Synthesis and transport properties in La2−xAxMo2O9−δ (A = Ca, Sr, Ba, K) series

The La_2−xA_xMo₂O_9−δ (A = Ca²⁺, Sr²⁺, Ba²⁺ and K⁺) series has been synthesised as nanocrystalline materials via a modification of the freeze-drying method. The resulting materials have been characterised by X-ray diffraction (XRD), thermal analysis (TG/DTA, DSC), scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM). The high-temperature β-polymorph is stabilised for dopant content x > 0.01. The nanocrystalline powders were used to obtain dense ceramic materials with optimised microstructure and relative density >95%. The overall conductivity determined by impedance spectroscopy depends on both the ionic radius and dopant content. The conductivity decreases slightly as the dopant content increases in addition a maximum conductivity value was found for Sr²⁺ substitution, which show an ionic radii slightly higher than La³⁺ (e.g. 0.08 S cm⁻¹ for La₂Mo₂O₉ and 0.06 S cm⁻¹ for La_1.9Sr_0.1Mo₂O_9−δ at 973 K). The creation of extrinsic vacancies upon substitution results in a wider stability range under reducing conditions and prevents amorphisation, although the stability is not enhanced significantly when compared to samples with higher tungsten content. These materials present high thermal expansion coefficients in the range of (13-16) × 10⁻⁶ K⁻¹ between room temperature and 753 K and (18-20) × 10⁻⁶ K⁻¹ above 823 K. The ionic transport numbers determined by a modified emf method remain above 0.98 under an oxygen partial pressure gradient of O₂/air and decreases substantially under wet 5% H₂-Ar/air when approaching to the degradation temperature above 973 K due to an increase of the electronic contribution to the overall conductivity.     

Ionic and electronic transport in stabilized β-La2Mo2O9 electrolytes

Increasing temperature from 973 to 1173 K leads to a substantial increase of the electronic contribution to the total conductivity of undoped lanthanum molybdate and La₂Mo₂O₉-based solid electrolytes, including La₂Mo_1.7W_0.3O₉, La₂Mo_1.95V_0.05O₉ and La_1.7Bi_0.3Mo₂O₉, where the stabilization of β-La₂Mo₂O₉ down to room temperature was confirmed by high-resolution X-ray diffraction (XRD) and differential scanning calorimetry (DSC) data. In air, the ion transference numbers determined by the modified Faradaic efficiency (FE) technique, decrease from 0.991-0.997 at 973-1023 K down to 0.977-0.984 at 1173 K. Reducing oxygen partial pressure also increases electronic conduction evaluated by the emf and oxygen permeability (OP) measurements, which indicates that the electronic transport is n-type, resulting from decreasing oxygen content in the molybdate lattice. The level of n-type electronic conductivity in air is quite similar for all La₂Mo₂O₉-based ceramics. The results show that these materials can be used as solid electrolytes only under oxidizing conditions and only at temperatures below 1073 K. Their practical applications may also be complicated due to relatively high thermal expansion coefficients (CTEs), (14.1-14.8)×10⁻⁶ K⁻¹ at 300-700 K and (16.4-22.5)×10⁻⁶ K⁻¹ at 850-1070 K, which are close to those of stabilized δ-Bi₂O₃ and γ-Bi₂VO_5.5 electrolytes.     

Synthesis and tunable thermal expansion properties of Sc2−xYxW3O12 solid solutions

A new series of rare earth solid solutions Sc_2−xY_xW₃O₁₂ was successfully synthesized by the conventional solid-state method. Effects of doping ion yttrium on the crystal structure, morphology and thermal expansion property of as-prepared Sc_2−xY_xW₃O₁₂ ceramics were investigated by X-ray diffraction (XRD), thermogravimetric analysis (TG), field emission scanning electron microscope (FE-SEM) and thermal mechanical analyzer (TMA). Results indicate that the obtained Sc_2−xY_xW₃O₁₂ samples with Y doping of 0≤x≤0.5 are in the form of orthorhombic Sc₂W₃O₁₂-structure and show negative thermal expansion (NTE) from room temperature to 600 °C; while as-synthesized materials with Y doping of 1.5≤x≤2 take hygroscopic Y₂W₃O₁₂·nH₂O-structure at room temperature and exhibit NTE only after losing water molecules. It is suggested that the obvious difference in crystal structure leads to different thermal expansion behaviors in Sc_2−xY_xW₃O₁₂. Thus it is proposed that thermal expansion properties of Sc_2−xY_xW₃O₁₂ can be adjusted by the employment of Y dopant; the obtained Sc_1.5Y_0.5W₃O₁₂ ceramic shows almost zero thermal expansion and its average linear thermal expansion coefficient is −0.00683×10⁻⁶ °C⁻¹ in the 25–250 °C range.     

