Improvement of photocatalytic hydrogen generation from CdSe/CdS/TiO2 nanotube-array coaxial heterogeneous structure

The fabrication and characterization of CdSe/CdS/TiO₂ nanotube-array coaxial heterogeneous structure that has potential applications in photocatalytic water splitting and toxic pollutants degradation are investigated. CdSe(top)/CdS(under) double-layer is conformally deposited onto TiO₂ nanotubes by successive ionic layer adsorption and reaction (SILAR) and electrochemical atomic layer deposition (ECALD), respectively, for the CdS under layer and the CdSe top layer. Such double sensitized TiO₂ nanotubular photoelectrode exhibits significant enhancements in photoconversion efficiency, visible light response, and efficient hydrogen generation. The detailed synthesis process and the surface morphology, phase structure, elemental analysis, and photoelectrochemical properties of the resulting films with the CdSe/CdS/TiO₂ nanotube-array coaxial heterogeneous structure are discussed. The photoconversion efficiency of 9.47% and hydrogen generation rate of 10.24 ml h⁻¹ cm⁻² were observed. Both values are a 7-fold enhancement compared with that of the pure TiO₂ nanotube. The as-prepared photoelectrode presents potential application for industrialized photocatalytic hydrogen generation in the future.     

Enhanced hydrogen generation using ZrO2-modified coupled ZnO/TiO2 nanocomposites in the absence of noble metal co-catalyst

Mesoporous ZrO₂-modified coupled ZnO/TiO₂ nanocomposites were prepared by a surfactant assisted sol–gel method. The photocatalytic performance of these materials was investigated for H₂ evolution without noble metal co-catalyst using aqueous methanol media under AM1.5 simulated light. The H₂ evolution was compared with coupled ZnO/TiO₂, TiO₂, ZnO and Degussa P25. The ZrO₂-modified nanocomposites exhibited higher H₂ generation, specifically 0.5 wt.% ZrO₂ loading produced 30.78 mmol H₂ g⁻¹ compared to 3.55 mmol H₂ g⁻¹ obtained with coupled ZnO/TiO₂. A multiple absorbance thresholds at 435 nm and 417 nm were observed with 0.5 wt.% ZrO₂ loading, corresponding to 2.85 eV and 2.97 eV band gap energies. The high surface area, large pore volume, uniform crystallite sizes and enhanced light harvesting observed in ZrO₂-modified nanocomposites were contributing factors for effective charge separation and higher H₂ production. The possible mechanism of H₂ generation from aqueous methanol solution over ZrO₂-modified nanocomposite is presented.     

Microwave-assisted low temperature fabrication of nanostructured α-Fe2O3 electrodes for solar-driven hydrogen generation

It is demonstrated for the first time that significant enhancement of photoelectrochemical performance could be achieved by using microwave-assisted annealing for the fabrication of α-Fe₂O₃ thin films. The process can also lead to significant energy savings (>60% when compared with conventional methods). Different types of Fe thin films were oxidized using both microwave and conventional heating techniques. The photoelectrochemical performance of electrodeposited, undoped and Si-doped iron oxide samples showed that microwave-annealing resulted in superior structural and performance enhancements. The photocurrent densities obtained from microwave annealed samples are among the highest values reported for α-Fe₂O₃ photoelectrodes fabricated at low temperatures and short times; the highest photocurrent density at 0.55 V vs. V_Ag/AgCl, before the dark current onset, was 450 μA cm⁻² for the Si-doped films annealed at 270 °C for 15 min using microwave irradiation (and 180 μA cm⁻² at 0.23 V vs. V_Ag/AgCl) while conventional annealing at the same temperature resulted in samples with negligible (3 μA cm⁻²) photoactivity. In contrast, a 450 °C/15 min conventional heat treatment only resulted in a film with 25% lower photocurrent density than that of the microwave annealed sample. The improved performance is attributed to the lower processing temperatures and rapidity of the microwave method that help to retain the nanostructure of the thin films whilst restricting the grain growth to a minimum. The lower processing temperature requirements of the microwave process can also open up the possibility of fabricating hematite thin films on conducting, flexible, plastic electronic substrates.     

