Crystal structure and spectroscopic studies of NaGd(PO3)4

Single crystals of gadolinium–sodium polyphosphate NaGd(PO₃)₄ were grown for the first time using a flux method and characterized by X-ray diffraction. This phosphate crystallizes in a monoclinic system with P2₁/n space group and with the following unit-cell dimensions: a = 9.767(3) Å, b = 13.017(1) Å, c = 7.160(2) Å, β = 90.564(5)°, V = 910.3(4) Å³ and Z = 4. The crystal structure was solved from 3451 X-ray independent reflections with final R(F²) = 0.0219 and R_w(F²) = 0.056 refined with 164 parameters (). The atomic arrangement can be described as a long chain polyphosphate organization. Two infinite (PO₃)∝ chains with a period of eight tetrahedra run along the [0 1 1] direction. The structure of NaGd(PO₃)₄ consists of GdO₈ polyhedra sharing oxygen atoms with phosphoric group PO₄. Each Na⁺ ion is bonded to eight oxygen atoms.     

Structural and optical properties of (100 − x)(Li2B4O7) − x(SrO–Bi2O3–0.7Nb2O5–0.3V2O5) glasses and glass nanocrystal composites

Glasses of various compositions in the system (100 − x)(Li₂B₄O₇) − x(SrO–Bi₂O₃–0.7Nb₂O₅–0.3V₂O₅) (10  x  60, in molar ratio) were prepared by splat quenching technique. The glassy nature of the as-quenched samples was established by differential thermal analyses (DTA). The amorphous nature of the as-quenched glasses and crystallinity of glass nanocrystal composites were confirmed by X-ray powder diffraction studies. Glass composites comprising strontium bismuth niobate doped with vanadium (SrBi₂(Nb_0.7V_0.3)₂O_9−δ (SBVN)) nanocrystallites were obtained by controlled heat-treatment of the as-quenched glasses at 783 K for 6 h. High resolution transmission electron microscopy (HRTEM) of the glass nanocrystal composites (heat-treated at 783 K/6 h) confirm the presence of rod shaped crystallites of SBVN embedded in Li₂B₄O₇ glass matrix. The optical transmission spectra of these glasses and glass nanocrystal composites of various compositions were recorded in the wavelength range 190–900 nm. Various optical parameters such as optical band gap (E_opt), Urbach energy (ΔE), refractive index (n), optical dielectric constant and ratio of carrier concentration to the effective mass (N/m^*) were determined. The effects of composition of the glasses and glass nanocrystal composites on these parameters were studied.     

Synthesis and crystal structure of [2-NH2-5-CH3C5H4N]4P4O12·6H2O

Chemical preparation, crystal structure, IR absorption and thermal analysis of a new cyclotetraphosphate [2-NH₂-5-CH₃C₅H₄N]₄P₄O₁₂·6H₂O are reported. This compound is triclinic P-1 with unit-cell parameters: a = 10.206(5), b = 11.778(1), c = 9.991(4) Å,  = 110.40(6), β = 117.74(6), γ = 86.41(3)°, V = 989.1(8) Å³, Z = 1, D_x = 1.445 g cm⁻³. The structure has been determined and refined to R = 0.034 and R_w = 0.044, using 3663 independent reflections. The ring anions and water molecules form layers spreading around (a, b + c) planes via OHO hydrogen bonds. Between them are anchored 2-amino-5-methylpyridium cations, which establish H-bonds to interconnect the different adjacent layers and so contribute to the cohesion of the three-dimensional network. Tautomerization of (C₆H₉N₂)⁺ groups was evidenced in the present structure.     