Synthesis and negative thermal expansion property of Y2−xLaxW3O12 (0≤x≤2)

Y_2−xLa_xW₃O₁₂ solid solutions were successfully synthesized by the solid state reaction method. The microstructure, hygroscopicity and thermal expansion property of the resulting samples were investigated by X-ray diffraction (XRD), thermogravimetric analysis (TGA), field emission scanning electron microscopy (FESEM) and thermal mechanical analysis (TMA). Results indicate that the structural phase transition of the Y_2−xLa_xW₃O₁₂ changes from orthorhombic to monoclinic with increasing substituted content of lanthanum. The pure phase can form for 0≤x≤0.4 with orthorhombic structure and for 1.5≤x≤2 with monoclinic one. High lanthanum content leads to a low relative density of Y_2−xLa_xW₃O₁₂ ceramic. Thermal expansion coefficients of the Y_2−xLa_xW₃O₁₂ (0≤x≤2) ceramics also vary from −9.59×10⁻⁶ K⁻¹ to 2.06×10⁻⁶ K⁻¹ with increasing substituted content of lanthanum. The obtained Y_0.25La_1.75W₃O₁₂ ceramic shows almost zero thermal expansion and its average linear thermal expansion coefficient is −0.66×10⁻⁶ K⁻¹ from 103 °C to 700 °C.     

Synthesis and thermal expansion properties of Y2−xLaxMo3O12 (x=0, 0.5, 2)

Y_2−xLa_xMo₃O₁₂ (x=0, 0.5, 2) ceramics were successfully synthesized by the solid state reaction method. The microstructure, composition and thermal expansion property of the resulting samples were investigated by X-ray diffraction (XRD), thermogravimetric analysis (TGA), field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS) and dilatometry. Results indicate that the Y_1.5La_0.5Mo₃O₁₂ crystallizes in monoclinic Tb₂Mo₃O₁₂-type structure and it is non-hygroscopic. The Y_1.5La_0.5Mo₃O₁₂ ceramic is denser than the Y₂Mo₃O₁₂ and La₂Mo₃O₁₂ ceramics, and its relative density can reach 94.12% of the theoretical value. Most importantly, it shows almost zero thermal expansion and its thermal coefficient is 0.87×10⁻⁶ K⁻¹ from 178 °C to 600 °C. Y₂Mo₃O₁₂ ceramic shows negative thermal expansion whereas La₂Mo₃O₁₂ ceramic shows positive thermal expansion, their thermal expansion coefficients being−12.06×10⁻⁶ K⁻¹ and 8.88×10⁻⁶×10⁻⁶ K⁻¹, respectively.     

Preparation, characterization and electrical conductivity studies of NdYb1−xGdxZr2O7 (0 ≤ x ≤ 1.0) ceramics

Several compositions of NdYb_1−xGd_xZr₂O₇ (0 ≤ x ≤ 1.0) ceramics were prepared by pressureless-sintering method at 1973 K for 10 h in air. The relative density, microstructure and electrical conductivity of NdYb_1−xGd_xZr₂O₇ ceramics were analyzed by the Archimedes method, X-ray diffraction, scanning electron microscopy and impedance plots measurements. NdYb_1−xGd_xZr₂O₇ (0 ≤ x ≤ 0.3) ceramics have a single phase of defect fluorite-type structure, and NdYb_1−xGd_xZr₂O₇ (0.7 ≤ x ≤ 1.0) ceramics exhibit a single phase of pyrochlore-type structure; however, the NdYb_0.5Gd_0.5Zr₂O₇ composition shows mixed phases of both defect fluorite-type and pyrochlore-type structures. The measured values of the grain conductivity obey the Arrhenius relation. The grain conductivity of each composition in NdYb_1−xGd_xZr₂O₇ ceramics gradually increases with increasing temperature from 673 to 1173 K. NdYb_1−xGd_xZr₂O₇ ceramics are oxide-ion conductor in the oxygen partial pressure range of 1.0 × 10⁻⁴ to 1.0 atm at all test temperature levels. The highest grain conductivity value obtained in this work is 1.79 × 10⁻² S cm⁻¹ at 1173 K for NdYb_0.3Gd_0.7Zr₂O₇ composition.     

