Thermoplastic elastomers based on high‐density polyethylene,ethylene–propylene–diene terpolymer,and ground tire rubber dynamically vulcanized with dicumyl peroxide

Thermoplastic vulcanizates (TPVs) based on high‐density polyethylene (HDPE), ethylene–propylene–diene terpolymer (EPDM), and ground tire rubber (GTR) were dynamically vulcanized with dicumyl peroxide (DCP). The polymer blend was composed of 40% HDPE, 30% EPDM, and 30% GTR, and the concentration of DCP was varied from 0.3 to 3.6 parts per hundred rubber (phr). The properties of the TPVs were determined by evaluation of the gel fraction content and the mechanical properties. In addition, IR spectroscopy and differential scanning calorimetry analysis were performed as a function of the DCP content. Decreases in the Young's modulus of the blends and the crystallinity of HDPE were observed when the content of DCP was greater than 1.8 phr. The results regarding the gel content indicate that the presence of DCP promoted the crosslinking of the thermoplastic matrix, and optimal properties were obtained with 1.5% DCP. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39901.     

Preparation and characterization of acrylonitrile–styrene–methylmethacrylate terpolymer as a compatibilizer for rubber blends

Acrylonitrile‐co‐styrene‐co‐methylmethacrylate (AN‐S‐MMA) terpolymer was prepared by bulk and emulsifier‐free emulsion polymerization techniques. The bulk and emulsion terpolymers were characterized by means of Fourierr transform infrared spectroscopy, ¹³C nuclear magnetic resonance (NMR) spectroscopy, gel permeation chromatography, thermal gravimetric analysis, and elemental analysis. The kinetics of the terpolymerization were studied. The terpolymers were then incorporated into butadiene—acrylonitrile rubber (NBR)/ethylene propylene diene monomer rubber (EPDM) blends and into chloroprene rubber (CR)/EPDM blend. The terpolymers were then tested for potential as compatibilizers by using scanning electron microscopy and differential scanning calorimetry. The terpolymers improved the compatibility of CR/EPDM and NBR/EPDM blends. The physicomechanical properties of CR/EPDM and NBR/EPDM blend vulcanizates revealed that the incorporation of terpolymers was advantageous, since they resulted in blend vulcanizates with higher 100% moduli and with more thermally stable mechanical properties than the individual rubbers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3143–3153, 2003     

Thermal and mechanical properties of silicon rubber/cis‐polybutadiene rubber/ethylene–propylene–diene monomer blends

Considering the properties of silicon rubber, ethylene–propylene–diene monomer (EPDM), and cis‐polybutadiene rubber (BR), a blend made by a new method was proposed in this article; this blend had thermal resistance and good mechanical properties. The morphology of the blend was studied by SEM, and it was found that the adhesion between the phases of BR, EPDM, and polysiloxanes (silicon rubber) could be enhanced, and the compatibility and covulcanization were good. The influence of the mass ratio of peroxide and silica on the mechanical properties and thermal resistance of the blend was studied. The results showed that the mechanical properties and thermal resistance of the blend were improved when silicon rubber/BR/EPDM was 20/30/50, dicumyl peroxide/sulfur was 2.5/2.5, and the amount of silica was 80 phr. The integral properties of rubber blend had more advantages than did the three rubbers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4462–4467, 2006     

Effects of shear stress and subcritical water on devulcanization of styrene–butadiene rubber based ground tire rubber in a twin‐screw extruder