Synthesis, structure refinement and characterization of tetrahydrated acid gadolinium diphosphate HGdP2O7·4H2O

Synthesis and single crystal structure are reported for a new gadolinium acid diphosphate tetrahydrate HGdP₂O₇·4H₂O. This salt crystallizes in the monoclinic system, space group P2₁/n, with the following unit-cell parameters: a = 6.6137(2) Å, b = 11.4954(4) Å, c = 11.377(4) Å, β = 87.53(2)° and Z = 4. Its crystal structure was refined to R = 0.0333 using 1783 reflections. The corresponding atomic arrangement can be described as an alternation of corrugated layers of monohydrogendiphosphate groups and GdO₈ polyhedra parallel to the () plane. The cohesion between the different diphosphoric groups is provided by strong hydrogen bonding involving the W4 water molecule.

IR and Raman spectra of HGdP₂O₇·4H₂O confirm the existence of the characteristic bands of diphosphate group in 980–700 cm⁻¹ area. The IR spectrum reveals also the characteristic bands of water molecules vibration (3600–3230 cm⁻¹) and acidic hydrogen ones (2340 cm⁻¹). TG and DTA investigations show that the dehydration of this salt occurs between 79 and 900 °C. It decomposes after dehydration into an amorphous phase. Gadolinium diphosphate Gd₄(P₂O₇)₃ was obtained by heating HGdP₂O₇·4H₂O in a static air furnace at 850 °C for 48 h.     

Crystal growth and spectral properties of pure and Co-doped Mg3B2O6 crystal

Novel pure and cobalt-doped magnesium borate crystals (Mg₃B₂O₆) have been grown successfully by the Czochralski technique for the first time. Crystal growth, X-ray powder diffraction (XRD) analysis, absorption spectrum, fluorescence spectrum as well as fluorescence decay curve of Co²⁺:Mg₃B₂O₆ (MBO) were described. From the absorption peaks for the octahedral Co²⁺ ions, the crystal-field parameter Dq and the Racah parameter B were estimated to be 943.3 cm⁻¹ and 821.6 cm⁻¹, respectively. The fluorescence lifetime of the transition ⁴T₁(⁴P) → ⁴T₂ centered at 717 nm was measured to be 9.68 ms.     

Optical properties of Nd:NaLa (WO4)2 single crystal

Nd³⁺-doped NaLa(WO₄)₂ single crystal with a dimension of 20 mm × 40 mm and a good optical quality was grown by Czochralski method. The polarized absorption spectra and emission spectra were measured at room temperature. The absorption cross-section and emission cross-section were presented. The Judd–Ofelt theory, extended to anisotropic system, has been applied to evaluate the intensity parameters Ω_t (t = 2, 4, 6), radiative transition rates A, radiative lifetimes τ_R and fluorescent branching ratios β. The calculated radiative lifetime was compared with the experiment data for the ⁴F_3/2 emitting level. All spectral features are strongly affected by an inhomogeneous broadening connected with the ‘disordered crystal’ character of the title compound.     

Reaction between the tetragonal tungsten bronze niobate K2Sr4Nb10O30 and the perovskite Pb(Mg1/3Nb2/3)O3

The search for dielectric materials with a high dielectric constant and ′_r = ƒ(T) curves with a flat profile fitting the X7R specification is still ongoing. Promising results were obtained by mixing compounds with closely related structures, such as the tetragonal tungsten bronze (TTB) niobate K₂Sr₄Nb₁₀O₃₀ and the perovskite Pb(Mg_1/3Nb_2/3)O₃ (PMN). The present study, based on three methods of synthesis, explores the origin of the spreading out of the dielectric curves ′_r = ƒ(T). For the composition 10x K_0.2Sr_0.4NbO₃ (KSN) + (1 − x)Pb(Mg_1/3Nb_2/3)O₃ (PMN) with x = 0.3–0.6, the three synthesis methods provided similar characteristics and for the highest perovskite ratio (x = 0.3), the ′_r = ƒ(T) curve exhibits a flat profile. When lithium is used as a sintering agent, ′_r = ƒ(T) curves present a linear dependency with the temperature. These materials are also characterized by a structural and a microstructural inhomogeneity. Two phases TTB and perovskite type, different from KSN and PMN, are present after calcination and sintering, but not evenly distributed. The PbO loss during sintering also contributes to the evolution of the properties of the material.     

