Hydrogenation behavior of high-energy ball milled amorphous Mg2Ni catalyzed by multi-walled carbon nanotubes

Amorphous Mg₂Ni alloy was successfully synthesized by means of mechanical alloying. Then, the multi-walled carbon nanotubes (MWCNTs) were added by high-energy ball milling to catalyze the amorphous alloy. The X-ray diffraction (XRD) spectroscopy reveal that the as-cast Mg₂Ni alloy has presented a completely amorphous state under specific conditions of high-energy ball milling process. Different process parameters of ball-to-powder ratio (10:1, 20:1, 40:1) and milling time have been attempted for the preparation of amorphous Mg₂Ni alloy. The results show that the milling time and ball-to-powder weight ratio have significantly influence on the amorphization process of crystalline Mg₂Ni alloy. Before and after the milling, phase compositions and microstructures of the prepared materials were characterized by XRD, scanning electron microscope (SEM), electron energy dispersion spectrum (EDS) and transition electron microscope (TEM) approaches. The morphology of composite Mg₂Ni/MWCNTs was investigated, the TEM images show that the MWCNTs imbed on the surface of the particles after milling for 1 h, and the MWCNTs with and without tubular structure have been observed. The hydrogen storage properties of amorphous Mg₂Ni alloys were improved by the catalytic effect of MWCNTs. The catalytic effect and mechanism of MWCNTs on the hydrogen storage properties of amorphous Mg₂Ni alloy are discussed and investigated.     

Isothermal activation,thermodynamic and hysteresis of MgH2 hydrides catalytically modified by high-energy ball milling with MWCNTs and TiF3

MgH₂-M (M = MWCNTs or TiF₃ or both of them) composites prepared by high-energy ball milling (HEBM) are used in this work to illustrate the effect of catalysts on isothermal activation, thermodynamic and hysteresis of MgH₂ hydrides. The phase compositions, microstructures, particle morphologies and distributions of MgH₂ with catalysts have been evaluated. The isothermal synergetic catalytic-activation and dehydrogenation effect of MWCNTs and TiF₃ evaluated by P-C-T give the evidences that the addition of catalysts is an effective strategy to destabilize MgH₂ and reduce the dehydrogenation temperatures. The isothermal activation process can be remarkly accelerated by adding MWCNTs or TiF₃. It's worthnoting that fast initial absorption rate and high hydrogenation capacity are obtained for modified MgH₂ when adding MWCNTs coupling with TiF₃ and no special activation treatment is needed. The activation effect is mainly attributed to the large contraction/expansion stresses caused by accelerated catalytic desorption/absorption cycles. The catalytic effect on thermodynamic is mainly attributed to electronic exchange reactions with hydrogen molecules during the dissociation-absorption or recombination-desorption process. The thermodynamic hysteresis of catalyzed MgH₂ is also investigated to evaluate the energy consumption and estimate the efficiency of the isothermal hydrogen absorption/desorption process. A probable synergetic catalytic-activation mechanism is probed.     

Catalytic effect of Ni, Mg2Ni and Mg2NiH4 upon hydrogen desorption from MgH2

MgH₂ is a perspective hydrogen storage material whose main advantage is a relatively high hydrogen storage capacity (theoretically, 7.6 wt.% H₂). This compound, however, shows poor hydrogen desorption kinetics. Much effort was devoted in the past to finding possible ways of enhancing hydrogen desorption rate from MgH₂, which would bring this material closer to technical applications. One possible way is catalysis of hydrogen desorption. This paper investigates separate catalytic effects of Ni, Mg₂Ni and Mg₂NiH₄ on the hydrogen desorption characteristics of MgH₂. It was observed that the catalytic efficiency of Mg₂NiH₄ was considerably higher than that of pure Ni and non-hydrated intermetallic Mg₂Ni. The Mg₂NiH₄ phase has two low-temperature modifications below 508 K: un-twinned phase LT1 and micro-twinned phase LT2. LT1 was observed to have significantly higher catalytic efficiency than LT2.     