Microstructured extremely thin absorber solar cells

In this paper we present the realization of extremely thin absorber (ETA) solar cells employing conductive glass substrates functionalized with TiO₂ microstructures produced by embossing. Nanocrystalline or compact TiO₂ films on Indium doped tin oxide (ITO) glass substrates were embossed by pressing a silicon stamp containing a μm size raised grid structure into the TiO₂ by use of a hydraulic press (1 ton/50 cm²). The performance of these microstructured substrates in a ETA cell sensitized by a thermally evaporated or chemical bath deposited PbS film and completed by a PEDOT:PSS hole conductor layer and a Au counter electrode is compared to that of planar substrates. Surprisingly planar films produced better performance than micro-structured films. A simple model implying photoconductive shunting paths revealed by junction breakdown at negative bias under illumination is presented.     

Layered WO3/TiO2 nanostructures with enhanced photocurrent densities

Layered WO₃/TiO₂ nanostructures, fabricated by magnetron sputtering, demonstrate significantly enhanced photocurrent densities compared to individual TiO₂ and WO₃ layers. First, a large quantity of compositions having different microstructures and thicknesses were fabricated by a combinatorial approach: diverse WO₃ microstructures were obtained by adjusting sputtering pressures and depositing the films in form of wedges; later layers of TiO₂ nanocolumns were fabricated thereon by the oblique angle deposition. The obtained photocurrent densities of individual WO₃ and TiO₂ films show thickness and microstructure dependence. Among individual WO₃ layers, porous films exhibit increased photocurrent densities as compared to the dense layer. TiO₂ nanocolumns show length-dependent characteristics, where the photocurrent increases with increasing film thickness. However, by combining a WO₃-wedge type layer with a layer of TiO₂ nanocolumns, PEC properties strikingly improve, by about two orders of magnitude as compared to individual WO₃ layers. The highest photocurrent that is measured in the combinatorial library of porous WO₃/TiO₂ films is as high as 0.11 mA/cm². Efficient charge-separation and charge carrier transfer processes increase the photoconversion efficiency for such films.     

In2O3:Sn/TiO2/CdS heterojunction nanowire array photoanode in photoelectrochemical cells

The design of photoanode with highly efficient light harvesting and charge collection properties is important in photoelectrochemical (PEC) cell performance for hydrogen production. Here, we report the hierarchical In₂O₃:Sn/TiO₂/CdS heterojunction nanowire array photoanode (ITO/TiO₂/CdS-nanowire array photoanode) as it provides a short travel distance for charge carrier and long light absorption pathway by scattering effect. In addition, optical properties and device performance of the ITO/TiO₂/CdS-nanowire array photoanode were compared with the TiO₂ nanoparticle/CdS photoanode. The photocatalytic properties for water splitting were measured in the presence of sacrificial agent such as SO₃²⁻ and S²⁻ ions. Under illumination (AM 1.5G, 100 mW/cm²), ITO/TiO₂/CdS-nanowire array photoanode exhibits a photocurrent density of 8.36 mA/cm² at 0 V versus Ag/AgCl, which is four times higher than the TiO₂ nanoparticle/CdS photoanode. The maximum applied bias photon-to-current efficiency for the ITO/TiO₂/CdS-nanowire array and the TiO₂ nanoparticle/CdS photoanode were 3.33% and 2.09%, respectively. The improved light harvesting and the charge collection properties due to the increased light absorption pathway and reduced electron travel distance by ITO nanowire lead to enhancement of PEC performance.     