Effect of heat treatment on photoluminescence behavior of BaMgAl10O17:Eu phosphors

The blue phosphor of BaMgAl₁₀O₁₇:Eu²⁺ (BAM) powders were prepared by solid-state reaction. The thermal degradation of BAM phosphor significantly reduces the intensity of the blue emission. BAM is reduced by an amount of 50% after heating at around 800 °C for 1 h. Photoluminescence (PL) excitation and emission spectra showed that the blue emission of 450 nm peak decreased with increasing annealing temperature. The ⁵D₀→⁷F₁ and ⁵D₀→⁷F₂ transition of Eu³⁺ were observed at 590 and 615 nm emission lines over 1100 °C. Electron paramagnetic resonance (EPR) spectrum also detected two signals of Eu²⁺, corresponding to g=3.7156(9) for 88 mT, and g=2.9507(9) for 133 mT. X-ray absorption near edge structure (XANES) spectrum decreased the intensity of Eu²⁺ for 6977 eV with increasing annealing temperature, while high-energy peak of Eu³⁺ for 6984 eV was increased. The combined use of X-ray and neutron data by the Rietveld refinement appears to support that the secondary phase of EuMgAl₁₁O₁₉ magnetoplumbite structure in BAM may be formed by heat treatment.     

Crystal structure, thermal analysis and IR spectroscopic investigation of (C6H9N2)H2XO4 (X = As, P)

Crystals of 2-amino-4-methylpyridinium dihydrogenmonoarsenate (C₆H₉N₂)H₂AsO₄ and 2-amino-4-methylpyridinium dihydrogenmonophosphate (C₆H₉N₂)H₂PO₄ have been prepared and grown at room temperature. These materials are isotypic with the following unit cell dimensions (C₆H₉N₂)H₂AsO₄: a = 12.4415(5) Å, b = 6.8224(3) Å, c = 11.3524(5) Å, Z = 4, V = 963.60(6) Å³; (C₆H₉N₂)H₂PO₄: a = 12.4410(9) Å, b = 6.7165(3) Å, c = 11.3417(5) Å, Z = 4, V = 925.09(10) Å³. The common space group is Pnma. The structure of these compounds has been determined by X-ray data collection on single crystals of (C₆H₉N₂)H₂AsO₄ and (C₆H₉N₂)H₂PO₄. Due to the strong hydrogen-bond network connecting the H₂XO₄ groups, the anionic arrangement must be described as a linear organization. The chains composed by the macroanion spread along the b-direction, approximately centered by x = 0 and 1/2. All atoms of the structure, except one oxygen atom, are located in the mirror planes situated at y = 1/4 and 3/4, imparting an internal mirror symmetry to the anionic and the cationic entities. The linear macroanions are crossed by organic cations lying in mirrors perpendicular to the b-direction; this atomic arrangement is then described by a three-dimensional network of hydrogen bonds, built up by two types, O–HO bonds inside the chains and N–HO bonds linking adjacent chains. The thermal properties of both compounds are investigated as well as the IR properties supported by group theoretical analyses.     

Crystal structure and characterization of [2,5-(CH3O)2C6H3NH3]4P4O12·2H2O

The preparation, crystal structure, TG–DTA analysis and spectroscopy investigation are reported for the 2,5-dimethoxy phenyl ammonium cyclotetraphosphate dihydrate [2,5-(CH₃O)₂C₆H₃NH₃]₄P₄O₁₂·2H₂O. This new compound is triclinic P with unit cell dimensions: a = 7.438(5) Å, b = 11.841(7) Å, c = 12.354(4) Å,  = 96.61(4)°, β = 98.35(4)°, γ = 102.60(6)°, Z = 1 and V = 1038.0(1) Å³. Its crystal structure has been determined and refined to R = 0.049, with 5128 independant reflections. The structure can be described by rows of P₄O₁₂ ring anions along the a axis; between these rows are located the organic groups, connected to them by hydrogen bonds.     