Nanocrystalline β-γ-β cyclic phase transformation in reacted ball milled MgH2 powders

Pure magnesium powders were ball milled under a hydrogen pressure of 50 bar at room temperature, using reactive ball milling (RBM) approach. The results have shown that a single stable phase of β-MgH₂ is obtained upon RBM for 25 h. Increasing the RBM time leads to a significant decreasing on the grain size and an increase in the iron contamination that were introduced to the powders upon using hard steel milling tools. Remarkable changes in the transformed mass fractions of β-MgH₂ phase to a metastable γ-MgH₂ phase with increasing the RBM time could be detected. Cyclic β-γ-β phase transformations were observed several times upon changing the RBM time. After 200 h of RBM time, the decomposition temperature and activation energy were recorded to be 399 °C and 131 kJ/mol, respectively. Moreover, the times required for complete absorption and desorption of 7 wt.% of hydrogen at 250 °C were recorded to be 3140 s and 35,207 s under 10 and 0 bar, respectively. At 300 °C, the powders that were obtained upon RBM time for 200 h possess excellent hydrogenation properties for any pure MgH₂ system, indexed by high hydrogen storage capacity (7.54 wt.%) with complete 600 absorption/desorption cycles. Improvements of hydrogenation/dehydrogenation kinetics are attributed to the presence of γ-phase, the existence of Fe contamination and the nanocrystallinity of the ball milled powders.     

Effects of SnO2 on hydrogen desorption of MgH2

The hydrogen desorption properties of Magnesium Hydride (MgH₂) ball milled with cassiterite (SnO₂) have been investigated by X-ray powder diffraction and thermal analysis. Milling of pure MgH₂ leads to a reduction of the desorption temperature (up to 60 K) and of the activation energy, but also to a reduction of the quantity of desorbed hydrogen, referred to the total MgH₂ present, from 7.8 down to 4.4 wt%. SnO₂ addition preserves the beneficial effects of grinding on the desorption kinetics and limits the decrease of desorbed hydrogen. Best tradeoff – activation energy lowered from 175 to 148 kJ/mol and desorbed hydrogen, referred to the total MgH₂ present, lowered from 7.8 to 6.8 wt% – was obtained by co-milling MgH₂ with 20 wt% SnO₂.     

Hydrogen storage properties of MgxFe (x: 2, 3 and 15) compounds produced by reactive ball milling

This work deals with the assessment of the thermo-kinetic properties of Mg–Fe based materials for hydrogen storage. Samples are prepared from Mg_xFe (x: 2, 3 and 15) elemental powder mixtures via low energy ball milling under hydrogen atmosphere at room temperature. The highest yield is obtained with Mg₁₅Fe after 150 h of milling (90 wt% of MgH₂). The thermodynamic characterization carried out between 523 and 673 K shows that the obtained Mg–Fe–H hydride systems have similar thermodynamic parameters, i.e. enthalpy and entropy. However, in equilibrium conditions, Mg₁₅Fe has higher hydrogen capacity and small hysteresis. In dynamic conditions, Mg₁₅Fe also shows better hydrogen capacity (4.85 wt% at 623 K absorbed in less than 10 min and after 100 absorption/desorption cycles), reasonably good absorption/desorption times and cycling stability in comparison to the other studied compositions. From hydrogen uptake rate measurements performed at 573 and 623 K, the rate-limiting step of the hydrogen uptake reaction is determined by fitting particle kinetic models. According to our results, the hydrogen uptake is diffusion controlled, and this mechanism does not change with the Mg–Fe proportion and temperature.     

H2 storage on single- and multi-walled carbon nanotubes

The adsorption of hydrogen on single-walled and multi-walled carbon nanotubes (CNTs) was investigated at 77 and 298 K, in the pressure range of 0–1000 Torr. The adsorption isotherms indicate that adsorption follows the Langmuir model. Hydrogen uptakes were found to depend strongly on the nature of the CNTs. Single-walled CNTs adsorb significantly higher quantities of hydrogen per unit mass of the solid, while the opposite is true on a per unit surface area basis. This observation implies that adsorption takes place selectively on specific sites on the surface. The hydrogen uptake capacity of CNTs was also found to be affected by the purity of the materials, increasing with increasing purity. Temperature programmed desorption indicated that relatively strong adsorption bonds develop between adsorbent and adsorbate and that a single type of adsorption site exists on the solid surface.     