Photoelectrocatalytic degradation of amoxicillin over quaternary ZnO/ZnSe/CdSe/MoS2 hierarchical nanorods

Quaternary semiconductor film consists of ZnO, ZnSe, CdSe and MoS₂ was designed to establish a core-shell structure to achieve the photoelectrochemical oxidation of amoxicillin. The hybrid photoelectrode was fabricated on a FTO substrate from bath deposition methods. The hierarchical ZnSe/CdSe/MoS₂ shell was covered uniformly on ZnO nanorod core which provided a direct pathway for electron transfer, large surface area to enhance light absorption and increase active sites. The quaternary photoelectrode exhibited a photocurrent density of 26.86 mA/cm² at 0 V vs. Ag/AgCl under UV–visible light illumination, which was 31.9 times, 16.7 times and 1.6 times of that of the bare ZnO nanorods, binary ZnO/ZnSe and ternary ZnO/ZnSe/CdSe photoelectrodes, respectively. 10 ppm of amoxicillin was completely degraded in 30 min by the quaternary working electrode with an applied bias of 0.5 V vs. Ag/AgCl. The reusability and stability of quaternary electrode was demonstrated by 3-run recycling experiments. The enhanced photoelectrochemical performance of quaternary photoelectrode can be attributed to the enhancement of light absorption and increased active sites from the coverage of visible-active layers, the accelerated charge separation from the formation of p-n junction and reduced photocorrosion of CdSe from the protection of MoS₂ on the surface.     

Highly stable CdS-modified short TiO2 nanotube array electrode for efficient visible-light hydrogen generation

A highly stable photoelectrocatalytic electrode made of CdS-modified short, robust, and highly-ordered TiO₂ nanotube array for efficient visible-light hydrogen generation was prepared via sonoelectrochemical anodization and sonoelectrochemical deposition method. The short nanotube electrode possesses excellent charge separation and transfer properties, while the sonoelectrochemical deposition method improves the combination between CdS and TiO₂ nanotubes, as well as the dispersion of CdS nanoparticles. Different characterization techniques were used to study the nanocomposite electrode. UV-vis absorption and photoelectrochemical measurements proved that the CdS coating extends the visible spectrum absorption and the solar spectrum-induced photocurrent response. Comparing the photoactivity of the CdS/TiO₂ electrode obtained using sonoelectrochemical deposition method with others that synthesized using plain electrochemical deposition, the current density of the former electrode is ∼1.2 times higher that of the latter when biased at 0.5 V. A ∼7-fold enhancement in photocurrent response is obtained using the sonoelectrochemically fabricated CdS/TiO₂ electrode in comparison with the pure TiO₂ nanotube electrode. Under AM1.5 illumination the composite photoelectrode generate hydrogen at a rate of 30.3 μmol h⁻¹ cm⁻², nearly 13 times higher than that of pure titania nanotube electrode. Recycle experiments demonstrated the excellent stability and reliability of CdS/TiO₂ electrode prepared by sonoelectrochemical deposition. This composite electrode, with its strong mechanical stability and excellent combination of CdS and TiO₂ nanotubes, offers promising applications in visible-light-driven renewable energy generation.     

Photoelectrochemical hydrogen production from water/methanol decomposition using Ag/TiO2 nanocomposite thin films

Though less frequently studied for solar-hydrogen production, films are more convenient to use than powders and can be easily recycled. Anatase TiO₂ films decorated with Ag nanoparticles are synthesized by a rapid, simple, and inexpensive method. They are used to cleave water to produce H₂ under UV light in the presence of methanol as a hole scavenger. A simple and sensitive method is established here to monitor the time course of hydrogen production for ultralow amounts of TiO₂. The average hydrogen production rate of Ag/TiO₂ anatase films is 147.9 ± 35.5 μmol/h/g. Without silver, it decreases dramatically to 4.65 ± 0.39 μmol/h/g for anatase TiO₂ films and to 0.46 ± 0.66 μmol/h/g for amorphous TiO₂ films fabricated at room temperature. Our method can be used as a high through-put screening process in search of high efficiency heterogeneous photocatalysts for solar-hydrogen production from water-splitting.     