The devulcanization reaction of styrene–butadiene rubber (SBR) based ground tire rubber (GTR) in GTR/ethylene–propylene–diene monomer rubber (EPDM) blend was investigated through a compound‐induced reaction by increasing screw rotation speed and being in the presence of subcritical water. The effects of temperature, pressure, screw rotation speed, or promoting agents on the gel content, Mooney viscosity, and Fourier transform infrared spectra of the sol of the devulcanized blends (devulcanized ground tire rubber (DGTR)/EPDM) were measured, and the mechanical properties and microstructures of the revulcanized blend ((DGTR/EPDM)/SBR) were characterized. The results show that subcritical water as a swelling agent and reaction medium promotes the devulcanization reaction, increases the selectivity of the crosslink breakage, keeps the extrusion material from oxidative degradation, reduces the gel particle size of the devulcanized blends, and significantly improves the mechanical properties of the revulcanized SBR/(DGTR/EPDM) blends. In subcritical water, the suitable promoting agents (alkylphenol polysulfide 450, hydrogen peroxide H₂O₂, or 450/H₂O₂) accelerate the devulcanization reaction, keep the double bond content, and lead to further decrease of the gel content and Mooney viscosity of the devulcanized blends and further increase of the mechanical properties of the revulcanized SBR/(DGTR/EPDM) blends. Especially the compound promoting agent (450/H₂O₂) improves the selectivity of the crosslink breakage in devulcanization of SBR‐based GTR. When 450/H₂O₂ is added as a compound promoting agent at the best reaction condition in subcritical water (200°C, 1.6 MPa and 1000 rpm), the tensile strength and elongation at break of the revulcanized SBR/(DGTR/EPDM) blends reach to 85.4% and 201% of vulcanized SBR (24.0 MPa, 356%), respectively. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1845–1854, 2013     

Dynamic mechanical analysis of ethylene–propylene–diene monomer rubber and styrene–butadiene rubber blends

The effects of blend ratio, crosslinking systems, and fillers on the viscoelastic response of ethylene–propylene–diene monomer (EPDM)/styrene–butadiene rubber (SBR) blends were studied as functions of frequency, temperature, and cure systems. The storage modulus decreased with increasing SBR content. The loss modulus and loss tangent results showed that the EPDM/SBR blend vulcanizate containing 80 wt % EPDM had the highest compatibility. Among the different cure systems studied, the dicumyl peroxide cured blends exhibited the highest storage modulus. The reinforcing fillers were found to reduce the loss tangent peak height. The blend containing 40 wt % EPDM showed partial miscibility. The dispersed EPDM phase suppressed the glass‐transition temperature of the matrix phase. The dynamic mechanical response of rubbery region was dominated by SBR in the EPDM–SBR blend. The morphology of the blend was studied by means of scanning electron microscopy. The blend containing 80 wt % EPDM had small domains of SBR particles dispersed uniformly throughout the EPDM matrix, which helped to toughen the matrix and prevent crack propagation; this led to enhanced blend compatibility. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Thermoplastic dynamic vulcanisates containing LDPE,rubber, and thermochemically reclaimed ground tyre rubber

Abstract

Thermochemically devulcanised ground tyre rubber (GTR^DL) was added to fresh rubber compositions, which were then melt blended with low density polyethylene (LDPE). Styrene/butadiene rubber (SBR), natural (NR), and ethylene/propylene/diene (EPDM) rubbers were selected as the fresh rubbers. During blending, dynamic curing was achieved using sulphuric, phenolic, and peroxide curing agents. Some of the GTR was decomposed in the presence of 6 phr Regen^TM Agent-S reclaiming compound before being incorporated into the blends. The resulting thermoplastic dynamic vulcanisates had constant compositions, namely LDPE/rubber/GTR=50:25:25. Sulphuric and phenolic curing agents proved to be most suitable for dynamic curing. The thermoplastic dynamic vulcanisates with the best mechanical performance contained SBR and EPDM rubbers. The observed improvements in mechanical performance were attributed to chain entanglement and co-crosslinking in the interphase between the GTR^DL particles and the surrounding matrix (i.e. with the fresh rubber and/or LDPE). The phase morphology, which was assessed using scanning electron microscopy on the etched surfaces of cryogenically fractured thermoplastic dynamic vulcanisate compositions, is discussed.     