Growth kinetics of Mo3Si layer in the Mo5Si3/Mo diffusion couple

The diffusion processes and growth kinetics of the Mo₃Si silicide layer occurring at annealing the Mo₅Si₃/Mo diffusion couple between 1180 and 1800 °C were studied by electrothermography. The experimental results are supplemented with calculations on the behaviour of the initial Mo₅Si₃/Mo diffusion couple on the basis of the reaction diffusion model describing the transformation of the Mo₅Si₃ layer into a Mo₃Si one. The values of the parabolic growth constant for Mo₃Si layer were determined and the silicon diffusion coefficient in the Mo₃Si phase was calculated: D = 0.165 exp[(− 247 ± 10) / RT], cm²/s, where the activation energy is expressed in terms of kJ/mol.     

Effect of CeO2 addition on structure and electrical properties of (Na0.5Bi0.5)0.93Ba0.07TiO3 ceramics prepared by citric method

(Na_0.5Bi_0.5)_0.93Ba_0.07TiO₃ ceramics added with 0–0.8 wt.% CeO₂ were prepared by a citrate method, and the influence of the CeO₂ addition on the structure and electrical properties was investigated. The specimens containing various amounts of CeO₂ show the coexistence of rhombohedral and tetragonal phases, with the relative content of the tetragonal phases gradually enhancing with increasing amount of CeO₂. Compared with (Na_0.5Bi_0.5)_0.93Ba_0.07TiO₃, the specimen added with a small amount of CeO₂ (≤0.2 wt.%) display a slightly improved electromechanical coupling factor (k_p) and piezoelectric constant (d₃₃) in conjunction with a reduced dielectric loss (tg δ) and an enhanced mechanical quality factor (Q_m), while higher CeO₂ amounts led to a rapid deterioration of the piezoelectric and ferroelectric properties. The variation of the electrical properties with the CeO₂ addition was tentatively interpreted with respect to doping effect, crystal-structural evolution and stability of ferroelectric domains.     

Nanocrystallization of SrBi2Nb2O9 from glasses in the system Li2B4O7---SrO---Bi2O3---Nb2O5

Transparent glasses in the system (100−x)Li₂B₄O₇–x(SrO---Bi₂O₃---Nb₂O₅) (10≤x≤60) (in molar ratio) were fabricated by a conventional melt-quenching technique. Amorphous and glassy characteristics of the as-quenched samples were established via X-ray powder diffraction (XRD) and differential thermal analyses (DTA) respectively. Glass–ceramics embedded with strontium bismuth niobate, SrBi₂Nb₂O₉ (SBN) nanocrystals were produced by heat-treating the as-quenched glasses at temperatures higher than 500 °C. Perovskite SBN phase formation through an intermediate fluorite phase in the glass matrix was confirmed by XRD and transmission electron microscopy (TEM). Infrared and Raman spectroscopic studies corroborate the observation of fluorite phase formation. The dielectric constant (_r) and the loss factor (D) for the lithium borate, Li₂B₄O₇ (LBO) glass comprising randomly oriented SBN nanocrystals were determined and compared with those predicted based on the various dielectric mixture rule formalism. The dielectric constant was found to increase with increasing SBN content in LBO glass matrix.     

