tin oxide (SnO₂) thin film on microelectromechanical systems (MEMS) device having interdigitated electrode configurations with two different electrode spacing (10 μm and 20 μm) and two different number of fingers (8 and 20). The present nano–micro-integrated sensor exhibits high H₂ sensitivity range (S = 3–10⁵) for the H₂ concentration within the range of 100–15,000 ppm at room temperature. It has been demonstrated that, the room temperature response kinetics of the present nano–micro-integrated sensor is a function of finger spacing, H₂ concentration and air-pressure, but independent of number of fingers. Such dependence has been explained on the basis of Le Chatelier's principle applied to the associated H₂ sensing mechanism and the role of above parameters in shifting the dynamic equilibrium of the involved surface reactions under the described test conditions. A new definition of the response time has been proposed, which is not only suitable for the theoretical analysis but also for the practical applications, where a gas-leak detection alarm is required to be triggered.     

Properties of Noncentral Dirichlet Distributions

Let X₁,…, X_r+1 be independent random variables, X_iGa (a_i, θ, δ_i), i = 1,…, r + 1. Define and V_i = X_i/X_r+1, i = 1,…, r. Then, (U₁,…, U_r) and (V₁,…, V_r) follow noncentral Dirichlet Type 1 and Type 2 distributions, respectively. In this article several properties of these distributions and their connections with the uniform, the noncentral multivariate-F and the noncentral multivariate-t distributions are discussed.     

UV-LIGA interferometer biosensor based on the SU-8 optical waveguide

SU-8 resist was used as a core/cladding waveguide material to fabricate a Mach–Zehnder interferometer (MZI) for biochemical sensing. The refractive index of the SU-8 resist was fine-tuned with a Δn of 0.004 for single-mode transmission. The UV lithography processes of the SU-8 resist were also optimized to pattern the high resolution (1 μm) and high aspect ratio (A_R = 6) Y-branch structure of the optical interferometer. Optical measurements reveal that the SU-8 MZI chip can efficiently transmit the NIR laser (λ = 1310 nm) with a total loss less than 6 dB. When one branch of the MZI is in contact with the analyte, the interfered intensity stabilizes after the soaking time exceeds 5 min. NaCl solution with a concentration of 10⁻⁹ g/l can be detected using the SU-8 MZI chip. In the future, the polymer MZI chip can be mass-produced by molding process (or the LIGA process). The low-cost, label-free, real-time and high-sensitivity MZI chip will benefit many applications related to biological, environmental and industrial detection.     

Microstructure, electrical and ethanol-sensing properties of perovskite-type SmFe0.7Co0.3O3

Ultrafine SmFe_0.7Co_0.3O₃ powder, prepared by a sol–gel method, shows a single-phase orthogonal perovskite structure. The influence of annealing temperature upon its crystal cell volume, microstructure, electrical and ethanol-sensing properties was investigated in detail. When the annealing temperature increases from 600 to 950 °C, the unit cell volume of the SmFe_0.7Co_0.3O₃ sample reduces, and its average grain size increases. When the annealing temperature increases from 600 to 850 °C, the optimal working temperature and response to ethanol of the SmFe_0.7Co_0.3O₃ sensor increase, and the response–recovery time shortens. But when the annealing temperature further increases from 850 to 950 °C, there are decreases of the optimal working temperature and sensor response, and the response–recovery time is prolonged. The results indicate that, as for sensor response, its optimal annealing temperature is about 850 °C, and the sensor based on SmFe_0.7Co_0.3O₃ annealed at 850 °C shows the highest response S = 80.8 to 300 ppm ethanol gas, and it has the best response–recovery and selectivity characteristics. When the ethanol concentration is as low as 500 ppm, the curve of its optimal response versus concentration is nearly linear. Meanwhile, the influence mechanisms of annealing temperature upon the conductance, the optimal working temperature and sensor response for SmFe_0.7Co_0.3O₃ were studied.     

A colorimetric response to hydrogen sulfide

Two simple Cu(II) chromophores [Cu(acac)(dmp)](NO₃) (1) and [Cu(acac)(dpph)](NO₃) (2) (acac = acetylacetone, dmp = 2,9-dimethyl-1,10-phenanthroline and dpph = 4,7-diphenyl-1,10-phenanthroline) have been synthesised and immobilized into a highly permeable polymer matrix and subsequently used in the optical detection of low levels of hydrogen sulfide (10 ppm) over a 2 min period. The system is responsive to a concentration one-tenth that quoted as being immediately dangerous to life and health (IDLH) value (100 ppm) by the National Institute for Occupational Safety and Health (NIOSH). The UV–vis spectral change is a consequence of the hydrogen sulfide gas reducing the Cu(II) to Cu(I) in the polymer matrix. A crystal structure of [Cu(acac)(dpph)](NO₃) (2) was obtained and will also be discussed.     