Zr-doped Li[Ni0.5−xMn0.5−xZr2x]O2 (x = 0, 0.025) as cathode material for lithium ion batteries

Layered Li[Ni_0.5−xMn_0.5−xZr_2x]O₂ (x = 0, 0.025) have been prepared by the mixed hydroxide and molten-salt synthesis method. The individual particles of synthesized materials have a sub-microsize range of 200-500 nm, and LiNi_0.475Mn_0.475Zr_0.05O₂ has a rougher surface than that of LiNi_0.5Mn_0.5O₂. The Li/Li[Ni_0.5−xMn_0.5−xZr_2x]O₂ (x = 0, 0.025) electrodes were cycled between 4.5 and 2.0 V at a current density of 15 mA/g, the discharge capacity of both cells increased during the first ten cycles. The discharge capacity of the Li/LiNi_0.475Mn_0.475Zr_0.05O₂ cell increased from 150 to 220 mAh/g, which is 50 mAh/g larger than that of the Li/LiNi_0.5Mn_0.5O₂ cell. We found that the oxidation of oxygen and the Mn³⁺ ion concerned this phenomenon from the cyclic voltammetry (CV). Thermal stability of the charged Li[Ni_0.5−xMn_0.5−xZr_2x]O₂ (x = 0, 0.025) cathode was improved by Zr doping.     

Preparation and characterization of novel spinel Li4Ti5O12−xBrx anode materials

Br-doped Li₄Ti₅O₁₂ in the form of Li₄Ti₅O_12−xBr_x (0 ≤ x ≤ 0.3) compounds were successfully synthesized via solid state reaction. The structure and electrochemical properties of the spinel Li₄Ti₅O_12−xBr_x (0 ≤ x ≤ 0.3) materials were investigated. The Li₄Ti₅O_12−xBr_x (x = 0.2) presents the best discharge capacity among all the samples, and shows better reversibility and higher cyclic stability compared with pristine Li₄Ti₅O₁₂, especially at high current rates. When the discharge rate was 0.5 C, the Li₄Ti₅O_12−xBr_x (x = 0.2) sample presented the excellent discharge capacity of 172 mAh g⁻¹, which was very close to its theoretical capacity (175 mAh g⁻¹), while that of the pristine Li₄Ti₅O₁₂ was 123.2 mAh g⁻¹ only.     

Study on the rapid synthesis of LiNi1−xCoxO2 cathode material for lithium secondary battery

LiNi_1−xCo_xO₂ (x = 0, 0.1, 0.2) cathode materials were successfully synthesized by a rheological phase reaction method with calcination time of 0.5 h at 800 °C. All obtained powders are pure phase with α-NaFeO₂ structure (R-3m space group). The samples deliver an initial discharge capacity of 182, 199 and 189 mAh g⁻¹ (25 mA g⁻¹, 4.35-3.0 V), respectively. The reaction mechanism was also discussed, which consists of a series of defect reactions. As a result of these defect reactions, the reaction of forming LiNi_1−xCo_xO₂ takes place in high speed.     

Electrochemical properties of La1−xSrxFeO3 (x = 0.2, 0.4) as negative electrode of Ni-MH batteries

La_(1−x)Sr_xFeO₃ (x = 0.2,0.4) powders were prepared by a stearic acid combustion method, and their phase structure and electrochemical properties were investigated systematically. X-ray diffraction (XRD) analysis shows that La_(1−x)Sr_xFeO₃ perovskite-type oxides consist of single-phase orthorhombic structure (x = 0.2) and rhombohedral one (x = 0.4), respectively. The electrochemical test shows that the reaction at La_(1−x)Sr_xFeO₃ oxide electrodes are reversible. The discharge capacities of La_(1−x)Sr_xFeO₃ oxide electrodes increase as the temperature rises. With the increase of the temperature from 298 K to 333 K, their initial discharge capacity mounts up from 324.4 mA h g⁻¹ to 543.0 mA h g⁻¹ (when x = 0.2) and from 147.0 mA h g⁻¹ to 501.5 mA h g⁻¹ (when x = 0.4) at the current density of 31.25 mA g⁻¹, respectively. After 20 charge-discharge cycles, they still remain perovskite-type structure. Being similar to the relationship between the discharge capacity and the temperature, the electrochemical kinetic analysis indicates that the exchange current density and proton diffusion coefficient of La_(1−x)Sr_xFeO₃ oxide electrodes increase with the increase of the temperature. Compared with La_0.8Sr_0.2FeO₃, La_0.6Sr_0.4FeO₃ electrode is a more promising candidate for electrochemical hydrogen storage because of its higher cycle capacity at various temperatures.     