First principles calculations of thermal equations of state and thermodynamical properties of MgH2 at finite temperatures

We present the first principles calculations of the thermodynamical properties of magnesium hydride (MgH₂) over a temperature range of 0–1000 K. The phonon dispersions are determined within the density functional framework and are used to calculate the free energy of MgH₂ within the quasiharmonic approximation (QHA) at each cell volume and temperature T. Using the free energies the thermal equation of state (EOS) is derived at several temperatures. From the thermal EOS structural parameters such as the equilibrium cell volume (V₀) and elastic properties, namely, bulk modulus (K₀) and its pressure derivative are computed. The free energies are also used to calculate various thermodynamical properties within QHA. These include internal energy E, entropy S, specific heat capacity at constant pressure C_P, thermal pressure P_thermal(V, T) and volume thermal expansion ΔV/V (%). The good agreement of calculated values of S and C_P with experimental data exhibits that QHA can be used as a tool for calculating the thermodynamical properties of MgH₂ over a wide temperature range. P_thermal(V,T) increases strongly with T at all the volumes but it is a slowly varying function of volume for T = 298–500 K. According to Karki [B.B. Karki, Am. Miner. 85 (2000) 1447] such volume based variations can be neglected and so it is possible to estimate the thermal EOS only with the knowledge of the measured P_thermal(V, T) versus temperature at ambient pressure and isothermal compression data at ambient temperature. Temperature dependence of ΔV/V(%) shows that V₀ increased with increase in temperature. However, the percentage decrease in K₀ superseded this percentage increase in V₀ even at temperatures moderately higher than 298 K. Therefore, we suggest application of temperature (T > 298 K) as an approach to enhance the hydrogen storage capacity of MgH₂ because of its better compressibility at these temperatures.     

Powder X-ray diffraction, infrared and conductivity studies of AgSbMP3O12 (M = Al, Ga, Fe and Cr)

New Nasicon type of compounds of composition AgSbMP₃O₁₂ (M = Al, Ga, Fe and Cr) are synthesized by solid-state method. All the compounds crystallize in the hexagonal lattice with space group . The infrared spectra of these compounds show characteristic bands due to PO₄ group. The frequency independent conductivity of these compounds shows Arrhenius type behavior and the activation energy for conduction is in the range 0.40–0.55 eV. Frequency independent conductivity (σ_dc) studies and frequency dependent (σ_ac) impedance measurements correlate well. The Cole–Cole plots do not show any spikes on the lower frequency side indicating negligible electrode effects. The activation energies obtained from the plots of log σ_dcT versus 1/T, log σ_ac(0) versus 1/T and log τ versus 1/T are approximately the same. The peak width at half height for electric modulus (M″) plot is 1.24 decades for all samples, which is close to 1.14 decades observed for Debye solid. The height of electric modulus (M″) obtained from the experimental plots are close to that of M″ (max) = C₀/2C indicating the Debye nature of the samples.     

Preparation and optical properties of sol–gel derived Er-doped Al2O3–Ta2O5 films

Thin films of the system xAl₂O₃–(100 − x)Ta₂O₅–1Er₂O₃ were prepared by a sol–gel method and a dip-coating technique. The influences of the composition and the crystallization of the films on Er³⁺ optical properties were investigated. Results of X-ray diffraction indicated that the crystallization temperature of Ta₂O₅ increased from 800 to 1000 °C with increased values of x. In crystallized films, the intensities of the visible fluorescence and upconversion fluorescence tend to decrease with an increase in x values, due to the high phonon energy of Al₂O₃; the strongest fluorescence is observed in a crystallized film for x = 4 heat treated at 1000 °C. In amorphous films obtained by heat treatment at relatively low temperatures the Er³⁺ fluorescence could not be observed because strong fluorescence from organic residues remaining in the films thoroughly covered the Er³⁺ fluorescence. On the other hand, the Er³⁺ upconversion fluorescence in the amorphous films was observed to be stronger than that in the crystallized films. The strongest upconversion fluorescence is observed in an amorphous film for x = 75 heat treated at 800 °C.     