Impedancemetric gas sensor based on Pt and WO3 co-loaded TiO2 and ZrO2 as total NOx sensing materials

Pt-loaded metal oxides [WO₃/ZrO₂, MO_x/TiO₂ (MO_x = WO₃, MoO₃, V₂O₅), WO₃ and TiO₂] equipped with interdigital Au electrodes have been tested as a NO_x (NO and NO₂) gas sensor at 500 °C. The impedance value at 4 Hz was used as a sensing signal. Among the samples tested, Pt-WO₃/TiO₂ showed the highest sensor response magnitude to NO. The sensor was found to respond consistently and rapidly to change in concentration of NO and NO₂ in the oxygen rich and moist gas mixture at 500 °C. The 90% response and 90% recovery times were as short as less than 5–10 s. The impedance at 4 Hz of the present device was found to vary almost linearly with the logarithm of NO_x (NO or NO₂) concentration from 10 to 570 ppm. Pt-WO₃/TiO₂ showed responses to NO and NO₂ of the same algebraic sign and nearly the same magnitude, while Pt/WO₃ and WO₃/TiO₂ showed higher response to NO than NO₂. The impedance at 4 Hz in the presence of NO for Pt-WO₃/TiO₂ was almost equal at any O₂ concentration examined (1–99%), while in the case of Pt/WO₃ and WO₃/TiO₂ the impedance increased with the oxygen concentration. The features of Pt-WO₃/TiO₂ are favorable as a NO_x sensor that can monitor and control the NO_x concentration in automotive exhaust. The effect of WO₃ loading of Pt-WO₃/ZrO₂-based sensor is studied to discuss the role of surface W-OH sites on the NO_x sensing.     

Inversion of a radiative transfer model for estimating vegetation LAI and chlorophyll in a heterogeneous grassland

Radiative transfer models have seldom been applied for studying heterogeneous grassland canopies. Here, the potential of radiative transfer modeling to predict LAI and leaf and canopy chlorophyll contents in a heterogeneous Mediterranean grassland is investigated. The widely used PROSAIL model was inverted with canopy spectral reflectance measurements by means of a look-up table (LUT). Canopy spectral measurements were acquired in the field using a GER 3700 spectroradiometer, along with simultaneous in situ measurements of LAI and leaf chlorophyll content. We tested the impact of using multiple solutions, stratification (according to species richness), and spectral subsetting on parameter retrieval. To assess the performance of the model inversion, the normalized RMSE and R² between independent in situ measurements and estimated parameters were used. Of the three investigated plant characteristics, canopy chlorophyll content was estimated with the highest accuracy (R² = 0.70, NRMSE = 0.18). Leaf chlorophyll content, on the other hand, could not be estimated with acceptable accuracy, while LAI was estimated with intermediate accuracy (R² = 0.59, NRMSE = 0.18). When only sample plots with up to two species were considered (n = 107), the estimation accuracy for all investigated variables (LAI, canopy chlorophyll content and leaf chlorophyll content) increased (NRMSE = 0.14, 0.16, 0.19, respectively). This shows the limits of the PROSAIL radiative transfer model in the case of very heterogeneous conditions. We also found that a carefully selected spectral subset contains sufficient information for a successful model inversion. Our results confirm the potential of model inversion for estimating vegetation biophysical parameters at the canopy scale in (moderately) heterogeneous grasslands using hyperspectral measurements.     

An approach to mining bundled commodities

Although bundled commodities are largely existed in supermarket, there are few investigations about bundled commodities mining. In this study, interval-valued association rules as a novel and possible approach to solving the bundled commodities mining issue, is proposed. Properties research based on interval-valued association rules is conducted, and an interval-valued rule pattern: F, ,  is constructed, where F denotes set of interval-valued ruses, and denote the disjunctive operation and conjunctive operation, respectively. Furthermore, one of the properties satisfied by the interval-valued rules: A  C = B  C and A  C = B  C  A = B, where A, B, C are there different rules, is validated and utilized to mine the bundled commodities. Finally, a large-scale software engineering project relative to interval-valued rule mining is implemented to merge flight testing information about aircrafts which validates the technique of mining bundled commodities can be discovered a special relation between objects. These initial investigations provide a researchable framework for bundled commodities mining.     