Electrochromic properties of heat-treated thin films of CeO2–TiO2–ZrO2 prepared by sol–gel route

CeO₂–TiO₂–ZrO₂ thin films were prepared using the sol–gel process and deposited on glass and ITO-coated glass substrates via dip-coating technique. The samples were heat treated between 100 and 500 °C. The heat treatment effects on the electrochromic performances of the films were determined by means of cyclic voltammetry measurements. The structural behavior of the film was characterized by atomic force microscopy and X-ray diffraction. Refractive index, extinction coefficient, and thickness of the films were determined in the 350–1000 nm wavelength, using nkd spectrophotometry analysis.Heat treatment temperature affects the electrochromic, optical, and structural properties of the film. The charge density of the samples increased from 8.8 to 14.8 mC/cm², with increasing heat-treatment temperatures from 100 to 500 °C. It was determined that the highest ratio between anodic and cathodic charge takes place with increase of temperature up to 500 °C.     

Amending charge separation and migration in TiO2 nanosheet via Au nanoparticles ensemble and its synergy in photoelectrocatalytic methanol oxidation

In this report, the preparation of an ensemble of hydrothermally synthesized TiO₂ nanosheets with Au nanoparticles (TiO₂ NSs-Au NPs) and their photoelectrocatalytic methanol oxidation behavior are accounted. The absorption spectral studies confirmed the successful emergence of Au NPs on TiO₂ NSs ensemble and the existence of Au NPs broadened the light absorption to the visible light spectrum. The crystalline and structural complexity analysis confirms the anatase TiO₂ as a major product in this synthesis. Morphology studies revealed the formation of 2 dimensional TiO₂ NSs with chemically deposited Au NPs at the TiO₂ surface and it was further confirmed by STEM-HAADF-EDS mapping studies. The ITO/TiO₂ NSs-Au modified photoelectrode showed a synergistic catalytic response towards photoelectrocatalytic methanol oxidation than the ITO/TiO₂ NSs electrode. Among them, TiO₂ NSs with 1 mM Au NPs deposited composite (TiO₂ NSs-Au (1)) showed 2-fold higher photocurrent for methanol oxidation than their pristine TiO₂ NSs. The deposited of Au NPs in TiO₂ NSs-Au nanocomposites facilitates the photoinduced charge separation and charge migration processes. Coherently the charge recombination process diminished in the TiO₂ NSs-Au nanocomposite materials. The best synergistic photoelectrocatalytic methanol oxidation reaction at the ITO/TiO₂ NSs-Au (1) modified electrode was achieved via extended visible light absorption with Schottky barrier induced enhancement of interfacial electron transfer process.     

Thin film Pt/TiO2 catalysts for the polymer electrolyte fuel cell

Thin film Pt/TiO₂ catalysts are evaluated in a polymer electrolyte electrochemical cell. Individual thin films of Pt and TiO₂, and bilayers of them, were deposited directly on Nafion membranes by thermal evaporation with varying deposition order and thickness (Pt loadings of 3–6 μg cm⁻²). Structural and chemical characterization was performed by transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). Oxygen reduction reaction (ORR) polarization plots show that the presence of a thin TiO₂ layer between the platinum and the Nafion increases the performance compared to a Pt film deposited directly on Nafion. Based on the TEM analysis, we attribute this improvement to a better dispersion of Pt on TiO₂ compared to on Nafion and in addition, substantial proton conduction through the thin TiO₂ layer. It is also shown that deposition order and the film thickness affects the performance.     