Cure characteristics,morphology, and mechanical properties of ethylene–propylene–diene–monomer rubber/acrylonitrile butadiene rubber blends

Blends based on ethylene–propylene–diene monomer rubber (EPDM) and acrylonitrile butadiene rubber (NBR) was prepared. Sulfur was used as the vulcanizing agent. The effects of blend ratio on the cure characteristics and mechanical properties, such as stress–strain behavior, tensile strength, elongation at break, hardness, rebound resilience, and abrasion resistance have been investigated. Tensile and tear strength showed synergism for the blend containing 30% of NBR, which has been explained in terms of morphology of the blends attested by scanning electron micrographs. A relatively cocontinuous morphology was observed for 70 : 30, EPDM/NBR blend system. The experimental results have been compared with the relevant theoretical models. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Study on the milling behavior of chloroprene rubber blends with ethylene–propylene–diene monomer rubber,polybutadiene rubber,and natural rubber

The viscoelastic properties of the blends of chloroprene rubber (CR) with ethylene–propylene–diene monomer rubber (EPDM), polybutadiene rubber (BR), and natural rubber (NR) at different temperature were studied using rubber processing analyzer (RPA). Mooney viscosities of compounds were measured and tight milling and sheeting appearance were observed on a two‐roll mill. The results showed that Mooney viscosities and the elastic modulus of the blends decreased with the increase of the temperature from 60 to 100°C. And the decreasing trends of pure CR, pure NR, and CR/NR blend compounds were more prominent than that of pure EPDM, pure BR, CR/EPDM, and CR/BR blend compounds. For CR/EPDM blend compounds, the decreasing trend became slower with the increase of EPDM ratio in the blend. Compared with pure CR, pure NR and CR/NR blend compounds, pure EPDM, pure BR compounds, and the blend compounds of CR/EPDM and CR/BR showed less sensibility to temperature and they were less sticky to the metal surface of rolls and could be kept in elastic state at higher temperature, easy to be milled up and sheeted. At the same blend ratio and temperature, the property of tight milling of the blends decreased in the sequence of CR/EPDM, CR/BR, and CR/NR. With the increase of EPDM, BR, or NR ratio in CR blends, its property of tight milling was improved. POLYM. COMPOS., 28:667–673, 2007. © 2007 Society of Plastics Engineers     

Influence of phase modifiers on morphology and properties of thermoplastic elastomers prepared from ethylene propylene diene rubber and isotactic polypropylene

A series of thermoplastic elastomers (TPEs) were prepared from a binary blend of ethylene propylene diene rubber (EPDM) and isotactic polypropylene (iPP) using different types of phase modifiers. The influence of sulphonated EPDM, maleated EPDM, styrene‐ethylene‐co‐butylene‐styrene block copolymer, maleated PP, and acrylated PP as phase modifiers showed improved physico‐mechanical properties (like maximum stress, elongation at break, moduli, and tension set). Scanning electron and atomic force microscopy studies revealed better morphologies obtained with these phase modified EPDM‐iPP blends. The dependence of the phase modifier type and concentration was optimized with respect to the improvement in physical properties and morphology of the blends. Physical properties, dynamic mechanical properties, and morphology of these blends were explained with the help of interaction parameter, melt viscosity, and crystallinity of the blends. Theoretical modeling showed that Kerner, Ishai‐Cohen, and Paul models predicted the right morphology–property correlation for the prepared TPEs. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers.     

Mechanical properties,morphological structure,and thermal behavior of dynamically photocrosslinked PP/EPDM blends

A dynamically photocrosslinked polypropylene (PP)/ethylene–propylene–diene (EPDM) rubber thermoplastic elastomer was prepared by simultaneously exposing the elastomer to UV light while melt‐mixing in the presence of a photoinitiator as well as a crosslinking agent. The effects of dynamic photocrosslinking and blend composition on the mechanical properties, morphological structure, and thermal behavior of PP/EPDM blends were investigated. The results showed that after photocrosslinking, tensile strength, modulus of elasticity, and elongation at break were improved greatly. Moreover, the notched Izod impact strength was obviously enhanced compared with corresponding uncrosslinked blend. Scanning electron microscopy (SEM) morphological analysis showed that for uncrosslinked PP/EPDM blends, the cavitation of EPDM particles was the main toughening mechanism; whereas for dynamically photocrosslinked blends, shear yielding of matrix became the main energy absorption mechanism. The DSC curves showed that for each dynamically photocrosslinked PP/EPDM blend, there was a new smaller melting peak at about 152°C together with a main melting peak at about 166°C. Dynamic mechanical thermal analysis (DMTA) indicated that the compatibility between EPDM and PP was improved by dynamic photocrosslinking. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3371–3380, 2004     