Processing of LiBH4 from its elements by ball milling method

Investigations of alternative renewable energy resources continue, with many studies concentrating on hydrogen storage. However, there are a few problems such as storage, transportation, delivery to the user and usage safely, to be addressed to facilitate commercialization and wide usage of the hydrogen. The absorbed form within the metal hydrides seems to be the best solution of this problem. Since Li is the lightest metal, it has the advantage as the stored amount of hydrogen mass ratio. LiBH₄ production process was investigated using elemental Li, B and H₂. Spex type ball milling with tungsten carbide, stainless steel and zirconia type vessels, was used to mix the different amount of Li and B under argon atmosphere. X-ray diffraction pattern demonstrated that the LiB was obtained. A system was designed to provide a hydrogen atmosphere of 60 bars to force hydrogen into the LiB structure. FTIR analysis strongly indicated the LiBH₄ compound when the mol ratio of B/Li is 0.214. Thermal decomposition and heat flow experiments performed simultaneously with DSC and TGA techniques also indicate hydrogen-rich structure showing greater mass loss. One gram of lithium borohydride sample released 1423 ml of hydrogen with Ni catalyst while NiO caused 1972.94 ml of hydrogen gas desorption, equaling to 90% of the theoretical yield of commercial LiBH₄. Indicating that, hydrogen of water can be obtained by either Ni or NiO catalysts.     

Reactivity of complex hydrides Mg2FeH6, Mg2CoH5 and Mg2NiH4 with lithium ion: Far from equilibrium electrochemically driven conversion reactions

The electrochemical reaction of lithium ion with Mg₂FeH₆, Mg₂CoH₅ and Mg₂NiH₄ complex hydrides prepared by reactive grinding is studied here. Plateaus at an average potential of 0.25 V, 0.24 V and 0.27 V corresponding to discharge capacities of 6.6, 5.5 and 3.6 Li can be achieved respectively for Mg₂FeH₆, Mg₂CoH₅ and Mg₂NiH₄. From in situ X-ray diffraction (XRD) characterizations of complex hydride based electrodes, dehydrogenation leads to a decrease of the intensities of the diffraction peaks suggesting a strong loss of crystallinity since formation of Mg and M (M = Fe, Co, Ni) peaks is not observed. ⁵⁷Fe Mössbauer spectroscopy confirms the formation of nanoscale Fe or an amorphous Mg–Fe alloy during the decomposition of Mg₂FeH_6. Interestingly, lattice parameter variations suggest phase transitions in the Mg₂NiH₄ system involving the formation of low hydrogen content hydride Mg₂NiH, while an increase of lattice parameters of Mg₂CoH₅ hydride could be attributed to the formation of a Mg₂CoH₅Li_x solid solution compound up to x = 1.     

Hydrogen storage in carbon/Mg nanocomposites synthesized by ball milling

Carbon nanocomposites obtained by ball milling of graphite and magnesium with organic additives (benzene or cyclohexane) under different conditions have been studied with the aim of preparing novel hydrogen storage materials. It has been proved by thermal desorption spectrometry (TDS) and neutron diffraction measurements that the hydrogen taken up by the nanocomposites exists in at least two states; the one is the hydrogen strongly associated with the carbon component and the other the hydride in the magnesium component. The ball milling resulted in the generation of large amounts of dangling carbon bonds in graphite, which acted as active sites to take up the hydrogen. When _D2${\mathrm{D}}_2$ gas was brought into contact with such composites, the isotope exchange reaction with the hydrogen in the magnesium hydride occurred at 453 K, and not with the hydrogen associated with the carbon. The properties of such hydrogen taken up were also discussed from the standpoint of isotope effects.     

Enhanced dehydrogenation and rehydrogenation properties of LiBH4 catalyzed by graphene

The investigation of thermally induced dehydrogenation of LiBH₄ reveals that LiBH₄ doped with the graphene catalysts shows superior dehydrogenation and rehydrogenation performance to that of Vulcan XC-72, carbon nanotube and BP2000 doped LiBH₄. For doping with 20 wt.% graphene, thermal dehydrogenation of LiBH₄ is found to start at ca. 230 °C and a total weight loss of 11.4 wt.% can be obtained below 700 °C. With increased loading of graphene within a LiBH₄ sample, the onset dehydrogenation temperature and the two main desorption peaks from LiBH₄ are found to decrease while the hydrogen release amount is found to increase. Moreover, variation of the equilibrium pressure obtained from isotherms measured at 350–450 °C indicate the dehydrogenation enthalpy is reduced from 74 kJ mol⁻¹ H₂ for pure LiBH₄ to ca. 40 kJ mol⁻¹ H₂ for 20 wt.% graphene doped LiBH₄. Importantly, the reversible dehydrogenation/rehydrogenation process was achieved under 3 MPa H₂ at 400 °C for 10 h, with a capacity of ca. 4.0 wt.% in the tenth cycle. Especially, LiBH₄ is reformed and new species, Li₂B₁₀H₁₀, is detected after the rehydrogenation process.     