Pyroelectric properties of BST/PLT composite thick films with addition of xPbO–(1 − x)B2O3 glass

The Ba_xSr_1−xTiO₃ (BST)/Pb_1−xLa_xTiO₃ (PLT) composite thick films (20 μm) with 12 mol% amount of xPbO–(1 − x)B₂O₃ glass additives (x = 0.2, 0.35, 0.5, 0.65 and 0.8) have been prepared by screen-printing the paste onto the alumina substrates with silver bottom electrode. X-ray diffraction (XRD), scanning electron microscope (SEM) and an impedance analyzer and an electrometer were used to analyze the phase structures, morphologies and dielectric and pyroelectric properties of the composite thick films, respectively. The wetting and infiltration of the liquid phase on the particles results in the densification of the composite thick films sintered at 750 °C. Nice porous structure formed in the composite thick films with xPbO–(1 − x)B₂O₃ glass as the PbO content (x) is 0.5 ≥ x ≥ 0.35, while dense structure formed in these thick films as the PbO content (x) is 0.8 ≥ x ≥ 0.65. The volatilization of the PbO in PLT and the interdiffusion between the PLT and the glass lead to the reduction of the c-axis of the PLT phase. The operating temperature range of our composite thick films is 0–200 °C. At room temperature (20 °C), the BST/PLT composite thick films with 0.35PbO–0.65B₂O₃ glass additives provided low heat capacity and good pyroelectric figure-of-merit because of their porous structure. The pyroelectric coefficient and figure-of-merit F_D are 364 μC/(m² K) and 14.3 μPa^−1/2, respectively. These good pyroelectric properties as well as being able to produce low-cost devices make this kind of thick films a promising candidate for high-performance pyroelectric applications.     

Optical properties of Tl2InGaS4 layered single crystal

The temperature dependence of the optical band gap of Tl₂InGaS₄ single crystal in the temperature region of 300–500 K and the room temperature refractive index, n(λ), have been investigated. The absorption coefficient, which was calculated from the transmittance and reflectance spectra in the incident photon energy range of 2.28–2.48 eV, increased with increasing temperature. Consistently, the absorption edge shifts to lower energy values as temperature increases. The fundamental absorption edge corresponds to an indirect allowed transitions energy gap (2.35 eV) that exhibits a temperature coefficient of −4.03 × 10⁻⁴ eV/K. The room temperature n(λ), calculated from the reflectance and transmittance data, allowed the identification of the oscillator strength and energy, static and lattice dielectric constants, and static refractive index as 16.78 eV and 3.38 eV, 5.96 and 11.77, and 2.43, respectively.     

Formation and control of zinc nitride in a molten LiCl–KCl–Li3N system

We investigated a possibility of electrochemical formation and control of zinc nitride in a molten LiCl–KCl–Li₃N system at 673 K. Zinc nitride films were obtained by means of potentiostatic electrolysis of zinc electrodes in the melt. From XRD analysis, it was confirmed that obtained films consisted of Zn₃N₂ and LiZnN and that the composition of each film was effected by the applied potential value. In the potential range from 0.75 to 1.6 V (versus Li⁺/Li), the ratio of Zn₃N₂ increased as the applied potential was more positive. Based on the result, we achieved the formation of Zn₃N₂ film (3–5 μm) in anti-scandium oxide structure (a = 0.977 nm) by means of potentiostatic electrolysis at 1.6 V for 3 h.     

Synthesis of MoSi2–Al2O3 nanocomposite by mechanical alloying

MoSi₂–Al₂O₃ nanocomposite was synthesized by mechanical alloying (MA) of MoO₃, SiO₂ and Al powder mixture. The structural evolution of the powders was studied by X-ray diffraction (XRD). Both β-MoSi₂ and -MoSi₂ were obtained after 3 h of milling. The spontaneous formation of β-MoSi₂ during milling proceeded by a mechanically induced self propagating reaction (MSR), analogous to that of the self propagating high temperature synthesis (SHS). After 70 h of milling the β-phase transformed to -phase. The crystallite size of -MoSi₂ and Al₂O₃ after milling for 100 h was 12 and 17 nm, respectively. Residual Mo and Si in the 3 and 70 h milled samples formed β-MoSi₂ and Mo₅Si₃ during heating at 1000 °C, respectively.