The morphology and property of ultra‐fine full‐vulcanized acrylonitrile butadiene rubber particles/EPDM blends

A novel UFNBRP/EPDM blend was prepared by compounding ultra‐fine full‐vulcanized acrylonitrile butadiene rubber particles (UFNBRP) with ethylene–propylene–diene monomer (EPDM) matrix. The morphology, dynamic property, and curing property of the blend were discussed in detail. TEM and SEM observations showed that, no matter how high the blend ratio of UFNBRP to EPDM matrix was, UFNBRP particles always kept being in the dispersion phase because of its extremely high viscosity resulting from self‐crosslinking, but were not dispersed as nanosize units, as expected. Dynamic properties, illustrated by DMTA, further demonstrated that two phases exhibited two separate glass transition temperatures, indicating distinct phase separation and weak phase interaction. Rubber processing analyzer results showed that inorganic filler as well as UFNBRP particles in EPDM matrix formed a network and blocked the flow properties of the compound. At the same time, the introduction of UFNBRP particles evidently affected the vulcanization of EPDM, when sulfur was used as a vulcanizing agent, and improved the mechanical properties of EPDM. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3673–3679, 2006     

Effect of the addition of acrylonitrile/ethylene–propylene–diene monomer (EPDM)/styrene graft copolymer on the morphology–properties relationships in poly(styrene‐co‐acrylonitrile)/EPDM rubber blends

Blends of poly(styrene‐co‐acylonitrile) (SAN) with ethylene–propylene–diene monomer (EPDM) rubber were investigated. An improved toughness–stiffness balance of the SAN/EPDM blend was obtained when an appropriate amount of acrylonitrile–EPDM–styrene (AES) graft copolymer was added, prepared by grafting EPDM with styrene–acrylonitrile copolymer, and mixed thoroughly with both of the two components of the blend. Morphological observations indicated a finer dispersion of the EPDM particles in the SAN/EPDM/AES blends, and particle size distribution became narrower with increasing amounts of AES. Meanwhile, it was found that the SAN/EPDM blend having a ratio of 82.5/17.5 by weight was more effective in increasing the impact strength than that of the 90/10 blend. From dynamic mechanic analysis of the blends, the glass‐transition temperature of the EPDM‐rich phase increased from ?53.9 to ?46.2°C, even ?32.0°C, for the ratio of 82.5/17.5 blend of SAN/EPDM, whereas that of the SAN‐rich phase decreased from 109.2 to 108.6 and 107.5°C with the additions of 6 and 10% AES copolymer contents, respectively. It was confirmed that AES graft copolymer is an efficient compatibilizer for SAN/EPDM blend. The compatibilizer plays an important role in connecting two phases and improving the stress transfer in the blends. Certain morphological features such as thin filament connecting and even networking of the dispersed rubber phase may contribute to the overall ductility of the high impact strength of the studied blends. Moreover, its potential to induce a brittle–ductile transition of the glassy SAN matrix is considered to explain the toughening mechanism. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1685–1697, 2004     

Characterization and properties of LDPE/(ground tire rubber)/crosslinked butyl rubber blends

In recent years, interest in used rubber recycling, mainly focusing on the utilization of end‐of‐life tires, has heightened. This interest, is owing to the activities related to environmental protection and economic factors, which both stimulate companies to reuse the high‐quality rubber present in ground rubber scrap. In this study, the application of crosslinked butyl rubber in thermoplastic compositions of low‐density polyethylene and ground tire rubber (GTR) is presented. The static and dynamic mechanical properties and morphology of obtained products were studied. The addition of crosslinked butyl rubber to the investigated blends increased the compatibility between the low‐density polyethylene and the GTR particles. It was found that the mechanical properties of thermoplastic compositions containing higher amounts of elastomers (i.e., GTR and crosslinked butyl elastomer) displayed the same behavior, whereas the samples with GTR had worse respective parameters. Depending on their composition, the obtained new polymer blends can be applied to automotive parts, be adapted to pavement surfaces, and become parts of antivibration systems. J. VINYL ADDIT. TECHNOL., 20:237–242, 2014. © 2014 Society of Plastics Engineers     