Development of an optical hydrogen sulphide sensor

A hydrogen sulphide (H₂S)-sensitive optode film has been fabricated by immobilising tetraoctylammonium fluorescein mercury(II) acetate (TOFMA) and tri-n-butyl phosphate in a poly(vinyl chloride) (PVC) matrix. The optode film, coated on an overhead transparency film, was employed as a sensing device for fluorimetric detection of H₂S. The fluorescence intensity monitored at 553 nm (excitation at 503 nm) increased with increasing H₂S concentrations. The optode film showed a good, linear and reversible response to H₂S from 0 to 15 ppm (v/v). It was optically stable and the reproducible response of the film on exposure to 10 ppm (v/v) H₂S was extremely good. There was no sign of degradation after 8 h of continuous use. The response to H₂S levelled off at about 27.5 ppm The response and recovery times of the optical H₂S sensor were fast and less than 2 and 5 s, respectively. An optically-based sensor for H₂S determination was successfully developed. It was anticipated that the system could be used to monitor H₂S with a concentration range of 0–25 ppm (v/v) with satisfactory results. A proposed mechanism for the detection of H₂S by the optode films is described.     

Highly efficient and stable white organic light emitting diode with triply doped structure

A triply doped white organic light emitting diode with red and blue dyes in the light emitting layer and a green dye in another layer is proposed. The device structure was CuPc(12 nm)/NPB(40 nm)/ADN:DCJTB(0.2%):TBPe(1%)(50 nm)/Alq:C545(0.5%)(12 nm)/LiF(4 nm)/Al. Here copper phthalocyanine (CuPc) is a buffer layer, N,N′-di(naphthalene-1-y1)-N,N′-dipheyl-benzidine (NPB) is a hole transporting layer, 9,10-di-(2-naphthyl) anthracene (ADN) is blue emitting layer, tris (8-quinolinolato)aluminium complex (Alq) is an electron transporting layer, 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetramethyljulolidy1-9-enyl)-4H- pyran (DCJTB), 2,5,8,11-tetra-butylperylene (TBPe), Coumarin6 and deveriative (C545) are red, blue and green dyes, respectively. This device shows a luminance of 21200 cd/m² at driving current of 400 mA/cm² and 1026 cd/m² at 20 mA/cm². Its efficiency is 6 cd/A and 3.11 Lm/W. It also shows a higher operating stability: the half lifetime is 22,245 h at an initial luminance of 100 cd/m², while the driving voltage increased only 0.3 V.     

A hydrogen peroxide biosensor based on direct electrochemistry of hemoglobin in Hb–Ag sol films

Hemoglobin (Hb) was used as a template to fabricate hemoglobin–silver (Hb–Ag) sol in which the hemoglobin showed direct electrochemistry on a glass carbon (GC) electrode. Ultraviolet–visible (UV–vis) spectra and reflectance absorption infrared (RAIR) spectra suggested that hemoglobin in Hb–Ag sol retained its native secondary structure. Scanning electron microscopy (SEM) demonstrated that the morphology of the Hb film was much different from the Hb–Ag sol film. The Hb–Ag film proved to exhibit a good electrocatalytic activity for the reduction of hydrogen peroxide. Based on this, a novel amperometric hydrogen peroxide biosensor was developed, which showed a sensitive response to the reduction of H₂O₂ without any electron mediator. Under optimum conditions, the biosensor responded linearly to H₂O₂ in the concentration range of 1 × 10⁻⁶ to 2.5 × 10⁻² M with detection limit of 1 × 10⁻⁷ M at 3σ. Moreover, the studied biosensor exhibited high sensibility, good reproducibility, and long-term stability.     

Flow over a bluff body from moderate to high Reynolds numbers using large eddy simulation

Large eddy simulation (LES) is performed to study the uniform approach flow over a square-section cylinder with different Reynolds numbers, ranging from 10³ to 5 × 10⁶. Two different sub-grid scale models, the Smagorinsky and a dynamic one-equation model, are employed. An incompressible finite-volume code, based on a non-staggered grid arrangement and an implicit fractional step method with second-order accuracy in space and time, is used.

The structure of the flow is studied with the instantaneous and the mean quantities such as pressure, turbulent stresses, turbulent kinetic energy, vorticity, the second invariant of velocity gradient and streamlines. The Strouhal number, the mean and RMS values of the lift and drag are computed for various Reynolds numbers, which show a good agreement with the available experimental results. It is found that the effect of Reynolds number on the global quantities, the mean and the large scale instantaneous flow-structures is not much at the higher Reynolds numbers, i.e. Re > 2 × 10⁴. In this range of Reynolds numbers, the small scales of the instantaneous structures are more complex and chaotic as they compare with the larger ones.