Improvement of a-Si solar cell properties by using SnO2:F TCO films coated with an ultra-thin TiO2 layer prepared by APCVD

TiO₂-overcoated SnO₂:F transparent conductive oxide films were prepared by atmospheric pressure chemical vapor deposition (APCVD) and an effect of TiO₂ layer thickness on a-Si solar cell properties was investigated. The optical properties and the structure of the TiO₂ films were evaluated by spectroscopic ellipsometry and X-ray difractometry. a-Si thin film solar cells were fabricated on the SnO₂:F films over-coated with TiO₂ films of various thicknesses (1.0, 1.5 and 2.0 nm) and I–V characteristics of these cells were measured under 1 sun (100 mW/cm² AM-1.5) illumination. It was found that the TiO₂ film deposited by APCVD has a refractive index of 2.4 at 550 nm and anatase crystal structure. The conversion efficiency of the a-Si solar cell fabricated on the 2.0 nm TiO₂-overcoated SnO₂:F film increased by 3%, which is mainly attributed to an increase in open circuit voltage (V_oc) of 30 mV.     

The effect of pre-thermal treatment of TiO2 nano-particles on the performances of dye-sensitized solar cells

We have demonstrated the effect of pre-thermal treatment of TiO₂ nano-particles on the performances of dye-sensitized solar cells (DSCs) by using high specific surface area and anatase only TiO₂ nano-particles (ca. 340 m²/g, Sachtleben Chemie GmgH, represented as HK). TiO₂ particles and thin films were characterized with X-ray diffraction, FT-IR, UV–Vis diffuse reflectance spectroscopy and FE-SEM. The photoelectrochemical properties of the thin films and the performances of DSCs were measured by photocurrent densities, AC impedance spectra and photocurrent–voltage curves. Before coating the raw TiO₂ of HK (HK-raw) on transparent conducting oxide (TCO) glass for DSC fabrication, pre-thermal treatment of HK-raw by calcining at 450 °C (HK-450) was an essential step to achieve the optimum properties in terms of morphological feature, crystallinity, specific surface area and photocurrent density. HK-450 film showed the high adsorption of dye, high photocurrent density and low interface resistance between TiO₂ and TCO glass, R_TiO2/TCO and TiO₂ and redox electrolyte, R_CT, resulting in the superior photovoltaic performance on the DSC fabricated with HK-450 and Eosin Y (or ruthenium 535 bis-TBA) at AM 1.5: open-circuit voltage of 0.62 V (0.77 V), short-circuit current of 3.03 mA/cm² (22.80 mA/cm²), fill factor of 0.57 (0.44) and overall conversion efficiency of 1.06%, (7.52%). Accordingly, the optimization between the morphological feature, specific surface area and photocurrent density of TiO₂ substrate is promising to accomplish the improved overall conversion efficiency of DSC.     

Enhanced photoelectrochemical properties of WO3 thin films fabricated by reactive magnetron sputtering

Polycrystalline WO₃ thin films were fabricated by reactive magnetron sputtering at a substrate temperature of 350 °C under different Ar/O₂ gas pressures. In order to study the thickness dependence of photoelectrochemical (PEC) behavior of WO₃, the thickness-gradient films were fabricated and patterned using a micro-machined Si-shadow mask during the deposition process. The variation of the sputter pressure leads to the evolution of different microstructures of the thin films. The films fabricated at 2 mTorr sputter pressure are dense and show diminished PEC properties, while the films fabricated at 20 mTorr and 30 mTorr are less dense and exhibit enhanced water photooxidation efficiency. The enhanced photooxidation is attributed to the coexistence of porous microstructure and space charge region enabling improved charge carrier transfer to the electrolyte and back contact. A steady-state photocurrent as high as 2.5 mA cm⁻² at 1 V vs. an Ag/AgCl (3 M KCl) reference electrode was observed. For WO₃ films fabricated at 20 mTorr and 30 mTorr, the photocurrent increases continuously up to a thickness of 600 nm.     