Studies on blends of natural rubber and ethylene propylene diene rubber modified with phosphorylated cardanol prepolymer: Processability,physico‐mechanical properties,and morphology

The melt processability and physico‐mechanical properties of blends of natural rubber (NR) and ethylene propylene diene rubber (EPDM) containing different dosages (0–10 phr) of phosphorylated cardanol prepolymer (PCP) were studied in unfilled and china‐clay‐filled mixes. The plasticizing effect of PCP in the blends was evidenced by progressive reduction in power consumption of the mixing and activation energy for melt flow with an increase in the dosage of PCP. The PCP‐modified blend vulcanizates showed higher tensile properties and tear strength despite a decrease in the chemical crosslink density (CLD) index. This is presumably due to the formation of a crosslinked network structure of PCP with the rubbers and improved dispersion of the filler particles in the rubber matrix, as evidenced by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Thermogravimetric analysis showed an increase in thermal stability of the blend vulcanizate in presence of 5 phr of PCP. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5123–5130, 2006     

Synthesis of high rubber styrene–EPDM–acrylonitrile graft copolymer and its toughening effect on SAN

High rubber styrene–EPDM–acrylonitrile (AES) was prepared by the graft copolymerization of styrene (St) and acrylonitrile (AN) onto ethylene–propylene–diene terpolymer (EPDM) in n‐heptane/toluene cosolvent using benzoyl peroxide as an initiator. The effects of reaction conditions, such as reaction temperature, initiator concentration, EPDM content, the solvent component, and reaction time, on the graft copolymerization are discussed. In addition, according to the research on mechanical properties of the SAN/AES blend, a remarkable toughening effect of AES on SAN resin was found. By means of scanning electron microscopy, the toughening mechanism is proposed to be crazing initiation from rubber particles and shear deformation of SAN matrix. Uniform dispersion of rubber particles, as shown by transmission electron microscopy, is attributed to the good compatibility of SAN and AES. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 416–423, 2004     

Properties and morphologies of elastomer blends modified with EPDM‐g‐poly[2‐dimethylamino ethylmethacrylate]

The graft copolymerization of 2‐dimethylamino ethylmethacrylate (DMAEMA) onto ethylene propylene diene mononer rubber (EPDM) was carried out in toluene via solution polymerization technique at 70°C, using dibenzoyl peroxide as initiator. The synthesized EPDM rubber grafted with poly[DMAEMA] (EPDM‐g‐PDMAEMA) was characterized with ¹H‐NMR spectroscopy, gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and thermal gravimetric analysis (TGA). The EPDM‐g‐PDMAEMA was incorporated into EPDM/butadiene acrylonitrile rubber (EPDM/NBR) blend with different blend ratios, where the homogeneity of such blends was examined with scanning electron microscopy and DSC. The scanning electron micrographs illustrate improvement of the morphology of EPDM/NBR rubber blends as a result of incorporation of EPDM‐g‐PDMAEMA onto that blend. The DSC trace exhibits one glass transition temperature (T_g) for EPDM/NBR blend containing EPDM‐g‐PDMAEMA, indicating improvement of homogeneity. The physico‐mechanical properties after and before accelerated thermal aging of the homogeneous, and inhomogeneous EPDM/NBR vulcanizates with different blend ratios were investigated. The physico‐mechanical properties of all blend vulcanizates were improved after and before accelerated thermal aging, in presence of EPDM‐g‐PDMAEMA. Of all blend ratios under investigation EPDM/NBR (75/25) blend possesses the best physico‐mechanical properties together with the best (least) swelling (%) in brake fluid. Swelling behavior of the rubber blend vulcanizates in motor oil and toluene was also investigated. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of bis(diisopropyl)thiophosphoryl disulfide on the covulcanization of styrene–butadiene rubber and ethylene–propylene–diene (monomer) blends