Effects of B-site ion (M) substitution on the ionic conductivity of (Li3xLa2/3−x)1+y/2(MyTi1−y)O3 (M=Al, Cr)

Effect on the ionic conductivity of B-site ion (M) substitution in (Li_3xLa_2/3−x)_1+y/2M_yTi_1−yO₃ (M=Al, Cr) has been investigated. It has been found that partial substitution of smaller Al³⁺ for Ti⁴⁺ is effective to enhance the ionic conductivity of Li_3xLa_2/3−xTiO₃. At 300 K, the maximum bulk conductivity of (1.58±0.01)×10⁻³ S cm⁻¹ is observed from the composition of (Li_0.39La_0.54)_1−y/2Al_yTi_1−yO₃ with y=0.02 (x=0.13), that is the highest yet reported for known perovskite solutions at room temperature. The conductivity enhancement is interpreted as being due to the substitution-induced bond-strength change rather than due to bottleneck size change for Li migration, TiO₆-octahedron tilting or A-site cation ordering.     

Structural and electrochemical behaviors of metastable Li2/3[Ni1/3Mn2/3]O2 modified by metal element substitution

Layered metastable lithium manganese oxides, Li_2/3[Ni_1/3−xMn_2/3−yM_x+y]O₂ (x = y = 1/36 for M = Al, Co, and Fe and x = 2/36, y = 0 for M = Mg) were prepared by the ion exchange of Li for Na in P2-Na_2/3[Ni_1/3−xMn_2/3−yM_x+y]O₂ precursors. The Al and Co doping produced the T^#2 structure with the space group Cmca. On the other hand, the Fe and Mg doped samples had the O6 structure with space group R-3m. Electron diffraction revealed the 1:2 type ordering within the Ni_1/3−xMn_2/3−yM_x+yO₂ slab. It was found that the stacking sequence and electrochemical performance of the Li cells containing T^#2-Li_2/3[Ni_1/3Mn_2/3]O₂ were affected by the doping with small amounts of Al, Co, Fe, and Mg. The discharge capacity of the Al doped sample was around 200 mAh g⁻¹ in the voltage range between 2.0 and 4.7 V at the current density of 14.4 mA g⁻¹ along with a good capacity retention. Moreover, for the Al and Co doped and undoped oxides, the irreversible phase transition of the T^#2 into the O2 structure was observed during the initial lithium deintercalation.     

Electrochemical and thermal studies of Li[NixLi(1/3−2x/3)Mn(2/3−x/3)]O2 (x = 1/12, 1/4, 5/12, and 1/2)

Samples of the layered cathode materials, Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ (x = 1/12, 1/4, 5/12, and 1/2), were synthesized at 900 °C. Electrodes of these samples were charged in Li-ion coin cells to remove lithium. The charged electrode materials were rinsed to remove the electrolyte salt and then added, along with EC/DEC solvent or 1 M LiPF₆ EC/DEC, to stainless steel accelerating rate calorimetry (ARC) sample holders that were then welded closed. The reactivity of the samples with electrolyte was probed at two states of charge. First, for samples charged to near 4.45 V and second, for samples charged to 4.8 V, corresponding to removal of all mobile lithium from the samples and also concomitant release of oxygen in a plateau near 4.5 V. Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples with x = 1/4, 5/12 and 1/2 charged to 4.45 V do not react appreciably till 190 °C in EC/DEC. Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples charged to 4.8 V versus Li, across the oxygen release plateau, start to significantly react with EC/DEC at about 130 °C. However, their high reactivity is similar to that of Li_0.5CoO₂ (4.2 V) with 1 μm particle size. Therefore, Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples showing specific capacity of up to 225 mAh/g may be acceptable for replacing LiCoO₂ (145 mAh/g to 4.2 V) from a safety point of view, if their particle size is increased.     