Chemical bath deposition synthesis of TiO2/Cu2O core/shell nanowire arrays with enhanced photoelectrochemical water splitting for H2 evolution and photostability

In this study, we have developed a facile chemical bath deposition (CBD) method to grow p-type Cu₂O nanoparticles on n-type TiO₂ nanowire arrays (TiO₂ NWAs) to fabricate TiO₂/Cu₂O core/shell heterojunction nanowire arrays (TiO₂/Cu₂O core/shell NWAs). When used as photoelectrode, the fabricated TiO₂/Cu₂O core/shell NWAs show improved photoelectrochemical (PEC) water splitting activity to pure TiO₂ NWAs. The effects of the CBD cycle times on the PEC activities have been studied. The TiO₂/Cu₂O core/shell heterojunction nanowire array photoelectrode prepared by cycling 5 times in the CBD process achieves the highest photocurrent of 2.5 mA cm^?2, which is 2.5 times higher than that of pure TiO₂ NWAs. In addition, the H₂ generation rate of this photoelectrode reaches to 32 μmol h^?1 cm^?2, 1.7 times higher than that of pure TiO₂ NWAs. Furthermore, the TiO₂/Cu₂O core/shell heterojunction nanowire array photoelectrode shows excellent photostability and achieves a stable photocurrent of over 2.3 mA cm^?2 during long light illumination time of 5 h. The enhanced photocatalytic activity of TiO₂/Cu₂O core/shell heterojunction nanowire array photoelectrode is attributed to the synergistic actions of TiO₂ and Cu₂O for improving visible light harvesting, and efficient transfer and separation of photogenerated electrons and holes.     

On the synthesis and photochemical studies of nanostructured TiO2 and TiO2 admixed VO2 photoelectrodes in regard to hydrogen production through photoelectrolysis

A new photoelectrode system TiO₂(ns)–VO₂ for photoassisted electrolysis of water is described. The nanostructured TiO₂ photoelectrode was prepared by the hydrolysis of titanium-tetraisopropoxide followed by deposition of thin film by spin coating. To prepare the TiO₂(ns)–VO₂ photoelectrode, vanadium film was deposited on the TiO₂(ns) film and subsequently oxidized in O₂ ambient. The TiO₂(ns)–VO₂ photoelectrode exhibited enhanced photovoltage and photocurrent of 680 mV and 11.0 mA cm⁻², respectively, whereas the TiO₂(ns) presented 540 mV and 3.2 mA cm⁻², respectively. X-ray and S.E.M studies were carried out to monitor the surface and bulk characteristics of the TiO₂(ns)–VO₂ photoelectrode. The rate of hydrogen production under photoelectrolysis was found to be 6 l h⁻¹ m⁻² for the TiO₂(ns) and ∼13.0 l h⁻¹ m⁻² for the TiO₂(ns)–VO₂ photoelectrode. The TiO₂(ns) photoelectrode shows the improvement in the PEC characteristics due to higher quantum yield resulting from the structured nature of the material. The PEC improvement in the TiO₂(ns)–VO₂ photoelectrode is due to the increase of range of absorption and the decrease of energy gap. © 1999 International Association for Hydrogen Energy. Published by Elsevier Science Ltd. All rights reserved.     

Nanostructured SrTiO3 thin films sensitized by Cu2O for photoelectrochemical hydrogen generation

We prepared nanostructured thin films of pristine SrTiO₃, Cu₂O and SrTiO₃/Cu₂O heterojunction with varying the thickness of Cu₂O. SrTiO₃ and Cu₂O thin films were deposited on ITO (Sn:In₂O₃) glass substrate using sol–gel spin-coating technique and spray pyrolysis method respectively. Samples were characterized using XRD (X-ray diffractometry), SEM (Scanning electron microscopy), and UV–Visible absorption spectroscopy. Nanostructured thin films of pristine SrTiO₃, Cu₂O and SrTiO₃/Cu₂O heterojunction systems were used as photoelectrode in the Photoelectrochemical (PEC) cell for water splitting reaction. Maximum photocurrent density value of 2.44 mA cm⁻² at 0.95 V/SCE were observed for SrTiO₃/Cu₂O heterojunction photoelectrode with 454 nm thickness, which was approximately 34 times higher than pristine SrTiO₃ thin film. Increased photocurrent density observed for the heterojunction can be attributed to the improved conductivity and better separation of the photogenerated charge carriers at the SrTiO₃/Cu₂O interface.     