Covulcanization of elastomer blends constituting styrene–butadiene rubber (SBR) and ethylene–propylene–diene (monomer) rubber (EPDM) was successfully performed in the presence of reinforcing fillers like carbon black and silica by using a multifunctional rubber additive, bis(diisopropyl)thiophosphoryl disulfide (DIPDIS). The polarity of EPDM rubber was increased by a two‐stage vulcanization technique, which allowed the formation of rubber‐bound intermediates. In this way the migration of both curatives and reinforcing fillers in the EPDM–SBR blend could be controlled and cure rate mismatch could be minimized. The process significantly improved the physical properties of the blend vulcanizates. The phase morphology, as evident from the SEM micrographs, was indicative of the presence of a much more compact and coherent rubber matrix in the two‐stage vulcanizates. Different accelerator systems were studied to understand better the function and effectiveness of DIPDIS in developing homogeneity in the blends of dissimilar elastomers. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1231–1242, 2004     

Polypropylene/natural rubber thermoplastic elastomer: Effect of phenolic resin as a vulcanizing agent on mechanical properties and morphology

The aim of this study is to characterize thermoplastic elastomers (TPEs) from polypropylene and natural rubber with and without phenolic resin as a vulcanizing agent. The blends containing 40–60 wt % of polypropylene were mixed in an internal mixer and pressed with a compression molding machine. TPEs without rubber vulcanization, named as unvulcanized thermoplastic natural rubber (uTPNR) were compared to TPEs containing dynamic vulcanized rubber, referred as vulcanized thermoplastic natural rubber (vTPNR). The uTPNRs illustrated cocontinuous phase morphology, whereas the vTPNRs displayed dispersed phase of vulcanized natural rubber. Tensile properties, tear strength, thermal ageing resistance, ozone resistance, tension set, hardness and swelling test in toluene, IRM 903 oil and engine oil were carried out according to ASTM. It was found that tensile and tear strength, hardness and tension set of the uTPNRs increased with increasing polypropylene content. Dynamic vulcanization improved tensile strength, elongation at break, tension set and degree of swelling of the TPEs, whereas hardness and tear strength did not show significant change after dynamic vulcanization. The vTPNRs exhibited higher ozone resistance and swelling resistance than the uTPNRs. Reprocessability of the vTPNRs was investigated and showed that tensile strength decreased at 20 and 30% and elongation at break decreased at 13 and 27% for the first and the third reprocessing respectively. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Recycling of EPDM waste. II. Replacement of virgin rubber by ground EPDM vulcanizate in EPDM/PP thermoplastic elastomeric composition

Virgin ethylene propylene diene monomer (EPDM) rubber in a thermoplastic elastomeric blend of polypropylene (PP) and EPDM rubber was substituted by ground EPDM vulcanizate of known composition, after which the mechanical properties of the raw EPDM/waste EPDM/PP blends were determined. The ratio of the rubber content in the waste EPDM (r‐W‐EPDM) to the raw EPDM (R‐EPDM) in the blends was varied from 0 : 100 to 45 : 55. Attempts to replace higher amounts (>45%) of R‐EPDM by W‐EPDM failed because of processing difficulty. Although a drop in mechanical properties of the blends was observed at lower loadings of W‐EPDM, the properties showed improvement at intermediate W‐EPDM loadings. The R‐EPDM/W–EPDM/PP blends were found to be reprocessable. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 3304–3312, 2001     

Effects of interface reactions in compatibilised ground tyre rubber polypropylene elastomeric alloys

Abstract

Compounds of ground tyre rubber (GTR) and polypropylene (PP) were prepared in an internal mixer and characterised by means of mechanical, thermal and morphological testing. Only physical melt mixing could not provide a suitable interface compatibilisation and leads to compounds with poor mechanical properties. However, the application of a reactive melt mixing process, using organic peroxides as radical donators, was found to be suitable to initiate a compatibilisation reaction via interphase grafting. These compatibilised GTR/PP elastomeric alloy (EA) systems exhibit interesting mechanical properties which are close to that of conventional two phase thermoplastic elastomers (TPE) based on dynamically vulcanised ethylene propylene diene monomer (EPDM)/PP blends. Results of the morphology investigations substantiate the occurrence of a compatibilisation reaction between rubber particles and PP matrix during reactive mixing which is most probably responsible for the enhanced material properties of the GTR/PP EA.