Polypyrrole and La1−xSrxMnO3 (0≤ x ≤0.4) composite electrodes for electroreduction of oxygen in alkaline medium

Composite G/PPy/PPy(La_1−xSr_xMnO₃)/PPy electrodes made of the perovskite La_1−xSr_xMnO₃ embedded into a polypyrrole (PPy) layer, sandwiched between two pure PPy films, electrodeposited on a graphite support were investigated for electrocatalysis of the oxygen reduction reaction (ORR). PPy and PPy(La_1−xSr_xMnO₃) (0≤ x ≤0.4) successive layers have been obtained on polished and pretreated graphite electrodes following sequential electrodeposition technique. The electrolytes used in the electrodeposition process were Ar saturated 0.1 mol dm⁻³ pyrrole (Py) plus 0.05 mol dm⁻³ K₂SO₄ with and without containing a suspension of 8.33 g L⁻¹ oxide powder. Films were characterized by XRD, SEM, linear sweep voltammetry, cyclic voltammetry (CV) and electrochemical impedance (EI) spectroscopy. Electrochemical investigations were carried out at pH 12 in a 0.5 mol dm⁻³ K₂SO₄ plus 5 mmol dm⁻³ KOH, under both oxygenated and deoxygenated conditions. Results indicate that the porosity of the PPy matrix is considerably enhanced in presence of oxide particles. Sr substitution is found to have little influence on the electrocatalytic activity of the composite electrode towards the ORR. However, the rate of oxygen reduction decreases with decreasing pH of the electrolyte from pH 12 to pH 6. It is noteworthy that in contrast to a non-composite electrode of the same oxide in film form, the composite electrode exhibits much better electrocatalytic activity for the ORR.     

Synthesis and characterization of ZnxMg1 − xGa2O4:Co fabricated by low-temperature burning method

A series of Zn_xMg_1 − xGa₂O₄:Co²⁺ spinels (x = 0, 0.25, 0.5, 0.75, and 1.0) was successfully produced through low-temperature burning method by using Mg(NO₃)₂·4H₂O, Zn(NO₃)₂·6H₂O, Ga(NO₃)₃·6H₂O, CO(NH₂)₂, NH₄NO₃, and Co(NO₃)₂·6H₂O as raw materials. The product was characterized by X-ray diffraction, transmission electron microscopy, and photoluminescence spectroscopy. The product was not merely a simple mixture of MgGa₂O₄ and ZnGa₂O₄; rather, it formed a solid solution. The lattice constant of Zn_xMg_1 − xGa₂O₄:Co²⁺ (0 ≤ x ≤ 1.0) crystals has a good linear relationship with the doping density, x. The synthesized products have high crystallinities with neat arrays. Based on an analysis of the form and position of the emission spectrum, the strong emission peak around the visible region (670 nm) can be attributed to the energy level transition [⁴T₁(⁴P) → ⁴A₂(⁴F)] of Co²⁺ in the tetrahedron. The weak emission peak in the near-infrared region can be attributed to the energy level transition [⁴T₁(⁴P) → ⁴T₂(⁴F)] of Co²⁺ in the tetrahedron.     

Sintering behavior and microwave dielectric properties of a new low-permittivity ceramic system Ca(Mg1−xAlx)(Si1−x/2Alx/2)2O6

The diopside ceramics with a formula of Ca(Mg_1−xAl_x)(Si_1−x/2Al_x/2)₂O₆ (x=0.01–0.3) were synthesized via a traditional solid-state reaction method, and their solid solubility, sintering behavior and microwave dielectric properties were investigated. The results revealed that the solubility limit of Al₂O₃ in Ca(Mg_1−xAl_x)(Si_1−x/2Al_x/2)₂O₆, which is defined as x, was between 0.15 and 0.2, and a second phase of CaAl₂SiO₆ presented when the x value reached 0.2. Appropriate Al³⁺ substitution for Mg²⁺ and Si⁴⁺ could promote the sintering process and lower the densification temperature, and a broadened densification temperature range of 1250–1300 °C was obtained for the compositions of x=0.08–0.15. With the increase of the x value, the dielectric constant (ε_r) increased roughly linearly, and the temperature coefficient of frequency (τ_f) showed a rising trend. The Q×f values increased from 57,322 GHz to 59,772 GHz as the x value increased from 0.01 to 0.08, and then they were saturated in the range of x=0.08–0.2. Further increase of the x value (x≥0.25) deteriorated the microwave dielectric properties. Good microwave dielectric properties of ε_r=7.89, Q×f=59,772 GHz and τ_f=−42.12 ppm/°C were obtained for the ceramics with the composition of x=0.08 sintered at 1275 °C.     