Improvement in desorption kinetics of NaAlH4 catalyzed with TiO2 nanopowder

NaAlH₄ has been homogeneously mixed with micron- and nano-sized TiO₂ powders by high-energy ball milling and their sorption properties have been investigated during hydrogen absorption/desorption cycles. NaAlH₄ with TiO₂ nanopowder exhibits as good desorption kinetics as NaAlH₄ with TiCl₃, whereas poor desorption kinetics is observed with micron-sized TiO₂ powder. NaAlH₄ with TiO₂ nanopowder also provides improved cyclic property compared to NaAlH₄ with TiCl₃ in terms of both desorption rate and hydrogen capacity. X-ray diffraction analysis shows that micron-sized TiO₂ remains stable with NaAlH₄ after milling, although thermodynamic calculation predicts that TiO₂ reacts with NaAlH₄.     

Role of particle size,grain size,microstrain and lattice distortion in improved dehydrogenation properties of the ball-milled Mg(AlH4)2

The decreased dehydrogenation temperature and improved dehydrogenation kinetics were achieved by high-energy ball milling Mg(AlH₄)₂. The particle size, grain size, microstrain and lattice distortion of the post-milled samples, i.e., from macro- to micro-scale, were systematically characterized by means of SEM and XRD measurements. The results indicated that the high-energy ball milling process led to not only a decrease in the particle size and grain size but also an increase in the microstrain and lattice distortion, which provides a synergetic effect of the thermodynamics and kinetics on lowering the dehydrogenation temperatures of the post-milled Mg(AlH₄)₂ samples. From the kinetic point of view, the refinement of the particles and grains shortens the diffusion distance, and the increase of the microstrain and lattice distortion enhances the diffusivity, which work together to decrease the apparent activation energy for hydrogen desorption. Besides, the presence of microstrain and lattice distortion increased the free energy of the post-milled samples, which was released by recovery and recrystallization processes upon heating. This offers more heat release during the first-step dehydrogenation, consequently leading to thermodynamically decline in dehydrogenation temperatures of the post-milled samples. Such a finding provides insights into the mechanistic understanding on decreased dehydrogenation temperature and improved dehydrogenation kinetics of the post-milled metal hydrides as hydrogen storage materials.     

Microstructure of ball milled MgH2 powders upon hydrogen cycling: An electron microscopy study

Microstructure of MgH₂ powder particles milled for 5–60 h was studied after the powders were hydrogen cycled. Using electron microscopy we estimated individual grain size and particle size of cycled powders to compare with those before H-cycling. The nano-size grains were found to grow (3–10 times) whereas the particles undergo a mild refinement upon H-cycling. The most prominent grain growth was within the 1st dehydrogenation. The smaller grains in the milled powders demonstrated faster growth upon cycling. The average grain size estimated in this study for the cycled powders were >200 nm. The grain and particle size approached a regular or log-normal distribution with cycling. The lattice strain introduced in the milled MgH₂ powders was significantly removed by cycling for less milled powders (milled for <15 h). Longer milled (30–60 h) MgH₂ powders could not fully recover from lattice strain by H-cycles (six cycles) as observed in the present study.     

Adjustment of the decomposition path for Na2LiAlH6 by TiF3 addition

The decomposition of Na₂LiAlH₆ is studied by in-situ synchrotron diffraction. By addition of TiF₃ and dehydrogenation-rehydrogenation cycling of the samples new decomposition paths are found. Na₃AlH₆ is formed on decomposition in the presence of TiF₃. The additive brings the system closer to equilibrium, and decomposition through Na₃AlH₆ is demonstrated for the first time. The results are in agreement with previously published computational data. For a cycled sample with 10 mol% TiF₃ Na₂LiAlH₆ decomposes fully into Na₃AlH₆ before further decomposition to NaH and Al. This shows clear changes in the kinetics of the system, and may open possibilities of tailoring the decomposition path by the use of additives.     