Surface engineering of Ba-doped TiO2 nanorods by Bi2O3 passivation and (NiFe)OOH Co-catalyst layers for efficient and stable solar water oxidation

The rational design of heterostructures as an ideal photoelectrode system for H₂ and O₂ conversion in photoelectrochemical (PEC) system has been regarded as an essential key to boost PEC performance. In this work, to demonstrate the energetic photoanode cell, deposition of a thin layer of Bi₂O₃ is utilized to hybridize with the 5 wt% Ba-doped TiO₂ nanorod heterostructure under the cascading band diagram, where Ba-doping can enhance the charge transport/separation rate in bulk phase, in terms of increasing the donor density, enhancing the bulk electronic conductivity, and increasing the band bending. Furthermore, with optimizing the thickness (～15 nm) of Bi₂O₃, the (NiFe)OOH as a cocatalyst was adapted to improve the interfacial charge transfer rate in the PEC cell, reaching the high photocurrent density (J) of ～4.1 mA/cm² at 1.23 V (vs. Reversible Hydrogen Electrode) and stability retention of 100%, even after 15 h at 1 M NaOH under 1 Sun illumination condition. The improvement mainly comes from the extended absorption of visible light from the thin Bi₂O₃ layer, effective transfer/separation of photogenerated charge carriers, and acceleration of water oxidizing reaction, caused by the narrowed band gap and the favorable charge transfer under the cascading band alignment built by the heterojunction, as well as electrocatalyst, offering the timely consumption of photogenerated holes accumulated at the electrode surface.     

Mo-doped,Cr-Doped,and Mo–Cr codoped TiO2 thin-film photocatalysts by comparative sol-gel spin coating and ion implantation

Uniformly codoped anatase TiO₂ thin films of varying (equal) Mo and Cr concentrations (≤1.00 mol% for each dopant) were fabricated using sol-gel spin coating and deposited on fused silica substrates. All films were annealed at 450 °C for 2 h to recrystallise anatase. Undoped anatase films have been subjected to dual ion implantation for the first time, using Mo, Cr, and sequential Mo + Cr at 1 × 10¹⁴ atoms/cm². The films were characterised by GAXRD, AFM, SIMS, XPS, and UV–Vis and the performance was assessed by dye degradation. Despite the volumetric doping by sol-gel and the directional doping by ion implantation, neither method resulted in homogeneous dopant distributions. Both methods caused decreasing crystallinities and associated partial amorphisation. The XPS signal of the uniformly codoped films is dominated by undissolved dopant ions, which is not the case for the ion-implanted films. Increasing Ti valences are attributed to the fully oxidised condition of the Ti⁴⁺ ions that diffuse to the surface from Ti vacancy formation compared to the Ti valence of the bulk lattice, which contains Ti³⁺. Increasing O valence is attributed to the electronegativity of O^2?, which is higher than that of Ti⁴⁺. Detailed structural mechanisms for the solubility and energetics mechanisms involve the initial formation of Mo and Cr interstitials that fill the two voids adjacent to the central Ti ion in the TiO₆ octahedron, followed by integrated solid solubility (ISS) and intervalence/multivalence charge transfer (IVCT/MVCT). The sequential order of the last two is reversed for the two different doping methods. These two effects are likely to be the source of synergy, if any, between the two dopant ions. The photocatalytic performances of the uniformly codoped films are relatively poor and correlate well with the band gap (E_g). The performances of the ion-implanted films do not correlate with the E_g, where TiO₂–Mo performs poorly but TiO₂–Cr and TiO₂–Mo–Cr outperform the undoped film. These results are interpreted in terms of the competition between the effects of Mo doping, which causes partial amorphisation and/or blockage of active sites, and Cr doping, which may cause Mo–Cr synergism, Cr-based heterojunction formation, and/or improved charge-carrier separation owing to the surface-deposition nature of ion implantation.