Preparation and cycling performance of Aland F co-substituted compounds Li4AlxTi5−xFyO12−y

Li₄Al_xTi_5−xF_yO_12−y compounds were prepared by a solid-state reaction method. Phase analyses demonstrated that both Al³⁺ and F⁻ ions entered the structure of spinel-type Li₄Ti₅O₁₂. Charge-discharge cycling results at a constant current density of 0.15 mA cm⁻² between the cut-off voltages of 2.5 and 0.5 V showed that the Al³⁺ and F⁻ substitutions improved the first total discharge capacity of Li₄Ti₅O₁₂. However, Al³⁺ substitution greatly increased the reversible capacity and cycling stability of Li₄Ti₅O₁₂ while F⁻ substitution decreased its reversible capacity and cycling stability slightly. The electrochemical performance of the Al³⁺-F⁻-co-substituted specimen was better than the F⁻-substituted one but worse than the Al³⁺-substituted one.     

Evolution of the local structure and electrochemical properties of spinel LiNixMn2−xO4 (0 ≤ x ≤ 0.5)

A series of Ni substituted spinel LiNi_xMn_2−xO₄ (0 ≤ x ≤ 0.5) have been synthesized to study the evolution of the local structure and their electrochemical properties. X-ray diffraction showed a few Ni cations moved to the 8a sites in heavily substituted LiNi_xMn_2−xO₄ (x ≥ 0.3). X-ray photoelectron spectroscopy confirmed Ni²⁺ cations were partially oxidized to Ni³⁺. The local structures of LiNi_xMn_2−xO₄ were studied by analyzing the and A_1g Raman bands. The most compact [Mn(Ni)O₆] octahedron with the highest bond energy of Mn(Ni)O was found for LiNi_0.2Mn_1.8O₄, which showed a Mn(Ni)O average bond length of 1.790 Å, and a force constant of 2.966 N cm⁻¹. Electrolyte decomposition during the electrochemical charging processes increased with Ni substitution. The discharge capacities at the 4.1 and 4.7 V plateaus obeyed the linear relationships with respect to the Ni substitution with the slopes of −1.9 and +1.9, which were smaller than the theoretical values of −2 and +2, respectively. The smaller slopes could be attributed to the electrochemical hysteresis and the presence of Ni³⁺ in the materials.     

Preparation and characterization of negative thermal expansion Sc2W3O12/Cu core-shell composite

A composite of Sc₂W₃O₁₂/Cu where Sc₂W₃O₁₂, the core, is coated by the Cu shell was synthesized using simple electroless plating method. As-prepared Sc₂W₃O₁₂/Cu composites were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectrometry (EDS) and thermomechanical analyzer (TMA) techniques. The study results show that the Pd-Sn activator was successfully formed on the surface of Sc₂W₃O₁₂ after the sensitization and activation. In the electroless plating process, Cu nanocrystals formed firstly, and then grew together to form a continuous coating. Sc₂W₃O₁₂/Cu core-shell composites exhibit a negative linear coefficient of thermal expansion CTE = −4.47 × 10⁻⁶ °C⁻¹ from room temperature to 200 °C.     

Effect of double doping on crystal structure and electrical conductivity of CaO and WO3-doped Bi2O3

The atomic arrangement of WO₃-doped Bi₂O₃ was found similar to that of the fluorite structure. However, the electrical conductivity of WO₃-doped Bi₂O₃ is significantly lower than that of commonly used Y₂O₃-doped Bi₂O₃. The structure and electrical conductivity of samples formulated as (Ca_xW_0.15Bi_0.85−x)₂O_3.45−x (x = 0, 0.1, 0.2 and 0.3) were investigated. The as-sintered (W_0.15Bi_0.85)₂O_3.45 and (Ca_0.1W_0.15Bi_0.75)₂O_3.35 exhibit similar single tetragonal structure that is isostructural with 7Bi₂O₃·2WO₃. Therefore, (W_0.15Bi_0.85)₂O_3.45 and (Ca_0.1W_0.15Bi_0.75)₂O_3.35 formed a superstructure consisting of 10 enlarged cubic fluorite subcells. However, the as-sintered samples consist of a tetragonal structure and tetragonal CaWO₄ for x = 0.2 and 0.3 because the oxygen vacancy concentration increases. The conductivities of (Ca_xW_0.15Bi_0.85−x)₂O_3.45−x (x = 0, 0.1, 0.2 and 0.3) did not exhibit linear dependence with x value. The best conductivity is 2.35 × 10⁻² S cm⁻¹ at 700 °C for x = 0.1 that is higher than that of Ca-free (W_0.15Bi_0.85)₂O_3.45. The higher conductivity of (Ca_0.1W_0.15Bi_0.75)₂O_3.35 than (W_0.15Bi_0.85)₂O_3.45 may result from the higher anion vacancy concentration and more symmetrical structure.