Hydrogen absorption/desorption behavior of Mg50La20Ni30 bulk metallic glass

In this work, Mg₅₀La₂₀Ni₃₀ bulk metallic glass (BMG) was prepared and its hydrogen absorption/desorption behavior was studied. The amorphous structure was found to be retained after gaseous hydrogenation. The T_g and T_x of the hydrogenated Mg₅₀La₂₀Ni₃₀ BMG was 561 K and 619 K respectively, much higher than the corresponding value of 463 K and 504 K of the unhydrogenated sample. Mg₅₀La₂₀Ni₃₀ BMG absorbed 0.73 and 1.85 wt% hydrogen within 1 h at 313 K and 423 K respectively, which was higher than that of ball-milled Mg₂Ni alloy. Mg₅₀La₂₀Ni₃₀ BMG exhibited an equilibrium hydrogen absorption plateau with a pressure of 0.07 MPa in pressure–composition isotherm curve at 423 K. It suggested that Mg-based BMGs are promising materials for hydrogen storage applications.     

Direct synthesis of Mg(AlH4)2 and CaAlH5 crystalline compounds by ball milling and their potential as hydrogen storage materials

Mg(AlH₄)₂ and CaAlH₅ were synthesized by direct ball milling of AlH₃ and MgH₂ or AlH₃ and CaH₂ hydrides. The XRD profiles indicated crystalline compounds. Several ball-milling conditions were studied and the optimum parameters were found. Among these, the key parameter is the pause used to cool down the milling device, which allows reducing the temperature rise during milling. Thus, the maximum yield of complex hydrides was obtained by minimizing the desorbed alane amount. The decomposition properties were studied and were in agreement with those reported for different synthesis methods. Mg(AlH₄)₂ with a good hydrogen capacity and a decomposition reaction enthalpy close to 0 kJ/mol H₂ can be a candidate for one-way storage systems. As for CaAlH₅, it might be suitable for reversible hydrogen storage thanks to its dehydrogenation reaction enthalpy (26 kJ/mol H₂). However, rather high activation energy values were evaluated for both compounds (119 and 161 kJ/mol, respectively).     

Hydrogen evolution from hydrolysis of ammonia borane catalyzed by Rh/g-C3N4 under mild conditions

Developing effective catalysts for hydrogen evolution from hydrolysis of ammonia borane (AB) is of great significance considering the useful applications of hydrogen. Herein, graphitic carbon nitride (g-C₃N₄) prepared through the simply pyrolysis of urea was employed as a support for Rh nanoparticles (NPs) stabilization. The in-situ generated Rh NPs supported on g-C₃N₄ with an average size of 3.1 nm were investigated as catalysts for hydrogen generation from the hydrolysis of AB under mild conditions. The Rh/g-C₃N₄ catalyst exhibits a high turnover frequency of 969 mol H₂· (min·mol_Rh)^?1 and a low activation energy of 24.2 kJ/mol. The results of the kinetic studies show that the catalytic hydrolysis of AB over the Rh/g-C₃N₄ catalyst is a zero-order reaction with the AB concentration and a first-order reaction with the Rh concentration. This work demonstrates that g-C₃N₄ is a useful support to design and synthesis of effective Rh-based catalyst for hydrogen-based applications.     

Effect of ball milling time on the hydrogen storage properties of TiF3-doped LiAlH4

In the present work, the catalytic effect of TiF₃ on the dehydrogenation properties of LiAlH₄ has been investigated. Decomposition of LiAlH₄ occurs during ball milling in the presence of 4 mol% TiF₃. Different ball milling times have been used, from 0.5 h to 18 h. With ball milling time increasing, the crystallite sizes of LiAlH₄ get smaller (from 69 nm to 43 nm) and the dehydrogenation temperature becomes lower (from 80 °C to 60 °C). Half an hour ball milling makes the initial dehydrogenation temperature of doped LiAlH₄ reduce to 80 °C, which is 70 °C lower than as-received LiAlH₄. About 5.0 wt.% H₂ can be released from TiF₃-doped LiAlH₄ after 18 h ball milling in the range of 60 °C–145 °C (heating rate 2 °C min⁻¹). TiF₃ probably reacts with LiAlH₄ to form the catalyst, TiAl₃. The mechanochemical and thermochemical reactions have been clarified. However, the rehydrogenation of LiAlH₄/Li₃AlH₆ can not be realized under 95 bar H₂ in the presence of TiF₃ because of their thermodynamic properties.